Abstract: The release of heavy metals into the environment has increased over the last years. In this study, 25 soil samples (0-15 cm) from the fields near the mining area in Drama region were selected. The samples were analyzed in the laboratory for their physicochemical properties and for seven “pseudo-total’’ heavy metals content, namely Pb, Zn, Cd, Cr, Cu, Ni, and Mn. The total metal concentrations (Pb, Zn, Cd, Cr, Cu, Ni and Mn) in digests were determined by using the atomic absorption spectrophotometer. According to the results, the mean concentration of the listed heavy metals in 25 soil samples are Cd 1.1 mg/kg, Cr 15 mg/kg, Cu 21.7 mg/kg, Ni 30.1 mg/kg, Pd 50.8 mg/kg, Zn 99.5 mg/kg and Mn 815.3 mg/kg. The results show that the heavy metals remain in the soil even if the mining closed many years ago.
Abstract: Integrated resilience engineering (IRE) is capable of returning banking systems to the normal state in extensive economic circumstances. In this study, information system of a large bank (with several branches) is assessed and optimized under severe economic conditions. Data envelopment analysis (DEA) models are employed to achieve the objective of this study. Nine IRE factors are considered to be the outputs, and a dummy variable is defined as the input of the DEA models. A standard questionnaire is designed and distributed among executive managers to be considered as the decision-making units (DMUs). Reliability and validity of the questionnaire is examined based on Cronbach's alpha and t-test. The most appropriate DEA model is determined based on average efficiency and normality test. It is shown that the proposed integrated design provides higher efficiency than the conventional RE design. Results of sensitivity and perturbation analysis indicate that self-organization, fault tolerance, and reporting culture respectively compose about 50 percent of total weight.
Abstract: Centrifugal-casting machine is used in manufacturing
special machine components like multi-layer journal bearing used in
all internal combustion engine, steam, gas turbine and air craft turboengine
where isotropic properties and high precisions are desired.
Moreover, this machine can be used in manufacturing thin wall hightech
machine components like cylinder liners and piston rings of IC
engine and other machine parts like sleeves, and bushes. Heavy-duty
machine component like railway wheel can also be prepared by
centrifugal casting. A lot of technological developments are required
in casting process for production of good casted machine body and
machine parts. Usually defects like blowholes, surface roughness,
chilled surface etc. are found in sand casted machine parts. But these
can be removed by centrifugal casting machine using rotating
metallic die. Moreover, die rotation, its temperature control, and good
pouring practice can contribute to the quality of casting because of
the fact that the soundness of a casting in large part depends upon
how the metal enters into the mold or dies and solidifies. Poor
pouring practice leads to variety of casting defects such as
temperature loss, low quality casting, excessive turbulence, over
pouring etc. Besides these, handling of molten metal is very
unsecured and dangerous for the workers. In order to get rid of all
these problems, the need of an automatic pouring device arises. In
this research work, a robot assisted pouring device and a centrifugal
casting machine are designed, developed constructed and tested
experimentally which are found to work satisfactorily. The robot
assisted pouring device is further modified and developed for using it
in actual metal casting process. Lot of settings and tests are required
to control the system and ultimately it can be used in automation of
centrifugal casting machine to produce high-tech machine parts with
desired precision.
Abstract: Recent research in neural networks science and
neuroscience for modeling complex time series data and statistical
learning has focused mostly on learning from high input space and
signals. Local linear models are a strong choice for modeling local
nonlinearity in data series. Locally weighted projection regression is
a flexible and powerful algorithm for nonlinear approximation in
high dimensional signal spaces. In this paper, different learning
scenario of one and two dimensional data series with different
distributions are investigated for simulation and further noise is
inputted to data distribution for making different disordered
distribution in time series data and for evaluation of algorithm in
locality prediction of nonlinearity. Then, the performance of this
algorithm is simulated and also when the distribution of data is high
or when the number of data is less the sensitivity of this approach to
data distribution and influence of important parameter of local
validity in this algorithm with different data distribution is explained.
Abstract: In this paper a real-time obstacle avoidance approach
for both autonomous and non-autonomous dynamical systems (DS) is
presented. In this approach the original dynamics of the controller
which allow us to determine safety margin can be modulated.
Different common types of DS increase the robot’s reactiveness in
the face of uncertainty in the localization of the obstacle especially
when robot moves very fast in changeable complex environments.
The method is validated by simulation and influence of different
autonomous and non-autonomous DS such as important
characteristics of limit cycles and unstable DS. Furthermore, the
position of different obstacles in complex environment is explained.
Finally, the verification of avoidance trajectories is described through
different parameters such as safety factor.
Abstract: In this paper, Bayesian online inference in models of
data series are constructed by change-points algorithm, which
separated the observed time series into independent series and study
the change and variation of the regime of the data with related
statistical characteristics. variation of statistical characteristics of time
series data often represent separated phenomena in the some
dynamical system, like a change in state of brain dynamical reflected
in EEG signal data measurement or a change in important regime of
data in many dynamical system. In this paper, prediction algorithm
for studying change point location in some time series data is
simulated. It is verified that pattern of proposed distribution of data
has important factor on simpler and smother fluctuation of hazard
rate parameter and also for better identification of change point
locations. Finally, the conditions of how the time series distribution
effect on factors in this approach are explained and validated with
different time series databases for some dynamical system.
Abstract: In this paper, we considered and applied parametric
modeling for some experimental data of dynamical system. In this
study, we investigated the different distribution of output
measurement from some dynamical systems. Also, with variance
processing in experimental data we obtained the region of
nonlinearity in experimental data and then identification of output
section is applied in different situation and data distribution. Finally,
the effect of the spanning the measurement such as variance to
identification and limitation of this approach is explained.
Abstract: In this paper, model order reduction method is used
for approximation in linear and nonlinearity aspects in some
experimental data. This method can be used for obtaining offline
reduced model for approximation of experimental data and can
produce and follow the data and order of system and also it can
match to experimental data in some frequency ratios. In this study,
the method is compared in different experimental data and influence
of choosing of order of the model reduction for obtaining the best and
sufficient matching condition for following the data is investigated in
format of imaginary and reality part of the frequency response curve
and finally the effect and important parameter of number of order
reduction in nonlinear experimental data is explained further.
Abstract: Performance of different filtering approaches depends
on modeling of dynamical system and algorithm structure. For
modeling and smoothing the data the evaluation of posterior
distribution in different filtering approach should be chosen carefully.
In this paper different filtering approaches like filter KALMAN,
EKF, UKF, EKS and smoother RTS is simulated in some trajectory
tracking of path and accuracy and limitation of these approaches are
explained. Then probability of model with different filters is
compered and finally the effect of the noise variance to estimation is
described with simulations results.
Abstract: The final step to complete the “Analytical Systems
Engineering Process” is the “Allocated Architecture” in which all
Functional Requirements (FRs) of an engineering system must be
allocated into their corresponding Physical Components (PCs). At
this step, any design for developing the system’s allocated
architecture in which no clear pattern of assigning the exclusive
“responsibility” of each PC for fulfilling the allocated FR(s) can be
found is considered a poor design that may cause difficulties in
determining the specific PC(s) which has (have) failed to satisfy a
given FR successfully. The present study utilizes the Axiomatic
Design method principles to mathematically address this problem and
establishes an “Axiomatic Model” as a solution for reaching good
alternatives for developing the allocated architecture. This study
proposes a “loss Function”, as a quantitative criterion to monetarily
compare non-ideal designs for developing the allocated architecture
and choose the one which imposes relatively lower cost to the
system’s stakeholders. For the case-study, we use the existing design
of U. S. electricity marketing subsystem, based on data provided by
the U.S. Energy Information Administration (EIA). The result for
2012 shows the symptoms of a poor design and ineffectiveness due to
coupling among the FRs of this subsystem.
Abstract: A feasibility study for the design and construction of a
pilot plant for the extraction of castor oil in South Africa was
conducted. The study emphasized the four critical aspects of project
feasibility analysis, namely technical, financial, market and
managerial aspects. The technical aspect involved research on
existing oil extraction technologies, namely: mechanical pressing and
solvent extraction, as well as assessment of the proposed production
site for both short and long term viability of the project. The site is
on the outskirts of Nkomazi village in the Mpumalanga province,
where connections for water and electricity are currently underway,
potential raw material supply proves to be reliable since the province
is known for its commercial farming. The managerial aspect was
evaluated based on the fact that the current producer of castor oil will
be fully involved in the project while receiving training and technical
assistance from Sasol Technology, the TSC and SEDA. Market and
financial aspects were evaluated and the project was considered
financially viable with a Net Present Value (NPV) of R2 731 687 and
an Internal Rate of Return (IRR) of 18% at an annual interest rate of
10.5%. The payback time is 6years for analysis over the first 10
years with a net income of R1 971 000 in the first year. The project
was thus found to be feasible with high chance of success while
contributing to socio-economic development. It was recommended
for lab tests to be conducted to establish process kinetics that would
be used in the initial design of the plant.
Abstract: Sinc-collocation scheme is one of the new techniques
used in solving numerical problems involving integral equations. This
method has been shown to be a powerful numerical tool for finding
fast and accurate solutions. So, in this paper, some properties of the
Sinc-collocation method required for our subsequent development
are given and are utilized to reduce integral equation of the first
kind to some algebraic equations. Then convergence with exponential
rate is proved by a theorem to guarantee applicability of numerical
technique. Finally, numerical examples are included to demonstrate
the validity and applicability of the technique.
Abstract: This paper represents the results of long term strength of mortar incorporating Rice Husk Ash (RHA). For these work mortar samples were made according to ASTM standard C 109/C. OPC cement was partially replaced by RHA at 0, 10, 15, 20, 25 and 30 percent replacement level. After casting all samples were kept in controlled environment and curing was done up to 90 days. Test of mortar was performed on 3, 7, 28, 90, 365 and 700 days. It is noticed that OPC mortar shows better strength at early age than mortar having RHA but at 90 days and onward the picture is different. At 700 days it is observed that mortar containing 20% RHA shows better result than any other samples.
Abstract: There was a high rate of corrosion in Pyrolysis
Gasoline Hydrogenation (PGH) unit of Arak Petrochemical Company
(ARPC), and it caused some operational problem in this plant. A
commercial chemical had been used as anti-corrosion in the
depentanizer column overhead in order to control the corrosion rate.
Injection of commercial corrosion inhibitor caused some
operational problems such as fouling in some heat exchangers. It was
proposed to replace this commercial material with another more
effective trouble free, and well-known additive by R&D and
operation specialists.
At first, the system was simulated by commercial simulation
software in electrolytic system to specify low pH points inside the
plant. After a very comprehensive study of the situation and technical
investigations ,ammonia / monoethanol amine solution was proposed
as neutralizer or corrosion inhibitor to be injected in a suitable point
of the plant. For this purpose, the depentanizer column and its
accessories system was simulated again in case of this solution
injection.
According to the simulation results, injection of new anticorrosion
substance has no any side effect on C5 cut product and
operating conditions of the column. The corrosion rate will be
cotrolled, if the pH remains at the range of 6.5 to 8 . Aactual plant
test run was also carried out by injection of ammonia / monoethanol
amine solution at the rate of 0.6 Kg/hr and the results of iron content
of water samples and corrosion test coupons confirmed the
simulation results.
Now, ammonia / monoethanol amine solution is injected to a
suitable pint inside the plant and corrosion rate has decreased
significantly.
Abstract: The purpose of this paper is to investigate the
durability of cement mortar in presence of Rice Husk Ash (RHA).
The strength and durability of mortar with different replacement
level (0%, 10%, 15%, 20%, 25% and 30%) of Ordinary Portland
Cement (OPC) by RHA is investigated here. RHA was
manufactured from an uncontrolled burning process. Test samples
were prepared with river sand of FM 2.73. Samples were kept in
controlled environment up to test time. The results show that
addition of RHA was shown better results for 20% replacement
level than OPC at 90 days. In durability test all samples passed for
20 cycles except 25% and 30% replacement level.
Abstract: A number of studies highlighted problems related to
ERP systems, yet, most of these studies focus on the problems during
the project and implementation stages but not during the postimplementation
use process. Problems encountered in the process of
using ERP would hinder the effective exploitation and the extended
and continued use of ERP systems and their value to organisations.
This paper investigates the different types of problems users
(operational, supervisory and managerial) faced in using ERP and
how 'feral system' is used as the coping mechanism. The paper
adopts a qualitative method and uses data collected from two cases
and 26 interviews, to inductively develop a casual network model of
ERP usage problem and its coping mechanism. This model classified
post ERP usage problems as data quality, system quality, interface
and infrastructure. The model is also categorised the different coping
mechanism through use of 'feral system' inclusive of feral
information system, feral data and feral use of technology.
Abstract: The empirical mode decomposition (EMD) represents any time series into a finite set of basis functions. The bases are termed as intrinsic mode functions (IMFs) which are mutually orthogonal containing minimum amount of cross-information. The EMD successively extracts the IMFs with the highest local frequencies in a recursive way, which yields effectively a set low-pass filters based entirely on the properties exhibited by the data. In this paper, EMD is applied to explore the properties of the multi-year air temperature and to observe its effects on climate change under global warming. This method decomposes the original time-series into intrinsic time scale. It is capable of analyzing nonlinear, non-stationary climatic time series that cause problems to many linear statistical methods and their users. The analysis results show that the mode of EMD presents seasonal variability. The most of the IMFs have normal distribution and the energy density distribution of the IMFs satisfies Chi-square distribution. The IMFs are more effective in isolating physical processes of various time-scales and also statistically significant. The analysis results also show that the EMD method provides a good job to find many characteristics on inter annual climate. The results suggest that climate fluctuations of every single element such as temperature are the results of variations in the global atmospheric circulation.
Abstract: Recently, the issue of machine condition monitoring
and fault diagnosis as a part of maintenance system became global
due to the potential advantages to be gained from reduced
maintenance costs, improved productivity and increased machine
availability. The aim of this work is to investigate the effectiveness
of a new fault diagnosis method based on power spectral density
(PSD) of vibration signals in combination with decision trees and
fuzzy inference system (FIS). To this end, a series of studies was
conducted on an external gear hydraulic pump. After a test under
normal condition, a number of different machine defect conditions
were introduced for three working levels of pump speed (1000, 1500,
and 2000 rpm), corresponding to (i) Journal-bearing with inner face
wear (BIFW), (ii) Gear with tooth face wear (GTFW), and (iii)
Journal-bearing with inner face wear plus Gear with tooth face wear
(B&GW). The features of PSD values of vibration signal were
extracted using descriptive statistical parameters. J48 algorithm is
used as a feature selection procedure to select pertinent features from
data set. The output of J48 algorithm was employed to produce the
crisp if-then rule and membership function sets. The structure of FIS
classifier was then defined based on the crisp sets. In order to
evaluate the proposed PSD-J48-FIS model, the data sets obtained
from vibration signals of the pump were used. Results showed that
the total classification accuracy for 1000, 1500, and 2000 rpm
conditions were 96.42%, 100%, and 96.42% respectively. The results
indicate that the combined PSD-J48-FIS model has the potential for
fault diagnosis of hydraulic pumps.
Abstract: The aim of this study was to investigate ammonium
exchange capacity of natural and activated clinoptilolite from
Kwazulu-Natal Province, South Africa. X – ray fluorescence (XRF)
analysis showed that the clinoptilolite contained exchangeable ions
of sodium, potassium, calcium and magnesium. This analysis also
confirmed that the zeolite sample had a high silicon composition
compared to aluminium. Batch equilibrium studies were performed
in an orbital shaker and the data fitted the Langmuir isotherm very
well. The ammonium exchange capacity was found to increase with
pH and temperature. Clinoptilolite functionalization with
hydrochloric acid increased its ammonia uptake ability.