Abstract: The main purpose of this study is to assess the
sediment quality and potential ecological risk in marine sediments in
Gymea Bay located in south Sydney, Australia. A total of 32 surface
sediment samples were collected from the bay. Current track
trajectories and velocities have also been measured in the bay. The
resultant trace elements were compared with the adverse biological
effect values Effect Range Low (ERL) and Effect Range Median
(ERM) classifications. The results indicate that the average values of
chromium, arsenic, copper, zinc, and lead in surface sediments all
reveal low pollution levels and are below ERL and ERM values. The
highest concentrations of trace elements were found close to
discharge points and in the inner bay, and were linked with high
percentages of clay minerals, pyrite and organic matter, which can
play a significant role in trapping and accumulating these elements.
The lowest concentrations of trace elements were found to be on the
shoreline of the bay, which contained high percentages of sand
fractions. It is postulated that the fine particles and trace elements are
disturbed by currents and tides, then transported and deposited in
deeper areas. The current track velocities recorded in Gymea Bay had
the capability to transport fine particles and trace element pollution
within the bay. As a result, hydrodynamic measurements were able to
provide useful information and to help explain the distribution of
sedimentary particles and geochemical properties. This may lead to
knowledge transfer to other bay systems, including those in remote
areas. These activities can be conducted at a low cost, and are
therefore also transferrable to developing countries. The advent of
portable instruments to measure trace elements in the field has also
contributed to the development of these lower cost and easily applied
methodologies available for use in remote locations and low-cost
economies.
Abstract: Large quantities of solid wastes being generated
worldwide from sources such as household, domestic, industrial,
commercial and construction demolition activities, leads to
environmental concerns. Utilization of these wastes in making
building construction materials can reduce the magnitude of the
associated problems. When these waste products are used in place of
other conventional materials, natural resources and energy are
preserved and expensive and/or potentially harmful waste disposal is
avoided. Recycling which is regarded as the third most preferred waste
disposal option, with its numerous environmental benefits, stand as a
viable option to offset the environmental impact associated with the
construction industry. This paper reviews the results of laboratory tests and important
research findings, and the potential of using these wastes in building
construction materials with focus on sustainable development.
Research gaps, which includes; the need to develop standard mix
design for solid waste based building materials; the need to develop
energy efficient method of processing solid waste use in concrete; the
need to study the actual behavior or performance of such building
materials in practical application and the limited real life application
of such building materials have also been identified. A research is being proposed to develop an environmentally
friendly, lightweight building block from recycled waste paper,
without the use of cement, and with properties suitable for use as
walling unit. This proposed research intends to incorporate,
laboratory experimentation and modeling to address the identified
research gaps.
Abstract: Microcantilevers are the basic MEMS devices, which
can be used as sensors, actuators and electronics can be easily built
into them. The detection principle of microcantilever sensors is based
on the measurement of change in cantilever deflection or change in its
resonance frequency. The objective of this work is to explore the
analogies between mechanical and electrical equivalent of
microcantilever beams. Normally scientists and engineers working in
MEMS use expensive software like CoventorWare, IntelliSuite,
ANSYS/Multiphysics etc. This paper indicates the need of developing
electrical equivalent of the MEMS structure and with that, one can
have a better insight on important parameters, and their interrelation of
the MEMS structure. In this work, considering the mechanical model
of microcantilever, equivalent electrical circuit is drawn and using
force-voltage analogy, it is analyzed with circuit simulation software.
By doing so, one can gain access to powerful set of intellectual tools
that have been developed for understanding electrical circuits Later
the analysis is performed using ANSYS/Multiphysics - software based
on finite element method (FEM). It is observed that both mechanical
and electrical domain results for a rectangular microcantlevers are in
agreement with each other.
Abstract: Software quality issues require special attention
especially in view of the demands of quality software product to meet
customer satisfaction. Software development projects in most
organisations need proper defect management process in order to
produce high quality software product and reduce the number of
defects. The research question of this study is how to produce high
quality software and reducing the number of defects. Therefore, the
objective of this paper is to provide a framework for managing
software defects by following defined life cycle processes. The
methodology starts by reviewing defects, defect models, best
practices, and standards. A framework for defect management life
cycle is proposed. The major contribution of this study is to define a
defect management roadmap in software development. The adoption
of an effective defect management process helps to achieve the
ultimate goal of producing high quality software products and
contributes towards continuous software process improvement.
Abstract: Geopolymer composites reinforced with flax fabrics
and nanoclay are fabricated and studied for physical and mechanical
properties using X-Ray Diffraction (XRD), Fourier Transform
Infrared Spectroscopy (FTIR), and Scanning Electron Microscope
(SEM). Nanoclay platelets at a weight of 1.0%, 2.0%, and 3.0% were
added to geopolymer pastes. Nanoclay at 2.0 wt.% was found to
improve density and decrease porosity while improving flexural
strength and post-peak toughness. A microstructural analysis
indicated that nanoclay behaves as filler and as an activator
supporting geopolymeric reaction while producing a higher content
geopolymer gel improving the microstructure of binders. The process
enhances adhesion between the geopolymer matrix and flax fibres.
Abstract: Both steady and unsteady turbulent mixed convection
heat transfer in a 3D lid-driven enclosure, which has constant heat
flux on the middle of bottom wall and with isothermal moving
sidewalls, is reported in this paper for working fluid with Prandtl
number Pr = 0.71. The other walls are adiabatic and stationary. The
dimensionless parameters used in this research are Reynolds number,
Re = 5000, 10000 and 15000, and Richardson number, Ri = 1 and 10.
The simulations have been done by using different turbulent methods
such as RANS, URANS, and LES. The effects of using different k-ε
models such as standard, RNG and Realizable k-ε model are
investigated. Interesting behaviours of the thermal and flow fields
with changing the Re or Ri numbers are observed. Isotherm and
turbulent kinetic energy distributions and variation of local Nusselt
number at the hot bottom wall are studied as well. The local Nusselt
number is found increasing with increasing either Re or Ri number.
In addition, the turbulent kinetic energy is discernibly affected by
increasing Re number. Moreover, the LES results have shown good
ability of this method in predicting more detailed flow structures in
the cavity.
Abstract: In this study, the effects and interactions of reaction
time and capping agent assistance during sol-gel synthesis of
magnesium substituted hydroxyapatite nanopowder (MgHA) on
hydroxyapatite (HA) to β-tricalcium phosphate (β-TCP) ratio, Ca/P
ratio and mean crystallite size was examined experimentally as well
as through statistical analysis. MgHA nanopowders were synthesized
by sol-gel technique at room temperature using aqueous solution of
calcium nitrate tetrahydrate, magnesium nitrate hexahydrate and
potassium dihydrogen phosphate as starting materials. The reaction
time for sol-gel synthesis was varied between 15 to 60 minutes. Two
process routes were followed with and without addition of
triethanolamine (TEA) in the solutions. The elemental compositions
of as-synthesized powders were determined using X-ray fluorescence
(XRF) spectroscopy. The functional groups present in the assynthesized
MgHA nanopowders were established through Fourier
Transform Infrared Spectroscopy (FTIR). The amounts of phases
present, Ca/P ratio and mean crystallite sizes of MgHA nanopowders
were determined using X-ray diffraction (XRD). The HA content in
biphasic mixture of HA and β-TCP and Ca/P ratio in as-synthesized
MgHA nanopowders increased effectively with reaction time of sols
(p0.15, two way ANOVA). The MgHA nanopowders
synthesized with TEA assistance exhibited 14 nm lower crystallite
size (p
Abstract: In the past years electric mobility became part of a
public discussion. The trend to fully electrified vehicles instead of
vehicles fueled with fossil energy has notably gained momentum.
Today nearly every big car manufacturer produces and sells fully
electrified vehicles, but electrified vehicles are still not as competitive
as conventional powered vehicles. As the traction battery states the
largest cost driver, lowering its price is a crucial objective. In
addition to improvements in product and production processes a nonnegligible,
but widely underestimated cost driver of production can
be found in logistics, since the production technology is not
continuous yet and neither are the logistics systems. This paper presents an approach to evaluate cost factors on
different designs of load carrier systems. Due to numerous
interdependencies, the combination of costs factors for a particular
scenario is not transparent. This is effecting actions for cost reduction
negatively, but still cost reduction is one of the major goals for
simultaneous engineering processes. Therefore a concurrent and
phase appropriate cost valuation method is necessary to serve cost
transparency. In this paper the four phases of this cost valuation
method are defined and explained, which based upon a new approach
integrating the logistics development process in to the integrated
product and process development.
Abstract: One of the global combinatorial optimization
problems in machine learning is feature selection. It concerned with
removing the irrelevant, noisy, and redundant data, along with
keeping the original meaning of the original data. Attribute reduction
in rough set theory is an important feature selection method. Since
attribute reduction is an NP-hard problem, it is necessary to
investigate fast and effective approximate algorithms. In this paper,
we proposed two feature selection mechanisms based on memetic
algorithms (MAs) which combine the genetic algorithm with a fuzzy
record to record travel algorithm and a fuzzy controlled great deluge
algorithm, to identify a good balance between local search and
genetic search. In order to verify the proposed approaches, numerical
experiments are carried out on thirteen datasets. The results show that
the MAs approaches are efficient in solving attribute reduction
problems when compared with other meta-heuristic approaches.
Abstract: Response Surface Methods (RSM) provide
statistically validated predictive models that can then be manipulated
for finding optimal process configurations. Variation transmitted to
responses from poorly controlled process factors can be accounted
for by the mathematical technique of propagation of error (POE),
which facilitates ‘finding the flats’ on the surfaces generated by
RSM. The dual response approach to RSM captures the standard
deviation of the output as well as the average. It accounts for
unknown sources of variation. Dual response plus propagation of
error (POE) provides a more useful model of overall response
variation. In our case, we implemented this technique in predicting
compressive strength of concrete of 28 days in age. Since 28 days is
quite time consuming, while it is important to ensure the quality
control process. This paper investigates the potential of using design
of experiments (DOE-RSM) to predict the compressive strength of
concrete at 28th day. Data used for this study was carried out from
experiment schemes at university of Benghazi, civil engineering
department. A total of 114 sets of data were implemented. ACI mix
design method was utilized for the mix design. No admixtures were
used, only the main concrete mix constituents such as cement, coarseaggregate,
fine aggregate and water were utilized in all mixes.
Different mix proportions of the ingredients and different water
cement ratio were used. The proposed mathematical models are
capable of predicting the required concrete compressive strength of
concrete from early ages.
Abstract: This study evaluated the acute toxicity and tissue
distribution of intravenously administered gold nanoparticles
(AuNPs) in male rabbits. Rabbits were exposed to single dose of
AuNPs (300 μg/ kg). Toxic effects were assessed via general
behavior, hematological parameters, serum biochemical parameters,
and histopathological examination of various rabbits’ organs.
Inductively coupled plasma–mass spectrometry (ICP-MS) was used
to determine gold concentrations in tissue samples collected at
predetermined time intervals. After one week, AuNPs exerted no
obvious acute toxicity in rabbits. However, inflammatory reactions
were observed in liver, lungs and kidneys accompanied with mild
absolute neutrophilia and significant monocytosis. The highest gold
levels were found in the spleen and liver followed by lungs, and
kidneys. These results indicated that AuNPs could be distributed
extensively to various tissues in the body, but primarily in the spleen
and liver.
Abstract: With the introduction of cash-less society policy by
the Central Bank of Nigeria, the concept of e-banking services have
over the years’ experience a significant improvement. Today quite a
number of people are embracing e-banking activities especially
ATM, thereby moving away from the conventional banking system.
This paper presents a review of the underlying Architectural Layout
of Intra-Bank and Inter-Bank ATM connectivity in Nigeria. The
paper further investigates and discusses factors affecting the Intra-
Bank and Inter-Bank ATM connectivity in Nigeria. In addition, as
well possible solutions to these factors affecting ATM Connectivity
and Operations are proposed.
Abstract: In 2009, the new HRM policy was implemented in
Qatar for public sector organisations. The purpose of this research is
to examine how Qatar’s 2009 HRM policy was significant in
influencing employee retention in public organisations. The
conducted study utilised quantitative methodology to analyse the data
on employees’ perceptions of such HRM practices as Performance
Management, Rewards and Promotion, Training and Development
associated with the HRM policy in public organisations in
comparison to semi-private organisations. Employees of seven public
and semi-private organisations filled in the questionnaire based on
the 5-point Likert scale to present quantitative results. The data was
analysed with the correlation and multiple regression statistical
analyses. It was found that Performance Management had the
relationship with Employee Retention, and Rewards and Promotion
influenced Job Satisfaction in public organisations. Relationship
between Job Satisfaction and Employee Retention was also observed.
However, no significant differences were observed in the role of
HRM practices in public and semi-private organisations.
Abstract: Prosecution of sexual violence in international
criminal law requires not only an understanding of the mechanisms
employed to prosecute sexual violence but also a critical analysis of
the factors facilitating perpetuation of such crimes in armed conflicts.
The extrapolations laid out in this essay delve into the jurisprudence
of international criminal law pertaining to sexual and gender based
violence followed by the core question of this essay – has the
entrenchment of sexual violence as international crimes in the Rome
Statute been successful to address such violence in armed conflicts?
Abstract: The purposes of this research are to make comparisons in
respect of the behaviors on the use of the services of metered taxi
classified by the demographic factor and to study the influence of the
recognition on service quality having the effect on usage behaviors of
metered taxi services of consumers in Bangkok Metropolitan Areas. The
samples used in this research were 400 metered taxi service users in
Bangkok Metropolitan Areas and questionnaire was used as the tool for
collecting the data. Analysis statistics are mean and multiple regression
analysis. Results of the research revealed that the consumers recognize the
overall quality of services in each aspect include tangible aspects of the
service, responses to customers, assurance on the confidence,
understanding and knowing of customers which is rated at the moderate
level except the aspect of the assurance on the confidence and
trustworthiness which are rated at a high level. For the result of
hypothetical test, it is found that the quality in providing the services on
the aspect of the assurance given to the customers has the effect on the
usage behaviors of metered taxi services and the aspect of the frequency
on the use of the services per month which in this connection. Such
variable can forecast at one point nine percent (1.9%). In addition, quality
in providing the services and the aspect of the responses to customers
have the effect on the behaviors on the use of metered taxi services on the
aspect of the expenses on the use of services per month which in this
connection, such variable can forecast at two point one percent (2.1%).
Abstract: This paper presents the results of a study on the
influence of varying percentages of rock bridges along a basal surface
defining a biplanar failure mode. A pseudo-coupled-hydromechanical
brittle fracture analysis is adopted using the state-of-the-art code
Slope Model. Model results show that rock bridge failure is strongly
influenced by the incorporation of groundwater pressures. The
models show that groundwater pressure can promote total failure of a
5% rock bridge along the basal surface. Once the percentage of the
rock bridges increases to 10 and 15%, although, the rock bridges are
broken, full interconnection of the surface defining the basal surface
of the biplanar mode does not occur. Increased damage is caused
when the rock bridge is located at the daylighting end of the basal
surface in proximity to the blast damage zone. As expected, some
cracking damage is experienced in the blast damage zone, where
properties representing a good quality controlled damage blast
technique were assumed. Model results indicate the potential increase
of permeability towards the blast damage zone.
Abstract: Laura Island, which is located about 50 km away from
downtown, is a source of water supply in Majuro atoll, which is the
capital of the Republic of the Marshall Islands. Low and flat Majuro
atoll has neither river nor lake. It is very important for Majuro atoll to
ensure the conservation of its water resources. However, upconing,
which is the process of partial rising of the freshwater-saltwater
boundary near the water-supply well, was caused by the excess
pumping from it during the severe drought in 1998. Upconing will
make the water usage of the freshwater lens difficult. Thus,
appropriate water usage is required to prevent up coning in the
freshwater lens because there is no other water source during drought. Numerical simulation of water usage applying SEAWAT model
was conducted at the central part of Laura Island, including the water
supply well, which was affected by upconing. The freshwater lens was
created as a result of infiltration of consistent average rainfall. The lens
shape was almost the same as the one in 1985. 0 of monthly rainfall
and variable daily pump discharge were used to calculate the
sustainable pump discharge from the water supply well. Consequently,
the total amount of pump discharge was increased as the daily pump
discharge was increased, indicating that it needs more time to recover
from upconing. Thus, a pump standard to reduce the pump intensity is
being proposed, which is based on numerical simulation concerning
the occurrence of the up-coning phenomenon in Laura Island during
the drought.
Abstract: This study investigates how the site specific traffic
data differs from the Mechanistic Empirical Pavement Design
Software default values. Two Weigh-in-Motion (WIM) stations were
installed in Interstate-40 (I-40) and Interstate-25 (I-25) to developed
site specific data. A computer program named WIM Data Analysis
Software (WIMDAS) was developed using Microsoft C-Sharp (.Net)
for quality checking and processing of raw WIM data. A complete
year data from November 2013 to October 2014 was analyzed using
the developed WIM Data Analysis Program. After that, the vehicle
class distribution, directional distribution, lane distribution, monthly
adjustment factor, hourly distribution, axle load spectra, average
number of axle per vehicle, axle spacing, lateral wander distribution,
and wheelbase distribution were calculated. Then a comparative
study was done between measured data and AASHTOWare default
values. It was found that the measured general traffic inputs for I-40
and I-25 significantly differ from the default values.
Abstract: The end panels of a large rectangular industrial duct,
which experience significant internal pressures, also experience
considerable transverse shear due to transfer of gravity loads to the
supports. The current design practice of such thin plate panels for
shear load is based on methods used for the design of plate girder
webs. The structural arrangements, the loadings and the resulting
behavior associated with the industrial duct end panels are, however,
significantly different from those of the web of a plate girder. The
large aspect ratio of the end panels gives rise to multiple bands of
tension fields, whereas the plate girder web design is based on one
tension field. In addition to shear, the industrial end panels are
subjected to internal pressure which in turn produces significant
membrane action. This paper reports a study which was undertaken
to review the current industrial analysis and design methods and to
propose a comprehensive method of designing industrial duct end
panels for shear resistance. In this investigation, a nonlinear finite element model was
developed to simulate the behavior of industrial duct end panel, along
with the associated edge stiffeners, subjected to transverse shear and
internal pressures. The model considered the geometric imperfections
and constitutive relations for steels. Six scale independent
dimensionless parameters that govern the behavior of such end panel
were identified and were then used in a parametric study. It was
concluded that the plate slenderness dominates the shear strength of
stockier end panels, and whereas, both the plate slenderness and the
aspect ratio influence the shear strength of slender end panels. Based
on these studies, this paper proposes design aids for estimating the
shear strength of rectangular duct end panels.
Abstract: The Haussmannization plan of Cairo in 1867 formed a
regular network of roundabout spaces, though deteriorated at present.
The method of identifying the spatial structure of roundabout Cairo
for conservation matches the voronoi diagram with the space syntax
through their geometrical property of spatial convexity. In this
initiative, the primary convex hull of first-order voronoi adopts the
integral and control measurements of space syntax on Cairo’s
roundabout generators. The functional essence of royal palaces
optimizes the roundabout structure in terms of spatial measurements
and the symbolic voronoi projection of 'Tahrir Roundabout' over the
Giza Nile and Pyramids. Some roundabouts of major public and
commercial landmarks surround the pole of 'Ezbekia Garden' with a
higher control than integral measurements, which filter the new
spatial structure from the adjacent traditional town. Nevertheless, the
least integral and control measures correspond to the voronoi
contents of pollutant workshops and the plateau of old Cairo Citadel
with the visual compensation of new royal landmarks on top.
Meanwhile, the extended suburbs of infinite voronoi polygons
arrange high control generators of chateaux housing in 'garden city'
environs. The point pattern of roundabouts determines the
geometrical characteristics of voronoi polygons. The measured
lengths of voronoi edges alternate between the zoned short range at
the new poles of Cairo and the distributed structure of longer range.
Nevertheless, the shortest range of generator-vertex geometry
concentrates at 'Ezbekia Garden' where the crossways of vast Cairo
intersect, which maximizes the variety of choice at different spatial
resolutions. However, the symbolic 'Hippodrome' which is the largest
public landmark forms exclusive geometrical measurements, while
structuring a most integrative roundabout to parallel the royal syntax.
Overview of the symbolic convex hull of voronoi with space syntax
interconnects Parisian Cairo with the spatial chronology of scattered
monuments to conceive one universal Cairo structure. Accordingly,
the approached methodology of 'voronoi-syntax' prospects the future
conservation of roundabout Cairo at the inferred city-level concept.