Abstract: A novel undecimated wavelet transform based contrast enhancement algorithmis proposed to for both gray scale andcolor images. Contrast enhancement is realized by tuning the magnitude of approximation coefficients at each level with respect to the approximation coefficients of one higher level during the inverse transform phase in a center/surround enhancement sense.The performance of the proposed algorithm is evaluated using a statistical visual contrast measure (VCM). Experimental results on the proposed algorithm show improvement in terms of the VCM.
Abstract: We present the design of Analog front end (AFE) low noise pre-amplifier implemented in a high voltage 0.18-µm CMOS technology for a three dimensional ultrasound bio microscope (3D UBM) application. The fabricated chip has 4X16 pre-amplifiers implemented to interface a 2-D array of high frequency capacitive micro-machined ultrasound transducers (CMUT). Core AFE cell consists of a high-voltage pulser in the transmit path, and a low-noise transimpedance amplifier in the receive path. Proposed system offers a high image resolution by the use of high frequency CMUTs with associated high performance imaging electronics integrated together. Performance requirements and the design methods of the high bandwidth transimpedance amplifier are described in the paper. A single cell of transimpedance (TIA) amplifier and the bias circuit occupies a silicon area of 250X380 µm2 and the full chip occupies a total silicon area of 10x6.8 mm².
Abstract: The effect of nonthermal pulsed electric field (PEF) and thermal treatment (90⁰C for 60s) was studied on quality parameters of emblica officinalis juice for the period of 6 weeks at 4⁰C using monopolar rectangular pulse of 1µs width. The PEF treatment was given using static chamber at 24kV/cm for 500µs. The quality of emblica officinalis juice was investigated in terms of non enzymatic browning index (NEBI), 5-hydroxymethyl-2-furfural (HMF), total polyphenol content and antioxidant capacity. ⁰Brix, pH and conductivity were evaluated as physical parameters. The aim of the work was to investigate the effect of PEF on the retention of bioactive compounds and retardation of browning activity. The results showed that conventional thermal treatment had led to a significant (p < 0.05) decrease of 48.15% in polyphenol content (129.56 mg of GAE L-1), with higher NEBI and HMF formation (p < 0.05) whilst PEF suppressed NEBI and retained higher polyphenol compounds (168.59 mg GAE L-1) with limiting the loss to 32.56% along maximum free radical scavenging activity (92.07%). However, pH, ⁰brix and electrical conductivity of treated juice samples remain unaffected. Therefore, PEF can be considered as an effective nonthermal treatment for retaining bioactive compounds along suppressing browning of emblica juice.
Abstract: This paper presents CMOS Current Mode Logic (CML) circuits for a high speed Digital to Analog Converter (DAC) using standard CMOS 65nm process. The CML circuits have the propagation delay advantage over its conventional CMOS counterparts due to smaller output voltage swing and tunable bias current. The CML circuits proposed in this paper can achieve a maximum propagation delay of only 9.3ps, which can satisfy the stringent requirement for the 5 GHz high speed DAC application. Another advantage for CML circuits is its dynamic symmetry characteristic resulting in a reduction of an additional inverter. Simulation results show that the proposed CML circuits can operate from 1.08V to 1.3V with temperature ranging from -40 to +120°C.
Abstract: Silicon photonics has generated an increasing interest in recent years mainly for optical communications optical interconnects in microelectronic circuits or bio-sensing applications. The development of elementary passive and active components (including detectors and modulators), which are mainly fabricated on the silicon on insulator platform for CMOS-compatible fabrication, has reached such a performance level that the integration challenge of silicon photonics with microelectronic circuits should be addressed. Since crystalline silicon can only be grown from another silicon crystal, making it impossible to deposit in this state, the optical devices are typically limited to a single layer. An alternative approach is to integrate a photonic layer above the CMOS chip using back-end CMOS fabrication process. In this paper, various materials, including silicon nitride, amorphous silicon, and polycrystalline silicon, for this purpose are addressed.
Abstract: Silicon photonics is merging as a unified platform for driving photonic based telecommunications and for local photonic based interconnect but it suffers from large footprint as compared with the nanoelectronics. Plasmonics is an attractive alternative for nanophotonics. In this work, two CMOS compatible plasmonic waveguide platforms are compared. One is the horizontal metal-insulator-Si-insulator-metal nanoplasmonic waveguide and the other is metal-insulator-Si hybrid plasmonic waveguide. Various passive and active photonic devices have been experimentally demonstrated based on these two plasmonic waveguide platforms.
Abstract: This paper presents a 14-bit cyclic-pipelined Analog to digital converter (ADC) running at 1 MS/s. The architecture is based on a 1.5-bit per stage structure utilizing digital correction for each stage. The ADC consists of two 1.5-bit stages, one shift register delay line, and digital error correction logic. Inside each 1.5-bit stage, there is one gain-boosting op-amp and two comparators. The ADC was implemented in 0.18µm CMOS process and the design has an area of approximately 0.2 mm2. The ADC has a differential input range of 1.2 Vpp. The circuit has an average power consumption of 3.5mA with 10MHz sampling clocks. The post-layout simulations of the design satisfy 12-bit SNDR with a full-scale sinusoid input.
Abstract: In this paper, the design of wide-swing constant transconductance (gm) bias circuit that generates bias voltage for low-noise amplifier (LNA) circuit design by using an off-chip resistor is demonstrated. The overall transconductance (Gm) generated by the constant gm bias circuit is important to maintain the overall gain and noise figure of the LNA circuit. Therefore, investigation is performed to study the variation in Gm with process, temperature and supply voltage (PVT). Temperature and supply voltage are swept from -10 °C to 85 °C and 1.425 V to 1.575 V respectively, while the process conditions are also varied to the extreme and the gm variation is eventually concluded at between -3 % to 7 %. With the slight variation in the gm value, through simulation, at worst condition of state SS, we are able to attain a conversion gain (S21) variation of -3.10 % and a noise figure (NF) variation of 18.71 %. The whole constant gm circuit draws approximately 100 µA from a 1.5V supply and is designed based on 0.13 µm CMOS process.
Abstract: The objective of this study is to investigate the performance of the electrocoagulation process for color and COD removal in palm oil wastewater using a 10 L batch reactor. Iron was used as electrodes and the distance between electrodes was 2 cm. The effects of operating parameters: current voltage (6, 12 and 18 volt), reaction time (5, 15, 30, 45 and 60 min) and initial pH (4 and 9) of treatment efficiency were examine. The result showed that decolorization and COD removal efficiency increased with the increase in current voltage and reaction time. The proper condition for decolorization achieved at initial pH 4 and 9 were current voltage of 12 volt, reaction time 30 min. The decolorization efficiency reached 90.4% and 88.9%, respectively. COD removal was achiveved at current voltage 12 volt, reaction time 15 min. COD removal efficiency was 89.2 % and 83.0%, respectively. From the results, to show electrocoagulation process can treat palm oil mill wastewater in both acidic and basic condition at high efficiency for color and COD removal. Consequently, electrocoagulation process can be used or applied as a post-treatment step to improve the quality of the final discharge in term of color and residual COD removal.
Abstract: A silicon photomultiplier (SiPM) was designed, fabricated and characterized. The SiPM was based on SACM (Separation of Absorption, Charge and Multiplication) structure, which was optimized for blue light detection in application of positron emission tomography (PET). The achieved SiPM array has a high geometric fill factor of 64% and a low breakdown voltage of about 22V, while the temperature dependence of breakdown voltage is only 17mV/°C. The gain and photon detection efficiency of the device achieved were also measured under illumination of light at 405nm and 460nm wavelengths. The gain of the device is in the order of 106. The photon detection efficiency up to 60% has been observed under 1.8V overvoltage.
Abstract: This paper presents the design and implementation of a fully integrated Capacitance-to-Voltage Converter (CVC) as the analog front-end for magnetometer interface IC. The application demands very low power solution operating in the frequency of around 20 KHz. The design adapts low power architecture to create low noise electronic interface for Capacitive Micro-machined Lorentz force magnetometer sensor. Using a 0.18-μm CMOS process, simulation results of this interface IC show that the proposed CVC can provide 33 dB closed loop gain, 20 nV/√Hz input referred noise at 20 KHz, while consuming 65 μA current from 1.8-V supply.
Abstract: Intercalation imparts interesting features to the host graphite material. Two different types of intercalated compounds called (GIC-bisulphate or Nyex 1000 and GIC-nitrate or Nyex 3000) were tested for their adsorption capacity and ability to undergo electrochemical regeneration. It was found that Nyex 3000 showed comparatively slow kinetics along with reduced adsorption capacity to one half for acid violet 17 as adsorbate. Acid violet 17 was selected as model organic pollutant for evaluating comparative performance of said adsorbents. Both adsorbent materials showed 100% regeneration efficiency as achieved by passing a charge of 36 C g-1 at a current density of 12 mA cm-2 and a treatment time of 60 min.
Abstract: The problem of optimal planning of multiple sources
of distributed generation (DG) in distribution networks is treated in
this paper using an improved Ant Colony Optimization algorithm
(ACO). This objective of this problem is to determine the DG
optimal size and location that in order to minimize the network real
power losses. Considering the multiple sources of DG, both size and
location are simultaneously optimized in a single run of the proposed
ACO algorithm. The various practical constraints of the problem are
taken into consideration by the problem formulation and the
algorithm implementation. A radial power flow algorithm for
distribution networks is adopted and applied to satisfy these
constraints. To validate the proposed technique and demonstrate its
effectiveness, the well-know 69-bus feeder standard test system is
employed.cm.
Abstract: For the improvement of the ability in detecting
small calcifications using Ultrasonography (US) we propose a
novel indicator of calcifications in an ultrasound B-mode image
without decrease in frame rate. Since the waveform of an
ultrasound pulse changes at a calcification position, the
decorrelation of adjacent scan lines occurs behind a
calcification. Therefore, we employ the decorrelation of
adjacent scan lines as an indicator of a calcification. The
proposed indicator depicted wires 0.05 mm in diameter at 2 cm
depth with a sensitivity of 86.7% and a specificity of 100%,
which were hardly detected in ultrasound B-mode images. This
study shows the potential of the proposed indicator to
approximate the detectable calcification size using an US
device to that of an X-ray imager, implying the possibility that
an US device will become a convenient, safe, and principal
clinical tool for the screening of breast cancer.
Abstract: The goal of this paper is to examine the effects of laser
radiation on the skin wound healing using infrared thermography as
non-invasive method for the monitoring of the skin temperature
changes during laser treatment. Thirty Wistar rats were used in this
study. A skin lesion was performed at the leg on all rats. The animals
were exposed to laser radiation (λ = 670 nm, P = 15 mW, DP = 16.31
mW/cm2) for 600 s. Thermal images of wound were acquired before
and after laser irradiation. The results have demonstrated that the
tissue temperature decreases from 35.5±0.50°C in the first treatment
day to 31.3±0.42°C after the third treatment day. This value is close
to the normal value of the skin temperature and indicates the end of
the skin repair process. In conclusion, the improvements in the
wound healing following exposure to laser radiation have been
revealed by infrared thermography.
Abstract: The objective of this project is to study the corrosion
behaviour and hardness based on the presence of martensite in dual
phase steel. This study was conducted on six samples of dual phase
steel which have different percentage of martensite. A total of 9
specimens were prepared by intercritical annealing process to study
the effect of temperature to the formation of martensite. The low
carbon steels specimens were heated for 25 minutes in a specified
temperature ranging from 7250C to 8250C followed by rapid cooling
in water. The measurement of corrosion rate was done by using
extrapolation tafel method, while potentiostat was used to control and
measured the current produced. This measurement is performed
through a system named CMS105. The result shows that a specimen
with higher percentage of martensite is likely to corrode faster.
Hardness test for each specimen was conducted to compare its
hardness with low carbon steel. The results obtained indicate that the
specimen hardness is proportional to the amount of martensite in dual
phase steel.
Abstract: Jatropha curcas stem was analyzed for chemical
compositions: 19.11% pentosan, 42.99% alphacellulose and 24.11%
lignin based on dry weight of 100-g raw material. The condition to
fractionate cellulose, hemicellulose and lignin in J. curcas stem using
steam explosion was optimized. The procedure started from cutting J.
curcas stem into small pieces and soaked in water for overnight.
After that, they were steam exploded at 214 °C and 21 kg/cm2 for 5
min. The obtained hydrolysate contained 1.55 g/L ferulic acid which
after that was used as substrate for vanillin production by Aspergillus
niger and Pycnoporus cinnabarinus in one-step process. The
maximum 0.65 g/L of vanillin were obtained with the conversion rate
of 45.2% based on the initial ferulic acid.
Abstract: An adaptive dynamic cerebellar model articulation
controller (DCMAC) neural network used for solving the prediction
and identification problem is proposed in this paper. The proposed
DCMAC has superior capability to the conventional cerebellar model
articulation controller (CMAC) neural network in efficient learning
mechanism, guaranteed system stability and dynamic response. The
recurrent network is embedded in the DCMAC by adding feedback
connections in the association memory space so that the DCMAC
captures the dynamic response, where the feedback units act as
memory elements. The dynamic gradient descent method is adopted to
adjust DCMAC parameters on-line. Moreover, the analytical method
based on a Lyapunov function is proposed to determine the
learning-rates of DCMAC so that the variable optimal learning-rates
are derived to achieve most rapid convergence of identifying error.
Finally, the adaptive DCMAC is applied in two computer simulations.
Simulation results show that accurate identifying response and
superior dynamic performance can be obtained because of the
powerful on-line learning capability of the proposed DCMAC.
Abstract: IP networks are evolving from data communication
infrastructure into many real-time applications such as video
conferencing, IP telephony and require stringent Quality of Service
(QoS) requirements. A rudimentary issue in QoS routing is to find a
path between a source-destination pair that satisfies two or more endto-
end constraints and termed to be NP hard or complete. In this
context, we present an algorithm Multi Constraint Path Problem
Version 3 (MCPv3), where all constraints are approximated and
return a feasible path in much quicker time. We present another
algorithm namely Delay Coerced Multi Constrained Routing
(DCMCR) where coerce one constraint and approximate the
remaining constraints. Our algorithm returns a feasible path, if exists,
in polynomial time between a source-destination pair whose first
weight satisfied by the first constraint and every other weight is
bounded by remaining constraints by a predefined approximation
factor (a). We present our experimental results with different
topologies and network conditions.
Abstract: This paper describes the design of new method of
propagation delay measurement in micro and nanostructures during
characterization of ASIC standard library cell. Providing more
accuracy timing information about library cell to the design team we
can improve a quality of timing analysis inside of ASIC design flow
process. Also, this information could be very useful for semiconductor
foundry team to make correction in technology process. By
comparison of the propagation delay in the CMOS element and result
of analog SPICE simulation. It was implemented as digital IP core for
semiconductor manufacturing process. Specialized method helps to
observe the propagation time delay in one element of the standard-cell
library with up-to picoseconds accuracy and less. Thus, the special
useful solutions for VLSI schematic to parameters extraction, basic
cell layout verification, design simulation and verification are
announced.