Abstract: In this study, aerobic digestion of tannery industry
wastewater was carried out using mixed culture obtained from
common effluent treatment plant treating tannery wastewater. The
effect of pH, temperature, inoculum concentration, agitation speed
and initial substrate concentration on the reduction of organic matters
were found. The optimum conditions for COD reduction was found
to be pH - 7 (60%), temperature - 30ÔùªC (61%), inoculum
concentration - 2% (61%), agitation speed - 150rpm (65%) and initial
substrate concentration - 1560 mg COD/L (74%). Kinetics studies
were carried by using Monod model, First order, Diffusional model
and Singh model. From the results it was found that the Monod
model suits well for the degradation of tannery wastewater using
mixed microbial consortium.
Abstract: Nowadays, the increase of human population every
year results in increasing of water usage and demand. Saen Saep
canal is important canal in Bangkok. The main objective of this study
is using Artificial Neural Network (ANN) model to estimate the
Chemical Oxygen Demand (COD) on data from 11 sampling sites.
The data is obtained from the Department of Drainage and Sewerage,
Bangkok Metropolitan Administration, during 2007-2011. The
twelve parameters of water quality are used as the input of the
models. These water quality indices affect the COD. The
experimental results indicate that the ANN model provides a high
correlation coefficient (R=0.89).
Abstract: The photochemical and photo-Fenton oxidation of 1,3-dichloro-2-propanol was performed in a batch reactor, at room temperature, using UV radiation, H2O2 as oxidant, and Fenton-s reagent. The effect of the oxidative agent-s initial concentration was investigated as well as the effect of the initial concentration of Fe(II) by following the target compound degradation, the total organic carbon removal and the chloride ion production. Also, from the kinetic analysis conducted and proposed reaction scheme it was deduced that the addition of Fe(II) significantly increases the production and the further oxidation of the chlorinated intermediates.
Abstract: Agricultural residue such as oil palm fronds (OPF) is
cheap, widespread and available throughout the year. Hemicelluloses
extracted from OPF can be hydrolyzed to their monomers and used in
production of xylooligosaccharides (XOs). The objective of the
present study was to optimize the enzymatic hydrolysis process of
OPF hemicellulose by varying pH, temperature, enzyme and substrate
concentration for production of XOs. Hemicelluloses was extracted
from OPF by using 3 M potassium hydroxide (KOH) at temperature of
40°C for 4 hrs and stirred at 400 rpm. The hemicellulose was then
hydrolyzed using Trichoderma longibrachiatum xylanase at different
pH, temperature, enzyme and substrate concentration. XOs were
characterized based on reducing sugar determination. The optimum
conditions to produced XOs from OPF hemicellulose was obtained at
pH 4.6, temperature of 40°C , enzyme concentration of 2 U/mL and
2% substrate concentration. The results established the suitability of
oil palm fronds as raw material for production of XOs.
Abstract: Droplet size distributions in the cold spray of a fuel
are important in observed combustion behavior. Specification of
droplet size and velocity distributions in the immediate downstream
of injectors is also essential as boundary conditions for advanced
computational fluid dynamics (CFD) and two-phase spray transport
calculations. This paper describes the development of a new model to
be incorporated into maximum entropy principle (MEP) formalism
for prediction of droplet size distribution in droplet formation region.
The MEP approach can predict the most likely droplet size and
velocity distributions under a set of constraints expressing the
available information related to the distribution.
In this article, by considering the mechanisms of turbulence
generation inside the nozzle and wave growth on jet surface, it is
attempted to provide a logical framework coupling the flow inside the
nozzle to the resulting atomization process. The purpose of this paper
is to describe the formulation of this new model and to incorporate it
into the maximum entropy principle (MEP) by coupling sub-models
together using source terms of momentum and energy. Comparison
between the model prediction and experimental data for a gas turbine
swirling nozzle and an annular spray indicate good agreement
between model and experiment.
Abstract: In this paper, naturally immobilized lipase, Carica
papaya lipase, catalyzed biodiesel production from fish oil was
studied. The refined fish oil, extracted from the discarded parts of
fish, was used as a starting material for biodiesel production. The
effects of molar ratio of oil: methanol, lipase dosage, initial water
activity of lipase, temperature and solvent were investigated. It was
found that Carica papaya lipase was suitable for methanolysis of fish
oil to produce methyl ester. The maximum yield of methyl ester
could reach up to 83% with the optimal reaction conditions: oil:
methanol molar ratio of 1: 4, 20% (based on oil) of lipase, initial
water activity of lipase at 0.23 and 20% (based on oil) of tert-butanol
at 40oC after 18 h of reaction time. There was negligible loss in
lipase activity even after repeated use for 30 cycles.
Abstract: Aggregation behavior of sodium salicylate and sodium cumene sulfonate was studied in aqueous solution at different temperature. Specific conductivity and relative viscosity were measured at different temperature to find minimum hydrotropic concentration. The thermodynamic parameters (free energy, enthalpy and entropy) were evaluated in the temperature range of 30°C-70°C. The free energy decreased with increase in temperature. The aggregation was found to be exothermic in nature and favored by positive value of entropy.
Abstract: In this study, the transesterification of palm oil with methanol for biodiesel production was studied by using CaO–ZnO as a heterogeneous base catalyst prepared by incipient-wetness impregnation (IWI) and co-precipitation (CP) methods. The reaction parameters considered were molar ratio of methanol to oil, amount of catalyst, reaction temperature, and reaction time. The optimum conditions–15:1 molar ratio of methanol to oil, a catalyst amount of 6 wt%, reaction temperature of 60 °C, and reaction time of 8 h–were observed. The effects of Ca loading, calcination temperature, and catalyst preparation on the catalytic performance were studied. The fresh and spent catalysts were characterized by several techniques, including XRD, TPR, and XRF.
Abstract: Quantitative Structure-Activity Relationship (QSAR)
approach for discovering novel more active Calanone derivative as
anti-leukemia compound has been conducted. There are 6
experimental activities of Calanone compounds against leukemia cell
L1210 that are used as material of the research. Calculation of
theoretical predictors (independent variables) was performed by
AM1 semiempirical method. The QSAR equation is determined by
Principle Component Regression (PCR) analysis, with Log IC50 as
dependent variable and the independent variables are atomic net
charges, dipole moment (μ), and coefficient partition of noctanol/
water (Log P). Three novel Calanone derivatives that
obtained by this research have higher activity against leukemia cell
L1210 than pure Calanone.
Abstract: The purpose of this study is to investigate the chemical
degradation of the organophosphorus pesticide of parathion and
carbamate insecticide of methomyl in the aqueous phase through
Fenton process. With the employment of batch Fenton process, the
degradation of the two selected pesticides at different pH, initial
concentration, humic acid concentration, and Fenton reagent dosages
was explored. The Fenton process was found effective to degrade
parathion and methomyl. The optimal dosage of Fenton reagents (i.e.,
molar concentration ratio of H2O2 to Fe2+) at pH 7 for parathion
degradation was equal to 3, which resulted in 50% removal of
parathion. Similarly, the optimal dosage for methomyl degradation
was 1, resulting in 80% removal of methomyl. This study also found
that the presence of humic substances has enhanced pesticide
degradation by Fenton process significantly. The mass spectroscopy
results showed that the hydroxyl free radical may attack the single
bonds with least energy of investigated pesticides to form smaller
molecules which is more easily to degrade either through
physio-chemical or bilolgical processes.
Abstract: Simultaneous Saccharification and Fermentation (SSF) of sugarcane bagasse by cellulase and Pachysolen tannophilus MTCC *1077 were investigated in the present study. Important process variables for ethanol production form pretreated bagasse were optimized using Response Surface Methodology (RSM) based on central composite design (CCD) experiments. A 23 five level CCD experiments with central and axial points was used to develop a statistical model for the optimization of process variables such as incubation temperature (25–45°) X1, pH (5.0–7.0) X2 and fermentation time (24–120 h) X3. Data obtained from RSM on ethanol production were subjected to the analysis of variance (ANOVA) and analyzed using a second order polynomial equation and contour plots were used to study the interactions among three relevant variables of the fermentation process. The fermentation experiments were carried out using an online monitored modular fermenter 2L capacity. The processing parameters setup for reaching a maximum response for ethanol production was obtained when applying the optimum values for temperature (32°C), pH (5.6) and fermentation time (110 h). Maximum ethanol concentration (3.36 g/l) was obtained from 50 g/l pretreated sugarcane bagasse at the optimized process conditions in aerobic batch fermentation. Kinetic models such as Monod, Modified Logistic model, Modified Logistic incorporated Leudeking – Piret model and Modified Logistic incorporated Modified Leudeking – Piret model have been evaluated and the constants were predicted.
Abstract: Non-uniform current distribution in polymer
electrolyte membrane fuel cells results in local over-heating,
accelerated ageing, and lower power output than expected. This
issue is very critical when fuel cell experiences water flooding. In
this work, the performance of a PEM fuel cell is investigated under
cathode flooding conditions. Two-dimensional partially flooded
GDL models based on the conservation laws and electrochemical
relations are proposed to study local current density distributions
along flow fields over a wide range of cell operating conditions.
The model results show a direct association between cathode inlet
humidity increases and that of average current density but the
system becomes more sensitive to flooding. The anode inlet
relative humidity shows a similar effect. Operating the cell at
higher temperatures would lead to higher average current densities
and the chance of system being flooded is reduced. In addition,
higher cathode stoichiometries prevent system flooding but the
average current density remains almost constant. The higher anode
stoichiometry leads to higher average current density and higher
sensitivity to cathode flooding.
Abstract: The electrokinetic flow resistance (electroviscous
effect) is predicted for steady state, pressure-driven liquid flow at
low Reynolds number in a microfluidic contraction of rectangular
cross-section. Calculations of the three dimensional flow are
performed in parallel using a finite volume numerical method. The
channel walls are assumed to carry a uniform charge density and the
liquid is taken to be a symmetric 1:1 electrolyte. Predictions are
presented for a single set of flow and electrokinetic parameters. It is
shown that the magnitude of the streaming potential gradient and the
charge density of counter-ions in the liquid is greater than that in
corresponding two-dimensional slit-like contraction geometry. The
apparent viscosity is found to be very close to the value for a
rectangular channel of uniform cross-section at the chosen Reynolds
number (Re = 0.1). It is speculated that the apparent viscosity for the
contraction geometry will increase as the Reynolds number is
reduced.
Abstract: The aim of this study was to extract sugar from
sugarcane using high electric field pulse (HELP) as a non-thermal cell permeabilization method. The result of this study showed that it
is possible to permeablize sugar cane cells using HELP at very short times (less than 10 sec.) and at room temperature. Increasing the field strength (from 0.5kV/cm to 2kV/cm) and pulse number (1 to 12) led to increasing the permeabilization of sugar cane cells. The energy
consumption during HELP treatment of sugar cane (2.4 kJ/kg) was about 100 times less compared to thermal cell disintegration at 85
Abstract: The study of non-equilibrium systems has attracted
increasing interest in recent years, mainly due to the lack of
theoretical frameworks, unlike their equilibrium counterparts.
Studying the steady state and/or simple systems is thus one of the
main interests. Hence in this work we have focused our attention on
the driven lattice gas model (DLG model) consisting of interacting
particles subject to an external field E. The dynamics of the system
are given by hopping of particles to nearby empty sites with rates
biased for jumps in the direction of E. Having used small two
dimensional systems of DLG model, the stochastic properties at nonequilibrium
steady state were analytically studied. To understand the
non-equilibrium phenomena, we have applied the analytic approach
via master equation to calculate probability function and analyze
violation of detailed balance in term of the fluctuation-dissipation
theorem. Monte Carlo simulations have been performed to validate
the analytic results.
Abstract: A simultaneous study on indoor and outdoor particulate matter concentrations was done in five elementary schools in central parts of Tehran, Iran. Three sizes of particles including PM10, PM2.5 and PM1.0 were measured in 13 classrooms within this schools during winter (January, February and March) 2009. A laserbased portable aerosol spectrometer Model Grimm-1.108, was used for the continuous measurement of particles. The average indoor concentration of PM10, PM2.5 and PM1.0 in studied schools were 274 μg/m3, 42 μg/m3 and 19 μg/m3 respectively; and average outdoor concentrations of PM10, PM2.5 and PM1.0 were evaluated to be 22 μg/m3, 38 μg/m3 and 140 μg/m3 respectively.
Abstract: In this research work, poly (acrylonitrile-butadienestyrene)/
polypropylene (ABS/PP) blends were processed by melt
compounding in a twin-screw extruder. Upgrading of the thermal
characteristics of the obtained materials was attempted by the
incorporation of organically modified montmorillonite (OMMT), as
well as, by the addition of two types of compatibilizers;
polypropylene grafted with maleic anhydride (PP-g-MAH) and ABS
grafted with maleic anhydride (ABS-g-MAH). The effect of the
above treatments was investigated separately and in combination.
Increasing the PP content in ABS matrix seems to increase the
thermal stability of their blend and the glass transition temperature
(Tg) of SAN phase of ABS. From the other part, the addition of ABS
to PP promotes the formation of its β-phase, which is maximum at 30
wt% ABS concentration, and increases the crystallization temperature
(Tc) of PP. In addition, it increases the crystallization rate of PP.The
β-phase of PP in ABS/PP blends is reduced by the addition of
compatibilizers or/and organoclay reinforcement. The incorporation
of compatibilizers increases the thermal stability of PP and reduces
its melting (ΔΗm) and crystallization (ΔΗc) enthalpies. Furthermore it
decreases slightly the Tgs of PP and SAN phases of ABS/PP blends.
Regarding the storage modulus of the ABS/PP blends, it presents a
change in their behavior at about 10°C and return to their initial
behavior at ~110°C. The incorporation of OMMT to no compatibilized
and compatibilized ABS/PP blends enhances their storage modulus.
Abstract: Nanocrystalline thin film of Na0.1V2O5.nH2O xerogel
obtained by sol gel synthesis was used as gas sensor. Gas sensing
properties of different gases such as hydrogen, petroleum and
humidity were investigated. Applying XRD and TEM the size of the
nanocrystals is found to be 7.5 nm. SEM shows a highly porous
structure with submicron meter-sized voids present throughout the
sample. FTIR measurement shows different chemical groups
identifying the obtained series of gels. The sample was n-type
semiconductor according to the thermoelectric power and electrical
conductivity. It can be seen that the sensor response curves from
130oC to 150oC show a rapid increase in sensitivity for all types of
gas injection, low response values for heating period and the rapid
high response values for cooling period. This result may suggest that
this material is able to act as gas sensor during the heating and
cooling process.
Abstract: The process parameters, temperature, pH and
substrate concentration, were optimized for the production of
gentamicin using Micromonouspora echinospora. Experiments were
carried out according to central composite design in response surface
method. The optimum conditions for the maximum production of
gentamicin were found to be: temperature – 31.7oC, pH – 6.8 and
substrate concentration – 3%. At these optimized conditions the
production of gentamicin was found to be – 1040 mg/L. The R2 value
of 0.9465 indicates a good fitness of the model.
Abstract: Synthetic juice clarification was done through spiral
wound ultrafiltration (UF) membrane module. Synthetic juice was
clarified at two different operating conditions, such as, with and
without permeates recycle at turbulent flow regime. The performance
of spiral wound ultrafiltration membrane was analyzed during
clarification of synthetic juice. Synthetic juice was the mixture of
deionized water, sucrose and pectin molecule. The operating
conditions are: feed flowrate of 10 lpm, pressure drop of 413.7 kPa
and Reynolds no of 5000. Permeate sample was analyzed in terms of
volume reduction factor (VRF), viscosity (Pa.s), ⁰Brix, TDS (mg/l),
electrical conductivity (μS) and turbidity (NTU). It was observe that
the permeate flux declined with operating time for both conditions of
with and without permeate recycle due to increase of concentration
polarization and increase of gel layer on membrane surface. For
without permeate recycle, the membrane fouling rate was faster
compared to with permeate recycle. For without permeate recycle,
the VRF rose up to 5 and for with recycle permeate the VRF is 1.9.
The VRF is higher due to adsorption of solute (pectin) molecule on
membrane surface and resulting permeateflux declined with VRF.
With permeate recycle, quality was within acceptable limit. Fouled
membrane was cleaned by applying different processes (e.g.,
deionized water, SDS and EDTA solution). Membrane cleaning was
analyzed in terms of permeability recovery.