Abstract: The novel 3D SnO cabbages self-assembled by
nanosheets were successfully synthesized via template-free
hydrothermal growth method under facile conditions. The XRD
results manifest that the as-prepared SnO is tetragonal phase. The
TEM and HRTEM results show that the cabbage nanosheets are
polycrystalline structure consisted of considerable single-crystalline
nanoparticles. Two typical Raman modes A1g=210 and Eg=112 cm-1
of SnO are observed by Raman spectroscopy. Moreover, galvanostatic
cycling tests has been performed using the SnO cabbages as anode
material of lithium ion battery and the electrochemical results suggest
that the synthesized SnO cabbage structures are a promising anode
material for lithium ion batteries.
Abstract: Sol-enhanced Zn-Ni-Al2O3 nanocomposite coatings
were electroplated on mild steel by our newly developed solenhanced
electroplating method. In this method, transparent Al2O3 sol
was added into the acidic Zn-Ni bath to produced Zn-Ni-Al2O3nanocomposite
coatings. The chemical composition, microstructure and
mechanical properties of the composite and alloy coatings deposited
at two different agitation speed were investigated. The structure of all
coatings was single γ-Ni5Zn21 phase. The composite coatings possess
refined crystals with higher microhardness compared to Zn-Ni alloy
coatings. The wear resistance of Zn-Ni coatings was improved
significantly by incorporation of alumina nano particles into the
coatings. Higher agitation speed provided more uniform coatings
with smaller grain sized and slightly higher microhardness.
Considering composite coatings, high agitation speeds may facilitate
co-deposition of alumina in the coatings.
Abstract: In the current work, a three-dimensional geometry of a
75% stenosed blood vessel is analyzed. Large eddy simulation (LES)
with the help of a dynamic subgrid scale Smagorinsky model is
applied to model the turbulent pulsatile flow. The geometry, the
transmural pressure and the properties of the blood and the elastic
boundary were based on clinical measurement data. For the flexible
wall model, a thin solid region is constructed around the 75%
stenosed blood vessel. The deformation of this solid region was
modelled as a deforming boundary to reduce the computational cost
of the solid model. Fluid-structure interaction is realized via a twoway
coupling between the blood flow modelled via LES and the
deforming vessel. The information of the flow pressure and the wall
motion was exchanged continually during the cycle by an arbitrary
Lagrangian-Eulerian method. The boundary condition of current time
step depended on previous solutions. The fluctuation of the velocity
in the post-stenotic region was analyzed in the study. The axial
velocity at normalized position Z=0.5 shows a negative value near
the vessel wall. The displacement of the elastic boundary was
concerned in this study. In particular, the wall displacement at the
systole and the diastole were compared. The negative displacement at
the stenosis indicates a collapse at the maximum velocity and the
deceleration phase.
Abstract: In general, codes and regulations consider seismic
loads only for completed structures of the bridges while, evaluation
of incomplete structure of bridges, especially those constructed by
free cantilever method, under these loads is also of great importance.
Hence, this research tried to study the behavior of incomplete
structure of common bridge type (box girder bridge), in construction
phase under vertical seismic loads. Subsequently, the paper provided
suitable guidelines and solutions to resist this destructive
phenomenon. Research results proved that use of preventive methods
can significantly reduce the stresses resulted from vertical seismic
loads in box cross sections to an acceptable range recommended by
design codes.
Abstract: This paper reports the worldwide status of building
information modeling (BIM) adoption from the perspectives of the
engagement level, the Hype Cycle model, the technology diffusion
model, and BIM services. An online survey was distributed, and 156
experts from six continents responded. Overall, North America was
the most advanced continent, followed by Oceania and Europe.
Countries in Asia perceived their phase mainly as slope of
enlightenment (mature) in the Hype Cycle model. In the technology
diffusion model, the main BIM-users worldwide were “early majority”
(third phase), but those in the Middle East/Africa and South America
were “early adopters” (second phase). In addition, the more advanced
the country, the more number of BIM services employed in general. In
summary, North America, Europe, Oceania, and Asia were advancing
rapidly toward the mature stage of BIM, whereas the Middle
East/Africa and South America were still in the early phase. The
simple indexes used in this study may be used to track the worldwide
status of BIM adoption in long-term surveys.
Abstract: This paper designs the four-phase Boost Converter
which overcomes the problem of high input ripple current and output
ripple voltage. Digital control is more convenient for such a topology
on basis of synchronization, phase shift operation, etc. Simulation
results are presented for open-loop and closed-loop for four phase
boost converter. This control scheme is applicable for PFC rectifiers
as well. Thus a comparative analysis based on the obtained results is
performed.
Abstract: This research work is concerned with the life cycle
assessment (LCA) of an expressway, as well as its infrastructure, in
Thailand. The life cycle of an expressway encompasses the raw
material acquisition phase, the construction phase, the use or service
phase, the rehabilitation phase, and finally the demolition and
disposal phase. The LCA in this research was carried out using CML
baseline 2000 and in accordance with the ISO 14040 standard. A
functional unit refers to transportation of one person over one
kilometer of a 3-lane expressway with a 50-year lifetime. This
research has revealed that the construction phase produced the largest
proportion of the environmental impact (81.46%), followed by the
service, rehabilitation, demolition and disposal phases and
transportation at 11.97%, 3.72% 0.33% and 2.52%, respectively. For
the expressway under study, the total carbon footprint over its
lifetime is equivalent to 245,639 tons CO2-eq per 1 kilometer
functional unit, with the phases of construction, service,
rehabilitation, demolition and disposal and transportation
contributing 153,690; 73,773; 3693, 755 and 13,728 tons CO2-eq,
respectively. The findings could be adopted as a benchmark against
which the environmental impacts of future similar projects can be
measured.
Abstract: Using ETABS software, this study analyzed 23
buildings to evaluate effects of mistakes during construction phase on
buildings structural behavior. For modelling, two different loadings
were assumed: 1) design loading and 2) loading due to the effects of
mistakes in construction phase. Research results determined that
considering traditional construction methods for buildings resulted in
a significant increase in dead loads and consequently intensified the
displacements and base-shears of buildings under seismic loads.
Abstract: Life Cycle Cost (LCC) is one of the goals and key
pillars of the construction management science because it comprises
many of the functions and processes necessary, which assist
organisations and agencies to achieve their goals. It has therefore
become important to design and control assets during their whole life
cycle, from the design and planning phase through to disposal phase.
LCCA is aimed to improve the decision making system in the
ownership of assets by taking into account all the cost elements
including to the asset throughout its life.
Current application of LCC approach is impractical during
misunderstanding of the advantages of LCC. This main objective of
this research is to show a different relationship between capital cost
and long-term running costs. One hundred and thirty eight actual
building projects in United Kingdom (UK) were used in order to
achieve and measure the above-mentioned objective of the study. The
result shown that LCC is one of the most significant tools should be
considered on the decision making process.
Abstract: A novel simulation method to determine the
displacements of machine tools due to thermal factors is presented.
The specific characteristic of this method is the employment of
original CAD data from the design process chain, which is
interpreted by an algorithm in terms of geometry-based allocation of
convection and radiation parameters. Furthermore analogous models
relating to the thermal behaviour of machine elements are
automatically implemented, which were gained by extensive
experimental testing with thermography imaging. With this a
transient simulation of the thermal field and in series of the
displacement of the machine tool is possible simultaneously during
the design phase. This method was implemented and is already used
industrially in the design of machining centres in order to improve
the quality of herewith manufactured workpieces.
Abstract: Copper being one of the major intrinsic residual
impurities in steel possesses the tendency to induce severe
microstructural distortions if not controlled within certain limits.
Hence, this paper investigates the effect of this element on the
mechanical properties of construction steel with a view to ascertain
its safe limits for effective control. The experiment entails collection
of statistically scheduled samples of hot rolled profiles with varied
copper concentrations in the range of 0.12-0.39 wt. %. From these
samples were prepared standard test specimens subjected to tensile,
impact, hardness and microstructural analyses. Results show a rather
huge compromise in mechanical properties as the specimens
demonstrated 54.3%, 74.2% and 64.9% reduction in tensile strength,
impact energy and hardness respectively as copper content increases
from 0.12 wt. % to 0.39 wt. %. The steel’s abysmal performance is
due to the severe distortion of the microstructure occasioned by the
development of incoherent complex compounds which weaken the
pearlite reinforcing phase. It is concluded that the presence of copper
above 0.22 wt. % is deleterious to construction steel performance.
Abstract: Three dimensional non-Interlaced carbon fibre
reinforced silicon carbide (3-D-Cf/SiC) composites with pyrocarbon
interphase were fabricated using isothermal chemical vapor
infiltration (ICVI) combined with polymer impregnation pyrolysis
(PIP) process. Polysilazane (PSZ) is used as a preceramic polymer to
obtain silicon carbide matrix. Thermo gravimetric analysis (TGA),
Infrared spectroscopic analysis (IR) and X-ray diffraction (XRD)
analysis were carried out on PSZ pyrolysed at different temperatures
to understand the pyrolysis and obtaining the optimum pyrolysing
condition to yield β-SiC phase. The density of the composites was
1.94 g cm-3 after the 3-D carbon preform was SiC infiltrated for 280 h
with one intermediate polysilazane pre-ceramic PIP process.
Mechanical properties of the composite materials were investigated
under tensile, flexural, shear and impact loading. The values of
tensile strength were 200 MPa at room temperature (RT) and 195
MPa at 500°C in air. The average RT flexural strength was 243 MPa.
The lower flexural strength of these composites is because of the
porosity. The fracture toughness obtained from single edge notched
beam (SENB) technique was 39 MPa.m1/2. The work of fracture
obtained from the load-displacement curve of SENB test was 22.8
kJ.m-2. The composites exhibited excellent impact resistance and the
dynamic fracture toughness of 44.8 kJ.m-2 is achieved as determined
from instrumented Charpy impact test. The shear strength of the
composite was 93 MPa, which is significantly higher compared 2-D
Cf/SiC composites. Microstructure evaluation of fracture surfaces
revealed the signatures of fracture processes and showed good
support for the higher toughness obtained.
Abstract: This paper presents the electrical effect of two neighboring distribution substation during the construction phase. The size of auxiliary grounding grid have an effect on entire grounding system. The bigger the size of auxiliary grounding grid, the lower the GPR and maximum touch voltage, with the exception that when the two grids are unconnected, i.e. the bigger the size of auxiliary grounding grid, the higher the maximum step voltage. The results in this paper could be served as design guideline of grounding system, and perhaps remedy of some troublesome grounding grids in power distribution’s system. Modeling and simulation is carried out on the Current Distribution Electromagnetic interference Grounding and Soil structure (CDEGS) program. The simulation results exhibit the design and analysis of power system grounding and perhaps could be set as a standard in grounding system design and modification in distribution substations.
Abstract: In the process of information transmission (concept verbalization) we deal mostly with the substance (contents), and then pay attention to the form. Recalling events from the remote past, often we cannot exactly reproduce specific heard or pronounced words, as well as the syntactic structures. We remember events, feelings, images; we recall the general contents of the discourse. The thought gets a specific language form only during the concept verbalization phase. With minimum time for pondering, depending on the language competence level, the grammar and syntactic shaping often occurs automatically with the use of famous models and stereotypes. This means that the language form adapts itself to the consciousness, and not vice versa.
Abstract: Non-Government Organizations (NGOs), Non-Profit Organizations (NPOs), Social Enterprises and other actors play an important role in political decisions in governments at the international levels. Especially, such organizations’ and activists’ network in civil society is quite important to effect to the global politics. To solve the complex social problems in global era, diverse actors should corporate each other. Moreover, network of protesters is also contributes to diffuse tactics, information and other resources of social movements.
Based on the findings from the study of International Trade Fairs (ITFs), the author analyzes the network of activists in anti-globalism movement. This research focuses the transition of 54 activists’ whole network in the “protest event” against 2008 G8 summit in Japan. Their network is examined at the three periods: Before protest event phase, during protest event phase and after event phase. A mixed method is used in this study: the author shows the hypothesis from social network analysis and evaluates that with interview data analysis.
This analysis gives the two results. Firstly, the more protesters participate to the various events during the protest event, the more they build the network. After that, active protesters keep their network as well. From interview data, we can understand that the active protesters can build their network and diffuse the information because they communicate with other participants and understand that diverse issues are related.
This paper comes to same conclusion with previous researches: protest events activate the network among the political activists. However, some participants succeed to build their network, others do not. “Networked” activists are participated in the various events for short period of time and encourage the diffusion of information and tactics of social movements.
Abstract: In this work the effect of culturing conditions of filamentous fungi Penicillium raistrickii, Penicillium anatolicum, Fusarium sp. on biomass yield, the content of total lipids and fatty acids was studied. It has been established that in time the process of lipids accumulation correlated with biomass growth of cultures, reaching maximum values in stationary growth phase.
Biomass yield and accumulation of general lipids was increased by adding zinc to the culture medium. The more intensive accumulation of biomass and general lipids was observed at temperature 18°C. Lowering the temperature of culturing has changed the ratio of saturated: Unsaturated fatty acids in the direction of increasing the latter.
Abstract: The external flow simulation of a flying car at take off phase is a daunting task owing to the fact that the prediction of the transient unsteady flow features during its deployment phase is very complex. In this paper 3D numerical simulations of external flow of Ferrari F430 proposed flying car with different NACA 9618 rectangular wings have been carried. Additionally, the aerodynamics characteristics have been generated for optimizing its geometry for achieving the minimum take off velocity with better overall performance in both road and air. The three-dimensional standard k-omega turbulence model has been used for capturing the intrinsic flow physics during the take off phase. In the numerical study, a fully implicit finite volume scheme of the compressible, Reynolds-Averaged, Navier-Stokes equations is employed. Through the detailed parametric analytical studies we have conjectured that Ferrari F430 flying car facilitated with high wings having three different deployment histories during the take off phase is the best choice for accomplishing its better performance for the commercial applications.
Abstract: Laminar mixed Convection heat transfer of a nanofluid with prescribed constant heat flux on the inner wall of horizontal annular tube has been studied numerically based on two-phase mixture model in different Rayleigh Numbers and Azimuth angles. Effects of applying of different volume fractions of Al2O3 nanoparticles in water as a base fluid on hydrodynamic and thermal behaviors of the fluid flow such as axial velocity, secondary flow, temperature, heat transfer coefficient and friction coefficient at the inner and outer wall region, has been investigated. Conservation equations in elliptical form has been utilized and solved in three dimensions for a steady flow. It is observed that, there is a good agreement between results in this work and previously published experimental and numerical works on mixed convection in horizontal annulus. These particles cause to increase convection heat transfer coefficient of the fluid, meanwhile there is no considerable effect on friction coefficient.
Abstract: Ageing of 75% cold rolled Al-6Mg alloy with ternary 0.4 wt% scandium and quaternary zirconium and titanium has been carried out. Alloy samples are naturally, isochronally and isothermally aged for different time and temperatures. Hardness values of the differently processed alloys have been measured to understand the ageing behavior of Al-6Mg alloy with scandium and quaternary zirconium and titanium addition. Resistivity changes with annealing time and temperature were measured to understand the precipitation behavior and recovery of strain of the alloy. Attempts were also made to understand the grain refining effect of scandium in Al-6Mg alloy. It is observed that significant hardening takes place in the aged alloys due to the precipitation of scandium aluminides and the dendrites of the Al-6Mg alloy have been refined significantly due to addition of scandium.
Abstract: Progressive phase distribution is an important consideration in reflectarray antenna design which is required to form a planar wave in front of the reflectarray aperture. This paper presents a detailed mathematical model in order to determine the required reflection phase values from individual element of a reflectarray designed in Ku-band frequency range. The proposed technique of obtaining reflection phase can be applied for any geometrical design of elements and is independent of number of array elements. Moreover the model also deals with the solution of reflectarray antenna design with both centre and off-set feed configurations. The theoretical modeling has also been implemented for reflectarrays constructed on 0.508mm thickness of different dielectric substrates. The results show an increase in the slope of the phase curve from 4.61°/mm to 22.35°/mm by varying the material properties.