Abstract: In oases, the surface water resources are becoming
increasingly scarce and groundwater resources, which generally have
a poor quality due to the high levels of salinity, are often
overexploited. Water saving have therefore become imperative for
better oases sustainability. If drip irrigation is currently recommended
in Morocco for saving water and valuing, its use in the sub-desert
areas does not keep water safe from high evaporation rates. An
alternative to this system would be the use of subsurface drip
irrigation. This technique is defined as an application of water under
the soil surface through drippers, which deliver water at rates
generally similar to surface drip irrigation. As subsurface drip
irrigation is a recently introduced in Morocco, a better understanding
of the infiltration process around a buried source, in local conditions,
and its impact on plant growth is necessarily required. This study
aims to contribute to improving the water use efficiency by testing
the performance of subsurface irrigation system, especially in areas
where water is a limited source. The objectives of this research are
performance evaluation in arid conditions of the subsurface drip
irrigation system for young date palms compared to the surface drip.
In this context, an experimental test is installed at a farmer’s field in
the area of Erfoud (Errachidia Province, southeastern Morocco),
using the subsurface drip irrigation system in comparison with the
classic drip system for young date palms. Flow measurement to
calculate the uniformity of the application of water was done through
two methods: a flow measurement of drippers above the surface and
another one underground. The latter method has also helped us to
estimate losses through evaporation for both irrigation techniques. In
order to compare the effect of two irrigation modes, plants were
identified for each type of irrigation to monitor certain agronomic
parameters (cumulative numbers of palms and roots development).
Experimentation referred to a distribution uniformity of about 88%;
considered acceptable for subsurface drip irrigation while it is around
80% for the surface drip irrigation. The results also show an increase
in root development and in the number of palm, as well as a
substantial water savings due to lower evaporation losses compared
to the classic drip irrigation.
The results of this study showed that subsurface drip irrigation is
an efficient technique, which allows sustainable irrigation in arid
areas.
Abstract: Oases are complex and fragile agro-ecosystems. They
have always existed in environments characterized by an arid climate,
scarcity of rainfall, high temperatures and high evaporation. These
palms have grown up despite the severity of the physical
characteristics thanks to the water's existence and irrigation practice.
The oases are generally spread along non-perennial rivers (wadis),
shallow water table or deep artesian groundwater. However, the
sustainability of oasis system is threatened by water scarcity and
declining of water table levels particularly in arid areas. Located in
the southern east area of Morocco, Tafilalet plain encompasses one of
the largest palm groves in the kingdom. In recent years, this area has
become increasingly threatened by water shortage and has seen a
sharp deterioration under the effect of several combined
anthropogenic and climatic factors. The Bayoud disease, successive
years of drought, Hassan Addakhil dam construction etc are all
factors that have affected both water and phoenicicole heritage of the
area. The objective of this study is to understand the interaction
between qualitative and quantitative degradation of groundwater
resources, and the palm grove dynamics, while reviewing the
assumption that groundwater resources contribute in a direct way to
the conservation of this oasis agroecosystem. A historical analysis
tracing both the oasis dynamics and the groundwater evolution has
been established. Data were collected from satellite images, surveys
with different actors (farmers, Regional Office for Agricultural
Development, Basin agency...). They were complemented by a
synthesis of numerous technical reports in the area. The results
showed that within 40 years, the thickness of the groundwater table
has dropped in 50 %. Along with this, there has been a downsizing of
date palm by 50 %. Areas with higher groundwater level were the
least affected by the downsizing. So we can say that the shallow
groundwater contribute significantly and directly to the water supply
of date palm through its root system, and largely ensures the oasis
ecosystem sustainability.
Abstract: Yttrium oxide (Y2O3) films have been successfully
deposited with yttrium-ethylenediamine tetraacetic acid (EDTA·Y·H)
complexes prepared by various milling techniques. The effects of the
properties of the EDTA·Y·H complex on the properties of the
deposited Y2O3 films have been analyzed. Seven different types of the
raw EDTA·Y·H complexes were prepared by various commercial
milling techniques such as ball milling, hammer milling, commercial
milling, and mortar milling. The milled EDTA·Y·H complexes
exhibited various particle sizes and distributions, depending on the
milling method. Furthermore, we analyzed the crystal structure,
morphology and elemental distribution profile of the metal oxide films
deposited on stainless steel substrate with the milled EDTA·Y·H
complexes. Depending on the milling technique, the flow properties of
the raw powders differed. The X-ray diffraction pattern of all the
samples revealed the formation of Y2O3 crystalline phase, irrespective
of the milling technique. Of all the different milling techniques, the
hammer milling technique is considered suitable for fabricating dense
Y2O3 films.
Abstract: The hydrogenated amorphous carbon films (α-C:H)
were deposited on p-type Si (100) substrates at different thicknesses by
radio frequency plasma enhanced chemical vapor deposition
technique (rf-PECVD). Raman spectra display asymmetric
diamond-like carbon (DLC) peaks, representative of the α-C:H films.
The decrease of intensity ID/IG ratios revealed the sp3 content arise at
different thicknesses of the α-C:H films. In terms of mechanical
properties, the high hardness and elastic modulus values showed the
elastic and plastic deformation behaviors related to sp3 content in
amorphous carbon films. Electrochemical properties showed that the
α-C:H films exhibited excellent corrosion resistance in air-saturated
3.5 wt.% NaCl solution for pH 2 at room temperature. Thickness
increasing affected the small sp2 clusters in matrix, restricting the
velocity transfer and exchange of electrons. The deposited α-C:H films
exhibited excellent mechanical properties and corrosion resistance.
Abstract: Hydrogenated amorphous carbon (a-C:H) films have
been synthesized by a radio frequency plasma enhanced chemical
vapor deposition (rf-PECVD) technique with different bias voltage
from 0.0 to -0.5 kV. The Raman spectra displayed the polymer-like
hydrogenated amorphous carbon (PLCH) film with 0.0 to -0.1 and
a-C:H films with -0.2 to -0.5 kV of bias voltages. The surface chemical
information of all films were studied by X-ray photoelectron
spectroscopy (XPS) technique, presented to C-C (sp2 and sp3) and C-O
bonds, and relative carbon (C) and oxygen (O) atomics contents. The
O contamination had affected on structure and optical properties. The
true density of PLCH and a-C:H films were characterized by X-ray
refractivity (XRR) method, showed the result as in the range of
1.16-1.73 g/cm3 that depending on an increasing of bias voltage. The
hardness was proportional to the true density of films. In addition, the
optical properties i.e. refractive index (n) and extinction coefficient (k)
of these films were determined by a spectroscopic ellipsometry (SE)
method that give formation to in 1.62-2.10 (n) and 0.04-0.15 (k)
respectively. These results indicated that the optical properties
confirmed the Raman results as presenting the structure changed with
applied bias voltage increased.
Abstract: Online forum is part of a Learning Management
System (LMS) environment in which students share their opinions.
This study attempts to investigate the perceptions of students towards
online forum and their patterns of listening behavior during the forum
interaction. The students’ perceptions were measured using a
questionnaire, in which seven dimensions were used involving online
experience, benefits of forum participation, cost of participation,
perceived ease of use, usefulness, attitude, and intention. Meanwhile,
their patterns of listening behaviors were obtained using the log file
extracted from the LMS. A total of 25 postgraduate students
undertaking a course were involved in this study, and their activities
in the forum session were recorded by the LMS and used as a log file.
The results from the questionnaire analysis indicated that the students
perceived that the forum is easy to use, useful, and bring benefits to
them. Also, they showed positive attitude towards online forum, and
they have the intention to use it in future. Based on the log data, the
participants were also divided into six clusters of listening behavior,
in which they are different in terms of temporality, breadth, depth and
speaking level. The findings were compared to previous clusters
grouping and future recommendations are also discussed.
Abstract: Concerns on corrosion and effective coating
protection of double hull tankers and bulk carriers in service have
been raised especially in water ballast tanks (WBTs). Test
protocols/methodologies specifically that which is incorporated in the
International Maritime Organisation (IMO), Performance Standard
for Protective Coatings for Dedicated Sea Water ballast tanks (PSPC)
are being used to assess and evaluate the performance of the coatings
for type approval prior to their application in WBTs. However, some
of the type approved coatings may be applied as very thick films to
less than ideally prepared steel substrates in the WBT. As such films
experience hygrothermal cycling from operating and environmental
conditions, they become embrittled which may ultimately result in
cracking. This embrittlement of the coatings is identified as an
undesirable feature in the PSPC but is not mentioned in the test
protocols within it. There is therefore renewed industrial research
aimed at understanding this issue in order to eliminate cracking and
achieve the intended coating lifespan of 15 years in good condition.
This paper will critically review test protocols currently used for
assessing and evaluating coating performance, particularly the IMO
PSPC.
Abstract: Poly(lactic acid) (PLA) is a biodegradable polymer
which has good mechanical properties, however, its brittleness limits
its usage especially in packaging materials. Therefore, in this work,
PLA based polyurethane films were prepared by synthesizing with
different types of isocyanates; methylene diisocyanate (MDI) and
hexamethylene diisocyanates (HDI). For this purpose, PLA based
polyurethane must have good strength and flexibility. Therefore,
polycaprolactone which has better flexibility were prepared with
PLA. An effective way to endow polylactic acid with toughness is
through chain-extension reaction of the polylactic acid pre-polymer
with polycaprolactone used as chain extender. Polyurethane prepared
from MDI showed brittle behaviour, while, polyurethane prepared
from HDI showed flexibility at same concentrations.
Abstract: The rapid development and growth of technology has changed the method of obtaining information for educators and learners. Technology has created a new world of collaboration and communication among people. Incorporating new technology into the teaching process can enhance learning outcomes. Billions of individuals across the world are now connected together, and are cooperating and contributing their knowledge and intelligence. Time is no longer wasted in waiting until the teacher is ready to share information as learners can go online and get it immediatelt.
The objectives of this paper are to understand the reasons why changes in teaching and learning methods are necessary, to find ways of improving them, and to investigate the challenges that present themselves in the adoption of new ICT tools in higher education institutes.
To achieve these objectives two primary research methods were used: questionnaires, which were distributed among students at higher educational institutes and multiple interviews with faculty members (teachers) from different colleges and universities, which were conducted to find out why teaching and learning methodology should change.
The findings show that both learners and educators agree that educational technology plays a significant role in enhancing instructors’ teaching style and students’ overall learning experience; however, time constraints, privacy issues, and not being provided with enough up-to-date technology do create some challenges.
Abstract: Single-phase, high band gap energy Zn0.5Mg0.5O films were grown under oxygen pressure, using pulse laser deposition with a Zn0.5Mg0.5O target. Structural characterization studies revealed that the crystal structures of the ZnX-1MgXO films could be controlled via changes in the oxygen pressure. TEM analysis showed that the thickness of the deposited Zn1-xMgxO thin films was 50–75 nm. As the oxygen pressure increased, we found that one axis of the crystals did not show a very significant increase in the crystallization compared with that observed at low oxygen pressure. The X-ray diffraction peak intensity for the hexagonal-ZnMgO (002) plane increased relative to that for the cubic-ZnMgO (111) plane. The corresponding c-axis of the h-ZnMgO lattice constant increased from 5.141 to 5.148 Å, and the a-axis of the c-ZnMgO lattice constant decreased from 4.255 to 4.250 Å. EDX analysis showed that the Mg content in the mixed-phase ZnMgO films decreased significantly, from 54.25 to 46.96 at.%. As the oxygen pressure was increased from 100 to 150 mTorr, the absorption edge red-shifted from 3.96 to 3.81 eV; however, a film grown at the highest oxygen pressure tested here (200 mTorr).
Abstract: In this study, we developed a complementary electrochromic device consisting of WO3 and NiO films fabricated by rf-magnetron sputtered. The electrochromic properties of WO3 and NiO films were investigated using cyclic voltammograms (CV), performed on WO3 and NiO films immersed in an electrolyte of 1 M LiClO4 in propylene carbonate (PC). Optical and electrochemical of the films, as a function of coloration–bleaching cycle, were characterized using an UV-Vis-NIR spectrophotometer and cyclic voltammetry (CV). After investigating the properties of WO3 film, NiO film, and complementary electrochromic devices, we concluded that this device provides good reversibility, low power consumption of -2.5 V in color state, high variation of transmittance of 58.96%, changes in optical density of 0.81 and good memory effect under open-circuit conditions. In addition, electrochromic component penetration rate can be retained below 20% within 24h, showing preferred memory features; however, component coloring and bleaching response time are about 33s.
Abstract: In this study, the Mo-electrode thin films were deposited using two-stepped process and the high purity copper indium selenide-based powder (CuInSe2, CIS) was fabricated by using hydrothermal process by Nanowin Technology Co. Ltd. Because the CIS powder was aggregated into microscale particles, the CIS power was ground into nano-scale particles. 6 wt% CIS particles were mixed and dispersed into isopropyl alcohol (IPA). A new non-vacuum thin-film deposition process, spray coating method (SPM), was investigated to deposit the high-densified CIS absorber layers. 0.1 ml CIS solution was sprayed on the 20 mm×10 mm Mo/glass substrates and then the CuInSe2 thin films were annealed in a selenization furnace using N2 as atmosphere. The annealing temperature and time were set at 550oC and 5 min, and 0.0g~0.6g extra Se content was added in the furnace. The influences of extra Se content on the densification, crystallization, resistivity (ρ), hall mobility (μ), and carrier concentration of the CIS absorber layers were well investigated in this study.
Abstract: In this study, we investigated (In,Ga,Zn)Ox (IGZO) thin films and examined their characteristics of using Ga2O3-2 ZnO (GZO) co-sputtered In2O3 prepared by dual target radio frequency magnetron sputtering at room temperature in a pure Ar atmosphere. RF powers of 80 W and 70 W were used for GZO and pure In2O3, room temperature (RT) was used as deposition temperature, and the deposition time was changed from 15 min to 60 min. Structural, surface, electrical, and optical properties of IGZO thin films were investigated as a function of deposition time. Furthermore, the GZO co-sputtered In2O3 thin films showed a very smooth and featureless surface and an amorphous structure regardless of the deposition time due to the room temperature sputtering process. We would show that the co-sputtered IGZO thin films exhibited transparent electrode properties with high transmittance ratio and low resistivity.
Abstract: This work details the generation of thin films of
structured zeolite catalysts (ZSM–5 and Y) onto the surface of a
metal substrate (FeCrAlloy) using in-situ hydrothermal synthesis. In
addition, the zeolite Y is post-synthetically modified by acidified
ammonium ion exchange to generate US-Y. Finally the catalytic
activity of the structured ZSM-5 catalyst films (Si/Al = 11, thickness
146 0m) and structured US–Y catalyst film (Si/Al = 8, thickness
230m) were compared with the pelleted powder form of ZSM–5 and
USY catalysts of similar Si/Al ratios.
The structured catalyst films have been characterised using a range
of techniques, including X-ray diffraction (XRD), Electron
microscopy (SEM), Energy Dispersive X–ray analysis (EDX) and
Thermogravimetric Analysis (TGA). The transition from oxide-onalloy
wires to hydrothermally synthesised uniformly zeolite coated
surfaces was followed using SEM and XRD. In addition, the
robustness of the prepared coating was confirmed by subjecting these
to thermal cycling (ambient to 550oC).
The cracking of n–heptane over the pellets and structured catalysts
for both ZSM–5 and Y zeolite showed very similar product
selectivities for similar amounts of catalyst with an apparent
activation energy of around 60 kJ mol-1. This paper demonstrates that
structured catalysts can be manufactured with excellent zeolite
adherence and when suitably activated/modified give comparable
cracking results to the pelleted powder forms. These structured
catalysts will improve temperature distribution in highly exothermic
and endothermic catalysed processes.
Abstract: RF magnetron sputtering is used on the ceramic targets, each of which contains zinc oxide (ZnO), zinc oxide doped with aluminum (AZO) and zinc oxide doped with gallium (GZO). The electric conduction mechanism of the AZO and GZO films came mainly from the Al and Ga, the oxygen vacancies, Zn interstitial atoms, and Al and/or Ga interstitial atoms. AZO and GZO films achieved higher conduction than did ZnO film, it being ion vacant and nonstoichiometric. The XRD analysis showed a preferred orientation along the (002) plane for ZnO, AZO, and GZO films.
Abstract: We present a modeling framework that supports the engineering of early requirements specifications for design of learner centric dynamic Learning Management System. The framework is based on i* modeling tool and Means End Analysis, that adopts primitive concepts for modeling early requirements (such as actor, goal, and strategic dependency). We show how pedagogical and computational requirements for designing a learner centric Learning Management system can be adapted for the automatic early requirement engineering specifications. Finally, we presented a model on a Learner Quanta based adaptive Courseware. Our early requirement analysis shows that how means end analysis reveals gaps and inconsistencies in early requirements specifications that are by no means trivial to discover without the help of formal analysis tool.
Abstract: Microfibrous palygorskite and tubular halloysite clay mineral combined with nanocrystalline TiO2 are incorporating in the preparation of nanocomposite films on glass substrates via sol-gel route at 450oC. The synthesis is employing nonionic surfactant molecule as pore directing agent along with acetic acid-based sol-gel route without addition of water molecules. Drying and thermal treatment of composite films ensure elimination of organic material lead to the formation of TiO2 nanoparticles homogeneously distributed on the palygorskite or halloysite surfaces. Nanocomposite films without cracks of active anatase crystal phase on palygorskite and halloysite surfaces are characterized by microscopy techniques, UV-Vis spectroscopy, and porosimetry methods in order to examine their structural properties.
The composite palygorskite-TiO2 and halloysite-TiO2 films with variable quantities of palygorskite and halloysite were tested as photocatalysts in the photo-oxidation of Basic Blue 41 azo dye in water. These nanocomposite films proved to be most promising photocatalysts and highly effective to dye’s decoloration in spite of small amount of palygorskite-TiO2 or halloysite-TiO2 catalyst immobilized onto glass substrates mainly due to the high surface area and uniform distribution of TiO2 on clay minerals avoiding aggregation.
Abstract: Prognostic studies of the shoreline are of utmost importance for Ponta Negra Beach, located in Natal, Northeastern Brazil, where the infrastructure recently built along the shoreline is severely affected by flooding and erosion. This study compares shoreline predictions using three linear regression methods (LMS, LRR and WLR) and tries to discern the best method for different shoreline position scenarios. The methods have shown erosion on the beach in each of the scenarios tested, even in less intense dynamic conditions. The WLA_A with confidence interval of 95% was the well-adjusted model and calculated a retreat of -1.25 m/yr to -2.0 m/yr in hot spot areas. The change of the shoreline on Ponta Negra Beach can be measured as a negative exponential curve. Analysis of these methods has shown a correlation with the morphodynamic stage of the beach.
Abstract: A thin gold metal layer was deposited on the top of
silicon oxide films containing embedded Si nanocrystals (Si-nc). The
sample was annealed in a gas containing nitrogen, and subsequently
characterized by photoluminescence. We obtained 3-fold
enhancement of photon emission from the Si-nc embedded in silicon
dioxide covered with a Gold layer as compared with an uncovered
sample. We attribute this enhancement to the increase of the
spontaneous emission rate caused by the coupling of the Si-nc
emitters with the surface plasmons (SP). The evolution of PL
emission with laser irradiated time was also collected from covered
samples, and compared to that from uncovered samples. In an
uncovered sample, the PL intensity decreases with time,
approximately with two decay constants. Although the decrease of
the initial PL intensity associated with the increase of sample
temperature under CW pumping is still observed in samples covered
with a gold layer, this film significantly contributes to reduce the
permanent deterioration of the PL intensity. The resistance to
degradation of light-emitting silicon nanocrystals can be increased by
SP coupling to suppress the permanent deterioration. Controlling the
permanent photodeterioration can allow to perform a reliable optical
gain measurement.
Abstract: Cd1−xZnxS thins films have been fabricated from ZnS/CdS/ZnS multilayer thin film systems, by using the vacuum deposition method; the Rutherford backscattering (RBS) technique have been applied in order to determine the: structure, composition, depth profile, and stoichiometric of these films. The influence of the chemical and heat treatments on the produced films also have been investigated; the RBS spectra of the films showed that homogenous Cd1−xZnxS can be synthesized with x=0.45.