Abstract: In this work we study the thermodynamic behavior of some ventilated facades under summer operating conditions in Southern Spain. Under these climatic conditions, indoor comfort implies a high energetic demand due to high temperatures that usually are reached in this season in the considered geographical area.
The aim of this work is to determine if during summer operating conditions in Southern Spain, ventilated façades provide some energy saving compared to the non-ventilated façades and to deduce their behavior patterns in terms of energy efficiency.
The modelization of the air flow in the channel has been performed by using Navier-Stokes equations for thermodynamic flows. Numerical simulations have been carried out with a 2D Finite Element approach.
This way, we analyze the behavior of ventilated façades under different weather conditions as variable wind, variable temperature and different levels of solar irradiation.
CFD computations show the combined effect of the shading of the external wall and the ventilation by the natural convection into the air gap achieve a reduction of the heat load during the summer period. This reduction has been evaluated by comparing the thermodynamic performances of two ventilated and two unventilated façades with the same geometry and thermophysical characteristics.
Abstract: Nowadays, in most radiotherapy departments, the commercial treatment planning systems (TPS) used to calculate dose distributions needs to be verified; therefore, quick, easy-to-use and low cost dose distribution algorithms are desirable to test and verify the performance of the TPS. In this paper, we put forth an analytical method to calculate the phantom scatter contribution and depth dose on the central axis based on the equivalent square concept. Then, this method was generalized to calculate the profiles at any depth and for several field shapes regular or irregular fields under symmetry and asymmetry photon beam conditions. Varian 2100 C/D and Siemens Primus Plus Linacs with 6 and 18 MV photon beam were used for irradiations. Percentage depth doses (PDDs) were measured for a large number of square fields for both energies, and for 45º wedges which were employed to obtain the profiles in any depth. To assess the accuracy of the calculated profiles, several profile measurements were carried out for some treatment fields. The calculated and measured profiles were compared by gamma-index calculation. All γ–index calculations were based on a 3% dose criterion and a 3 mm dose-to-agreement (DTA) acceptance criterion. The γ values were less than 1 at most points. However, the maximum γ observed was about 1.10 in the penumbra region in most fields and in the central area for the asymmetric fields. This analytical approach provides a generally quick and fairly accurate algorithm to calculate dose distribution for some treatment fields in conventional radiotherapy.
Abstract: The aim of the study is evaluation of absorbed doses for thyroids by using neck phantoms. For this purpose, it was arranged the irradiation set with different phantoms. Three different materials were used for phantom materials as, water, parafine and wood. The phantoms were three different dimensions for simulation of different ages and human race for each material. Co-60 gammao source was used for irradiation and the experimental procedure applied rigorously with narrow beam geometry. As the results of the experiments the relative radiation doses are evaluated for therapic applications for thyroids and backscattering factors were calculated and shown that water, parafine and wood can appropriate for phantom material with the converge values of backscattering factors.
Abstract: The goal of this paper is to examine the effects of laser
radiation on the skin wound healing using infrared thermography as
non-invasive method for the monitoring of the skin temperature
changes during laser treatment. Thirty Wistar rats were used in this
study. A skin lesion was performed at the leg on all rats. The animals
were exposed to laser radiation (λ = 670 nm, P = 15 mW, DP = 16.31
mW/cm2) for 600 s. Thermal images of wound were acquired before
and after laser irradiation. The results have demonstrated that the
tissue temperature decreases from 35.5±0.50°C in the first treatment
day to 31.3±0.42°C after the third treatment day. This value is close
to the normal value of the skin temperature and indicates the end of
the skin repair process. In conclusion, the improvements in the
wound healing following exposure to laser radiation have been
revealed by infrared thermography.
Abstract: Overhead electrical insulators form an important link in an electric power system. Along with the traditional insulators (i.e. glass and porcelain, etc) presently the polymeric insulators are also used world widely. These polymeric insulators are very sensitive to various environmental parameters such temperature, environmental pollution, UV-radiations, etc. which seriously effect their electrical, chemical and hydrophobic properties. The UV radiation level in the central region of Saudi Arabia is high as compared to the IEC standard for the accelerated aging of the composite insulators. Commonly used suspension type of composite EPDM (Ethylene Propylene Diene Monomer) insulator was subjected to accelerated stress aging as per modified IEC standard simulating the inland arid deserts atmospheric condition and also as per IEC-61109 standard. The hydrophobic characteristics were studied by measuring the contact angle along the insulator surface before and after the accelerated aging of the samples. It was found that EPDM insulator loses it hydrophobic properties proportional to the intensity of UV irradiations and its rate of recovery is also very low as compared to Silicone Rubber insulator.KeywordsEPDM, composite insulators, accelerated aging, hydrophobicity, contact angle.
Abstract: ZnO nanostructure were synthesized via microwave
method using zinc acetate as starting material, guanidinium as
structure directing agents, and water as solvent.. This work
investigates the photodegradation of azo dyes using the ZnO Flowerlike
in aqueous solutions. As synthesized ZnO samples were
characterized using X-Ray powder diffraction (XRD), scanning
electron microscopy (SEM), and FTIR spectroscopy.In this work
photodecolorization of congored azo dye under UV irradiation by
nano ZnO was studied.
Abstract: This article summarizes ways to verify neutron
fluence for neutron transmutation doping of silicon with phosphorus
on the LVR-15 reactor. Neutron fluence is determined using
activation detectors placed along the crystal in a strip or encapsulated
in a rod holder. Holders are placed at the centre of a water-filled
capsule or in an aluminum or silicon ingot that simulates a real single
crystal. If the diameter of the crystal is significantly less than the
capsule diameter and water from the primary circuit enters the free
space in the capsule, neutron interaction in the water changes neutron
fluence, affecting axial irradiation homogeneity. The effect of
moving the capsule vertically in the channel relative to maximum
neutron fluence in the reactor core was also measured. Even a small
shift of the capsule-s centre causes great irradiation inhomogeneity.
This effect was measured using activation detectors, and was also
confirmed by MCNP calculation.
Abstract: This paper presents a 2-D hydrodynamic model of the ablated plasma when irradiating a 50 μm Al solid target with a single pulsed ion beam. The Lagrange method is used to solve the moving fluid for the ablated plasma production and formation mechanism. In the calculations, a 10-ns-single-pulsed of ion beam with a total energy density of 120 J/cm2, is used. The results show that the ablated plasma was formed after 2 ns of ion beam irradiation and it started to expand right after 4-6 ns. In addition, the 2-D model give a better understanding of pulsed ion beam-solid target ablated plasma production and expansion process clearer.
Abstract: A theoretical approach to radiation damage evolution
is developed. Stable temporal behavior taking place in solids under
irradiation are examined as phenomena of self-organization in nonequilibrium
systems.
Experimental effects of temporal self-organization in solids under
irradiation are reviewed. Their essential common properties and
features are highlighted and analyzed.
Dynamical model to describe development of self-oscillation of
density of point defects under stationary irradiation is proposed. The
emphasis is the nonlinear couplings between rate of annealing and
density of defects that determine the kind and parameters of an
arising self-oscillation.
The field of parameters (defect generation rate and environment
temperature) at which self-oscillations develop is found. Bifurcation
curve and self-oscillation period near it is obtained.
Abstract: This work describes refrigeration effects during storage on total protein and amino acids composition of raw and processed flour of two pearl millet cultivars (Ashana and Dembi). The protein content of the whole raw flour was found to be 14.46 and 13.38% for Ashana and Dembi cultivars, respectively. Dehulling of the grains reduced the protein content to 13.38 and 12.67% for the cultivars, respectively. For both cultivars, the protein content of the whole and dehulled raw flour before and after cooking was slightly decreased when the flour was stored for 60 days even after refrigeration. The effect of refrigeration process in combination with the storage period, cooking or dehulling was found to be vary between amino acids and even between cultivars. Regardless of the storage period and processing method, the amino acids content was remained unchanged after refrigeration for both cultivars.
Abstract: In this paper, an approach for finding optimized
layouts for connecting PV units delivering maximum array output
power is suggested. The approach is based on considering the
different varying parameters of PV units that might be extracted from
a general two-diode model. These are mainly, solar irradiation,
reverse saturation currents, ideality factors, series and shunt
resistances in addition to operating temperature. The approach has
been tested on 19 possible 2×3 configurations and allowed to
determine the optimized configurations as well as examine the effects
of the different units- parameters on the maximum output power.
Thus, using this approach, standard arrays with n×m units can be
configured for maximum generated power and allows designing PV
based systems having reduced surfaces to fit specific required power,
as it is the case for solar cars and other mobile systems.
Abstract: In this study three commercial semiconductor devices
were characterized in the laboratory for computed tomography
dosimetry: one photodiode and two phototransistors. It was evaluated
four responses to the irradiation: dose linearity, energy dependence,
angular dependence and loss of sensitivity after X ray exposure. The
results showed that the three devices have proportional response with
the air kerma; the energy dependence displayed for each device
suggests that some calibration factors would be applied for each one;
the angular dependence showed a similar pattern among the three
electronic components. In respect to the fourth parameter analyzed,
one phototransistor has the highest sensitivity however it also showed
the greatest loss of sensitivity with the accumulated dose. The
photodiode was the device with the smaller sensitivity to radiation,
on the other hand, the loss of sensitivity after irradiation is negligible.
Since high accuracy is a desired feature for a dosimeter, the
photodiode can be the most suitable of the three devices for
dosimetry in tomography. The phototransistors can also be used for
CT dosimetry, however it would be necessary a correction factor due
to loss of sensitivity with accumulated dose.
Abstract: The effect of gamma irradiation on micro-hardness of polymer blends of poly (ethyl methacrylate)(PEMA) and poly (ethylene oxide) (PEO) has been investigated to detect the radiation induced crosslinking. The blend system comprises a noncrystallizable polymer, PEMA and a crystallizable polymer, PEO. On irradiation, the overall hardness of the blend specimens for different dose levels infers occurrence of a crosslinking process. The radiation-induced crosslinking was greater for blends having lower concentration of PEO. However, increase in radiation dose causes softening of blend system due to radiation induced scissioning of the chains
Abstract: Photo-crosslinked rice starch-based biodegradable
films were prepared by casting film-solution on leveled trays and
ultra violet (UV) irradiation was applied for 10 minute. The effect of
the content (3%, 6% and 9 wt. %)of photosensitiser (sodium
benzoate) on mechanical properties, water vapor permeability (WVP)
and structural properties of rice starch films were investigated. The
tensile strength increased while elongation at break and water
resistance properties of rice starch films decreased with addition and
increasing content of photosensitiser. The % crystallinity of rice
starch films were decreased when the content of photosensitiser
increased and UV were applied. The results showed that the
carboxylate group band of sodium benzoate was found in the FTIR
spectrum of rice starch films and found that incorporation of 6% of
photosensitiser into the films showed a higher absorption band of
resulted films. This result pointed out the highest interaction between
starch molecules was occurred.
Abstract: Staphylococcus aureus, one of the microflora in a
human external auditory canal (EAC) is frequently exposed to highfrequency
electromagnetic field (HF-EMF) generated by mobile
phones. It is normally non-pathogenic but in certain circumstances, it
can cause infections. This study investigates the changes in the
physiology of S. aureus when exposed to HF-EMF of a mobile
phone. Exponentially grown S. aureus were exposed to two
conditions of EMF irradiation (standby-mode and on-call mode) at
four durations; 15, 30, 45 and 60 min. Changes in the viability and
biofilm production of the S. aureus were compared between the two
conditions of exposure. EMF from the standby-mode has enhanced
the growth of S. aureus but during on-call, the growth was
suppressed. No significant difference in the amount of biofilm
produced in both modes of exposure was observed. Thus, HF-EMF
of mobile phone affects the viability of S. aureus but not its ability to
produce biofilm.
Abstract: Cu-mesoporous TiO2 is developed for removal acid
odor cooperated with ozone assistance and online- regeneration
system with/without UV irradiation (all weather) in study. The results
showed that Cu-mesoporous TiO2 present the desirable adsorption
efficiency of acid odor without UV irradiation, due to the larger
surface area, pore sizeand the additional absorption ability provided by
Cu. In the photocatalysis process, the material structure also benefits
Cu-mesoporous TiO2 to perform the more outstanding efficiency on
degrading acid odor. Cu also postponed the recombination of
electron-hole pairs excited from TiO2 to enhance photodegradation
ability. Cu-mesoporous TiO2 could gain the conspicuous increase on
photocatalysis ability from ozone assistance, but without any benefit
on adsorption. In addition, the online regeneration procedure could
process the used Cu-mesoporous TiO2 to reinstate the adsorption
ability and maintain the photodegradtion performance, depended on
scrubbing, desorping acid odor and reducing Cu to metal state.
Abstract: In medical therapy, laser has been widely used to conduct cosmetic, tumor and other treatments. During the process of laser irradiation, there may be thermal damage caused by excessive laser exposure. Thus, the establishment of a complete thermal analysis model is clinically helpful to physicians in reference data. In this study, porcine liver in place of tissue was subjected to laser irradiation to set up the experimental data considering the explored impact on surface thermal field and thermal damage region under different conditions of power, laser irradiation time, and distance between laser and porcine liver. In the experimental process, the surface temperature distribution of the porcine lever was measured by the infrared thermal imager. In the part of simulation, the bio heat transfer Pennes-s equation was solved by software SYSWELD applying in welding process. The double ellipsoid function as a laser source term is firstly considered in the prediction for surface thermal field and internal tissue damage. The simulation results are compared with the experimental data to validate the mathematical model established here in.
Abstract: As known that efficiency of photovoltaic cells is not
high as desired level. Efficiency of PVs could be improved by
selecting convenient locations that have high solar irradiation,
sunshine duration, mild temperature, low level air pollution and dust
concentration. Additionally, some environmental parameters called
derating factors effect to decrease PV efficiencies such as cloud, high
temperature, aerosol optical depth, high dust concentration, shadow,
snow, humidity etc. In this paper, all parameters that effect PV
efficiency are considered in detail under climatic conditions of
Istanbul. A 750 Wp PV system with measurement devices is
constructed in Maslak campus of Istanbul Technical University.
Abstract: In our recent study, we have used ZnO nanoparticles assisted with UV light irradiation to investigate the photocatalytic degradation of Phenol Red (PR). The ZnO photocatalyst was characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), specific surface area analysis (BET) and UVvisible spectroscopy. X-ray diffractometry result for the ZnO nanoparticles exhibit normal crystalline phase features. All observed peaks can be indexed to the pure hexagonal wurtzite crystal structures, with the space group of P63mc. There are no other impurities in the diffraction peak. In addition, TEM measurement shows that most of the nanoparticles are rod-like and spherical in shape and fairly monodispersed. A significant degradation of the PR was observed when the catalyst was added into the solution even without the UV light exposure. In addition, the photodegradation increases with the photocatalyst loading. The surface area of the ZnO nanomaterials from the BET measurement was 11.9 m2/g. Besides the photocatalyst loading, the effect of some parameters on the photodegradation efficiency such as initial PR concentration and pH were also studied.
Abstract: The characterization of κ-carrageenan could provide a
better understanding of its functions in biological, medical and
industrial applications. Chemical and physical analyses of
carrageenan from seaweeds, Euchema cottonii L., were done to offer
information on its properties and the effects of Co-60 γ-irradiation on
its thermochemical characteristics. The structural and morphological
characteristics of κ-carrageenan were determined using scanning
electron microscopy (SEM) while the composition, molecular weight
and thermal properties were determined using attenuated total
reflectance Fourier transform infrared spectroscopy (ATR-FTIR), gel
permeation chromatography (GPC), thermal gravimetric analysis
(TGA) and differential scanning calorimetry (DSC). Further chemical
analysis was done using hydrogen-1 nuclear magnetic resonance (1H
NMR) and functional characteristics in terms of biocompatibility
were evaluated using cytotoxicity test.