Abstract: Compliant foil gas lubricated bearings are used for the
support of light loads in the order of few kilograms at high speeds, in
the order of 50,000 RPM. The stiffness of the foil bearings depends
both on the stiffness of the compliant foil and on the lubricating
gas film. The stiffness of the bearings plays a crucial role in the
stable operation of the supported rotor over a range of speeds. This
paper describes a numerical approach to estimate the stiffness of the
bearings using pseudo spectral scheme. Methodology to obtain the
stiffness of the foil bearing as a function of weight of the shaft is
given and the results are presented.
Abstract: Digital signal processor, image signal processor and FIR filters have multipliers as an important part of their design. On the basis of Vedic mathematics, Vedic multipliers have come out to be very fast multipliers. One of the image processing applications is edge detection. This research presents a small area and high speed 8 bit Vedic multiplier system comprising of compressor based adders. This results in faster edge detection. This architecture is tested on Xilinx vertex 4 FPGA board and simulations were carried out using the Xilinx synthesis tool. Comparisons are made and this system is found to be smaller in area with high speed (the lesser propagation delay). This compressor based Vedic multiplier is 1.1 times speedier than a typical Vedic multiplier. Also, this Vedic Multiplier is 2 times speedier than a ‘simple’ multiplier.
Abstract: Data driven dynamic logic is the high speed dynamic circuit with low area. The clock of the dynamic circuit is removed and data drives the circuit instead of clock for precharging purpose. This data driven dynamic nand gate is given static forward substrate biasing of Vsupply/2 as well as the substrate bias is connected to the input data, resulting in dynamic substrate bias. The dynamic substrate bias gives the shortest propagation delay with a penalty on the power dissipation. Propagation delay is reduced by 77.8% compared to the normal reverse substrate bias Data driven dynamic nand. Also dynamic substrate biased D3nand’s propagation delay is reduced by 31.26% compared to data driven dynamic nand gate with static forward substrate biasing of Vdd/2. This data driven dynamic nand gate with dynamic body biasing gives us the highest speed with no area penalty and finds its applications where power penalty is acceptable. Also combination of Dynamic and static Forward body bias can be used with reduced propagation delay compared to static forward biased circuit and with comparable increase in an average power. The simulations were done on hspice simulator with 22nm High-k metal gate strained Si technology HP models of Arizona State University, USA.
Abstract: In this paper we presented a new method for tracking
flying targets in color video sequences based on contour and kernel.
The aim of this work is to overcome the problem of losing target in
changing light, large displacement, changing speed, and occlusion.
The proposed method is made in three steps, estimate the target
location by particle filter, segmentation target region using neural
network and find the exact contours by greedy snake algorithm. In
the proposed method we have used both region and contour
information to create target candidate model and this model is
dynamically updated during tracking. To avoid the accumulation of
errors when updating, target region given to a perceptron neural
network to separate the target from background. Then its output used
for exact calculation of size and center of the target. Also it is used as
the initial contour for the greedy snake algorithm to find the exact
target's edge. The proposed algorithm has been tested on a database
which contains a lot of challenges such as high speed and agility of
aircrafts, background clutter, occlusions, camera movement, and so
on. The experimental results show that the use of neural network
increases the accuracy of tracking and segmentation.
Abstract: Device-to-device (D2D) communication is considered a
promising technique to provide wireless peer-to-peer communication
services. Due to increasing demand on mobile services, available
spectrum for radio frequency (RF) based communications becomes
scarce. Recently, visible light communications (VLC) has evolved
as a high speed wireless data transmission technology for indoor
environments with abundant available bandwidth. In this paper,
a novel VLC based D2D communication that provides wireless
peer-to-peer communication is proposed. Potential low operating
power devices for an efficient D2D communication over increasing
distance of separation between devices is analyzed. Optical repeaters
(OR) are also proposed to enhance the performance in an environment
where direct D2D communications yield degraded performance.
Simulation results show that VLC plays an important role in
providing efficient D2D communication up to a distance of 1 m
between devices. It is also found that the OR significantly improves
the coverage distance up to 3.5 m.
Abstract: This paper describes a simple way to control the speed
of PMBLDC motor using Fuzzy logic control method. In the
conventional PI controller the performance of the motor system is
simulated and the speed is regulated by using PI controller. These
methods used to improve the performance of PMSM drives, but in
some cases at different operating conditions when the dynamics of
the system also vary over time and it can change the reference speed,
parameter variations and the load disturbance. The simulation is
powered with the MATLAB program to get a reliable and flexible
simulation. In order to highlight the effectiveness of the speed control
method the FLC method is used. The proposed method targeted in
achieving the improved dynamic performance and avoids the
variations of the motor drive. This drive has high accuracy, robust
operation from near zero to high speed. The effectiveness and
flexibility of the individual techniques of the speed control method
will be thoroughly discussed for merits and demerits and finally
verified through simulation and experimental results for comparative
analysis.
Abstract: This paper outlines the development of an
experimental technique in quantifying supersonic jet flows, in an
attempt to avoid seeding particle problems frequently associated with
particle-image velocimetry (PIV) techniques at high Mach numbers.
Based on optical flow algorithms, the idea behind the technique
involves using high speed cameras to capture Schlieren images of the
supersonic jet shear layers, before they are subjected to an adapted
optical flow algorithm based on the Horn-Schnuck method to
determine the associated flow fields. The proposed method is capable
of offering full-field unsteady flow information with potentially
higher accuracy and resolution than existing point-measurements or
PIV techniques. Preliminary study via numerical simulations of a
circular de Laval jet nozzle successfully reveals flow and shock
structures typically associated with supersonic jet flows, which serve
as useful data for subsequent validation of the optical flow based
experimental results. For experimental technique, a Z-type Schlieren
setup is proposed with supersonic jet operated in cold mode,
stagnation pressure of 4 bar and exit Mach of 1.5. High-speed singleframe
or double-frame cameras are used to capture successive
Schlieren images. As implementation of optical flow technique to
supersonic flows remains rare, the current focus revolves around
methodology validation through synthetic images. The results of
validation test offers valuable insight into how the optical flow
algorithm can be further improved to improve robustness and
accuracy. Despite these challenges however, this supersonic flow
measurement technique may potentially offer a simpler way to
identify and quantify the fine spatial structures within the shock shear
layer.
Abstract: This research paper presents highly optimized barrel
shifter at 22nm Hi K metal gate strained Si technology node. This
barrel shifter is having a unique combination of static and dynamic
body bias which gives lowest power delay product. This power delay
product is compared with the same circuit at same technology node
with static forward biasing at ‘supply/2’ and also with normal reverse
substrate biasing and still found to be the lowest. The power delay
product of this barrel sifter is .39362X10-17J and is lowered by
approximately 78% to reference proposed barrel shifter at 32nm bulk
CMOS technology. Power delay product of barrel shifter at 22nm Hi
K Metal gate technology with normal reverse substrate bias is
2.97186933X10-17J and can be compared with this design’s PDP of
.39362X10-17J. This design uses both static and dynamic substrate
biasing and also has approximately 96% lower power delay product
compared to only forward body biased at half of supply voltage. The
NMOS model used are predictive technology models of Arizona state
university and the simulations to be carried out using HSPICE
simulator.
Abstract: Crosstalk among interconnects and printed-circuit
board (PCB) traces is a major limiting factor of signal quality in highspeed
digital and communication equipments especially when fast
data buses are involved. Such a bus is considered as a planar
multiconductor transmission line. This paper will demonstrate how
the finite difference time domain (FDTD) method provides an exact
solution of the transmission-line equations to analyze the near end
and the far end crosstalk. In addition, this study makes it possible to
analyze the rise time effect on the near and far end voltages of the
victim conductor. The paper also discusses a statistical analysis,
based upon a set of several simulations. Such analysis leads to a
better understanding of the phenomenon and yields useful
information.
Abstract: Present paper describes method of obtaining clay
ceramic foam (CCF) and foam concrete (FC), by direct foaming with
high speed mixer-disperser (HSMD). Three foaming agents (FA) are
compared for the FC and CCF production: SCHÄUMUNGSMITTEL
W 53 FLÜSSIG (Zschimmer & Schwarz Gmbh, Germany), SCF-
1245 (Sika, test sample, Latvia) and FAB-12 (Elade, Latvija). CCF
were obtained at 950, 1000°C, 1150°C and 1150°C firing temperature
and have mechanical compressive strength 1.2, 2.55 and 4.3 MPa and
porosity 79.4, 75.1, 71.6%, respectively. Obtained FC has 6-14 MPa
compressive strength and porosity 44-55%. The goal of this work
was development of a sustainable and durable ceramic cellular
structures using HSMD.
Abstract: The distribution of a single global clock across a chip
has become the major design bottleneck for high performance VLSI
systems owing to the power dissipation, process variability and multicycle
cross-chip signaling. A Network-on-Chip (NoC) architecture
partitioned into several synchronous blocks has become a promising
approach for attaining fine-grain power management at the system
level. In a NoC architecture the communication between the blocks is
handled asynchronously. To interface these blocks on a chip
operating at different frequencies, an asynchronous FIFO interface is
inevitable. However, these asynchronous FIFOs are not required if
adjacent blocks belong to the same clock domain. In this paper, we
have designed and analyzed a 16-bit asynchronous micropipelined
FIFO of depth four, with the awareness of place and route on an
FPGA device. We have used a commercially available Spartan 3
device and designed a high speed implementation of the
asynchronous 4-phase micropipeline. The asynchronous FIFO
implemented on the FPGA device shows 76 Mb/s throughput and a
handshake cycle of 109 ns for write and 101.3 ns for read at the
simulation under the worst case operating conditions (voltage =
0.95V) on a working chip at the room temperature.
Abstract: Fixed-geometry hydrodynamic journal bearings are
one of the best supporting systems for several applications of rotating
machinery. Cylindrical journal bearings present excellent loadcarrying
capacity and low manufacturing costs, but they are subjected
to the oil-film instability at high speeds. An attempt of overcoming
this instability problem has been the development of non-circular
journal bearings. This work deals with an analysis of oil-lubricated
elliptical journal bearings using the finite element method. Steadystate
and dynamic performance characteristics of elliptical bearings
are rendered by zeroth- and first-order lubrication equations obtained
through a linearized perturbation method applied on the classical
Reynolds equation. Four-node isoparametric rectangular finite
elements are employed to model the bearing thin film flow. Curves of
elliptical bearing load capacity and dynamic force coefficients are
rendered at several operating conditions. The results presented in this
work demonstrate the influence of the bearing ellipticity on its
performance at different loading conditions.
Abstract: Today’s VLSI networks demands for high speed. And
in this work the compact form mathematical model for current mode
signalling in VLSI interconnects is presented.RLC interconnect line
is modelled using characteristic impedance of transmission line and
inductive effect. The on-chip inductance effect is dominant at lower
technology node is emulated into an equivalent resistance. First order
transfer function is designed using finite difference equation, Laplace
transform and by applying the boundary conditions at the source and
load termination. It has been observed that the dominant pole
determines system response and delay in the proposed model. The
novel proposed current mode model shows superior performance as
compared to voltage mode signalling. Analysis shows that current
mode signalling in VLSI interconnects provides 2.8 times better
delay performance than voltage mode. Secondly the damping factor
of a lumped RLC circuit is shown to be a useful figure of merit.
Abstract: Cemented carbide balls are usually implemented in
industry under the environment of high speed, high temperature,
corrosiveness and strong collisions. However, its application is limited
due to high fabrication cost, processing efficiency and quality. A novel
eccentric lapping method with two rotatable lapping plates was
proposed in this paper. A mathematical model was constructed to
analyze the influence of each design parameter on this lapping method.
To validate this new lapping method, an orthogonal experiment was
conducted with cemented carbide balls (YG6). The simulation model
was verified and the optimal lapping parameters were derived. The
results show that the surface roundness of the balls reaches to 0.65um
from 2um in 1 hour using this lapping method. So, using this novel
lapping method, it can effectively improve the machining precision
and efficiency of cemented carbide balls.
Abstract: IEEE 802.16 (WiMAX) aims to present high speed
wireless access to cover wide range coverage. The base station (BS)
and the subscriber station (SS) are the main parts of WiMAX.
WiMAX uses either Point-to-Multipoint (PMP) or mesh topologies.
In the PMP mode, the SSs connect to the BS to gain access to the
network. However, in the mesh mode, the SSs connect to each other
to gain access to the BS.
The main components of QoS management in the 802.16 standard
are the admission control, buffer management and packet scheduling.
In this paper, we use QualNet 5.0.2 to study the performance of
different scheduling schemes, such as WFQ, SCFQ, RR and SP when
the numbers of SSs increase. We find that when the number of SSs
increases, the average jitter and average end-to-end delay is increased
and the throughput is reduced.
Abstract: Vancron 40, a nitrided powder metallurgical tool
Steel, is used in cold work applications where the predominant failure
mechanisms are adhesive wear or galling. Typical applications of
Vancron 40 are among others fine blanking, cold extrusion, deep
drawing and cold work rolls for cluster mills. Vancron 40 positive
results for cold work rolls for cluster mills and as a tool for some
severe metal forming process makes it competitive compared to other
type of work rolls that require higher precision, among others in cold
rolling of thin stainless steel, which required high surface finish
quality. In this project, three roll materials for cold rolling of stainless
steel strip was examined, Vancron 40, Narva 12B (a high-carbon,
high-chromium tool steel alloyed with tungsten) and Supra 3 (a
Chromium-molybdenum tungsten-vanadium alloyed high speed
steel). The purpose of this project was to study the depth profiles of
the ironed stainless steel strips, emergence of galling and to study the
lubrication performance used by steel industries. Laboratory
experiments were conducted to examine scratch of the strip, galling
and surface roughness of the roll materials under severe tribological
conditions. The critical sliding length for onset of galling was
estimated for stainless steel with four different lubricants. Laboratory
experiments result of performance evaluation of resistance capability
of rolls toward adhesive wear under severe conditions for low and
high reductions. Vancron 40 in combination with cold rolling
lubricant gave good surface quality, prevents galling of
metal surfaces and good bearing capacity.
Abstract: The star network is one of the promising
interconnection networks for future high speed parallel computers, it
is expected to be one of the future-generation networks. The star
network is both edge and vertex symmetry, it was shown to have
many gorgeous topological proprieties also it is owns hierarchical
structure framework. Although much of the research work has been
done on this promising network in literature, it still suffers from
having enough algorithms for load balancing problem. In this paper
we try to work on this issue by investigating and proposing an
efficient algorithm for load balancing problem for the star network.
The proposed algorithm is called Star Clustered Dimension Exchange
Method SCDEM to be implemented on the star network. The
proposed algorithm is based on the Clustered Dimension Exchange
Method (CDEM). The SCDEM algorithm is shown to be efficient in
redistributing the load balancing as evenly as possible among all
nodes of different factor networks.
Abstract: Today’s modern interconnected power system is
highly complex in nature. In this, one of the most important
requirements during the operation of the electric power system is the
reliability and security. Power and frequency oscillation damping
mechanism improve the reliability. Because of power system
stabilizer (PSS) low speed response against of major fault such as
three phase short circuit, FACTs devise that can control the network
condition in very fast time, are becoming popular. But FACTs
capability can be seen in a major fault present when nonlinear models
of FACTs devise and power system equipment are applied. To realize
this aim, the model of multi-machine power system with FACTs
controller is developed in MATLAB/SIMULINK using Sim Power
System (SPS) blockiest. Among the FACTs device, Static
synchronous series compensator (SSSC) due to high speed changes
its reactance characteristic inductive to capacitive, is effective power
flow controller. Tuning process of controller parameter can be
performed using different method. But Genetic Algorithm (GA)
ability tends to use it in controller parameter tuning process. In this
paper firstly POD controller is used to power oscillation damping.
But in this station, frequency oscillation dos not has proper damping
situation. So FOD controller that is tuned using GA is using that
cause to damp out frequency oscillation properly and power
oscillation damping has suitable situation.
Abstract: Laser beam welding for the dissimilar Titanium and
Aluminium thin sheets is an emerging area which is having wider
applications in aerospace, aircraft, automotive, electronics and in
other industries due to its high speed, non-contact, precision with low
heat effects, least welding distortion, low labor costs and convenient
operation. Laser beam welding of dissimilar metal combinations are
increasingly demanded due to high energy densities with small fusion
and heat affected zones. Furthermore, no filler or electrode material is
required and contamination of weld is also very small. The present
study is to reviews the influence of different parameters like laser
power, welding speed, power density, beam diameter, focusing
distance and type of shielding gas on the mechanical properties of
dissimilar metal combinations like SS/Al, Cu/Al and Ti/Al focusing
on aluminum to other materials. Research findings reveal that Ti/Al
combination gives better metallurgical and mechanical properties
than other combinations such as SS/Al and Cu/Al.
Abstract: In this study, a three dimensional numerical heat
transfer model has been used to simulate the laser structuring of
polymer substrate material in the Three-Dimensional Molded
Interconnect Device (3D MID) which is used in the advanced multifunctional
applications. A finite element method (FEM) transient
thermal analysis is performed using APDL (ANSYS Parametric
Design Language) provided by ANSYS. In this model, the effect of
surface heat source was modeled with Gaussian distribution, also the
effect of the mixed boundary conditions which consist of convection
and radiation heat transfers have been considered in this analysis. The
model provides a full description of the temperature distribution, as
well as calculates the depth and the width of the groove upon material
removal at different set of laser parameters such as laser power and
laser speed. This study also includes the experimental procedure to
study the effect of laser parameters on the depth and width of the
removal groove metal as verification to the modeled results. Good
agreement between the experimental and the model results is
achieved for a wide range of laser powers. It is found that the quality
of the laser structure process is affected by the laser scan speed and
laser power. For a high laser structured quality, it is suggested to use
laser with high speed and moderate to high laser power.