Abstract: In mechanical and environmental engineering, mixed
convection is a frequently encountered thermal fluid phenomenon
which exists in atmospheric environment, urban canopy flows, ocean
currents, gas turbines, heat exchangers, and computer chip cooling
systems etc... . This paper deals with a numerical investigation of
mixed convection in a vertical heated channel. This flow results from
the mixing of the up-going fluid along walls of the channel with the
one issued from a flat nozzle located in its entry section. The fluiddynamic
and heat-transfer characteristics of vented vertical channels
are investigated for constant heat-flux boundary conditions, a
Rayleigh number equal to 2.57 1010, for two jet Reynolds number
Re=3 103 and 2104 and the aspect ratio in the 8-20 range. The system
of governing equations is solved with a finite volumes method and an
implicit scheme. The obtained results show that the turbulence and
the jet-wall interaction activate the heat transfer, as does the drive of
ambient air by the jet. For low Reynolds number Re=3 103, the
increase of the aspect Ratio enhances the heat transfer of about 3%,
however; for Re=2 104, the heat transfer enhancement is of about
12%. The numerical velocity, pressure and temperature fields are
post-processed to compute the quantities of engineering interest such
as the induced mass flow rate, and average Nusselt number, in terms
of Rayleigh, Reynolds numbers and dimensionless geometric
parameters are presented.
Abstract: The steady-state temperature for one-dimensional transpiration cooling system has been conducted experimentally and numerically to investigate the heat transfer characteristics of combined convection and radiation. The Nickel –Chrome (Ni-Cr) open-cellular porous material having porosity of 0.93 and pores per inch (PPI) of 21.5 was examined. The upper surface of porous plate was heated by the heat flux of incoming radiation varying from 7.7 - 16.6 kW/m2 whereas air injection velocity fed into the lower surface was varied from 0.36 - 1.27 m/s, and was then rearranged as Reynolds number (Re). For the report of the results in the present study, two efficiencies including of temperature and conversion efficiency were presented. Temperature efficiency indicating how close the mean temperature of a porous heat plate to that of inlet air, and increased rapidly with the air injection velocity (Re). It was then saturated and had a constant value at Re higher than 10. The conversion efficiency, which was regarded as the ability of porous material in transferring energy by convection after absorbed from heat radiation, decreased with increasing of the heat flux and air injection velocity. In addition, it was then asymptotic to a constant value at the Re higher than 10. The numerical predictions also agreed with experimental data very well.
Abstract: In this paper, the feasibility study of using a hybrid
system of ground heat exchangers (GHE) and direct evaporative
cooling system in arid weather condition has been performed. The
model is applied for Yazd and Kerman, two cities with arid weather
condition in Iran. The system composed of three sections: Ground-
Coupled-Circuit (GCC), Direct Evaporative Cooler (DEC) and
Cooling Coil Unite (CCU). The GCC provides the necessary precooling
for DEC. The GCC includes four vertical GHE which are
designed in series configuration. Simulation results show that
hybridization of GCC and DEC could provide comfort condition
whereas DEC alone did not. Based on the results the cooling
effectiveness of a hybrid system is more than unity. Thus, this novel
hybrid system could decrease the air temperature below the ambient
wet-bulb temperature. This environmentally clean and energy
efficient system can be considered as an alternative to the mechanical
vapor compression systems.
Abstract: Ventilation is a fundamental requirement for
occupant health and indoor air quality in buildings. Natural
ventilation can be used as a design strategy in free-running
buildings to:
• Renew indoor air with fresh outside air and lower room
temperatures at times when the outdoor air is cooler.
• Promote air flow to cool down the building structure
(structural cooling).
• Promote occupant physiological cooling processes
(comfort cooling).
This paper focuses on ways in which ventilation can
provide the mechanism for heat dissipation and cooling of the
building structure..It also discusses use of ventilation as a
means of increasing air movement to improve comfort when
indoor air temperatures are too high. The main influencing
factors and design considerations and quantitative guidelines
to help meet the design objectives are also discussed.
Abstract: In contrast to existing methods which do not take into account multiconnectivity in a broad sense of this term, we develop mathematical models and highly effective combination (BIEM and FDM) numerical methods of calculation of stationary and cvazistationary temperature field of a profile part of a blade with convective cooling (from the point of view of realization on PC). The theoretical substantiation of these methods is proved by appropriate theorems. For it, converging quadrature processes have been developed and the estimations of errors in the terms of A.Ziqmound continuity modules have been received. For visualization of profiles are used: the method of the least squares with automatic conjecture, device spline, smooth replenishment and neural nets. Boundary conditions of heat exchange are determined from the solution of the corresponding integral equations and empirical relationships. The reliability of designed methods is proved by calculation and experimental investigations heat and hydraulic characteristics of the gas turbine 1st stage nozzle blade
Abstract: Steady state experiments have been conducted for
natural and mixed convection heat transfer, from five different sized
protruding discrete heat sources, placed at the bottom position on a
PCB and mounted on a vertical channel. The characteristic length (
Lh ) of heat sources vary from 0.005 to 0.011 m. The study has been
done for different range of Reynolds number and modified Grashof
number. From the experiment, the surface temperature distribution
and the Nusselt number of discrete heat sources have been obtained
and the effects of Reynold number and Richardson number on them
have been discussed. The objective is to find the rate of heat
dissipation from heat sources, by placing them at the bottom position
on a PCB and to compare both modes of cooling of heat sources.
Abstract: In order to obtain an accurate result of the heat transfer
of the rib in the internal cooling Rectangular channel, using separation
of variables, analytical solutions of three dimensional steady-state heat
conduction in rectangular ribs are given by solving three dimensional
steady-state function of the rectangular ribs. Therefore, we can get
solution of three dimensional temperature field in the rib. Based on the
solution, we can get how the Bi number affected on heat transfer.
Furthermore, comparisons of the analytical and numerical results
indicate agreement on temperature field in the rib.
Abstract: In this paper a numerical technique is used to predict
the metal temperature of a gas turbine vane. The Rising combustor
exit temperatures in gas turbine engines necessitate active cooling for
the downstream turbine section to avoid thermal failure. This study is
performed the solution of external flow, internal convection, and
conduction within the metal vane. Also the trade-off between the
cooling performances in four different hole shapes and configurations
is performed. At first one of the commonly used cooling hole
geometry is investigated; cylindrical holes and then two other
configurations are simulated. The average temperature magnitude in
mid-plan section of each configuration is obtained and finally the
lower temperature value is selected such as best arrangement.
Abstract: The manufacturing transmission line tower parts has
being generated hazardous waste which is required proper disposal
of waste for protection of land pollution. Manufacturing Process in
the manufacturing of steel angle, plates, pipes, channels are passes
through conventional, semi automatic and CNC machines for
cutting, marking, punching, drilling, notching, bending operations.
All fabricated material Coated with thin layer of Zinc in Galvanizing
plant where molten zinc is used for coating. Prior to Galvanizing,
chemical like 33% concentrated HCl Acid, ammonium chloride and
d-oil being used for pretreatment of iron. The bath of water with
sodium dichromate is used for cooling and protection of the
galvanized steel. For the heating purpose the furnace oil burners are
used. These above process the Zinc dross, Zinc ash, ETP sludge and
waste pickled acid generated as hazardous waste. The RPG has
made captive secured land fill site, since 1997 since then it was
using for disposal of hazardous waste after completion of SLF
(Secured land fill) site. The RPG has raised height from ground
level then now it is being used for disposal of waste as he designed
the SLF after in creasing height of from GL it is functional without
leach ate or adverse impacts in the environment.
Abstract: Nanocrystalline thin film of Na0.1V2O5.nH2O xerogel
obtained by sol gel synthesis was used as gas sensor. Gas sensing
properties of different gases such as hydrogen, petroleum and
humidity were investigated. Applying XRD and TEM the size of the
nanocrystals is found to be 7.5 nm. SEM shows a highly porous
structure with submicron meter-sized voids present throughout the
sample. FTIR measurement shows different chemical groups
identifying the obtained series of gels. The sample was n-type
semiconductor according to the thermoelectric power and electrical
conductivity. It can be seen that the sensor response curves from
130oC to 150oC show a rapid increase in sensitivity for all types of
gas injection, low response values for heating period and the rapid
high response values for cooling period. This result may suggest that
this material is able to act as gas sensor during the heating and
cooling process.
Abstract: In hypersonic environments, the aerothermal effect
makes it difficult for the optical side windows of optical guided
missiles to withstand high heat. This produces cracking or breaking,
resulting in an inability to function. This study used computational
fluid mechanics to investigate the external cooling jet conditions of
optical side windows. The turbulent models k-ε and k-ω were
simulated. To be in better accord with actual aerothermal
environments, a thermal radiation model was added to examine
suitable amounts of external coolants and the optical window
problems of aero-thermodynamics. The simulation results indicate that
when there are no external cooling jets, because airflow on the optical
window and the tail groove produce vortices, the temperatures in these
two locations reach a peak of approximately 1600 K. When the
external cooling jets worked at 0.15 kg/s, the surface temperature of
the optical windows dropped to approximately 280 K. When adding
thermal radiation conditions, because heat flux dissipation was faster,
the surface temperature of the optical windows fell from 280 K to
approximately 260 K. The difference in influence of the different
turbulence models k-ε and k-ω on optical window surface temperature
was not significant.
Abstract: Legionella pneumophila is involved in more than 95%
cases of severe atypical pneumonia. Infection is mainly by
inhalation the indoor aerosols through the water-coolant systems.
Because some Legionella strains may be viable but not culturable,
therefore, Taq polymerase, DNA amplification and semi-nested-PCR
were carried out to detect Legionella-specific 16S-rDNA sequence.
For this purpose, 1.5 litter of water samples from 77 water-coolant
system were collected from four different hospitals, two nursing
homes and one student hostel in Kerman city of Iran, each in a brand
new plastic bottle during summer season of 2006 (from April to
August). The samples were filtered in the sterile condition through
the Millipore Membrane Filter. DNA was extracted from membrane
and used for PCR to detect Legionella spp. The PCR product was
then subjected to semi-nested PCR for detection of L. pneumophila.
Out of 77 water samples that were tested by PCR, 30 (39%) were
positive for most species of Legionella. However, L. pneumophila
was detected from 14 (18.2%) water samples by semi-nested PCR.
From the above results it can be concluded that water coolant
systems of different hospitals and nursing homes in Kerman city of
Iran are highly contaminated with L. pneumophila spp. and pose
serious concern. So, we recommend avoiding such type of coolant
system in the hospitals and nursing homes.
Abstract: Turbine blade cooling is considered as the most
effective way of maintaining high operating temperature making use
of the available materials, and turbine systems with wet compression
have a potential for future power generation because of high efficiency
and high specific power with a relatively low cost. In this paper
performance analysis of wet-compression gas turbine cycle with
turbine blade cooling is carried out. The wet compression process is
analytically modeled based on non-equilibrium droplet evaporation.
Special attention is paid for the effects of pressure ratio and water
injection ratio on the important system variables such as ratio of
coolant fluid flow, fuel consumption, thermal efficiency and specific
power. Parametric studies show that wet compression leads to
insignificant improvement in thermal efficiency but significant
enhancement of specific power in gas turbine systems with turbine
blade cooling.
Abstract: The paper presents the results of microhardness and
microstructure of low carbon steel surface melted using carbon
dioxide laser with a wavelength of 10.6μm and a maximum output
power of 2000W. The processing parameters such as the laser power,
and the scanning rate were investigated in this study. After surface
melting two distinct regions formed corresponding to the melted zone
MZ, and the heat affected zone HAZ. The laser melted region
displayed a cellular fine structures while the HAZ displayed
martensite or bainite structure. At different processing parameters,
the original microstructure of this steel (Ferrite+Pearlite) has been
transformed to new phases of martensitic and bainitic structures. The
fine structure and the high microhardness are evidence of the high
cooling rates which follow the laser melting. The melting pool and
the transformed microstructure in the laser surface melted region of
carbon steel showed clear dependence on laser power and scanning
rate.
Abstract: 98% of the energy needed in Taiwan has been
imported. The prices of petroleum and electricity have been
increasing. In addition, facility capacity, amount of electricity
generation, amount of electricity consumption and number of Taiwan
Power Company customers have continued to increase. For these
reasons energy conservation has become an important topic. In the
past linear regression was used to establish the power consumption
models for chillers. In this study, grey prediction is used to evaluate
the power consumption of a chiller so as to lower the total power
consumption at peak-load (so that the relevant power providers do not
need to keep on increasing their power generation capacity and facility
capacity).
In grey prediction, only several numerical values (at least four
numerical values) are needed to establish the power consumption
models for chillers. If PLR, the temperatures of supply chilled-water
and return chilled-water, and the temperatures of supply cooling-water
and return cooling-water are taken into consideration, quite accurate
results (with the accuracy close to 99% for short-term predictions)
may be obtained. Through such methods, we can predict whether the
power consumption at peak-load will exceed the contract power
capacity signed by the corresponding entity and Taiwan Power
Company. If the power consumption at peak-load exceeds the power
demand, the temperature of the supply chilled-water may be adjusted
so as to reduce the PLR and hence lower the power consumption.
Abstract: The compression-absorption heat pump (C-A HP), one
of the promising heat recovery equipments that make process hot
water using low temperature heat of wastewater, was evaluated by
computer simulation. A simulation program was developed based on
the continuity and the first and second laws of thermodynamics. Both
the absorber and desorber were modeled using UA-LMTD method. In
order to prevent an unfeasible temperature profile and to reduce
calculation errors from the curved temperature profile of a mixture,
heat loads were divided into lots of segments. A single-stage
compressor was considered. A compressor cooling load was also
taken into account. An isentropic efficiency was computed from the
map data. Simulation conditions were given based on the system
consisting of ordinarily designed components. The simulation results
show that most of the total entropy generation occurs during the
compression and cooling process, thus suggesting the possibility that
system performance can be enhanced if a rectifier is introduced.
Abstract: Shape memory alloy (SMA) actuators have found a
wide range of applications due to their unique properties such as high
force, small size, lightweight and silent operation. This paper presents
the development of compact (SMA) actuator and cooling system in
one unit. This actuator is developed for multi-fingered hand. It
consists of nickel-titanium (Nitinol) SMA wires in compact forming.
The new arrangement insulates SMA wires from the human body by
housing it in a heat sink and uses a thermoelectric device for rejecting
heat to improve the actuator performance. The study uses
optimization methods for selecting the SMA wires geometrical
parameters and the material of a heat sink. The experimental work
implements the actuator prototype and measures its response.
Abstract: This study describes a capillary-based device
integrated with the heating and cooling modules for polymerase chain
reaction (PCR). The device consists of the reaction
polytetrafluoroethylene (PTFE) capillary, the aluminum blocks, and is
equipped with two cartridge heaters, a thermoelectric (TE) cooler, a
fan, and some thermocouples for temperature control. The cartridge
heaters are placed into the heating blocks and maintained at two
different temperatures to achieve the denaturation and the extension
step. Some thermocouples inserted into the capillary are used to obtain
the transient temperature profiles of the reaction sample during
thermal cycles. A 483-bp DNA template is amplified successfully in
the designed system and the traditional thermal cycler. This work
should be interesting to persons involved in the high-temperature
based reactions and genomics or cell analysis.
Abstract: The performances of a thermoacoustic travelling-wave
refrigerator are presented. Developed in the frame of the European
project called THATEA, it is designed for providing 600 W at a
temperature of 233 K with an efficiency of 40 % relative to the
Carnot efficiency. This paper presents the device and the results of
the first measurements. For a cooling power of 210 W, a coefficient
of performance relative to Carnot of 30 % is achieved when the
refrigerator is coupled with an existing standing-wave engine.
Abstract: The work presented in this study is related to an
energy system analysis based on passive cooling system for
dwellings. It consists to solar chimney energy performances
determination versus geometrical and environmental considerations
as the size and inlet width conditions of the chimney. Adrar site
located in the southern region of Algeria is chosen for this study
according to ambient temperature and solar irradiance technical data
availability. Obtained results are related to the glazing temperature
distributions, the chimney air flow and internal wall temperatures.
The air room change per hour (ACH) parameter, the outlet air
velocity and mass air flow rate are also determined. It is shown that
the chimney width has a significant effect on energy performances
compared to its entry size. A good agreement is observed between
these results and those obtained by others from the literature.