Abstract: This paper presents a comparative analysis of
continuously stirred tank reactor (CSTR) control based on adaptive
control and optimal tuning of PID control based on particle swarm
optimization. In the design of adaptive control, Model reference
adaptive control (MRAC) scheme is used, in which the adaptation
law have been developed by MIT rule & Lyapunov’s rule. In PSO
control parameters of PID controller is tuned by using the concept of
particle swarm optimization to get optimized operating point for
minimum integral square error (ISE) condition. The results show the
adjustment of PID parameters converting into the optimal operating
point and the good control response can be obtained by the PSO
technique.
Abstract: The subject of this paper is to review, comparative
analysis and simulation of selected components of power electronic
systems (PES), consistent with the concept of a more electric aircraft
(MEA). Comparative analysis and simulation in software
environment MATLAB / Simulink were carried out on the base of a
group of representatives of civil aircraft (B-787, A-380) and military
(F-22 Raptor, F-35) in the context of multi-pulse converters used in
them (6- and 12-pulse, and 18- and 24-pulse), which are key
components of high-tech electronics on-board power systems of
autonomous power systems (ASE) of modern aircraft (airplanes of
the future).
Abstract: This paper presents comparative analysis of
photovoltaic systems (PVS) and propose practical techniques to
improve operational efficiency of the PVS. The best engineering and
construction practices for PVS are identified and field oriented
recommendation are made. Comparative analysis of central and
string inverter based, as well as 600 and 1000VDC PVS are
performed. In addition, direct current (DC) and alternating current
(AC) photovoltaic (PV) module based systems are compared.
Comparison shows that 1000V DC String Inverters based PVS is the
best choice.
Abstract: Comparative analysis of the properties of melon seed,
coconut fruit and their oil yield were evaluated in this work using
standard analytical technique AOAC. The results of the analysis
carried out revealed that the moisture contents of the samples studied
are 11.15% (melon) and 7.59% (coconut). The crude lipid content are
46.10% (melon) and 55.15% (coconut).The treatment combinations
used (leaching time, leaching temperature and solute: solvent ratio)
showed significant difference (p < 0.05) in yield between the
samples, with melon oil seed flour having a higher percentage range
of oil yield (41.30 – 52.90%) and coconut (36.25 – 49.83%). The
physical characterization of the extracted oil was also carried out.
The values gotten for refractive index are 1.487 (melon seed oil) and
1.361 (coconut oil) and viscosities are 0.008 (melon seed oil) and
0.002 (coconut oil). The chemical analysis of the extracted oils shows
acid value of 1.00mg NaOH/g oil (melon oil), 10.050mg NaOH/g oil
(coconut oil) and saponification value of 187.00mg/KOH (melon oil)
and 183.26mg/KOH (coconut oil). The iodine value of the melon oil
gave 75.00mg I2/g and 81.00mg I2/g for coconut oil. A standard
statistical package Minitab version 16.0 was used in the regression
analysis and analysis of variance (ANOVA). The statistical software
mentioned above was also used to optimize the leaching process.
Both samples gave high oil yield at the same optimal conditions. The
optimal conditions to obtain highest oil yield ≥ 52% (melon seed)
and ≥ 48% (coconut seed) are solute - solvent ratio of 40g/ml,
leaching time of 2hours and leaching temperature of 50oC. The two
samples studied have potential of yielding oil with melon seed giving
the higher yield.
Abstract: In the present paper the design of plate heat exchangers
is formulated as an optimization problem considering two
mathematical modelling. The number of plates is the objective
function to be minimized, considering implicitly some parameters
configuration. Screening is the optimization method used to solve the
problem. Thermal and hydraulic constraints are verified, not viable
solutions are discarded and the method searches for the convergence to
the optimum, case it exists. A case study is presented to test the
applicability of the developed algorithm. Results show coherency with
the literature.
Abstract: In addition to the advantages of light weight, resistant
corrosion and ease of processing, aluminum is also applied to the
long-span spatial structures. However, the elastic modulus of
aluminum is lower than that of the steel. This paper combines the
high performance aluminum honeycomb panel with the aluminum
latticed shell, forming a new panel-and-rod composite shell structure.
Through comparative analysis between the static and dynamic
performance, the conclusion that the structure of composite shell is
noticeably superior to the structure combined before.
Abstract: The paper provides a comprehensive analysis of the
sustainable development in the Belgrade Metropolitan Region - BMA
(level NUTS 2) preliminary evaluating the three chosen components:
1) economic growth and developmental changes; 2) competitiveness;
and 3) territorial concentration and industrial specialization. First, we
identified the main results of development changes and economic
growth by applying Shift-share analysis on the metropolitan level.
Second, the empirical evaluation of competitiveness in the BMA is
based on the analysis of absolute and relative values of eight
indicators by Spider method. Paper shows that the consideration of
the national share, industrial mix and metropolitan/regional share in
total Shift share of the BMA, as well as economic/functional
specialization of the BMA indicate very strong process of
deindustrialization. Allocative component of the BMA economic
growth has positive value, reflecting the above-average sector
productivity compared to the national average. Third, the important
positive role of metropolitan/regional component in decomposition of
the BMA economic growth is highlighted as one of the key results.
Finally, comparative analysis of the industrial territorial
concentration in the BMA in relation to Serbia is based on location
quotient (LQ) or Balassa index as a valid measure. The results
indicate absolute and relative differences in decrease of industry
territorial concentration as well as inefficiency of utilizing territorial
capital in the BMA. Results are important for the increase of regional
competitiveness and territorial distribution in this area as well as for
improvement of sustainable metropolitan and sector policies,
planning and governance on this level.
Abstract: Given the limited research on Small and Mediumsized
Enterprises’ (SMEs) contribution to Corporate Social
Responsibility (CSR) and even scarcer research on Swiss SMEs, this
paper helps to fill these gaps by enabling the identification of supranational
SME parameters. Thus, the paper investigates the current
state of SME practices in Switzerland and across 15 other countries.
Combining the degree to which SMEs demonstrate an explicit (or
business case) approach or see CSR as an implicit moral activity with
the assessment of their attributes for “variety of capitalism” defines
the framework of this comparative analysis. To outline Swiss small
business CSR patterns in particular, 40 SME owner-managers were
interviewed. A secondary data analysis of studies from different
countries laid groundwork for this comparative overview of small
business CSR. The paper identifies Swiss small business CSR as
driven by norms, values, and by the aspiration to contribute to
society, thus, as an implicit part of the day-to-day business. Similar to
most Central European, Mediterranean, Nordic, and Asian countries,
explicit CSR is still very rare in Swiss SMEs. Astonishingly, also
British and American SMEs follow this pattern in spite of their strong
and distinctly liberal market economies. Though other findings show
that nationality matters this research concludes that SME culture and
an informal CSR agenda are strongly formative and superseding even
forces of market economies, nationally cultural patterns, and
language. Hence, classifications of countries by their market system,
as found in the comparative capitalism literature, do not match the
CSR practices in SMEs as they do not mirror the peculiarities of their
business. This raises questions on the universality and
generalisability of unmediated, explicit management concepts,
especially in the context of small firms.
Abstract: The article represents the results of clinical researches
of composite herbal medicinal product based on essential oils of
Sedum plants growing in Kazakhstan in commercial reserves at the
territory of Kazakhstan. The results of comparative analysis are
represented in obstetric-gynecologic practice during combined
therapy for postnatal complications, inflammatory infiltrates in the
area of surgical wounds including wounds after caesarean section.
Abstract: Robotics brings together several very different
engineering areas and skills. There are various types of robot such as
humanoid robot, mobile robots, remotely operated vehicles, modern
autonomous robots etc. This survey paper advocates the operation of a
robotic car (remotely operated vehicle) that is controlled by a mobile
phone (communicate on a large scale over a large distance even from
different cities). The person makes a call to the mobile phone placed
in the car. In the case of a call, if any one of the button is pressed, a
tone equivalent to the button pressed is heard at the other end of the
call. This tone is known as DTMF (Dual Tone Multiple Frequency).
The car recognizes this DTMF tone with the help of the phone stacked
in the car. The received tone is processed by the Arduino
microcontroller. The microcontroller is programmed to acquire a
decision for any given input and outputs its decision to motor drivers
in order to drive the motors in the forward direction or backward
direction or left or right direction. The mobile phone that makes a call
to cell phone stacked in the car act as a remote.
Abstract: This paper proposes five level diode clamped Z source
Inverter. The existing PWM techniques used for ZSI are restricted for
two level. The two level Z Source Inverter have high harmonic
distortions which effects the performance of the grid connected PV
system. To improve the performance of the system the number of
voltage levels in the output waveform need to be increased. This
paper presents comparative analysis of a five level diode clamped Z
source Inverter with different carrier based Modified Pulse Width
Modulation techniques. The parameters considered for comparison
are output voltage, voltage gain, voltage stress across switch and total
harmonic distortion when powered by same DC supply. Analytical
results are verified using MATLAB.
Abstract: Comparing other methods of waste water treatment,
constructed wetlands are one of the most fascinating practices
because being a natural process they are eco-friendly have low
construction and maintenance cost and have considerable capability
of wastewater treatment. The current research was focused mainly on
comparison of Ranunculus muricatus and Typha latifolia as wetland
plants for domestic wastewater treatment by designing and
constructing efficient pilot scale horizontal subsurface flow
mesocosms. Parameters like chemical oxygen demand, biological
oxygen demand, phosphates, sulphates, nitrites, nitrates, and
pathogenic indicator microbes were studied continuously with
successive treatments. Treatment efficiency of the system increases
with passage of time and with increase in temperature. Efficiency of
T. latifolia planted setups in open environment was fairly good for
parameters like COD and BOD5 which was showing reduction up to
82.5% for COD and 82.6% for BOD5 while DO was increased up to
125%. Efficiency of R. muricatus vegetated setup was also good but
lowers than that of T. latifolia planted showing 80.95% removal of
COD and BOD5. Ranunculus muricatus was found effective in
reducing bacterial count in wastewater. Both macrophytes were
found promising in wastewater treatment.
Abstract: Presently, it is necessary to ensure the sustainable
development of passenger and freight transport. Increasing
performance of road freight has had a negative impact to environment
and society. It is therefore necessary to increase the competitiveness
of intermodal transport, which is more environmentally friendly. The
study describes the effectiveness of logistical centers realization for
companies and society and research how the partial internalization of
external costs reflected in the efficient use of these centers and
increase the competitiveness of intermodal transport to road freight.
In our research, we use the method of comparative analysis and
market research to describe the advantages of logistic centers for their
users as well as for society as a whole. Method normal costing is used
for calculation infrastructure and total costs, method of conversion
costing for determine the external costs. We modelled total society
costs for road freight transport and inter modal transport chain (we
assumed that most of the traffic is carried by rail) with different
loading schemes for condition in the Slovak Republic. Our research
has shown that higher utilization of inter modal transport chain do
good not only for society, but for companies providing freight
services too. Increase in use of inter modal transport chain can bring
many benefits to society that do not bring direct immediate financial
return. They often bring the multiplier effects, such as greater use of
environmentally friendly transport mode and reduce the total society
costs.
Abstract: This paper deals with current strategic challenges
related to the reshaping of the basic conditions of corporate operations.
Through the experimental analysis of some domestic corporations, it
presents how and to what extent Hungarian corporations are prepared
for the current strategic challenges. The study examines how strategic
directions and answer opportunities have changed in the following
interrelated areas in the past five years: economic globalization,
corporate sustainability, IT applications, labor force diversity and
ethical competences. The conclusions of the empirical survey give a
reliable basis on which economic organizations and enterprises can
formulate their strategy.
Abstract: Fluid viscous damping systems are well suited for
many air vehicles subjected to shock and vibration. These damping
system work with the principle of viscous fluid throttling through the
orifice to create huge pressure difference between compression and
rebound chamber and obtain the required damping force. One
application of such systems is its use in aircraft door system to
counteract the door’s velocity and safely stop it. In exigency
situations like crash or emergency landing where the door doesn’t
open easily, possibly due to unusually tilting of fuselage or some
obstacles or intrusion of debris obstruction to move the parts of the
door, such system can be combined with other systems to provide
needed force to forcefully open the door and also securely stop it
simultaneously within the required time i.e. less than 8 seconds. In
the present study, a hydraulic system called snubber along with other
systems like actuator, gas bottle assembly which together known as
emergency power assist system (EPAS) is designed, built and
experimentally studied to check the magnitude of angular velocity,
damping force and time required to effectively open the door.
Whenever needed, the gas pressure from the bottle is released to
actuate the actuator and at the same time pull the snubber’s piston to
operate the emergency opening of the door. Such EPAS installed in
the suspension arm of the aircraft door is studied explicitly changing
parameters like orifice size, oil level, oil viscosity and bypass valve
gap and its spring of the snubber at varying temperature to generate
the optimum design case. Comparative analysis of the EPAS at
several cases is done and conclusions are made. It is found that
during emergency condition, the system opening time and angular
velocity, when snubber with 0.3mm piston and shaft orifice and
bypass valve gap of 0.5 mm with its original spring is used, shows
significant improvement over the old ones.
Abstract: Comparisons of financial development across
countries are central to answering many of the questions on factors
leading to economic development. For this reason this study analyzes
the implications of financial system’s development on country’s
economic development. The aim of the article: to analyze the impact
of financial system’s development on economic development. The
following research methods were used: systemic, logical and
comparative analysis of scientific literature, analysis of statistical
data, time series model (Autoregressive Distributed Lag (ARDL)
Model). The empirical results suggest about positive short and long
term effect of stock market development on GDP per capita.
Abstract: The tombolo of Giens is located in the town of Hyères
(France). We recall the history of coastal erosion, and prominent
factors affecting the evolution of the western tombolo. We then
discuss the possibility of stabilizing the western tombolo. Our
argumentation relies on a coupled model integrating swells, currents,
water levels and sediment transport. We present the conclusions of
the simulations of various scenarios, including pre-existing
propositions from coastal engineering offices. We conclude that
beach replenishment seems to be necessary but not sufficient for the
stabilization of the beach. Breakwaters reveal effective particularly in
the most exposed northern area. Some solutions fulfill conditions so
as to be elected as satisfactory. We give a comparative analysis of the
efficiency of 14 alternatives for the protection of the tombolo.
Abstract: This paper designs the four-phase Boost Converter
which overcomes the problem of high input ripple current and output
ripple voltage. Digital control is more convenient for such a topology
on basis of synchronization, phase shift operation, etc. Simulation
results are presented for open-loop and closed-loop for four phase
boost converter. This control scheme is applicable for PFC rectifiers
as well. Thus a comparative analysis based on the obtained results is
performed.
Abstract: Search engine plays an important role in internet, to
retrieve the relevant documents among the huge number of web
pages. However, it retrieves more number of documents, which are
all relevant to your search topics. To retrieve the most meaningful
documents related to search topics, ranking algorithm is used in
information retrieval technique. One of the issues in data miming is
ranking the retrieved document. In information retrieval the ranking
is one of the practical problems. This paper includes various Page
Ranking algorithms, page segmentation algorithms and compares
those algorithms used for Information Retrieval. Diverse Page Rank
based algorithms like Page Rank (PR), Weighted Page Rank (WPR),
Weight Page Content Rank (WPCR), Hyperlink Induced Topic
Selection (HITS), Distance Rank, Eigen Rumor, Distance Rank Time
Rank, Tag Rank, Relational Based Page Rank and Query Dependent
Ranking algorithms are discussed and compared.
Abstract: Nowadays, the Web has become one of the most
pervasive platforms for information change and retrieval. It collects
the suitable and perfectly fitting information from websites that one
requires. Data mining is the form of extracting data’s available in the
internet. Web mining is one of the elements of data mining
Technique, which relates to various research communities such as
information recovery, folder managing system and simulated
intellects. In this Paper we have discussed the concepts of Web
mining. We contain generally focused on one of the categories of
Web mining, specifically the Web Content Mining and its various
farm duties. The mining tools are imperative to scanning the many
images, text, and HTML documents and then, the result is used by
the various search engines. We conclude by presenting a comparative
table of these tools based on some pertinent criteria.