Abstract: This paper presents the experimental results of
comparison between leakage currents and discharge currents. The leakage currents were obtained on polluted porcelain insulator.
Whereas, the discharge currents were obtained on lightly artificial
polluted porcelain specimen. The conducted measurements were
leakage current or discharge current and applied voltage. The insulator or specimen was in a hermetically sealed chamber, and the
current waveforms were analyzed using FFT.
The result indicated that the leakage current (LC) on low RH condition the fifth harmonic would be visible, and followed by the
seventh harmonic. The insulator had capacitive property. Otherwise,
on 99% relative humidity, the fifth harmonic would also be visible,
and the phase angle reached up to 12.2 degree. Whereas, on discharge current, the third harmonic would be visible, and followed
by fifth harmonic. The third harmonic would increase as pressure reduced. On this condition, the specimen had a non-linear characteristics
Abstract: The seismic vulnerability of an urban area is of a great
deal for local authorities especially those facing earthquakes. So, it is
important to have an efficient tool to assess the vulnerability of
existing buildings. The use of the VIP (Vulnerability Index Program)
and the GIS (Geographic Information System) let us to identify the
most vulnerable districts of an urban area.
The use of the vulnerability index method lets us to assess the
vulnerability of the center town of Blida (Algeria) which is a
historical town and which has grown enormously during the last
decades. In this method, three levels of vulnerability are defined. The
GIS has been used to build a data base in order to perform different
thematic analyses. These analyses show the seismic vulnerability of
Blida.
Abstract: In this document we studied more in detail the Performances of the vertical handover in the networks WLAN, WiMAX, UMTS before studying of it the Procedure of Handoff Vertical, the whole buckled by simulations putting forward the performances of the handover in the heterogeneous networks. The goal of Vertical Handover is to carry out several accesses in real-time in the heterogeneous networks. This makes it possible a user to use several networks (such as WLAN UMTS andWiMAX) in parallel, and the system to commutate automatically at another basic station, without disconnecting itself, as if there were no cut and with little loss of data as possible.
Abstract: The fluorescent pseudomonad strain R81 is a root
colonizing rhizobacteria which promotes the growth of many plants
by various mechanisms. Its broth containing siderophore (ironchelating
compound) and 2,4- diacetyl phloroglucinol (DAPG) is
used for preparing bioinoculant formulations for agronomical
applications. Glycerol was found to be the best carbon source for
improved biomass production. Splitting of nitrogen source to NH4Cl
and urea had a stabilizing effect on pH during batch cultivation. Ltryptophan
at 0.5 % in the medium increased the siderophore
production to 850 mg/l. During batch cultivation of the strain in a
bioreactor, a maximum of 4 g/l of dry cell mass, 1.8 g/l of
siderophore and 20 mg/l of DAPG was achieved when glycerol was
15 g/l and C/N ratio was maintained at 12.5. In case of intermittent
feeding of fresh medium during fed-batch cultivation, the dry cell
mass was increased to 25 g/l with improved production of DAPG to
70 mg/l.
Abstract: Dengue fever has become a major concern for health
authorities all over the world particularly in the tropical countries.
These countries, in particular are experiencing the most worrying
outbreak of dengue fever (DF) and dengue haemorrhagic fever
(DHF). The DF and DHF epidemics, thus, have become the main
causes of hospital admissions and deaths in Malaysia. This paper,
therefore, attempts to examine the environmental factors that may
influence the recent dengue outbreak. The aim of this study is twofold,
firstly is to establish a statistical model to describe the
relationship between the number of dengue cases and a range of
explanatory variables and secondly, to identify the lag operator for
explanatory variables which affect the dengue incidence the most.
The explanatory variables involved include the level of cloud cover,
percentage of relative humidity, amount of rainfall, maximum
temperature, minimum temperature and wind speed. The Poisson and
Negative Binomial regression analyses were used in this study. The
results of the analyses on the 915 observations (daily data taken from
July 2006 to Dec 2008), reveal that the climatic factors comprising of
daily temperature and wind speed were found to significantly
influence the incidence of dengue fever after 2 and 3 weeks of their
occurrences. The effect of humidity, on the other hand, appears to be
significant only after 2 weeks.
Abstract: This study aims to assess the vulnerability and risk of
the coastal areas of Taijiang to abnormal oceanographic phenomena.
In addition, this study aims to investigate and collect data regarding
the disaster losses, land utilization, and other social, economic, and
environmental issues in these coastal areas to construct a coastal
vulnerability and risk map based on the obtained climate-change risk
assessment results. Considering the indexes of the three coastal
vulnerability dimensions, namely, man-made facilities, environmental
geography, and social economy, this study adopted the equal
weighting process and Analytic Hierarchy Process to analyze the
vulnerability of these coastal areas to disasters caused by climatic
changes. Among the areas with high coastal vulnerability to climatic
changes, three towns had the highest coastal vulnerability and four had
the highest relative vulnerability. Areas with lower disaster risks were
found to be increasingly vulnerable to disasters caused by climatic
changes as time progresses.
Abstract: Technical laboratories are typically considered as
highly hazardous places in the polytechnic institution when
addressing the problems of high incidences and fatality rates. In
conjunction with several topics covered in the technical curricular,
safety and health precaution should be highlighted in order to
connect to few key ideas of being safe. Therefore the assessment of
safety awareness in terms of safety and health about hazardous and
risks at laboratories is needed and has to be incorporated with
technical education and other training programmes. The purpose of
this study was to determine the efficacy of technical laboratory safety
in one of the polytechnics in northern region. The study examined
three related issues that were; the availability of safety material and
equipment, safety practice adopted by technical teachers and
administrator-s safety attitudes in enforcing safety to the students. A
model of efficacy technical laboratory was developed to test the
linear relationship between existing safety material and equipment,
teachers- safety practice and administrators- attitude in enforcing
safety and to identify which of technical laboratory safety issues was
the most pertinent factor to realize safety in technical laboratory.
This was done by analyzing survey-based data sets particularly those
obtained from samples of 210 students in the polytechnic. The
Pearson Correlation was used to measure the association between the
variables and to test the research hypotheses. The result of the study
has found that there was a significant correlation between existing
safety material and equipment, safety practice adopted by teacher
and administrator-s attitude. There was also a significant relationship
between technical laboratory safety and safety practice adopted by
teacher and between technical laboratory safety and administrator
attitude. Hence, safety practice adopted by teacher and administrator
attitude is vital in realizing technical laboratory safety.
Abstract: In the current study we present a system that is
capable to deliver proxy based differentiated service. It will help the
carrier service node to sell a prepaid service to clients and limit the
use to a particular mobile device or devices for a certain time. The
system includes software and hardware architecture for a mobile
device with moderate computational power, and a secure protocol for
communication between it and its carrier service node. On the
carrier service node a proxy runs on a centralized server to be
capable of implementing cryptographic algorithms, while the mobile
device contains a simple embedded processor capable of executing
simple algorithms. One prerequisite is needed for the system to run
efficiently that is a presence of Global Trusted Verification Authority
(GTVA) which is equivalent to certifying authority in IP networks.
This system appears to be of great interest for many commercial
transactions, business to business electronic and mobile commerce,
and military applications.
Abstract: In this paper, many techniques for blind identification of moving average (MA) process are presented. These methods utilize third- and fourth-order cumulants of the noisy observations of the system output. The system is driven by an independent and identically distributed (i.i.d) non-Gaussian sequence that is not observed. Two nonlinear optimization algorithms, namely the Gradient Descent and the Gauss-Newton algorithms are exposed. An algorithm based on the joint-diagonalization of the fourth-order cumulant matrices (FOSI) is also considered, as well as an improved version of the classical C(q, 0, k) algorithm based on the choice of the Best 1-D Slice of fourth-order cumulants. To illustrate the effectiveness of our methods, various simulation examples are presented.
Abstract: Using bottom-up image processing algorithms to predict human eye fixations and extract the relevant embedded information in images has been widely applied in the design of active machine vision systems. Scene text is an important feature to be extracted, especially in vision-based mobile robot navigation as many potential landmarks such as nameplates and information signs contain text. This paper proposes an edge-based text region extraction algorithm, which is robust with respect to font sizes, styles, color/intensity, orientations, and effects of illumination, reflections, shadows, perspective distortion, and the complexity of image backgrounds. Performance of the proposed algorithm is compared against a number of widely used text localization algorithms and the results show that this method can quickly and effectively localize and extract text regions from real scenes and can be used in mobile robot navigation under an indoor environment to detect text based landmarks.
Abstract: The main objective of this paper is a comparative
investigate in enhancement of damping power system oscillation via
coordinated design of the power system stabilizer (PSS) and static
synchronous series compensator (SSSC) and static synchronous
compensator (STATCOM). The design problem of FACTS-based
stabilizers is formulated as a GA based optimization problem. In this
paper eigenvalue analysis method is used on small signal stability of
single machine infinite bus (SMIB) system installed with SSSC and
STATCOM. The generator is equipped with a PSS. The proposed
stabilizers are tested on a weakly connected power system with
different disturbances and loading conditions. This aim is to enhance
both rotor angle and power system stability. The eigenvalue analysis
and non-linear simulation results are presented to show the effects of
these FACTS-based stabilizers and reveal that SSSC exhibits the best
effectiveness on damping power system oscillation.
Abstract: This paper proposes a modeling method of the laws controlling manufacturing systems with temporal and non temporal constraints. A methodology of robust control construction generating the margins of passive and active robustness is being elaborated. Indeed, two paramount models are presented in this paper. The first utilizes the P-time Petri Nets which is used to manage the flow type disturbances. The second, the quality model, exploits the Intervals Constrained Petri Nets (ICPN) tool which allows the system to preserve its quality specificities. The redundancy of the robustness of the elementary parameters between passive and active is also used. The final model built allows the correlation of temporal and non temporal criteria by putting two paramount models in interaction. To do so, a set of definitions and theorems are employed and affirmed by applicator examples.
Abstract: This paper addresses integration issues in supply
chain, and tries to investigate how different aspects of integration are
linked with some product features. Integration in this study is
interpreted as "internal", "upstream" (supply), and "downstream"
(demand). Two features of product innovative and quality are
considered. To examine the relationships between supply chain
integrations – as mentioned above, and product features, this research
follows the survey method in automotive industry.The results imply
that supply chain upstream integration has a higher impact on product
quality, comparing to internal and supply chain downstream
integrations. It is also found that the influence of supply chain
downstream integration on product innovation is greater than other
variables. In brief, this study mainly tackles the importance of
specific level of supply chain integrations and its effects on two
product features.
Abstract: This study assessed the effects of climate change on
Thai soybeans under simulation situations. Our study is focused on
temperature variability and effects on growth, yield, and genetic
changes in 2 generations of Chiang Mai 60 cultivars. In the
experiment, soybeans were exposed to 3 levels of air temperature for
8 h day-1 in an open top chamber for 2 cropping periods. Air
temperature levels in each treatment were controlled at 30-33°C (±
2.3) for LT-treatment, 33-36°C ( ± 2.4) for AT-treatment, and 36-40
°C ( ± 3.2) for HT-treatment, respectively. Positive effects of high
temperature became obvious at the maturing stage when yield
significantly increased in both cropping periods. Results in growth
indicated that shoot length at the pre-maturing stage
(V3-R3) was more positively affected by high temperature than at the
maturing stage. However, the positive effect on growth under high
temperature was not found in the 2nd cropping period. Finally, genetic
changes were examined in phenotype characteristics by the AFLPs
technique. The results showed that the high temperature factor clearly
caused genetic change in the soybeans and showed more alteration in
the 2nd cropping period.
Abstract: Research results and optimal parameters investigation
of laser cut and profiling of diamond and quartz substrates by
femtosecond laser pulses are presented. Profiles 10 μm in width, ~25
μm in depth and several millimeters long were made. Investigation of
boundaries quality has been carried out with the use of AFM
«Vecco». Possibility of technological formation of profiles and
micro-holes in diamond and quartz substrates with nanometer-scale
boundaries is shown. Experimental results of multilayer dielectric
cover treatment are also presented. Possibility of precise upper layer
(thickness of 70–140 nm) removal is demonstrated. Processes of thin
metal film (60 nm and 350 nm thick) treatment are considered.
Isolation tracks (conductance ~ 10-11 S) 1.6–2.5 μm in width in
conductive metal layers are formed.
Abstract: The paper describes the workings for four models of
CONWIP systems used till date; the basic CONWIP system, the
hybrid CONWIP system, the multi-product CONWIP system, and the
parallel CONWIP system. The final novel model is introduced in this
paper in a general form. These models may be adopted for analysis
for both simulation studies and implementation on the shop floor. For
each model, input parameters of interest are highlighted and their
impacts on several system performance measures are addressed.
Abstract: We investigate the sufficient condition under which each positive b-weakly compact operator is Dunford-Pettis. We also investigate the necessary condition on which each positive b-weakly compact operator is Dunford-Pettis. Necessary condition on which each positive b-weakly compact operator is weakly compact is also considered. We give the operator that is semi-compact, but it is not bweakly. We present a necessary and sufficient condition under which each positive semi-compact operator is b-weakly compact.
Abstract: Monoculture and mixed cultures of microalgae and
the oleaginous yeast for microbial oil productions were investigated
using sugarcane juice as carbon substrate. The monoculture of yeast
Torulaspora maleeae Y30, Torulaspora globosa YU5/2 grew faster
than that of microalgae Chlorella sp. KKU-S2. In monoculture of T.
maleeae Y30, a biomass of 8.267g/L with lipid yield of 0.920g/L
were obtained, while 8.333g/L of biomass with lipid yield of
1.141g/L were obtained for monoculture of T. globosa YU5/2. A
biomass of 1.933g/L with lipid yield of 0.052g/L was found for
monoculture of Chlorella sp. KKU-S2. The biomass concentration in
the mixed culture of the oleaginous yeast with microalgae increased
faster and was higher compared with that in the monocultures. A
biomass of 8.733g/L with lipid yield of 1.564g/L was obtained for a
mixed culture of T. maleeae Y30 with Chlorella sp. KKU-S2, while
8.010g/L of biomass with lipid yield of 2.424g/L was found for
mixed culture of T. globosa YU5/2 with Chlorella sp. KKU-S2.
Maximum cell yield coefficient (YX/S, g/L) was found of 0.323 in
monoculture of Chlorella sp. KKU-S2 but low level of both specific
yield of lipid (YP/X, g lipid/g cells) of 0.027 and volumetric lipid
production rate (QP, g/L/d) of 0.003 were observed. While, maximum
YP/X (0.303), QP (0.105) and maximum process product yield (YP/S,
0.061) were obtained in mixed culture of T. globosa YU5/2 with
Chlorella sp. KKU-S2. The results obtained from the study shows
that mixed culture of yeast with microalgae is a desirable cultivation
process for microbial oil production.
Abstract: The running logs of a process hold valuable
information about its executed activity behavior and generated activity
logic structure. Theses informative logs can be extracted, analyzed and
utilized to improve the efficiencies of the process's execution and
conduction. One of the techniques used to accomplish the process
improvement is called as process mining. To mine similar processes is
such an improvement mission in process mining. Rather than directly
mining similar processes using a single comparing coefficient or a
complicate fitness function, this paper presents a simplified heuristic
process mining algorithm with two similarity comparisons that are
able to relatively conform the activity logic sequences (traces) of
mining processes with those of a normalized (regularized) one. The
relative process conformance is to find which of the mining processes
match the required activity sequences and relationships, further for
necessary and sufficient applications of the mined processes to process
improvements. One similarity presented is defined by the relationships
in terms of the number of similar activity sequences existing in
different processes; another similarity expresses the degree of the
similar (identical) activity sequences among the conforming processes.
Since these two similarities are with respect to certain typical behavior
(activity sequences) occurred in an entire process, the common
problems, such as the inappropriateness of an absolute comparison and
the incapability of an intrinsic information elicitation, which are often
appeared in other process conforming techniques, can be solved by the
relative process comparison presented in this paper. To demonstrate
the potentiality of the proposed algorithm, a numerical example is
illustrated.
Abstract: This paper presents the experimental results of silicone rubber housing material for 24kV lightning arrester under artificial accelerated ageing test based on IEC 61109 specifications. Specimens having inclined and alternated shed made of HTV silicone rubber with ATH content and having leakage distance 625 mm were tested continuously 1000 hrs in artificial salt fog chamber. After 1000 hrs of salt fog ageing test, obviously surface erosion was observed on trunk between the upper large shed and the lower small shed near the energized end. Decreasing in hydrophobicity and increasing in hardness were measured on tested specimen comparing with new specimen. Chemical analysis by ATR-FTIR confirmed the observation results.