Abstract: In this paper, a numerical study has been made to
analyze the transient 2-D flows of a viscous incompressible fluid
through channels with forward or backward constriction. Problems
addressed include flow through sudden contraction and sudden
expansion channel geometries with rounded and increasingly sharp
reentrant corner. In both the cases, numerical results are presented for
the separation and reattachment points, streamlines, vorticity and
flow patterns. A fourth order accurate compact scheme has been
employed to efficiently capture steady state solutions of the
governing equations. It appears from our study that sharpness of the
throat in the channel is one of the important parameters to control the
strength and size of the separation zone without modifying the
general flow patterns. The comparison between the two cases shows
that the upstream geometry plays a significant role on vortex growth
dynamics.
Abstract: Currently, there is no database or local norms for the
physical performance of Malaysian rugby players. This database or
norms are vital for Malaysian-s sports development as programs can
be setup to improve the current status. This pilot study was
conducted to evaluate the status of our semi professional rugby
players. The rugby players were randomly selected from the
Malaysian National team and several clubs in the Klang valley, Kuala
Lumpur Malaysia. 54 male rugby players (Age: 24.41 ± 4.06 years)
were selected for this pilot study. Height, bodyweight, percentage
body fat and body mass index (BMI) and several other physical tests
were performed. Results from the BLEEP test revealed an average of
level 9, shuttle 2 for the players. Interestingly, forwards were taller,
heavier, and had lower maximal aerobic power than backs in the
same team. In conclusion, the physical characteristics of the rugby
players were much lower when compared to international players
from other countries. From this pilot study, the physical performance
of the Malaysian team must be improved in order to further develop
the sports.
Abstract: Considering today-s increasing speed of change,
radical and innovative improvement - Kaikaku, is a necessity parallel
to continuous incremental improvement - Kaizen, especially for
SME-s in order to attain the competitive edge needed to be profitable.
During 2011, a qualitative single case study with the objective of
realizing a kaikaku in production has been conducted. The case study
was run as a one year project using a collaborative approach
including both researchers and company representatives. The case
study was conducted with the purpose of gaining further knowledge
about kaikaku realization as well as its implications. The empirical
results provide insights about the great productivity results achieved
by applying a specific kaikaku realization approach. However, it also
sheds light on the difficulty and contradiction of combining
innovation management and production system development.
Abstract: Repairing of the cracks by fiber metal laminates
(FMLs) was first done by some aeronautical laboratories in early
1970s. In this study, experimental investigations were done on the
effect of repairing the center-cracked aluminum plates using the FML
patches. The repairing processes were conducted to characterize the
response of the repaired structures to tensile tests. The composite
patches were made of one aluminum layer and two woven glassepoxy
composite layers. Three different crack lengths in three crack
angles and different patch lay-ups were examined. It was observed
for the lengthen cracks, the effect of increasing the crack angle on
ultimate tensile load in the structure was increase. It was indicated
that the situation of metal layer in the FML patches had an important
effect on the tensile response of the tested specimens. It was found
when the aluminum layer is farther, the ultimate tensile load has the
highest amount.
Abstract: Along with the basic features of students\' culture
information, with its widely usage oriented on implementation of the
new information technologies in educational process that determines
the search for ways of pointing to the similarity of interdisciplinary
connections content, aims and objectives of the study. In this regard,
the article questions about students\' information culture, and also
presented information about the aims and objectives of the
information culture process among students. In the formation of a
professional interest in relevant information, which is an opportunity
to assist in informing the professional activities of the essence of
effective use of interactive methods and innovative technologies in
the learning process. The result of the experiment proves the
effectiveness of the information culture process of students in
training the system of higher education based on the credit
technology. The main purpose of this paper is a comprehensive
review of students\' information culture.
Abstract: Hydrogenated biodiesel is one of the most promising
renewable fuels. It has many advantages over conventional biodiesel,
including higher cetane number, higher heating value, lower
viscosity, and lower corrosiveness due to its absence of oxygen.
From previous work, Pd/TiO2 gave high conversion and selectivity in
hydrogenated biodiesel. In this work, the effect of biomass feedstocks
(i.e. beef fat, chicken fat, pork fat, and jatropha oil) on the production
of hydrogenated biodiesel over Pd/TiO2 has been studied. Biomass
feedstocks were analyzed by ICP-OES (inductively coupled plasma
optical emission spectrometry) to identify the content of impurities
(i.e. P, K, Ca, Na, and Mg). The deoxygenation catalyst, Pd/TiO2,
was prepared by incipient wetness impregnation (IWI) and tested in a
continuous flow packed-bed reactor at 500 psig, 325°C, H2/feed
molar ratio of 30, and LHSV of 4 h-1 for its catalytic activity and
selectivity in hydrodeoxygenation. All feedstocks gave high
selectivity in diesel specification range hydrocarbons and the main
hydrocarbons were n-pentadecane (n-C15) and n-heptadecane (n-
C17), resulting from the decarbonylation/decarboxylation reaction.
Intermediates such as oleic acid, stearic acid, palmitic acid, and esters
were also detected in minor amount. The conversion of triglycerides
in jatropha oil is higher than those of chicken fat, pork fat, and beef
fat, respectively. The higher concentration of metal impurities in
feedstock, the lower conversion of feedstock.
Abstract: Buckling-Restrained Braced Frame system(BRBFs)
are a new type of steel seismic-load-resisting system that has found
use in several countries because of its efficiency and its promise of
seismic performance far superior to that of conventional braced
frames. The system is addressed in the 2005 edition of the AISC
Seismic Provisions for Structural Steel Buildings, also a set of design
provisions has been developed by NEHRP. This report illustrates the
seismic design of buckling restrained braced frames and compares
the result of design in the application of earthquake load for ordinary
bracing systems and buckling restrained bracing systems to see the
advantage and disadvantages of this new type of seismic resisting
system in comparison with the old Ordinary Concentric Braced
Frame systems (OCBFs); they are defined by the provisions
governing their design.
Abstract: Microarray experiments are information rich; however, extensive data mining is required to identify the patterns that characterize the underlying mechanisms of action. For biologists, a key aim when analyzing microarray data is to group genes based on the temporal patterns of their expression levels. In this paper, we used an iterative clustering method to find temporal patterns of gene expression. We evaluated the performance of this method by applying it to real sporulation data and simulated data. The patterns obtained using the iterative clustering were found to be superior to those obtained using existing clustering algorithms.
Abstract: The selective recovery of heavy metals of Cu, Zn, Ni and Cr from a mixed plating sludge by sulfidation and oxidation treatment was targeted in this study. At first, the mixed plating sludge was simultaneously subjected to an extraction and Cu sulfidation process at pH=1.5 to dissolve heavy metals and to precipitate Cu2+ as CuS. In the next step, the sulfidation treatment of Zn was carried out at pH=4.5 and the residual solution was subjected to an oxidation treatment of chromium with H2O2 at pH=10.0. After the experiments, the selectivity of metal precipitation and the chromium oxidation ratio were evaluated. As results, it was found that the filter cake obtained after selective sulfidation of Cu was composed of 96.6% of Cu (100% equals to the sum of Cu, Zn, Ni and Cr contents). Such findings confirmed that almost complete extraction of heavy metals was achieved at pH=1.5 and also that Cu could be selectively recovered as CuS. Further, the filter cake obtained at pH=4.5 was composed of 91.5% Zn and 6.83% of Cr. Regarding the chromium oxidation step, the chromium oxidation ratio was found to increase with temperature and the addition of oxidation agent of H2O2, but only oxidation ratio of 59% was achieved at a temperature of 60°C and H2O2 to Cr3+ equivalent ratio of 180.
Abstract: Heterogeneous catalysis is vital for a number of
chemical, refinery and pollution control processes. The use of
catalyst pellets of hollow cylindrical shape provide several distinct
advantages over other common shapes, and can therefore help to
enhance conversion levels in reactors. A better utilization of the
catalytic material is probably most notable of these features due to
the absence of the pellet core, which helps to significantly lower the
effect of the internal transport resistance. This is reflected in the
enhancement of the effectiveness factor. For the case of the first order
irreversible kinetics, a substantial increase in the effectiveness factor
can be obtained by varying shape parameters. Important shape
parameters of a finite hollow cylinder are the ratio of the inside to the
outside radii (κ) and the height to the diameter ratio (γ). A high value
of κ the generally helps to enhance the effectiveness factor. On the
other hand, lower values of the effectiveness factors are obtained
when the dimension of the height and the diameter are comparable.
Thus, the departure of parameter γ from the unity favors higher
effectiveness factor. Since a higher effectiveness factor is a measure
of a greater utilization of the catalytic material, higher conversion
levels can be achieved using the hollow cylindrical pellets possessing
optimized shape parameters.
Abstract: Properly sized capacitor banks are connected across induction motors for several reasons including power factor correction, reducing distortions, increasing capacity, etc. Total harmonic distortion (THD) and power factor (PF) are used in such cases to quantify the improvements obtained through connection of the external capacitor banks. On the other hand, one of the methods for assessing the motor internal condition is by the use of Park-s pattern analysis. In spite of taking adequate precautionary measures, the capacitor banks may sometimes malfunction. Such a minor fault in the capacitor bank is often not apparently discernible. This may however, give rise to substantial degradation of power factor correction performance and may also damage the supply profile. The case is more severe with the fact that the Park-s pattern gets distorted due to such external capacitor faults, and can give anomalous results about motor internal fault analyses. The aim of this paper is to present simulation and hardware laboratory test results to have an understanding of the anomalies in harmonic distortion and Park-s pattern analyses in induction motors due to capacitor bank defects.
Abstract: Wrist pulse analysis for identification of health status
is found in Ancient Indian as well as Chinese literature. The preprocessing
of wrist pulse is necessary to remove outlier pulses and
fluctuations prior to the analysis of pulse pressure signal. This paper
discusses the identification of irregular pulses present in the pulse
series and intricacies associated with the extraction of time domain
pulse features. An approach of Dynamic Time Warping (DTW) has
been utilized for the identification of outlier pulses in the wrist pulse
series. The ambiguity present in the identification of pulse features is
resolved with the help of first derivative of Ensemble Average of
wrist pulse series. An algorithm for detecting tidal and dicrotic notch
in individual wrist pulse segment is proposed.
Abstract: This paper present some preliminary work on the
preparation and physicochemical caracterization of nanocomposite
MFI-alumina structures based on alumina hollow fibres. The fibers
are manufactured by a wet spinning process. α-alumina particles were
dispersed in a solution of polysulfone in NMP. The resulting slurry is
pressed through the annular gap of a spinneret into a precipitation
bath. The resulting green fibres are sintered. The mechanical strength
of the alumina hollow fibres is determined by a three-point-bending
test while the pore size is characterized by bubble-point testing. The
bending strength is in the range of 110 MPa while the average pore
size is 450 nm for an internal diameter of 1 mm and external diameter
of 1.7 mm. To characterize the MFI membranes various techniques
were used for physicochemical characterization of MFI–ceramic
hollow fibres membranes: The nitrogen adsorption, X-ray
diffractometry, scanning electron microscopy combined with X
emission microanalysis. Scanning Electron Microscopy (SEM) and
Energy Dispersive Microanalysis by the X-ray were used to observe
the morphology of the hollow fibre membranes (thickness,
infiltration into the carrier, defects, homogeneity). No surface film,
has been obtained, as observed by SEM and EDX analysis and
confirmed by high temperature variation of N2 and CO2 gas
permeances before cation exchange. Local analysis and characterise
(SEM and EDX) and overall (by ICP elemental analysis) were
conducted on two samples exchanged to determine the quantity and
distribution of the cation of cesium on the cross section fibre of the
zeolite between the cavities.
Abstract: We introduce a new interactive 3D simulator of ocular motion and expressions suitable for: (1) character animation applications to game design, film production, HCI (Human Computer Interface), conversational animated agents, and virtual reality; (2) medical applications (ophthalmic neurological and muscular pathologies: research and education); and (3) real time simulation of unconscious cognitive and emotional responses (for use, e.g., in psychological research). Using state-of-the-art computer animation technology we have modeled and rigged a physiologically accurate 3D model of the eyes, eyelids, and eyebrow regions and we have 'optimized' it for use with an interactive and web deliverable platform. In addition, we have realized a prototype device for realtime control of eye motions and expressions, including unconsciously produced expressions, for application as in (1), (2), and (3) above. The 3D simulator of eye motion and ocular expression is, to our knowledge, the most advanced/realistic available so far for applications in character animation and medical pedagogy.
Abstract: Achieving success is a highly critical issue for the
companies to survive in a competitive business environment. The
construction industry is also an area where there is strong
competition due to a large number of construction contractors. There
have been many factors such as qualified employees, quality
workmanship and financial management that can lead to company
success in the construction industry. The aim of this study was to
investigate the critical factors leading to construction company
success. Within this context, a survey was carried out among 40
Turkish construction companies which are located in the Northwest
region of Turkey. In this survey, top-level managers and owners of
the companies were interviewed. The interviews took place over a
five month period between January and May 2007. Finally, the
ranking of the critical success factors has been determined by using
the Simple Multi Attribute Rating Technique (SMART). Based on
the results, business management, financial conditions and
owner/manager characteristics were determined as the most
important factors to company success.
Abstract: Renewable natural fibres such as oil palm, flax, and
pineapple leaf can be utilized to obtain new high performance
polymer materials. The reuse of waste natural fibres as reinforcement
for polymer is a sustainable option to the environment. However, due
to its high hydroxyl content of cellulose, natural fibres are
susceptible to absorb water that affects the composite mechanical
properties adversely. Research found that Nano materials such as
Nano Silica Carbide (n-SiC) and Nano Clay can be added into the
polymer composite to overcome this problem by enhancing its
mechanical properties in wet condition. The addition of Nano
material improves the tensile and wear properties, flexural stressstrain
behaviour, fracture toughness, and fracture strength of polymer
natural composites in wet and dry conditions.
Abstract: The use of wind energy for electricity generation is
growing rapidly across the world and in Portugal. However, the
geographical characteristics of the country along with the average
wind regime and with the environmental restrictions imposed to these
projects create limitations to the exploit of the onshore wind
resource. The best onshore wind spots are already committed and the
possibility of offshore wind farms in the Portuguese cost is now
being considered. This paper aims to make a contribution to the
evaluation of offshore wind power projects in Portugal. The technical
restrictions are addressed and the strategic, environmental and
financial interest of the project is analysed from the private company
and public points of view. The results suggest that additional support
schemes are required to ensure private investors interest for these
projects. Assuming an approach of direct substitution of energy
sources for electricity generation, the avoided CO2 equivalent
emissions for an offshore wind power project were quantified. Based
on the conclusions, future research is proposed to address the
environmental and social impacts of these projects.
Abstract: the current study presents a modeling framework to determine the torsion strength of an induction hardened splined shaft by considering geometry and material aspects with the aim to optimize the static torsion strength by selection of spline geometry and hardness depth. Six different spline geometries and seven different hardness profiles including non-hardened and throughhardened shafts have been considered. The results reveal that the torque that causes initial yielding of the induction hardened splined shaft is strongly dependent on the hardness depth and the geometry of the spline teeth. Guidelines for selection of the appropriate hardness depth and spline geometry are given such that an optimum static torsion strength of the component can be achieved.
Abstract: This paper presents the adaptive control scheme
with sliding mode compensator for vibration control problem
in the presence of disturbance. The dynamic model of the
flexible cantilever beam using finite element modeling is
derived. The adaptive control with sliding mode compensator
using output feedback for output tracking is developed to
reject the external disturbance, and to improve the tracking
performance. Satisfactory simulation results verify that the
effectiveness of adaptive control scheme with sliding mode
compensator.