Abstract: Hair is a non homogenous complex material which
can be associated with a polymer. It is made up 95% of Keratin.
Hair has a great social significance for human beings. In the High
Middle Ages, for example, long hairs have been reserved for kings
and nobles.
Most common interest in hair is focused on hair growth, hair types
and hair care, but hair is also an important biomaterial which can
vary depending on ethnic origin or on age, hair colour for example
can be a sign of ethnic ancestry or age (dark hair for Asiatic, blond
hair for Caucasian and white hair for old people in general).
In this context, different approaches have been conducted to
determine the differences in mechanical properties and characterize
the fracture topography at the surface of hair depending on its type
and its age.
A tensile testing machine was especially designed to achieve
tensile tests on hair. This device is composed of a microdisplacement
system and a force sensor whose peak load is limited to
3N. The curves and the values extracted from each experiment, allow
us to compare the evolution of the mechanical properties from one
hair to another.
Observations with a Scanning Electron Microscope (SEM) and
with an interferometer were made on different hairs. Thus, it is
possible to access the cuticle state and the fracture topography for
each category.
Abstract: In our recent study, we have used ZnO nanoparticles assisted with UV light irradiation to investigate the photocatalytic degradation of Phenol Red (PR). The ZnO photocatalyst was characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), specific surface area analysis (BET) and UVvisible spectroscopy. X-ray diffractometry result for the ZnO nanoparticles exhibit normal crystalline phase features. All observed peaks can be indexed to the pure hexagonal wurtzite crystal structures, with the space group of P63mc. There are no other impurities in the diffraction peak. In addition, TEM measurement shows that most of the nanoparticles are rod-like and spherical in shape and fairly monodispersed. A significant degradation of the PR was observed when the catalyst was added into the solution even without the UV light exposure. In addition, the photodegradation increases with the photocatalyst loading. The surface area of the ZnO nanomaterials from the BET measurement was 11.9 m2/g. Besides the photocatalyst loading, the effect of some parameters on the photodegradation efficiency such as initial PR concentration and pH were also studied.
Abstract: The onset of Marangoni convection in a horizontal
fluid layer with internal heat generation overlying a solid layer
heated from below is studied. The upper free surface of a fluid is
nondeformable and the bottom boundary are rigid and no-slip. The
resulting eigenvalue problem is solved exactly. The critical values of
the Marangoni numbers for the onset of Marangoni convection are
calculated and the latter is found to be critically dependent on the
internal heating, depth ratio and conductivity ratio. The effects of the
thermal conductivity and the thickness of the solid plate on the onset
of convective instability with internal heating are studied in detail.
Abstract: Wet chemistry methods are used to prepare the
SiO2/Au nanoshells. The purpose of this research was to synthesize
gold coated SiO2 nanoshells for biomedical applications. Tunable
nanoshells were prepared by using different colloidal concentrations.
The nanoshells are characterized by FTIR, XRD, UV-Vis
spectroscopy and atomic force microscopy (AFM). The FTIR results
confirmed the functionalization of the surfaces of silica nanoparticles
with NH2 terminal groups. A tunable absorption was observed
between 470-600 nm with a maximum range of 530-560 nm. Based
on the XRD results three main peaks of Au (111), (200) and (220)
were identified. Also AFM results showed that the silica core
diameter was about 100 nm and the thickness of gold shell about 10
nm.
Abstract: Protective coatings that resist oxide scale growth and
decrease chromium evaporation are necessary to make stainless steel
interconnect materials for long-term durable operation of solid oxide
fuel cells (SOFCs). In this study a layer of cobalt was electroplated
on the surface of AISI 441 ferritic stainless steel which is used in
solid oxide fuel cells for interconnect applications. The oxidation
behavior of coated substrates was studied as a function of time at
operating conditions of SOFCs. Cyclic oxidation has been also tested
at 800ºC for 100 cycles. Cobalt coating during isothermal oxidation
caused to the oxide growth resistance by limiting the outward
diffusion of Cr cation and the inward diffusion of oxygen anion.
Results of cyclic oxidation exhibited that coated substrates
demonstrate an excellent resistance against the spallation and
cracking.
Abstract: A two dimensional numerical simulation has been
performed for incompressible and compressible fluid flow through
microchannels in slip flow regime. The Navier-Stokes equations have
been solved in conjunction with Maxwell slip conditions for
modeling flow field associated with slip flow regime. The wall
roughness is simulated with triangular microelements distributed on
wall surfaces to study the effects of roughness on fluid flow. Various
Mach and Knudsen numbers are used to investigate the effects of
rarefaction as well as compressibility. It is found that rarefaction has
more significant effect on flow field in microchannels with higher
relative roughness. It is also found that compressibility has more
significant effects on Poiseuille number when relative roughness
increases. In addition, similar to incompressible models the increase
in average fRe is more significant at low Knudsen number flows but
the increase of Poiseuille number duo to relative roughness is sharper
for compressible models. The numerical results have also validated
with some available theoretical and experimental relations and good
agreements have been seen.
Abstract: Absorptive characteristics of polyaniline synthesized
in mixture of water and acetonitrile in 50/50 volume ratio was
studied. Synthesized polyaniline in powder shape is used as an
adsorbent to remove toxic hexavalent chromium from aqueous
solutions. Experiments were conducted in batch mode with different
variables such as agitation time, solution pH and initial concentration
of hexavalent chromium. Removal mechanism is the combination of
surface adsorption and reduction. The equilibrium time for removal
of Cr(T) and Cr(VI) was about 2 and 10 minutes respectively. The
optimum pH for total chromium removal occurred at pH 7 and
maximum hexavalent chromium removal took place under acidic
condition at pH 3. Investigating the isothermal characteristics showed
that the equilibrium adsorption data fitted both Freundlich-s and
Langmuir-s isotherms. The maximum adsorption of chromium was
calculated 36.1 mg/g for polyaniline
Abstract: The composite materials were prepared by sawdust, cassava starch and natural rubber latex (NR). The mixtures of 15%w/v gelatinized cassava starch and 15%w/v PVOH were used as the binder of these composite materials. The concentrated rubber latex was added to the mixtures. They were mixed rigorously to the treated sawdust in the ratio of 70:30 until achive uniform dispersion. The batters were subjected to the hot compression moulding at the temperature of 160°C and 3,000 psi pressure for 5 min. The experimental results showed that the mechanical properties of composite materials, which contained the gelatinized cassava starch and PVOH in the ratio of 2:1, 20% NR latex by weight of the dry starch and treated sawdust with 5%NaOH or 1% BPO, were the best. It contributed the maximal compression strength (341.10 + 26.11 N), puncture resistance (8.79 + 0.98 N/mm2) and flexural strength (3.99 + 0.72N/mm2). It is also found that the physicochemical and mechanical properties of composites strongly depends on the interface quality of sawdust, cassava starch and NR latex.
Abstract: Optimization of cutting parameters important in precision machining in regards to efficiency and surface integrity of the machined part. Usually productivity and precision in machining is limited by the forces emanating from the cutting process. Due to the inherent varying nature of the workpiece in terms of geometry and material composition, the peak cutting forces vary from point to point during machining process. In order to increase productivity without compromising on machining accuracy, it is important to control these cutting forces. In this paper a fuzzy logic control algorithm is developed that can be applied in the control of peak cutting forces in milling of spherical surfaces using ball end mills. The controller can adaptively vary the feedrate to maintain allowable cutting force on the tool. This control algorithm is implemented in a computer numerical control (CNC) machine. It has been demonstrated that the controller can provide stable machining and improve the performance of the CNC milling process by varying feedrate.
Abstract: Adopting the measured constitutive relationship of
stress-strain of river ice, the finite element analysis model of
percussive force of river ice and pier is established, by the explicit
dynamical analysis software package LS-DYNA. Effects of element
types, contact method and arithmetic of ice and pier, coupled modes
between different elements, mesh density of pier, and ice sheet in
contact area on the collision force are studied. Some of measures for
the collision force analysis of river ice and pier are proposed as
follows: bridge girder can adopt beam161 element with 3-node; pier
below the line of 1.30m above ice surface and ice sheet use solid164
element with 8-node; in order to accomplish the connection of
different elements, the rigid body with 0.01-0.05m thickness is defined
between solid164 and beam161; the contact type of ice and pier adopts
AUTOMATIC_SURFACE_TO_SURFACE, using symmetrical
penalty function algorithms; meshing size of pier below the line of
1.30m above ice surface should not less than 0.25×0.25×0.5m3. The
simulation results have the advantage of high precision by making a
comparison between measured and computed data. The research
results can be referred for collision force study between river ice and
pier.
Abstract: A judicious choice of insert material, tool geometry and
cutting conditions can make hard turning produce better surfaces than
grinding. In the present study, an attempt has been made to
investigate the effect of cutting tool materials on cutting forces (feed
force, thrust force and cutting force) in finish hard turning of AISI
D2 cold work tool steel. In conclusion of the results obtained with a
constant depth of cut and feed rate, it is important to note that cutting
force is directly affected by cutting tool material.
Abstract: Cashew nut shells were converted into activated carbon powders using KOH activation plus CO2 gasification at 1027 K. The increase both of impregnation ratio and activation time, there was swiftly the development of mesoporous structure with increasing of mesopore volume ratio from 20-28% and 27-45% for activated carbon with ratio of KOH per char equal to 1 and 4, respectively. Activated carbon derived from KOH/char ratio equal to 1 and CO2 gasification time from 20 to 150 minutes were exhibited the BET surface area increasing from 222 to 627 m2.g-1. And those were derived from KOH/char ratio of 4 with activation time from 20 to 150 minutes exhibited high BET surface area from 682 to 1026 m2.g-1. The adsorption of Lead(II) and Cadmium(II) ion was investigated. This adsorbent exhibited excellent adsorption for Lead(II) and Cadmium(II) ion. Maximum adsorption presented at 99.61% at pH 6.5 and 98.87% at optimum conditions. The experimental data was calculated from Freundlich isotherm and Langmuir isotherm model. The maximum capacity of Pb2+ and Cd2+ ions was found to be 28.90 m2.g-1 and 14.29 m2.g-1, respectively.
Abstract: Concerning the measurement of friction properties of
textiles and fabrics using Kawabata Evaluation System (KES), whose
output is constrained to the surface friction factor of fabric, and no
other data would be generated; this research has been conducted to
gain information about surface roughness regarding its surface
friction factor. To assess roughness properties of light nonwovens, a
3-dimensional model of a surface has been simulated with regular
sinuous waves through it as an ideal surface. A new factor was
defined, namely Surface Roughness Factor, through comparing
roughness properties of simulated surface and real specimens. The
relation between the proposed factor and friction factor of specimens
has been analyzed by regression, and results showed a meaningful
correlation between them. It can be inferred that the new presented
factor can be used as an acceptable criterion for evaluating the
roughness properties of light nonwoven fabrics.
Abstract: The steady-state temperature for one-dimensional transpiration cooling system has been conducted experimentally and numerically to investigate the heat transfer characteristics of combined convection and radiation. The Nickel –Chrome (Ni-Cr) open-cellular porous material having porosity of 0.93 and pores per inch (PPI) of 21.5 was examined. The upper surface of porous plate was heated by the heat flux of incoming radiation varying from 7.7 - 16.6 kW/m2 whereas air injection velocity fed into the lower surface was varied from 0.36 - 1.27 m/s, and was then rearranged as Reynolds number (Re). For the report of the results in the present study, two efficiencies including of temperature and conversion efficiency were presented. Temperature efficiency indicating how close the mean temperature of a porous heat plate to that of inlet air, and increased rapidly with the air injection velocity (Re). It was then saturated and had a constant value at Re higher than 10. The conversion efficiency, which was regarded as the ability of porous material in transferring energy by convection after absorbed from heat radiation, decreased with increasing of the heat flux and air injection velocity. In addition, it was then asymptotic to a constant value at the Re higher than 10. The numerical predictions also agreed with experimental data very well.
Abstract: This paper presents an exact solution and a finite element method (FEM) for a Piezoceramic Rod under static load. The cylindrical rod is made from polarized ceramics (piezoceramics) with axial poling. The lateral surface of the rod is traction-free and is unelectroded. The two end faces are under a uniform normal traction. Electrically, the two end faces are electroded with a circuit between the electrodes, which can be switched on or off. Two cases of open and shorted electrodes (short circuit and open circuit) will be considered. Finally, a finite element model will be used to compare the results with an exact solution. The study uses ABAQUS (v.6.7) software to derive the finite element model of the ceramic rod.
Abstract: The bonding configuration and the heat of adsorption
of a furfural molecule on the Pd(111) surface were determined by ab
initio density-functional-theory calculations. The dynamics of pure
liquid water, the liquid-solid interface formed by liquid water and the
Pd(111) surface, as well as furfural at the water-Pd interface, were
investigated by ab initio molecular dynamics simulations at finite
temperatures. Calculations and simulations suggest that the bonding
configurations at the water-Pd interface promote decarbonylation of
furfural.
Abstract: This paper presents a study of the Taguchi design
application to optimize surface quality in damper inserted end milling
operation. Maintaining good surface quality usually involves
additional manufacturing cost or loss of productivity. The Taguchi
design is an efficient and effective experimental method in which a
response variable can be optimized, given various factors, using
fewer resources than a factorial design. This Study included spindle
speed, feed rate, and depth of cut as control factors, usage of different
tools in the same specification, which introduced tool condition and
dimensional variability. An orthogonal array of L9(3^4)was used;
ANOVA analyses were carried out to identify the significant factors
affecting surface roughness, and the optimal cutting combination was
determined by seeking the best surface roughness (response) and
signal-to-noise ratio. Finally, confirmation tests verified that the
Taguchi design was successful in optimizing milling parameters for
surface roughness.
Abstract: A minimal complexity version of component mode
synthesis is presented that requires simplified computer
programming, but still provides adequate accuracy for modeling
lower eigenproperties of large structures and their transient
responses. The novelty is that a structural separation into components
is done along a plane/surface that exhibits rigid-like behavior, thus
only normal modes of each component is sufficient to use, without
computing any constraint, attachment, or residual-attachment modes.
The approach requires only such input information as a few (lower)
natural frequencies and corresponding undamped normal modes of
each component. A novel technique is shown for formulation of
equations of motion, where a double transformation to generalized
coordinates is employed and formulation of nonproportional damping
matrix in generalized coordinates is shown.
Abstract: In this study, the effects of machining parameters on
specific energy during surface grinding of 6061Al-SiC35P
composites are investigated. Vol% of SiC, feed and depth of cut were
chosen as process variables. The power needed for the calculation of
the specific energy is measured from the two watt meter method.
Experiments are conducted using standard RSM design called Central
composite design (CCD). A second order response surface model was
developed for specific energy. The results identify the significant
influence factors to minimize the specific energy. The confirmation
results demonstrate the practicability and effectiveness of the
proposed approach.
Abstract: Nanoemulsions are a class of emulsions with a droplet
size in the range of 50–500 nm and have attracted a great deal of
attention in recent years because it is unique characteristics. The
physicochemical properties of nanoemulsion suggests that it can be
successfully used to recover the residual oil which is trapped in the
fine pore of reservoir rock by capillary forces after primary and
secondary recovery. Oil-in-water nanoemulsion which can be formed
by high-energy emulsification techniques using specific surfactants
can reduce oil-water interfacial tension (IFT) by 3-4 orders of
magnitude. The present work is aimed on characterization of oil-inwater
nanoemulsion in terms of its phase behavior, morphological
studies; interfacial energy; ability to reduce the interfacial tension and
understanding the mechanisms of mobilization and displacement of
entrapped oil blobs by lowering interfacial tension both at the
macroscopic and microscopic level. In order to investigate the
efficiency of oil-water nanoemulsion in enhanced oil recovery
(EOR), experiments were performed to characterize the emulsion in
terms of their physicochemical properties and size distribution of the
dispersed oil droplet in water phase. Synthetic mineral oil and a series
of surfactants were used to prepare oil-in-water emulsions.
Characterization of emulsion shows that it follows pseudo-plastic
behaviour and drop size of dispersed oil phase follows lognormal
distribution. Flooding experiments were also carried out in a
sandpack system to evaluate the effectiveness of the nanoemulsion as
displacing fluid for enhanced oil recovery. Substantial additional
recoveries (more than 25% of original oil in place) over conventional
water flooding were obtained in the present investigation.