Abstract: We investigate the ZnO role in the inherent protection
of old manuscripts to protect them against environmental damaging
effect of ultraviolet radiation, pollutant gasses, mold and bacteria. In
this study a cellulosic nanocomposite of ZnO were used as protective
coating on the surface of paper fibers. This layered nanocomposite
can act as a consolidate materials too. Furthermore, to determine how
well paper works screen objects from the damaging effects, two
accelerated aging mechanisms due to light and heat are discussed.
Results show good stability of papers with nanocomposite coating.
Also, a good light stability was shown in the colored paper that
treated with this nanocomposite. Furthermore, to demonstrate the
degree of antifungal and antibacterial properties of coated papers,
papers was treated with four common molds and bacteria and the
good preventive effects of coated paper against molds and bacteria
are described.
Abstract: This paper investigates the influence of various
parameters on the behaviour of water droplets on polymeric surfaces
under high electric fields. An inclined plane test was carried out to
understand the droplet behaviour in strong electric field. Parameters
such as water droplet conductivity, droplet volume, polymeric
surface roughness and droplet positioning with respect to the
electrodes were studied. The flashover voltage is affected by all
aforementioned parameters. The droplet positioning is in some cases
more vital than the droplet volume. Surface damages were analysed
using Scanning Electron Microscopy (SEM) studies and by Energy
dispersive X-ray Analysis (EDAX). It is observes that magnitude of
discharge have direct influence on amount of surface da
Abstract: The results of an experimental study of the process of
convective and boiling heat transfer in the vessel with stirrer for
smooth and rough ring-shaped pipes are presented. It is established
that creation of two-dimensional artificial roughness on the heated
surface causes the essential (~100%) intensification of convective
heat transfer. In case of boiling the influence of roughness appears on
the initial stage of boiling and in case of fully developed nucleate
boiling there was no intensification of heat transfer. The similitude
equation for calculating convective heat transfer coefficient, which
generalizes well experimental data both for the smooth and the rough
surfaces is proposed.
Abstract: An HPLC-UV analytical method was developed to
determine ethylenediaminetetraacetic acid (EDTA) in dairy
wastewater and surface water. The optimizing separation was achieved
by reversed–phase ion-pair liquid chromatography on a C18 column
using methanol as mobile phase solvent, tetrabutylammonium bromide
as the ion-pair reagent in pH 3.3 formate buffer solution at a flow rate
of 0.9 mL min-1 with a UV detector at 265 nm. No interference of Ca,
Mg or NO3
- was detected. Method performance was evaluated in terms
of linearity, repeatability and reproducibility. The method detection
limit was 5 μg L-1. The contents of EDTA in dairy effluents were 72 ~
261 μg L-1 at a large dairy site. A change of EDTA concentration was
observed downstream of the dairy effluent discharge, but this was well
under the predicted no effect concentration for aquatic ecosystem.
Abstract: Pressure vessels are usually operating at temperatures
where the conditions of linear elastic fracture mechanics are no
longer met because massive plasticity precedes crack propagation. In
this work the development of a surface crack in a pressure vessel
subject to bending and tension under elastic-plastic fracture
mechanics conditions was investigated. Finite element analysis was
used to evaluate the hydrostatic stress, the J-integral and crack
growth for semi-elliptical surface-breaking cracks. The results
showed non-uniform stress triaxiality and crack driving force around
the crack front at large deformation levels. Different ductile crack
extensions were observed which emphasis the dependent of ductile
tearing on crack geometry and type of loading. In bending the crack
grew only beneath the surface, and growth was suppressed at the
deepest segment. This contrasts to tension where the crack breaks
through the thickness with uniform growth along the entire crack
front except at the free surface. Current investigations showed that
the crack growth developed under linear elastic fracture mechanics
conditions will no longer be applicable under ductile tearing
scenarios.
Abstract: In the present work, an attempt has been made to
understand the feasibility of using UHF technique for identification
of any corona discharges/ arcing in insulating material due to water
droplets. The sensors of broadband type are useful for identification
of such discharges. It is realised that arcing initiated by liquid droplet
radiates UHF signals in the entire bandwidth up to 2 GHz. The
frequency content of the UHF signal generated due to corona/arcing
is not much varied in epoxy nanocomposites with different weight
percentage of clay content. The exfoliated/intercalated properties
were analysed through TEM studies. It is realized that corona
initiated discharges are of intermittent process. The hydrophobicity
of the material characterized through contact angle measurement. It
is realized that low Wt % of nanoclay content in epoxy resin reduces
the surface carbonization due to arcing/corona discharges. The results
of the study with gamma irradiated specimen indicates that contact
angle, discharge inception time and evaporation time of the liquid are
much lower than the virgin epoxy nanocomposite material.
Abstract: Large full frequency band gaps of surface and bulk
acoustic waves in two-dimensional phononic band structures with
hollow cylinders are addressed in this paper. It is well-known that
absolute frequency band gaps are difficultly obtained in a band
structure consisted of low-acoustic-impedance cylinders in
high-acoustic-impedance host materials such as PMMA/Ni band
structures. Phononic band structures with hollow cylinders are
analyzed and discussed to obtain large full frequency band gaps not
only for bulk modes but also for surface modes. The tendency of
absolute frequency band gaps of surface and bulk acoustic waves is
also addressed by changing the inner radius of hollow cylinders in this
paper. The technique and this kind of band structure are useful for
tuning the frequency band gaps and the design of acoustic waveguides.
Abstract: This paper presents the simulation the results of
electric field and potential distributions along surface of silicone
rubber polymer insulators. Near the same leakage distance subjected
to 15 kV in 50 cycle salt fog ageing test, alternate sheds silicone
rubber polymer insulator showed better contamination performance
than straight sheds silicone rubber polymer insulator. Severe surface
ageing was observed on the straight sheds insulator. The objective of
this work is to elucidate that electric field distribution along straight
sheds insulator higher than alternate shed insulator in salt fog ageing
test. Finite element method (FEM) is adopted for this work. The
simulation results confirmed the experimental data, as well.
Abstract: Repeated observation of a given area over time yields
potential for many forms of change detection analysis. These
repeated observations are confounded in terms of radiometric
consistency due to changes in sensor calibration over time,
differences in illumination, observation angles and variation in
atmospheric effects.
This paper demonstrates applicability of an empirical relative
radiometric normalization method to a set of multitemporal cloudy
images acquired by Resourcesat1 LISS III sensor. Objective of this
study is to detect and remove cloud cover and normalize an image
radiometrically. Cloud detection is achieved by using Average
Brightness Threshold (ABT) algorithm. The detected cloud is
removed and replaced with data from another images of the same
area. After cloud removal, the proposed normalization method is
applied to reduce the radiometric influence caused by non surface
factors. This process identifies landscape elements whose reflectance
values are nearly constant over time, i.e. the subset of non-changing
pixels are identified using frequency based correlation technique. The
quality of radiometric normalization is statistically assessed by R2
value and mean square error (MSE) between each pair of analogous
band.
Abstract: This paper presents an automatic feature recognition
method based on center-surround difference detecting and fuzzy logic
that can be applied in ground-penetrating radar (GPR) image
processing. Adopted center-surround difference method, the salient
local image regions are extracted from the GPR images as features of
detected objects. And fuzzy logic strategy is used to match the
detected features and features in template database. This way, the
problem of objects detecting, which is the key problem in GPR image
processing, can be converted into two steps, feature extracting and
matching. The contributions of these skills make the system have the
ability to deal with changes in scale, antenna and noises. The results of
experiments also prove that the system has higher ratio of features
sensing in using GPR to image the subsurface structures.
Abstract: The electrolyte stirring method of anodization etching
process for manufacturing porous silicon (PS) is reported in this work.
Two experimental setups of nature air stirring (PS-ASM) and
electrolyte stirring (PS-ESM) are employed to clarify the influence of
stirring mechanisms on electrochemical etching process. Compared to
traditional fabrication without any stirring apparatus (PS-TM), a large
plateau region of PS surface structure is obtained from samples with
both stirring methods by the 3D-profiler measurement. Moreover, the
light emission response is also improved by both proposed electrolyte
stirring methods due to the cycling force in electrolyte could
effectively enhance etch-carrier distribution while the electrochemical
etching process is made. According to the analysis of statistical
calculation of photoluminescence (PL) intensity, lower standard
deviations are obtained from PS-samples with studied stirring methods,
i.e. the uniformity of PL-intensity is effectively improved. The
calculated deviations of PL-intensity are 93.2, 74.5 and 64,
respectively, for PS-TM, PS-ASM and PS-ESM.
Abstract: The potential of economically cheaper cellulose
containing natural materials like rice husk was assessed for nickel
adsorption from aqueous solutions. The effects of pH, contact time,
sorbent dose, initial metal ion concentration and temperature on the
uptake of nickel were studied in batch process. The removal of nickel
was dependent on the physico-chemical characteristics of the
adsorbent, adsorbate concentration and other studied process
parameters. The sorption data has been correlated with Langmuir,
Freundlich and Dubinin-Radush kevich (D-R) adsorption models. It
was found that Freundlich and Langmuir isotherms fitted well to the
data. Maximum nickel removal was observed at pH 6.0. The
efficiency of rice husk for nickel removal was 51.8% for dilute
solutions at 20 g L-1 adsorbent dose. FTIR, SEM and EDAX were
recorded before and after adsorption to explore the number and
position of the functional groups available for nickel binding on to
the studied adsorbent and changes in surface morphology and
elemental constitution of the adsorbent. Pseudo-second order model
explains the nickel kinetics more effectively. Reusability of the
adsorbent was examined by desorption in which HCl eluted 78.93%
nickel. The results revealed that nickel is considerably adsorbed on
rice husk and it could be and economic method for the removal of
nickel from aqueous solutions.
Abstract: The B'enard-Marangoni thermal instability problem for
a viscoelastic Jeffreys- fluid layer with internal heat generation is
investigated. The fluid layer is bounded above by a realistic free
deformable surface and by a plane surface below. Our analysis
shows that while the internal heat generation and the relaxation time
both destabilize the fluid layer, its stability may be enhanced by an
increased retardation time.
Abstract: Various intelligences and inspirations have been
adopted into the iterative searching process called as meta-heuristics.
They intelligently perform the exploration and exploitation in the
solution domain space aiming to efficiently seek near optimal
solutions. In this work, the bee algorithm, inspired by the natural
foraging behaviour of honey bees, was adapted to find the near
optimal solutions of the transportation management system, dynamic
multi-zone dispatching. This problem prepares for an uncertainty and
changing customers- demand. In striving to remain competitive,
transportation system should therefore be flexible in order to cope
with the changes of customers- demand in terms of in-bound and outbound
goods and technological innovations. To remain higher service
level but lower cost management via the minimal imbalance scenario,
the rearrangement penalty of the area, in each zone, including time
periods are also included. However, the performance of the algorithm
depends on the appropriate parameters- setting and need to be
determined and analysed before its implementation. BEE parameters
are determined through the linear constrained response surface
optimisation or LCRSOM and weighted centroid modified simplex
methods or WCMSM. Experimental results were analysed in terms
of best solutions found so far, mean and standard deviation on the
imbalance values including the convergence of the solutions
obtained. It was found that the results obtained from the LCRSOM
were better than those using the WCMSM. However, the average
execution time of experimental run using the LCRSOM was longer
than those using the WCMSM. Finally a recommendation of proper
level settings of BEE parameters for some selected problem sizes is
given as a guideline for future applications.
Abstract: Regarding previous research studies it was concluded
that thin-walled fiber-cement composites are able to conduct electric
current under specific conditions. This property is ensured by using
of various kinds of carbon materials. Though carbon fibers are less
conductive than metal fibers, composites with carbon fibers were
evaluated as better current conductors than the composites with metal
fibers. The level of electric conductivity is monitored by the means of
impedance measurement of designed samples. These composites
could be used for a range of applications such as heating of
trafficable surfaces or shielding of electro-magnetic fields.
The aim of the present research was to design an element with the
ability to monitor internal processes in building structures and
prevent them from collapsing. As a typical element for laboratory
testing there was chosen a concrete column, which was repeatedly
subjected to load by simple pressure with continual monitoring of
changes in electrical properties.
Abstract: Greenhouse gases (GHG) emissions impose major
threat to global warming potential (GWP). Unfortunately
manufacturing sector is one of the major sources that contribute
towards the rapid increase in greenhouse gases (GHG) emissions. In
manufacturing sector electric power consumption is the major driver
that influences CO2 emission. Titanium alloys are widely utilized in
aerospace, automotive and petrochemical sectors because of their
high strength to weight ratio and corrosion resistance. Titanium
alloys are termed as difficult to cut materials because of their poor
machinability rating. The present study analyzes energy consumption
during cutting with reference to material removal rate (MRR).
Surface roughness was also measured in order to optimize energy
consumption.
Abstract: This paper aims to fabricated high quality anodic
aluminum oxide (AAO) film by anodization method. AAO pore size,
pore density, and film thickness can be controlled in 10~500 nm,
108~1011 pore．cm-2, and 1~100 μm. AAO volume and surface area can
be computed based on structural parameters such as thickness, pore
size, pore density, and sample size. Base on the thetorical calculation,
AAO has 100 μm thickness with 15 nm, 60 nm, and 500 nm pore
diameters AAO surface areas are 1225.2 cm2, 3204.4 cm2, and 549.7
cm2, respectively. The large unit surface area which is useful for
adsorption application. When AAO adsorbed pH indictor of
bromphenol blue presented a sensitive pH detection of solution
change. This testing method can further be used for the precise
measurement of biotechnology, convenience measurement of
industrial engineering.
Abstract: Air infiltration in mass scale industrial applications of
bio char production is inevitable. The presence of oxygen during the
carbonization process is detrimental to the production of biochar yield
and properties. The experiment was carried out on several wood
species in a fixed-bed pyrolyser under various fractions of oxygen
ranging from 0% to 11% by varying nitrogen and oxygen composition
in the pyrolysing gas mixtures at desired compositions. The bed
temperature and holding time were also varied. Process optimization
was carried out by Response Surface Methodology (RSM) by
employing Central Composite Design (CCD) using Design Expert 6.0
Software. The effect of oxygen ratio and holding time on biochar yield
within the range studied were statistically significant. From the
analysis result, optimum condition of 15.2% biochar yield of
mangrove wood was predicted at pyrolysis temperature of 403 oC,
oxygen percentage of 2.3% and holding time of two hours. This
prediction agreed well with the experiment finding of 15.1% biochar
yield.
Abstract: Accumulation of dust from the outdoor environment
on the panels of solar photovoltaic (PV) system is natural. There
were studies that showed that the accumulated dust can reduce the
performance of solar panels, but the results were not clearly
quantified. The objective of this research was to study the effects of
dust accumulation on the performance of solar PV panels.
Experiments were conducted using dust particles on solar panels with
a constant-power light source, to determine the resulting electrical
power generated and efficiency. It was found from the study that the
accumulated dust on the surface of photovoltaic solar panel can
reduce the system-s efficiency by up to 50%.
Abstract: This study reports the preparation of soft magnetic
ribbons of Fe-based amorphous alloys using the single-roller melt-spinning technique. Ribbon width varied from 142 mm to 213
mm and, with a thickness of approximately 22 μm ± 2 μm. The microstructure and magnetic properties of the ribbons were
characterized by differential scanning calorimeter (DSC), X-ray diffraction (XRD), vibrating sample magnetometer (VSM), and electrical resistivity measurements (ERM). The amorphous material
properties dependence of the cooling rate and nozzle pressure have uneven surface in ribbon thicknesses are investigated. Magnetic
measurement results indicate that some region of the ribbon exhibits good magnetic properties, higher saturation induction and lower coercivity. However, due to the uneven surface of 213 mm wide
ribbon, the magnetic responses are not uniformly distributed. To
understand the transformer magnetic performances, this study analyzes the measurements of a three-phase 2 MVA amorphous-cored transformer. Experimental results confirm that the transformer with a
ribbon width of 142 mm has better magnetic properties in terms of lower core loss, exciting power, and audible noise.