Abstract: The Navier–Stokes equations for unsteady, incompressible, viscous fluids in the axisymmetric coordinate system are solved using a control volume method. The volume-of-fluid (VOF) technique is used to track the free-surface of the liquid. Model predictions are in good agreement with experimental measurements. It is found that the dynamic processes after impact are sensitive to the initial droplet velocity and the liquid pool depth. The time evolution of the crown height and diameter are obtained by numerical simulation. The critical We number for splashing (Wecr) is studied for Oh (Ohnesorge) numbers in the range of 0.01~0.1; the results compares well with those of the experiments.
Abstract: The objective of the present paper is a numerical
analysis of the flow forces acting on spool surfaces of a pressure
regulated valve. The transient, compressible and turbulent flow
structures inside the valve are simulated using ANSYS FLUENT
coupled with a special UDF. Here, valve inlet pressure is varied in a
stepwise manner. For every value of inlet pressure, transient analysis
leads to a quasi-static flow through the valve. Spool forces are
calculated based on different pressures at inlet. From this information
of spool forces, pressure characteristic of the passive control circuit
has been derived.
Abstract: The incorporation of computational fluid dynamics in the design of modern hydraulic turbines appears to be necessary in order to improve their efficiency and cost-effectiveness beyond the traditional design practices. A numerical optimization methodology is developed and applied in the present work to a Turgo water turbine. The fluid is simulated by a Lagrangian mesh-free approach that can provide detailed information on the energy transfer and enhance the understanding of the complex, unsteady flow field, at very small computing cost. The runner blades are initially shaped according to hydrodynamics theory, and parameterized using Bezier polynomials and interpolation techniques. The use of a limited number of free design variables allows for various modifications of the standard blade shape, while stochastic optimization using evolutionary algorithms is implemented to find the best blade that maximizes the attainable hydraulic efficiency of the runner. The obtained optimal runner design achieves considerably higher efficiency than the standard one, and its numerically predicted performance is comparable to a real Turgo turbine, verifying the reliability and the prospects of the new methodology.
Abstract: In this paper, we propose the robust water level detection method based on the accumulated histogram under small changed image which is acquired from water level surveillance camera. In general surveillance system, this is detecting and recognizing invasion from searching area which is in big change on the sequential images. However, in case of a water level detection system, these general surveillance techniques are not suitable due to small change on the water surface. Therefore the algorithm introduces the accumulated histogram which is emphasizing change of water surface in sequential images. Accumulated histogram is based on the current image frame. The histogram is cumulating differences between previous images and current image. But, these differences are also appeared in the land region. The band pass filter is able to remove noises in the accumulated histogram Finally, this algorithm clearly separates water and land regions. After these works, the algorithm converts from the water level value on the image space to the real water level on the real space using calibration table. The detected water level is sent to the host computer with current image. To evaluate the proposed algorithm, we use test images from various situations.
Abstract: ZnO nanocrystals with mean diameter size 14 nm
have been prepared by precipitation method, and examined as
photocatalyst for the UV-induced degradation of insecticide diazinon
as deputy of organic pollutant in aqueous solution. The effects of
various parameters, such as illumination time, the amount of
photocatalyst, initial pH values and initial concentration of
insecticide on the photocatalytic degradation diazinon were
investigated to find desired conditions. In this case, the desired
parameters were also tested for the treatment of real water containing
the insecticide. Photodegradation efficiency of diazinon was
compared between commercial and prepared ZnO nanocrystals. The
results indicated that UV/ZnO process applying prepared
nanocrystalline ZnO offered electrical energy efficiency and
quantum yield better than commercial ZnO. The present study, on the
base of Langmuir-Hinshelwood mechanism, illustrated a pseudo
first-order kinetic model with rate constant of surface reaction equal
to 0.209 mg l-1 min-1 and adsorption equilibrium constant of 0.124 l
mg-1.
Abstract: Among the numerous economic evaluation techniques currently available, Multi-criteria Spatial Analysis lends itself to solving localization problems of property complexes and, in particular, production plants. The methodology involves the use of Geographical Information Systems (GIS) and the mapping overlay technique, which overlaps the different information layers of a territory in order to obtain an overview of the parameters that characterize it. This first phase is used to detect possible settlement surfaces of a new agglomeration, subsequently selected through Analytic Hierarchy Process (AHP), so as to choose the best alternative. The result ensures the synthesis of a multidimensional profile that expresses both the quantitative and qualitative effects. Each criterion can be given a different weight.
Abstract: We demonstrate a nonfaradaic electrochemical impedance spectroscopy measurement of biochemically modified gold plated electrodes using a two-electrode system. The absence of any redox indicator in the impedance measurements provide more precise and accurate characterization of the measured bioanalyte at molecular resolution. An equivalent electrical circuit of the electrodeelectrolyte interface was deduced from the observed impedance data of saline solution at low and high concentrations. The detection of biomolecular interactions was fundamentally correlated to electrical double-layer variation at modified interface. The investigations were done using 20mer deoxyribonucleic acid (DNA) strands without any label. Surface modification was performed by creating mixed monolayer of the thiol-modified single-stranded DNA and a spacer thiol (mercaptohexanol) by a two-step self-assembly method. The results clearly distinguish between the noncomplementary and complementary hybridization of DNA, at low frequency region below several hundreds Hertz.
Abstract: In this research, Response Surface Methodology (RSM) is used to investigate the effect of four controllable input variables namely: discharge current, pulse duration, pulse off time and applied voltage Surface Roughness (SR) of on Electrical Discharge Machined surface. To study the proposed second-order polynomial model for SR, a Central Composite Design (CCD) is used to estimation the model coefficients of the four input factors, which are alleged to influence the SR in Electrical Discharge Machining (EDM) process. Experiments were conducted on AISI D2 tool steel with copper electrode. The response is modeled using RSM on experimental data. The significant coefficients are obtained by performing Analysis of Variance (ANOVA) at 5% level of significance. It is found that discharge current, pulse duration, and pulse off time and few of their interactions have significant effect on the SR. The model sufficiency is very satisfactory as the Coefficient of Determination (R2) is found to be 91.7% and adjusted R2-statistic (R2 adj ) 89.6%.
Abstract: In this paper, the effect of modified clay on the
mechanical efficiency of epoxy resin is examined. Studies by X ray
diffraction and microscopic transient electron method show that
modified clay distribution in polymer area is intercalated kind.
Examination the results of mechanical tests shows that existence of
modified clay in epoxy area increases pressure yield strength, tension
module and nano composite fracture toughness in relate of pure
epoxy. By microscopic examinations it is recognized too that the
action of toughness growth of this kind of nano composite is due to
crack deflection, formation of new surfaces and fracture of clay piles.
Abstract: A variable structure model reference adaptive control
(VS-MRAC) strategy for active steering assistance of a two wheel
steering car is proposed. An ideal steering system with fixed
properties and moving on an ideal road is used as the reference
model, and the active steering assistance system is forced to attain
the same behavior as the reference model. The proposed system can
treat the nonlinear relationships between the side slip angles and
lateral forces on tire, and the uncertainties on friction of the road
surface, whose compensation are very important under critical
situations. Simulation results show improvements on yaw rate and
side slip.
Abstract: Corrosion of metallic water pipelines buried below
ground surface is a function of the nature of the surrounding soil and
groundwater. This gives the importance of knowing the physical and
chemical characteristics of the pipe-s surrounding environment. The
corrosion of externally – unprotected metallic water pipelines,
specially ductile iron pipes, in localities with aggressive soil
conditions is becoming a significant problem. Anticorrosive
protection for metallic water pipelines, their fittings and accessories
is very important, because they may be attached by corrosion with
time. The tendency of a metallic substrate to corrode is a function of
the surface characteristics of the metal and of the metal/protective
film interface, the physical, electrical and electrochemical properties
of the film, and the nature of the environment in which the pipelines
system is placed. In this work the authors have looked at corrosion
problems of water pipelines and their control. The corrosive
properties of groundwater and soil environments are reviewed, and
parameters affecting corrosion are discussed. The purpose of this
work is to provide guidelines for materials selection in water and soil
environments, and how the water pipelines can be protected against
metallic corrosion.
Abstract: Wall-surface jet induced by the dielectric barrier
discharge (DBD) has been proposed as an actuator for active flow
control in aerodynamic applications. Discharge plasma evolution of
the DBD plasma actuator was simulated based on a simple fluid model,
in which the electron, one type of positive ion and negative ion were
taken into account. Two-dimensional simulation was conducted, and
the results are in agreement with the insights obtained from
experimental studies. The simulation results indicate that the discharge
mode changes depending on applied voltage slope; when the applied
voltage is positive-going with high applied voltage slope, the
corona-type discharge mode turns into the streamer-type discharge
mode and the threshold voltage slope is around 300 kV/ms in this
simulation. The characteristics of the electrohydrodynamic (EHD)
force, which is the source of the wall-surface jet, also change
depending on the discharge mode; the tentative peak value of the EHD
force during the positive-going voltage phase is saturated by the
periodical formation of the streamer-type discharge.
Abstract: Evaporator is an important and widely used heat
exchanger in air conditioning and refrigeration industries. Different
methods have been used by investigators to increase the heat transfer
rates in evaporators. One of the passive techniques to enhance heat
transfer coefficient is the application of microfin tubes. The
mechanism of heat transfer augmentation in microfin tubes is
dependent on the flow regime of two-phase flow. Therefore many
investigations of the flow patterns for in-tube evaporation have been
reported in literatures. The gravitational force, surface tension and
the vapor-liquid interfacial shear stress are known as three dominant
factors controlling the vapor and liquid distribution inside the tube. A
review of the existing literature reveals that the previous
investigations were concerned with the two-phase flow pattern for
flow boiling in horizontal tubes [12], [9]. Therefore, the objective of
the present investigation is to obtain information about the two-phase
flow patterns for evaporation of R-134a inside horizontal smooth and
microfin tubes. Also Investigation of heat transfer during flow
boiling of R-134a inside horizontal microfin and smooth tube have
been carried out experimentally The heat transfer coefficients for
annular flow in the smooth tube is shown to agree well with Gungor
and Winterton-s correlation [4]. All the flow patterns occurred in the
test can be divided into three dominant regimes, i.e., stratified-wavy
flow, wavy-annular flow and annular flow. Experimental data are
plotted in two kinds of flow maps, i.e., Weber number for the vapor
versus weber number for the liquid flow map and mass flux versus
vapor quality flow map. The transition from wavy-annular flow to
annular or stratified-wavy flow is identified in the flow maps.
Abstract: Equipment miniaturisation offers several opportunities such as an increased surface-to-volume ratio and higher heat transfer coefficients. However, moving towards small-diameter channels demands extra attention to fouling, reliability and stable operation of the system. The present investigation explores possibilities to enhance the stability of the once-through micro evaporator by reducing its flow boiling induced pressure fluctuations. Experimental comparison shows that the measured reduction factor approaches a theoretically derived value. Pressure fluctuations are reduced by a factor of ten in the solid conical channel and a factor of 15 in the porous conical channel. This presumably leads to less backflow and therefore to a better flow control.
Abstract: Preliminary results for a new flat plate test
facility are presented here in the form of Computational Fluid Dynamics (CFD), flow visualisation, pressure measurements and thermal anemometry. The results from the CFD and flow
visualisation show the effectiveness of the plate design, with the trailing edge flap anchoring the stagnation point on the working surface and reducing the extent of the leading edge separation. The flow visualization technique demonstrates the
two-dimensionality of the flow in the location where the
thermal anemometry measurements are obtained.
Measurements of the boundary layer mean velocity profiles compare favourably with the Blasius solution, thereby allowing for comparison of future measurements with the
wealth of data available on zero pressure gradient Blasius
flows. Results for the skin friction, boundary layer thickness,
frictional velocity and wall shear stress are shown to agree well with the Blasius theory, with a maximum experimental deviation from theory of 5%. Two turbulence generating grids
have been designed and characterized and it is shown that the turbulence decay downstream of both grids agrees with established correlations. It is also demonstrated that there is
little dependence of turbulence on the freestream velocity.
Abstract: In studying the possibility of using plants as
rhizoremediators, barley and grass mixture which showed resistance
to various concentrations of oil were selected. The minimum
inhibitory effect of oil on these plants by morphological parameters
such as survival of plants, length and biomass of shoot and root
compared with the control was showed. In determining physiological
parameters, a slight decrease in the number of chlorophyll a and b in
the leaves of plants was noted. The differences in the ratio of the total
surface of the roots to the work surface with the growth of plants in
soil with oil in the study of adsorption of the root surface were
showed.
Abstract: A new strategy for oriented immobilization of proteins was proposed. The strategy contains two steps. The first step is to search for a docking site away from the active site on the protein surface. The second step is trying to find a ligand that is able to grasp the targeted site of the protein. To avoid ligand binding to the active site of protein, the targeted docking site is selected to own opposite charges to those near the active site. To enhance the ligand-protein binding, both hydrophobic and electrostatic interactions need to be included. The targeted docking site should therefore contain hydrophobic amino acids. The ligand is then selected through the help of molecular docking simulations. The enzyme α-amylase derived from Aspergillus oryzae (TAKA) was taken as an example for oriented immobilization. The active site of TAKA is surrounded by negatively charged amino acids. All the possible hydrophobic sites on the surface of TAKA were evaluated by the free energy estimation through benzene docking. A hydrophobic site on the opposite side of TAKA-s active site was found to be positive in net charges. A possible ligand, 3,3-,4,4- – Biphenyltetra- carboxylic acid (BPTA), was found to catch TAKA by the designated docking site. Then, the BPTA molecules were grafted onto silica gels and measured the affinity of TAKA adsorption and the specific activity of thereby immobilized enzymes. It was found that TAKA had a dissociation constant as low as 7.0×10-6 M toward the ligand BPTA on silica gel. The increase in ionic strength has little effect on the adsorption of TAKA, which indicated the existence of hydrophobic interaction between ligands and proteins. The specific activity of the immobilized TAKA was compared with the randomly adsorbed TAKA on primary amine containing silica gel. It was found that the orderly immobilized TAKA owns a specific activity twice as high as the one randomly adsorbed by ionic interaction.
Abstract: Super-quadrics can represent a set of implicit surfaces,
which can be used furthermore as primitive surfaces to construct a
complex object via Boolean set operations in implicit surface
modeling. In fact, super-quadrics were developed to create a
parametric surface by performing spherical product on two parametric
curves and some of the resulting parametric surfaces were also
represented as implicit surfaces. However, because not every
parametric curve can be redefined implicitly, this causes only implicit
super-elliptic and super-hyperbolic curves are applied to perform
spherical product and so only implicit super-ellipsoids and
hyperboloids are developed in super-quadrics. To create implicit
surfaces with more diverse shapes than super-quadrics, this paper
proposes an implicit representation of spherical product, which
performs spherical product on two implicit curves like super-quadrics
do. By means of the implicit representation, many new implicit curves
such as polygonal, star-shaped and rose-shaped curves can be used to
develop new implicit surfaces with a greater variety of shapes than
super-quadrics, such as polyhedrons, hyper-ellipsoids, superhyperboloids
and hyper-toroids containing star-shaped and roseshaped
major and minor circles. Besides, the newly developed implicit
surfaces can also be used to define new primitive implicit surfaces for
constructing a more complex implicit surface in implicit surface
modeling.
Abstract: In the present study, development of salbutamol
sulphate nanoparticles that adhere to gastric mucus was investigated.
Salbutamol sulphate has low bioavailability due to short transit time in
gastric. It also has a positive surface charge that provides hurdles to be
encapsulated by the positively strong mucoadhesive polymer of
chitosan. To overcome the difficulties, the surface charge of active
ingredient was modified using several nonionic and anionic
stomach-specific polymers. The nanoparticles were prepared using
ionotropic gelation technique. The evaluation involved determination
of particle size, zeta potential, entrapment efficiency, in vitro drug
release and in vitro mucoadhesion test. Results exhibited that the use
of anionic alginate polymer was more satisfactory than that of
nonionic polymer. Characteristics of the particles was nano-size, high
encapsulation efficiency, fulfilled the drug release requirements and
adhesive towards stomach for around 11 hours. This result shows that
the salbutamol sulphate nanoparticles can be utilized for improvement
its delivery.
Abstract: The heavy metal contamination of the technogenous
sediments and soils at the investigated dump-field show irregular
planar distribution. Also the heavy metal content in the surface water,
drainage water and in the groundwater was studied both in the dry as
well as during the rainy periods. The cementation process causes
substitution of iron by copper. Natural installation and development
of plant species was observed at the old mine waste dumps, specific
to the local chemical conditions such as low content of essential
nutrients and high content of heavy metals. The individual parts of
the plant tissues (roots, branches/stems, leaves/needles, flowers/
fruits) are contaminated by heavy metals and tissues are damaged
differently, respectively.