Abstract: This study focuses on an evaluation of Hokkaido which
is the northernmost and largest prefecture by surface area in Japan and
particularly on two points: the rivalry between all kinds of land use
such as urban land and agricultural and forestry land in various cities
and their surrounding areas and the possibilities for forestry biomass in
areas other than those mentioned above and grasps which areas require
examination of the nature of land use control and guidance through
conducting land use analysis at the district level using GIS
(Geographic Information Systems). The results of analysis in this
study demonstrated that it is essential to divide the whole of Hokkaido
into two areas: those within delineated city planning areas and those
outside of delineated city planning areas and to conduct an evaluation
of each land use control.
In delineated urban areas, particularly urban areas, it is essential to
re-examine land use from the point of view of compact cities or smart
cities along with conducting an evaluation of land use control that
focuses on issues of rivalry between all kinds of land use such as urban
land and agricultural and forestry land. In areas outside of delineated
urban areas, it is desirable to aim to build a specific community
recycling range based on forest biomass utilization by conducting an
evaluation of land use control concerning the possibilities for forest
biomass focusing particularly on forests within and outside of city
planning areas.
Abstract: Response surface methodology with Box–Benhken (BB) design of experiment approach has been utilized to study the mechanism of interface slip damping in layered and jointed tack welded beams with varying surface roughness. The design utilizes the initial amplitude of excitation, tack length and surface roughness at the interfaces to develop the model for the logarithmic damping decrement of the layered and jointed welded structures. Statistically designed experiments have been performed to estimate the coefficients in the mathematical model, predict the response, and check the adequacy of the model. Comparison of predicted and experimental response values outside the design conditions have shown good correspondence, implying that empirical model derived from response surface approach can be effectively used to describe the mechanism of interface slip damping in layered and jointed tack welded structures.
Abstract: FW4 is a newly developed hot die material widely
used in Forging Dies manufacturing. The right selection of the
machining conditions is one of the most important aspects to take
into consideration in the Electrical Discharge Machining (EDM) of
FW4. In this paper an attempt has been made to develop
mathematical models for relating the Material Removal Rate (MRR),
Tool Wear Ratio (TWR) and surface roughness (Ra) to machining
parameters (current, pulse-on time and voltage). Furthermore, a study
was carried out to analyze the effects of machining parameters in
respect of listed technological characteristics. The results of analysis
of variance (ANOVA) indicate that the proposed mathematical
models, can adequately describe the performance within the limits of
the factors being studied.
Abstract: This paper features the proposed modeling and design
of a Robust Decentralized Periodic Output Feedback (RDPOF)
control technique for the active vibration control of smart flexible
multimodel Euler-Bernoulli cantilever beams for a multivariable
(MIMO) case by retaining the first 6 vibratory modes. The beam
structure is modeled in state space form using the concept of
piezoelectric theory, the Euler-Bernoulli beam theory and the Finite
Element Method (FEM) technique by dividing the beam into 4 finite
elements and placing the piezoelectric sensor / actuator at two finite
element locations (positions 2 and 4) as collocated pairs, i.e., as
surface mounted sensor / actuator, thus giving rise to a multivariable
model of the smart structure plant with two inputs and two outputs.
Five such multivariable models are obtained by varying the
dimensions (aspect ratios) of the aluminum beam, thus giving rise to
a multimodel of the smart structure system. Using model order
reduction technique, the reduced order model of the higher order
system is obtained based on dominant eigen value retention and the
method of Davison. RDPOF controllers are designed for the above 5
multivariable-multimodel plant. The closed loop responses with the
RDPOF feedback gain and the magnitudes of the control input are
observed and the performance of the proposed multimodel smart
structure system with the controller is evaluated for vibration control.
Abstract: The paper presents the results of microhardness and
microstructure of low carbon steel surface melted using carbon
dioxide laser with a wavelength of 10.6μm and a maximum output
power of 2000W. The processing parameters such as the laser power,
and the scanning rate were investigated in this study. After surface
melting two distinct regions formed corresponding to the melted zone
MZ, and the heat affected zone HAZ. The laser melted region
displayed a cellular fine structures while the HAZ displayed
martensite or bainite structure. At different processing parameters,
the original microstructure of this steel (Ferrite+Pearlite) has been
transformed to new phases of martensitic and bainitic structures. The
fine structure and the high microhardness are evidence of the high
cooling rates which follow the laser melting. The melting pool and
the transformed microstructure in the laser surface melted region of
carbon steel showed clear dependence on laser power and scanning
rate.
Abstract: Simultaneous Saccharification and Fermentation (SSF) of sugarcane bagasse by cellulase and Pachysolen tannophilus MTCC *1077 were investigated in the present study. Important process variables for ethanol production form pretreated bagasse were optimized using Response Surface Methodology (RSM) based on central composite design (CCD) experiments. A 23 five level CCD experiments with central and axial points was used to develop a statistical model for the optimization of process variables such as incubation temperature (25–45°) X1, pH (5.0–7.0) X2 and fermentation time (24–120 h) X3. Data obtained from RSM on ethanol production were subjected to the analysis of variance (ANOVA) and analyzed using a second order polynomial equation and contour plots were used to study the interactions among three relevant variables of the fermentation process. The fermentation experiments were carried out using an online monitored modular fermenter 2L capacity. The processing parameters setup for reaching a maximum response for ethanol production was obtained when applying the optimum values for temperature (32°C), pH (5.6) and fermentation time (110 h). Maximum ethanol concentration (3.36 g/l) was obtained from 50 g/l pretreated sugarcane bagasse at the optimized process conditions in aerobic batch fermentation. Kinetic models such as Monod, Modified Logistic model, Modified Logistic incorporated Leudeking – Piret model and Modified Logistic incorporated Modified Leudeking – Piret model have been evaluated and the constants were predicted.
Abstract: Humic acids (HAs) have been shown to activate some
ion uptakes along with stimulating the lateral roots at effective
concentration of micronutrients. However, the effects of HA on ion
adsorption by plant roots are not easily explainable due to the
varieties of HAs that differ from origins. Therefore, this study was
aimed to investigate the effect of various concentrations of HA
obtained from the compost derived from mix manures and some
agricultural wastes on the growth of eggplant seedlings (Solanum
melongena L. cv. Chao Praya) in tissue cultures at low nutrient level.
Egg plant seeds were surfaced sterilized and germinated in ½
Murashige and Skoog medium (MS) without HA added or in ¼ MS
supplemented with 0, 25, 50, 75 and 100 ppm of HAs. Then, they
were cultured for 4 weeks under the controlled environment. The
results showed that seedlings grown on ¼MS supplemented with
HAs at the concentration of 25 and 50 ppm had the average plant
heights (2.49 and 2.28 cm, respectively) higher than the other
treatments. Both treatments also significantly showed the maximum
average fresh and dry weights (p
Abstract: The effect of the discontinuity of the rail ends and the
presence of lower modulus insulation material at the gap to the
variations of stresses in the insulated rail joint (IRJ) is presented. A
three-dimensional wheel – rail contact model in the finite element
framework is used for the analysis. It is shown that the maximum stress
occurs in the subsurface of the railhead when the wheel contact occurs
far away from the rail end and migrates to the railhead surface as the
wheel approaches the rail end; under this condition, the interface
between the rail ends and the insulation material has suffered
significantly increased levels of stress concentration. The ratio of the
elastic modulus of the railhead and insulation material is found to alter
the levels of stress concentration. Numerical result indicates that a
higher elastic modulus insulating material can reduce the stress
concentration in the railhead but will generate higher stresses in the
insulation material, leading to earlier failure of the insulation material
Abstract: Generally flow behavior in centrifugal fan is observed
to be in a state of instability with flow separation zones on suction
surface as well as near the front shroud. Overall performance of the
diffusion process in a centrifugal fan could be enhanced by
judiciously introducing the boundary layer suction slots. With easy
accessibility of CFD as an analytical tool, an extensive numerical
whole field analysis of the effect of boundary layer suction slots in
discrete regions of suspected separation points is possible. This paper
attempts to explore the effect of boundary layer suction slots
corresponding to various geometrical locations on the impeller with
converging configurations for the slots. The analysis shows that the
converging suction slots located on the impeller blade about 25%
from the trailing edge, significantly improves the static pressure
recovery across the fan. Also it is found that Slots provided at a
radial distance of about 12% from the leading and trailing edges
marginally improve the static pressure recovery across the fan.
Abstract: Fuzzy controllers are potential candidates for the
control of nonlinear, time variant and also complicated systems. Anti
lock brake system (ABS) which is a nonlinear system, may not be
easily controlled by classical control methods. An intelligent Fuzzy
control method is very useful for this kind of nonlinear system. A
typical antilock brake system (ABS) by sensing the wheel lockup,
releases the brakes for a short period of time, and then reapplies again
the brakes when the wheel spins up. In this paper, an intelligent fuzzy
ABS controller is designed to adjust slipping performance for variety
of roads. There are tow major sections in the proposing control
system. First section consists of tow Fuzzy-Logic Controllers (FLC)
providing optimal brake torque for both front and rear wheels.
Second section which is also a FLC provides required amount of slip
and torque references properties for different kind of roads.
Simulation results of our proposed intelligent ABS for three different
kinds of road show more reliable and better performance in compare
with two other break systems.
Abstract: Dynamics of a vapour bubble generated due to a high local energy input near a circular thin bronze plate in the absence of the buoyancy forces is numerically investigated in this paper. The bubble is generated near a thin bronze plate and during the growth and collapse of the bubble, it deforms the nearby plate. The Boundary Integral Equation Method is employed for numerical simulation of the problem. The fluid is assumed to be incompressible, irrotational and inviscid and the surface tension on the bubble boundary is neglected. Therefore the fluid flow around the vapour bubble can be assumed as a potential flow. Furthermore, the thin bronze plate is assumed to have perfectly plastic behaviour. Results show that the displacement of the circular thin bronze plate has considerable effect on the dynamics of its nearby vapour bubble. It is found that by decreasing the thickness of the thin bronze plate, the growth and collapse rate of the bubble becomes higher and consequently the lifetime of the bubble becomes shorter.
Abstract: Droplet size distributions in the cold spray of a fuel
are important in observed combustion behavior. Specification of
droplet size and velocity distributions in the immediate downstream
of injectors is also essential as boundary conditions for advanced
computational fluid dynamics (CFD) and two-phase spray transport
calculations. This paper describes the development of a new model to
be incorporated into maximum entropy principle (MEP) formalism
for prediction of droplet size distribution in droplet formation region.
The MEP approach can predict the most likely droplet size and
velocity distributions under a set of constraints expressing the
available information related to the distribution.
In this article, by considering the mechanisms of turbulence
generation inside the nozzle and wave growth on jet surface, it is
attempted to provide a logical framework coupling the flow inside the
nozzle to the resulting atomization process. The purpose of this paper
is to describe the formulation of this new model and to incorporate it
into the maximum entropy principle (MEP) by coupling sub-models
together using source terms of momentum and energy. Comparison
between the model prediction and experimental data for a gas turbine
swirling nozzle and an annular spray indicate good agreement
between model and experiment.
Abstract: A passive system "Qanat" is collection of some
underground wells. A mother-well was dug in a place far from the
city where they could reach to the water table maybe 100 meters
underground, they dug other wells to direct water toward the city,
with minimum possible gradient. Using the slope of the earth they
could bring water close to the surface in the city. The source of water
or the appearance of Qanat, land slope and the ownership lines are
the important and effective factors in the formation of routes and the
segment division of lands to the extent that making use of Qanat as
the techniques of extracting underground waters creates a channel of
routes with an organic order and hierarchy coinciding the slope of
land and it also guides the Qanat waters in the tradition texture of salt
desert and border provinces of it. Qanats are excavated in a specified
distinction from each other. The quantity of water provided by
Qanats depends on the kind of land, distance from mountain,
geographical situation of them and the rate of water supply from the
underground land. The rate of underground waters, possibility of
Qanat excavation, number of Qanats and rate of their water supply
from one hand and the quantity of cultivable fertile lands from the
other hand are the important natural factors making the size of cities.
In the same manner the cities with several Qanats have multi central
textures. The location of cities is in direct relation with land quality,
soil fertility and possibility of using underground water by excavating
Qanats. Observing the allowable distance for Qanat watering is a
determining factor for distance between villages and cities.
Topography, land slope, soil quality, watering system, ownership,
kind of cultivation, etc. are the effective factors in directing Qanats
for excavation and guiding water toward the cultivable lands and it
also causes the formation of different textures in land division of
farming provinces. Several divisions such as orderly and wide, inorderly,
thin and long, comb like, etc. are the introduction to organic
order. And at the same time they are complete coincidence with
environmental conditions in the typical development of ecological
architecture and planning in the traditional cities and settlements
order.
Abstract: Simultaneous effects of temperature, immersion time, salt concentration, sucrose concentration, pressure and convective dryer temperature on the combined osmotic dehydration - convective drying of edible button mushrooms were investigated. Experiments were designed according to Central Composite Design with six factors each at five different levels. Response Surface Methodology (RSM) was used to determine the optimum processing conditions that yield maximum water loss and rehydration ratio and minimum solid gain and shrinkage in osmotic-convective drying of edible button mushrooms. Applying surfaces profiler and contour plots optimum operation conditions were found to be temperature of 39 °C, immersion time of 164 min, salt concentration of 14%, sucrose concentration of 53%, pressure of 600 mbar and drying temperature of 40 °C. At these optimum conditions, water loss, solid gain, rehydration ratio and shrinkage were found to be 63.38 (g/100 g initial sample), 3.17 (g/100 g initial sample), 2.26 and 7.15%, respectively.
Abstract: All over the world, including the Middle and East
European countries, sustainable tillage and sowing technologies are
applied increasingly broadly with a view to optimising soil resources,
mitigating soil degradation processes, saving energy resources,
preserving biological diversity, etc. As a result, altered conditions of
tillage and sowing technological processes are faced inevitably. The
purpose of this study is to determine the seedbed topsoil hardness
when using a combined sowing coulter in different sustainable tillage
technologies. The research involved a combined coulter consisting
of two dissected blade discs and a shoe coulter. In order to determine
soil hardness at the seedbed area, a multipenetrometer was used. It
was found by experimental studies that in loosened soil, a combined
sowing coulter equally suppresses the furrow bottom, walls and soil
near the furrow; therefore, here, soil hardness was similar at all
researched depths and no significant differences were established. In
loosened and compacted (double-rolled) soil, the impact of a
combined coulter on the hardness of seedbed soil surface was more
considerable at a depth of 2 mm. Soil hardness at the furrow bottom
and walls to a distance of up to 26 mm was 1.1 MPa. At a depth of 10
mm, the greatest hardness was established at the furrow bottom. In
loosened and heavily compacted (rolled for 6 times) soil, at a depth
of 2 and 10 mm a combined coulter most of all compacted the furrow
bottom, which has a hardness of 1.8 MPa. At a depth of 20 mm, soil
hardness within the whole investigated area varied insignificantly and
fluctuated by around 2.0 MPa. The hardness of furrow walls and soil
near the furrow was by approximately 1.0 MPa lower than that at the
furrow bottom
Abstract: The reliable results of an insulated oval duct
considering heat radiation are obtained basing on accurate oval
perimeter obtained by integral method as well as one-dimensional
Plane Wedge Thermal Resistance (PWTR) model. This is an extension
study of former paper of insulated oval duct neglecting heat radiation.
It is found that in the practical situations with long-short-axes ratio a/b
4.5% while t/R2
Abstract: Financial forecasting is an example of signal processing problems. A number of ways to train/learn the network are available. We have used Levenberg-Marquardt algorithm for error back-propagation for weight adjustment. Pre-processing of data has reduced much of the variation at large scale to small scale, reducing the variation of training data.
Abstract: Chemical and physical functionalization of multiwalled
carbon nanotubes (MWCNT) has been commonly practiced to
achieve better dispersion of carbon nanotubes (CNTs) in polymer
matrix. This work describes various functionalization methods (acidtreatment,
non-ionic surfactant treatment with TritonX-100),
fabrication of MWCNT/PP nanocomposites via melt blending and
characterization of mechanical properties. Microscopy analysis
(FESEM, TEM, XPS) showed effective purification of MWCNTs
under acid treatment, and better dispersion under both chemical and
physical functionalization techniques combined, in their respective
order. Tensile tests showed increase in tensile strength for the
nanocomposites that contain MWCNTs up to 2 wt%. A decrease in
tensile strength was seen in samples that contain 4 wt% of MWCNTs
for both raw and Triton X-100 functionalized, signifying MWCNT
degradation/rebundling at composition with higher content of
MWCNTs. For the acid-treated MWCNTs, however, the tensile
results showed slight improvement even at 4wt%, indicating effective
dispersion of MWCNTs.
Abstract: Nowadays, the increase of human population every
year results in increasing of water usage and demand. Saen Saep
canal is important canal in Bangkok. The main objective of this study
is using Artificial Neural Network (ANN) model to estimate the
Chemical Oxygen Demand (COD) on data from 11 sampling sites.
The data is obtained from the Department of Drainage and Sewerage,
Bangkok Metropolitan Administration, during 2007-2011. The
twelve parameters of water quality are used as the input of the
models. These water quality indices affect the COD. The
experimental results indicate that the ANN model provides a high
correlation coefficient (R=0.89).
Abstract: The present work analyses different parameters of pressure die casting to minimize the casting defects. Pressure diecasting is usually applied for casting of aluminium alloys. Good surface finish with required tolerances and dimensional accuracy can be achieved by optimization of controllable process parameters such as solidification time, molten temperature, filling time, injection pressure and plunger velocity. Moreover, by selection of optimum process parameters the pressure die casting defects such as porosity, insufficient spread of molten material, flash etc. are also minimized. Therefore, a pressure die casting component, carburetor housing of aluminium alloy (Al2Si2O5) has been considered. The effects of selected process parameters on casting defects and subsequent setting of parameters with the levels have been accomplished by Taguchi-s parameter design approach. The experiments have been performed as per the combination of levels of different process parameters suggested by L18 orthogonal array. Analyses of variance have been performed for mean and signal-to-noise ratio to estimate the percent contribution of different process parameters. Confidence interval has also been estimated for 95% consistency level and three conformational experiments have been performed to validate the optimum level of different parameters. Overall 2.352% reduction in defects has been observed with the help of suggested optimum process parameters.