Abstract: In this paper, the influencing parameters of a novel
purely mechanical wireless in-mould injection moulding sensor
were investigated. The sensor is capable of detecting the melt
front at predefined locations inside the mould. The sensor comprises
a movable pin which acts as the sensor element generating
structure-borne sound triggered by the passing melt front. Due to
the sensor design, melt pressure is the driving force. For pressure
level measurement during pin movement a pressure transducer
located at the same position as the movable pin. By deriving
a mathematical model for the mechanical movement, dominant
process parameters could be investigated towards their impact
on the melt front detection characteristic. It was found that the
sensor is not affected by the investigated parameters enabling it
for reliable melt front detection. In addition, it could be proved
that the novel sensor is in comparable range to conventional melt
front detection sensors.
Abstract: One of the difficulties of the vibration-based damage identification methods is the nonuniqueness of the results of damage identification. The different damage locations and severity may cause the identical response signal, which is even more severe for detection of the multiple damage. This paper proposes a new strategy for damage detection to avoid this nonuniqueness. This strategy firstly determines the approximates damage area based on the statistical pattern recognition method using the dynamic strain signal measured by the distributed fiber Bragg grating, and then accurately evaluates the damage information based on the Bayesian model updating method using the experimental modal data. The stochastic simulation method is then used to compute the high-dimensional integral in the Bayesian problem. Finally, an experiment of the plate structure, simulating one part of mechanical structure, is used to verify the effectiveness of this approach.
Abstract: The paper deals with the analysis of triggering
conditions and evolution processes of piping phenomena, in relation
to both mechanical and hydraulic aspects. In particular, the aim of
the study is to predict slope instabilities triggered by piping,
analysing the conditions necessary for a flow failure to occur. Really,
the mechanical effect involved in the loads redistribution around the
pipe is coupled to the drainage process arising from higher
permeability of the pipe. If after the pipe formation, the drainage
goes prevented for pipe clogging, the porewater pressure increase can
lead to the failure or even the liquefaction, with a subsequent flow
slide. To simulate the piping evolution and to verify relevant stability
conditions, a iterative coupled modelling approach has been pointed
out. As example, the proposed tool has been applied to the Stava
Valley disaster (July, 1985), demonstrating that piping might be one
of triggering phenomena of the tailings dams collapse.
Abstract: Sports Sciences has been historically supported by the positivism idea of science, especially by the mechanistic/reductionist and becomes a field that views experimentation and measurement as the mayor research domains. The disposition to simplify nature and the world by parts has fragmented and reduced the idea of bodyathletes as machine. In this paper we intent to re-think this perception lined by Complexity Theory. We come with the idea of athletes as a reflexive and active being (corporeity-body). Therefore, the construction of a training that considers the cultural, biological, psychological elements regarding the experience of the human corporal movements in a circumspect and responsible way could bring better chances of accomplishment. In the end, we hope to help coaches understand the intrinsic complexity of the body they are training, how better deal with it, and, in the field of a deep globalization among the different types of knowledge, to respect and accepted the peculiarities of knowledge that comprise this area.
Abstract: Wireless Sensor Networks (WSNs) are used to monitor/observe vast inaccessible regions through deployment of large number of sensor nodes in the sensing area. For majority of WSN applications, the collected data needs to be combined with geographic information of its origin to make it useful for the user; information received from remote Sensor Nodes (SNs) that are several hops away from base station/sink is meaningless without knowledge of its source. In addition to this, location information of SNs can also be used to propose/develop new network protocols for WSNs to improve their energy efficiency and lifetime. In this paper, range free localization protocols for WSNs have been proposed. The proposed protocols are based on weighted centroid localization technique, where the edge weights of SNs are decided by utilizing fuzzy logic inference for received signal strength and link quality between the nodes. The fuzzification is carried out using (i) Mamdani, (ii) Sugeno, and (iii) Combined Mamdani Sugeno fuzzy logic inference. Simulation results demonstrate that proposed protocols provide better accuracy in node localization compared to conventional centroid based localization protocols despite presence of unintentional radio frequency interference from radio frequency (RF) sources operating in same frequency band.
Abstract: The paper provides a discussion of the most relevant
aspects of yield curve modeling. Two classes of models are
considered: stochastic and parsimonious function based, through the
approaches developed by Vasicek (1977) and Nelson and Siegel
(1987). Yield curve estimates for Croatia are presented and their
dynamics analyzed and finally, a comparative analysis of models is
conducted.
Abstract: Water is the key of national development. Wherever a spring has been dried out or a river has changed its course, the area-s people have migrated and have been scattered and the area-s civilization has lost its brilliance. Today, air pollution, global warming and ozone layer damage are as the problems of countries, but certainly in the next decade the shortage and pollution of waters will be important issues of the world. The polluted waters are more dangerous in when they are used in agriculture. Because they infect plants and these plants are used in human and livestock consumption in food chain. With the increasing population growth and after that, the increase need to facilities and raw materials, human beings has started to do haste actions and wanted or unwanted destroyed his life basin. They try to overuse and capture his environment extremely, instead of having futurism approach in sustainable use of nature. This process includes Zayanderood recession, and caused its pollution after the transition from industrial and urban areas. Zayandehrood River in Isfahan is a vital artery of a living ecosystem. Now is the location of disposal waste water of many cities, villages and existing industries. The central area of the province is an important industrial place, and its environmental situation has reached a critical stage. Not only a large number of pollution-generating industries are active in the city limits, but outside of the city and adjacent districts Zayandehrood River, heavy industries like steel, Mobarakeh Steel and other tens great units pollute wild life. This article tries to study contaminant sources of Zayanderood and their severity, and determine and discuss the share of each of these resources by major industrial centers located in areas. At the end, we represent suitable strategy.
Abstract: This paper reports work done to improve the modeling of complex processes when only small experimental data sets are available. Neural networks are used to capture the nonlinear underlying phenomena contained in the data set and to partly eliminate the burden of having to specify completely the structure of the model. Two different types of neural networks were used for the application of Pulping of Sugar Maple problem. A three layer feed forward neural networks, using the Preconditioned Conjugate Gradient (PCG) methods were used in this investigation. Preconditioning is a method to improve convergence by lowering the condition number and increasing the eigenvalues clustering. The idea is to solve the modified problem where M is a positive-definite preconditioner that is closely related to A. We mainly focused on Preconditioned Conjugate Gradient- based training methods which originated from optimization theory, namely Preconditioned Conjugate Gradient with Fletcher-Reeves Update (PCGF), Preconditioned Conjugate Gradient with Polak-Ribiere Update (PCGP) and Preconditioned Conjugate Gradient with Powell-Beale Restarts (PCGB). The behavior of the PCG methods in the simulations proved to be robust against phenomenon such as oscillations due to large step size.
Abstract: One part of the total employee’s reward is apart from basic wages or salary, employee’s benefits and intangible remuneration also so called contingent (variable) pay. Contingent pay is connected to performance, contribution, cap competency or skills of individual employees, and to team’s or company-wide performance or to combination of few of the mentioned possibilities. Sometimes among the contingent pay is also incorporated the remuneration based on length of employment, when the financial reward is not connected to performance or skills, but to length of continuous employment either on one working position or in one level of remuneration scale. Main aim of this article is to define, based on available information, contingent pay, describe individual forms, its advantages and disadvantages and possibilities to utilization in practice; but also bring information not only about its extent and level of utilization of contingent pay by companies in one of the Czech Republic’s regions, but also mention their practical experience with this type of remuneration.
Abstract: The lack of inclusive housing in Australia contributes
to the marginalization and exclusion of people with disability and
older people from family and community life. The Australian
government has handed over the responsibility of increasing the
supply of inclusive housing to the housing industry through an agreed
national access standard and a voluntary strategy. Voluntary
strategies have not been successful in other constituencies and little is
known about what would work in Australia today. Findings from a
research project into the voluntariness of the housing industry
indicate that a reliable and consistent supply is unlikely without an
equivalent increase in demand. The strategy has, however, an
important role to play in the task of changing housing industry
practices towards building more inclusive communities.
Abstract: This paper examines the interplay of policy options
and cost-effective technology in providing sustainable distance
education. A case study has been conducted among the learners and
teachers. The emergence of learning technologies through CD,
internet, and mobile is increasingly adopted by distance institutes for
quick delivery and cost-effective factors. Their sustainability is
conditioned by the structure of learners and well as the teaching
community. The structure of learners in terms of rural and urban
background revealed similarity in adoption and utilization of mobile
learning. In other words, the technology transcended the rural-urban
dichotomy. The teaching community was divided into two groups on
policy issues. This study revealed both cost-effective as well as
sustainability impacts on different learners groups divided by rural
and urban location.
Abstract: In this contribution is presented a complex design of
individual objects identification in the workplace of intelligent
assembly cell. Intelligent assembly cell is situated at Institute of
Manufacturing Systems and Applied Mechanics and is used for
pneumatic actuator assembly. Pneumatic actuator components are
pneumatic roller, cover, piston and spring. Two identification objects
alternatives for assembly are designed in the workplace of industrial
robot. In the contribution is evaluated and selected suitable
alternative for identification – 2D codes reader. The complex design
of individual object identification is going out of intelligent
manufacturing systems knowledge.
Intelligent assembly and manufacturing systems as systems of
new generation are gradually loaded in to the mechanical production,
when they are removeing human operation out of production process
and they also short production times.
Abstract: The article deals with the problems of political and
economic processes in Kazakhstan since independence in the context
of globalization. It analyzes the geopolitical situation and selfpositioning
processes in the world after the end of the "cold war". It
examines the problems of internal economization of the Republic for
20 years of independence. The authors argue that the reforms
proceeded in the economic sphere have brought ambiguous and
tangible results. Despite the difficult economic and political conditions
facing a world economical crisis the country has undergone
fundamental and radical transformations in the whole socio-economic
system
Abstract: Robust face recognition under various illumination
environments is very difficult and needs to be accomplished for
successful commercialization. In this paper, we propose an improved
illumination normalization method for face recognition. Illumination
normalization algorithm based on anisotropic smoothing is well known
to be effective among illumination normalization methods but
deteriorates the intensity contrast of the original image, and incurs less
sharp edges. The proposed method in this paper improves the previous
anisotropic smoothing-based illumination normalization method so
that it increases the intensity contrast and enhances the edges while
diminishing the effect of illumination variations. Due to the result of
these improvements, face images preprocessed by the proposed
illumination normalization method becomes to have more distinctive
feature vectors (Gabor feature vectors) for face recognition. Through
experiments of face recognition based on Gabor feature vector
similarity, the effectiveness of the proposed illumination
normalization method is verified.
Abstract: Medical Surgical Nursing is one of the major subjects
in nursing. This study examined the validity and reliability of the
achievement examination utilizing the Classical Test Theory and
Item Response Theory. The study answered the following objectives
specifically : ( a) To establish the validity and reliability of the
achievement examination utilizing Classical Test Theory and Item
Response Theory ; ( b ) To determine the dimensionality measure of
items and ( c ) to compare the item difficulty and item discrimination
of the Medical Surgical Nursing Achievement examination using
Classical Test Theory ( CTT ) and Item Response Theory ( IRT ).
The developed instrument was administered to fourth year nursing
students (N= 136) of a private university in Manila. The findings
yielded the following results: The achievement examination is
reliable both using CTT and IRT. The findings indicate person and
item statistics from two frameworks are quite alike. The achievement
examination formed a unidimensional construct.
Abstract: Natural frequencies and dynamic response of a spur
gear sector are investigated using a two dimensional finite element
model that offers significant advantages for dynamic gear analyses.
The gear teeth are analyzed for different operating speeds. A primary
feature of this modeling is determination of mesh forces using a
detailed contact analysis for each time step as the gears roll through
the mesh. ANSYS software has been used on the proposed model to
find the natural frequencies by Block Lanczos technique and
displacements and dynamic stresses by transient mode super position
method. The effect of rotational speed of the gear on the dynamic
response of gear tooth has been studied and design limits have been
discussed.
Abstract: With the advent of digital cinema and digital
broadcasting, copyright protection of video data has been one of the
most important issues.
We present a novel method of watermarking for video image data
based on the hardware and digital wavelet transform techniques and
name it as “traceable watermarking" because the watermarked data is
constructed before the transmission process and traced after it has been
received by an authorized user.
In our method, we embed the watermark to the lowest part of each
image frame in decoded video by using a hardware LSI.
Digital Cinema is an important application for traceable
watermarking since digital cinema system makes use of watermarking
technology during content encoding, encryption, transmission,
decoding and all the intermediate process to be done in digital cinema
systems. The watermark is embedded into the randomly selected
movie frames using hash functions.
Embedded watermark information can be extracted from the
decoded video data. For that, there is no need to access original movie
data. Our experimental results show that proposed traceable
watermarking method for digital cinema system is much better than the
convenient watermarking techniques in terms of robustness, image
quality, speed, simplicity and robust structure.
Abstract: Shoots, with three leaves, of Paphiopedilum 'Delrosi'
were used as explants for multiple shoot induction. Modified
Hyponex medium was supplemented with thidiazuron (TDZ), N6-
benzyladenine (BA) or kinetin (Kn) alone and in combinations with
2,4-dichlorophenoxyacetic acid (2,4-D). All explants were cultured
for 15 weeks. It was found that TDZ alone at the concentration of
0.45μM or in combination with 4.52μM 2,4-D and 8.88μM BA in
combination with 13.56μM 2,4-D promoted multiple shoots. The
highest shoot sprouting efficiencies (80.0, 90.0 and 80.0%) and new
shoot numbers (1.5, 1.3 and 1.1) were obtained, respectively. Fresh
weight, height, numbers of leaf and root of new shoots and initial
explants were discussed.
Abstract: An Automated Rapid Maxillary Expander (ARME) is
a specially designed microcontroller-based orthodontic appliance to
overcome the shortcomings imposed by the traditional maxillary
expansion appliances. This new device is operates by automatically
widening the maxilla (upper jaw) by expanding the midpalatal suture
[1]. The ARME appliance that has been developed is a combination
of modified butterfly expander appliance, micro gear, micro motor,
and microcontroller to automatically produce light and continuous
pressure to expand the maxilla. For this study, the functionality of the
system is verified through laboratory tests by measure the forced
applied to the teeth each time the maxilla expands. The laboratory
test results show that the developed appliance meets the desired
performance specifications consistently.
Abstract: A novel nanofinishing process using improved ball
end magnetorheological (MR) finishing tool was developed for finishing of flat as well as 3D surfaces of ferromagnetic and non ferromagnetic workpieces. In this process a magnetically controlled
ball end of smart MR polishing fluid is generated at the tip surface of
the tool which is used as a finishing medium and it is guided to
follow the surface to be finished through computer controlled 3-axes
motion controller. The experiments were performed on ferromagnetic
workpiece surface in the developed MR finishing setup to study the effect of finishing time on final surface roughness. The performance
of present finishing process on final finished surface roughness was studied. The surface morphology was observed under scanning
electron microscopy and atomic force microscope. The final surface finish was obtained as low as 19.7 nm from the initial surface
roughness of 142.9 nm. The outcome of newly developed finishing process can be found useful in its applications in aerospace,
automotive, dies and molds manufacturing industries, semiconductor and optics machining etc.