Abstract: The building sector is the largest energy consumer and
CO2 emitter in the European Union (EU) and therefore the active
reduction of energy consumption and elimination of energy wastage
are among the main goals in it. Healthy housing and energy
efficiency are affected by many factors which set challenges to
monitoring, control and research of indoor air quality (IAQ) and
energy consumption, especially in old buildings. These challenges
include measurement and equipment costs, for example.
Additionally, the measurement results are difficult to interpret and
their usage in the ventilation control is also limited when taking into
account the energy efficiency of housing at the same time. The main
goal of this study is to develop a cost-effective building monitoring
and control system especially for old buildings. The starting point or
keyword of the development process is a wireless system; otherwise
the installation costs become too high. As the main result, this paper
describes an idea of a wireless building monitoring and control
system. The first prototype of the system has been installed in 10
residential buildings and in 10 school buildings located in the City of
Kuopio, Finland.
Abstract: Attitude control of aerospace system with liquid containers may face to a problem associate with fuel sloshing. The sloshing phenomena can degrade the stability of control system and in the worst case, interaction between the attitude control system and fuel vibration leading to resonance. In this paper, a full process of nonlinear dynamic modeling of an aerospace launch vehicle with fuel sloshing is given. Then, a new control system based on model reference adaptive filter is proposed and its algorithm is extracted. This controller implemented on the main attitude control system. Finally, numerical simulation of nonlinear model and control system is carried out to examine the performance of the new controller. Results of simulations show that the inconvenient effects of the fuel sloshing by augmenting this control system are reduced and attitude control system performs, satisfactorily.
Abstract: Simultaneous effects of temperature, immersion time, salt concentration, sucrose concentration, pressure and convective dryer temperature on the combined osmotic dehydration - convective drying of edible button mushrooms were investigated. Experiments were designed according to Central Composite Design with six factors each at five different levels. Response Surface Methodology (RSM) was used to determine the optimum processing conditions that yield maximum water loss and rehydration ratio and minimum solid gain and shrinkage in osmotic-convective drying of edible button mushrooms. Applying surfaces profiler and contour plots optimum operation conditions were found to be temperature of 39 °C, immersion time of 164 min, salt concentration of 14%, sucrose concentration of 53%, pressure of 600 mbar and drying temperature of 40 °C. At these optimum conditions, water loss, solid gain, rehydration ratio and shrinkage were found to be 63.38 (g/100 g initial sample), 3.17 (g/100 g initial sample), 2.26 and 7.15%, respectively.
Abstract: The new technology of fuzzy neural networks for identification of parameters for mathematical models of geofields is proposed and checked. The effectiveness of that soft computing technology is demonstrated, especially in the early stage of modeling, when the information is uncertain and limited.
Abstract: A methodology to design a nonlinear observer in a
bond graph approach is proposed. The class of nonlinear observer
with multivariable nonlinearities is considered. A junction structure
of the bond graph observer is proposed. The proposed methodology
to an electrical transformer and a DC motor including the nonlinear
saturation is applied. Nonlinear observers for the transformer and DC
motor based on multivariable circle criterion in the physical domain
are proposed. In order to show the saturation effects on the
transformer and DC motor, simulation results are obtained. Finally,
the paper describes that convergence of the estimates to the true
states is achieved.
Abstract: In order to alleviate the mental and physical problems
of persons with disabilities, animal-assisted therapy (AAT) is one of
the possible modalities that employs the merit of the human-animal
interaction. Nevertheless, to achieve the purpose of AAT for persons
with severe disabilities (e.g. spinal cord injury, stroke, and
amyotrophic lateral sclerosis), real-time animal language
interpretation is desirable. Since canine behaviors can be visually
notable from its tail, this paper proposes the automatic real-time
interpretation of canine tail language for human-canine interaction in
the case of persons with severe disabilities. Canine tail language is
captured via two 3-axis accelerometers. Directions and frequencies
are selected as our features of interests. The novel fuzzy rules based
on Gaussian-Trapezoidal model and center of gravity (COG)-based
defuzzification method are proposed in order to interpret the features
into four canine emotional behaviors, i.e., agitate, happy, scare and
neutral as well as its blended emotional behaviors. The emotional
behavior model is performed in the simulated dog and has also been
evaluated in the real dog with the perfect recognition rate.
Abstract: The energy consumption and delay in read/write
operation of conventional SRAM is investigated analytically as well
as by simulation. Explicit analytical expressions for the energy
consumption and delay in read and write operation as a function of
device parameters and supply voltage are derived. The expressions are
useful in predicting the effect of parameter changes on the energy
consumption and speed as well as in optimizing the design of
conventional SRAM. HSPICE simulation in standard 0.25μm CMOS
technology confirms precision of analytical expressions derived from
this paper.
Abstract: Detection of squirrel cage induction motor (SCIM) broken bars has long been an important but difficult job in the detection area of motor faults. Early detection of this abnormality in the motor would help to avoid costly breakdowns. A new detection method based on particle swarm optimization (PSO) is presented in this paper. Stator current in an induction motor will be measured and characteristic frequency components of faylted rotor will be detected by minimizing a fitness function using pso. Supply frequency and side band frequencies and their amplitudes can be estimated by the proposed method. The proposed method is applied to a faulty motor with one and two broken bars in different loading condition. Experimental results prove that the proposed method is effective and applicable.
Abstract: Nowadays, hand vein recognition has attracted more attentions in identification biometrics systems. Generally, hand vein image is acquired with low contrast and irregular illumination. Accordingly, if you have a good preprocessing of hand vein image, we can easy extracted the feature extraction even with simple binarization. In this paper, a proposed approach is processed to improve the quality of hand vein image. First, a brief survey on existing methods of enhancement is investigated. Then a Radon Like features method is applied to preprocessing hand vein image. Finally, experiments results show that the proposed method give the better effective and reliable in improving hand vein images.
Abstract: This research investigates the suitability of fuel oil in
improving gypseous soil. A detailed laboratory tests were carried-out
on two soils (soil I with 51.6% gypsum content, and soil II with
26.55%), where the two soils were obtained from Al-Therthar site
(Al-Anbar Province-Iraq).
This study examines the improvement of soil properties using the
gypsum material which is locally available with low cost to minimize
the effect of moisture on these soils by using the fuel oil. This study
was conducted on two models of the soil gypsum, from the Tharthar
area. The first model was sandy soil with Gypsum content of (51.6%)
and the second is clayey soil and the content of Gypsum is (26.55%).
The program included tests measuring the permeability and
compressibility of the soil and their collapse properties. The shear
strength of the soil and the amounts of weight loss of fuel oil due to
drying had been found. These tests have been conducted on the
treated and untreated soils to observe the effect of soil treatment on
the engineering properties when mixed with varying degrees of fuel
oil with the equivalent of the water content.
The results showed that fuel oil is a good material to modify the
basic properties of the gypseous soil of collapsibility and
permeability, which are the main problems of this soil and retained
the soil by an appropriate amount of the cohesion suitable for
carrying the loads from the structure.
Abstract: We study the typical domain size and configuration
character of a randomly perturbed system exhibiting continuous
symmetry breaking. As a model system we use rod-like objects
within a cubic lattice interacting via a Lebwohl–Lasher-type
interaction. We describe their local direction with a headless unit
director field. An example of such systems represents nematic LC or
nanotubes. We further introduce impurities of concentration p, which
impose the random anisotropy field-type disorder to directors. We
study the domain-type pattern of molecules as a function of p,
anchoring strength w between a neighboring director and impurity,
temperature, history of samples. In simulations we quenched the
directors either from the random or homogeneous initial
configuration. Our results show that a history of system strongly
influences: i) the average domain coherence length; and ii) the range
of ordering in the system. In the random case the obtained order is
always short ranged (SR). On the contrary, in the homogeneous case,
SR is obtained only for strong enough anchoring and large enough
concentration p. In other cases, the ordering is either of quasi long
range (QLR) or of long range (LR). We further studied memory
effects for the random initial configuration. With increasing external
ordering field B either QLR or LR is realized.
Abstract: The flow field and the motion of the free surface in an
oscillating container are simulated numerically to assess the numerical
approach for studying two-phase flows under oscillating conditions.
Two numerical methods are compared: one is to model the oscillating
container directly using the moving grid of the ALE method, and the
other is to simulate the effect of container motion using the oscillating
body force acting on the fluid in the stationary container. The
two-phase flow field in the container is simulated using the level set
method in both cases. It is found that the calculated results by the body
force method coinsides with those by the moving grid method and the
sloshing behavior is predicted well by both the methods. Theoretical
back ground and limitation of the body force method are discussed,
and the effects of oscillation amplitude and frequency are shown.
Abstract: As known, the guard wires of overhead high voltage
are usually grounded through the grounding systems of support and
of the terminal stations. They do affect the zero sequence impedance
value of the line, Z0, which is generally, calculated assuming that the
wires guard are at ground potential. In this way it is not considered
the effect of the resistances of earth of supports and stations. In this
work is formed a formula for the calculation of Z0 which takes
account of said resistances. Is also proposed a method of calculating
the impedance zero sequence overhead lines in which, in various
sections or spans, the guard wires are connected to the supports, or
isolated from them, or are absent. Parametric analysis is given for
lines 220 kV and 400 kV, which shows the extent of the errors made
with traditional methods of calculation.
Abstract: Modeling of a manufacturing system enables one to
identify the effects of key design parameters on the system performance and as a result to make correct decision. This paper
proposes a manufacturing system modeling approach using a spreadsheet model based on queuing network theory, in which a
static capacity planning model and stochastic queuing model are integrated. The model was used to improve the existing system utilization in relation to product design. The model incorporates few
parameters such as utilization, cycle time, throughput, and batch size.
The study also showed that the validity of developed model is good enough to apply and the maximum value of relative error is 10%, far
below the limit value 32%. Therefore, the model developed in this
study is a valuable alternative model in evaluating a manufacturing system
Abstract: In this paper we present discretization and decomposition methods for a multi-component transport model of a chemical vapor deposition (CVD) process. CVD processes are used to manufacture deposition layers or bulk materials. In our transport model we simulate the deposition of thin layers. The microscopic model is based on the heavy particles, which are derived by approximately solving a linearized multicomponent Boltzmann equation. For the drift-process of the particles we propose diffusionreaction equations as well as for the effects of heat conduction. We concentrate on solving the diffusion-reaction equation with analytical and numerical methods. For the chemical processes, modelled with reaction equations, we propose decomposition methods and decouple the multi-component models to simpler systems of differential equations. In the numerical experiments we present the computational results of our proposed models.
Abstract: Key performance indicators (KPIs) are used for post
result evaluation in the construction industry, and they normally do
not have provisions for changes. This paper proposes a set of
dynamic key performance indicators (d-KPIs) which predicts the
future performance of the activity being measured and presents the
opportunity to change practice accordingly. Critical to the
predictability of a construction project is the ability to achieve
automated data collection. This paper proposes an effective way to
collect the process and engineering management data from an
integrated construction management system. The d-KPI matrix,
consisting of various indicators under seven categories, developed
from this study can be applied to close monitoring of the
development projects of aged-care facilities. The d-KPI matrix also
enables performance measurement and comparison at both project
and organization levels.
Abstract: In this paper, we analyze the effect of noise in a single- ended input differential amplifier working at high frequencies. Both extrinsic and intrinsic noise are analyzed using time domain method employing techniques from stochastic calculus. Stochastic differential equations are used to obtain autocorrelation functions of the output noise voltage and other solution statistics like mean and variance. The analysis leads to important design implications and suggests changes in the device parameters for improved noise characteristics of the differential amplifier.
Abstract: The effect of teaching method on learning
assistance Dunn Review .The study, to compare the effects of
collaboration on teaching mathematics learning courses, including
writing, science, experimental girl students by other methods of
teaching basic first paid and the amount of learning students
methods have been trained to cooperate with other students with
other traditional methods have been trained to compare. The
survey on 100 students in Tehran that using random sampling ¬
cluster of girl students between the first primary selections was
performed. Considering the topic of semi-experimental research
methods used to practice the necessary information by
questionnaire, examination questions by the researcher, in
collaboration with teachers and view authority in this field and
related courses that teach these must have been collected.
Research samples to test and control groups were divided.
Experimental group and control group collaboration using
traditional methods of mathematics courses, including writing and
experimental sciences were trained. Research results using
statistical methods T is obtained in two independent groups show
that, through training assistance will lead to positive results and
student learning in comparison with traditional methods, will
increase also led to collaboration methods increase skills to solve
math lesson practice, better understanding and increased skill
level of students in practical lessons such as science and has been
writing.
Abstract: Malaysian corporations going global increased
many folds. The shift from domestic to international operations
requires increased expatriation to achieve global business goals.
Therefore, this study aims to identify the determinants for success
in expatriation of Malaysian international corporations. There are
certain attributes necessary for a global employee to succeed in
international assignment. Self-administered questionnaires were
sent to 327 respondents with a response rate of 35.2 percent. The
results indicated that most Malaysian manufacturers are involved
in expatriation. For a global employee to succeed in an
international assignment, the ability to work in international teams
was identified and ranked as the most important factor in
determining the effectiveness of expatriation followed by language
proficiency, adaptability to the international assignment and
expatriate sensitivity to cultural elements. The results support
previous research with regard to the importance of an effective
expatriation selection process in order for a company-s
international expansion strategy to succeed.
Abstract: This research simulates one of the natural phenomena,
the ocean wave. Our goal is to be able to simulate the ocean wave at
real-time rate with the water surface interacting with objects. The
wave in this research is calm and smooth caused by the force of the
wind above the ocean surface. In order to make the simulation of the
wave real-time, the implementation of the GPU and the
multithreading techniques are used here. Based on the fact that the
new generation CPUs, for personal computers, have multi cores, they
are useful for the multithread. This technique utilizes more than one
core at a time. This simulation is programmed by C language with
OpenGL. To make the simulation of the wave look more realistic, we
applied an OpenGL technique called cube mapping (environmental
mapping) to make water surface reflective and more realistic.