Abstract: This paper proposes strategies in level crossing (LC) sampling and reconstruction that provide high fidelity signal reconstruction for speech signals; these strategies circumvent the problem of exponentially increasing number of samples as the bit-depth is increased and hence are highly efficient. Specifically, the results indicate that the distribution of the intervals between samples is one of the key factors in the quality of signal reconstruction; including samples with short intervals does not improve the accuracy of the signal reconstruction, whilst samples with large intervals lead to numerical instability. The proposed sampling method, termed reduced conventional level crossing (RCLC) sampling, exploits redundancy between samples to improve the efficiency of the sampling without compromising performance. A reconstruction technique is also proposed that enhances the numerical stability through linear interpolation of samples separated by large intervals. Interpolation is demonstrated to improve the accuracy of the signal reconstruction in addition to the numerical stability. We further demonstrate that the RCLC and interpolation methods can give useful levels of signal recovery even if the average sampling rate is less than the Nyquist rate.
Abstract: Digital Terrain Model (DTM) is a digital numerical representation of the Earth's surface. DTMs have been applied to a diverse field of tasks, such as urban planning, military, glacier mapping, disaster management. In the expression of the Earth' surface as a mathematical model, an infinite number of point measurements are needed. Because of the impossibility of this case, the points at regular intervals are measured to characterize the Earth's surface and DTM of the Earth is generated. Hitherto, the classical measurement techniques and photogrammetry method have widespread use in the construction of DTM. At present, RADAR, LiDAR, and stereo satellite images are also used for the construction of DTM. In recent years, especially because of its superiorities, Airborne Light Detection and Ranging (LiDAR) has an increased use in DTM applications. A 3D point cloud is created with LiDAR technology by obtaining numerous point data. However recently, by the development in image mapping methods, the use of unmanned aerial vehicles (UAV) for photogrammetric data acquisition has increased DTM generation from image-based point cloud. The accuracy of the DTM depends on various factors such as data collection method, the distribution of elevation points, the point density, properties of the surface and interpolation methods. In this study, the random data reduction method is compared for DTMs generated from image based point cloud data. The original image based point cloud data set (100%) is reduced to a series of subsets by using random algorithm, representing the 75, 50, 25 and 5% of the original image based point cloud data set. Over the ANS campus of Afyon Kocatepe University as the test area, DTM constructed from the original image based point cloud data set is compared with DTMs interpolated from reduced data sets by Kriging interpolation method. The results show that the random data reduction method can be used to reduce the image based point cloud datasets to 50% density level while still maintaining the quality of DTM.
Abstract: The global coverage of broadband multimedia and
internet-based services in terrestrial-satellite networks demand
particular interests for satellite providers in order to enhance services
with low latencies and high signal quality to diverse users. In
particular, the delay of on-board processing is an inherent source
of latency in a satellite communication that sometimes is discarded
for the end-to-end delay of the satellite link. The frame work for this
paper includes modelling of an on-orbit satellite payload using an
agent model that can reproduce the properties of processing delays.
In essence, a comparison of different spatial interpolation methods is
carried out to evaluate physical data obtained by an GEO satellite
in order to define a discretization function for determining that
delay. Furthermore, the performance of the proposed agent and the
development of a delay discretization function are together validated
by simulating an hybrid satellite and terrestrial network. Simulation
results show high accuracy according to the characteristics of initial
data points of processing delay for Ku bands.
Abstract: This paper shows in detail the mathematical model of
direct and inverse kinematics for a robot manipulator (welding type)
with four degrees of freedom. Using the D-H parameters, screw
theory, numerical, geometric and interpolation methods, the
theoretical and practical values of the position of robot were
determined using an optimized algorithm for inverse kinematics
obtaining the values of the particular joints in order to determine the
virtual paths in a relatively short time.
Abstract: The morphological short-term evolution of Ponta do Tubarão Island (PTI) was investigated through high accurate surveys based on post-processed kinematic (PPK) relative positioning on Global Navigation Satellite Systems (GNSS). PTI is part of a barrier island system on a high energy northeast Brazilian coastal environment and also an area of high environmental sensitivity. Surveys were carried out quarterly over a two years period from May 2010 to May 2012. This paper assesses statically the performance of digital elevation models (DEM) derived from different interpolation methods to represent morphologic features and to quantify volumetric changes and TIN models shown the best results to that purposes. The MDE allowed quantifying surfaces and volumes in detail as well as identifying the most vulnerable segments of the PTI to erosion and/or accumulation of sediments and relate the alterations to climate conditions. The coastal setting and geometry of PTI protects a significant mangrove ecosystem and some oil and gas facilities installed in the vicinities from damaging effects of strong oceanwaves and currents. Thus, the maintenance of PTI is extremely required but the prediction of its longevity is uncertain because results indicate an irregularity of sedimentary balance and a substantial decline in sediment supply to this coastal area.
Abstract: Computer based geostatistical methods can offer effective data analysis possibilities for agricultural areas by using
vectorial data and their objective informations. These methods will help to detect the spatial changes on different locations of the large
agricultural lands, which will lead to effective fertilization for optimal yield with reduced environmental pollution. In this study, topsoil (0-20 cm) and subsoil (20-40 cm) samples were taken from a
sugar beet field by 20 x 20 m grids. Plant samples were also collected
from the same plots. Some physical and chemical analyses for these
samples were made by routine methods. According to derived variation coefficients, topsoil organic matter (OM) distribution was more than subsoil OM distribution. The highest C.V. value of
17.79% was found for topsoil OM. The data were analyzed
comparatively according to kriging methods which are also used
widely in geostatistic. Several interpolation methods (Ordinary,Simple and Universal) and semivariogram models (Spherical,
Exponential and Gaussian) were tested in order to choose the suitable
methods. Average standard deviations of values estimated by simple
kriging interpolation method were less than average standard
deviations (topsoil OM ± 0.48, N ± 0.37, subsoil OM ± 0.18) of measured values. The most suitable interpolation method was simple
kriging method and exponantial semivariogram model for topsoil,
whereas the best optimal interpolation method was simple kriging
method and spherical semivariogram model for subsoil. The results
also showed that these computer based geostatistical methods should
be tested and calibrated for different experimental conditions and semivariogram models.
Abstract: This paper proposes a dual tree complex wavelet transform (DT-CWT) based directional interpolation scheme for noisy images. The problems of denoising and interpolation are modelled as to estimate the noiseless and missing samples under the same framework of optimal estimation. Initially, DT-CWT is used to decompose an input low-resolution noisy image into low and high frequency subbands. The high-frequency subband images are interpolated by linear minimum mean square estimation (LMMSE) based interpolation, which preserves the edges of the interpolated images. For each noisy LR image sample, we compute multiple estimates of it along different directions and then fuse those directional estimates for a more accurate denoised LR image. The estimation parameters calculated in the denoising processing can be readily used to interpolate the missing samples. The inverse DT-CWT is applied on the denoised input and interpolated high frequency subband images to obtain the high resolution image. Compared with the conventional schemes that perform denoising and interpolation in tandem, the proposed DT-CWT based noisy image interpolation method can reduce many noise-caused interpolation artifacts and preserve well the image edge structures. The visual and quantitative results show that the proposed technique outperforms many of the existing denoising and interpolation methods.
Abstract: Various methods of geofield parameters restoration (by algebraic polynoms; filters; rational fractions; interpolation splines; geostatistical methods – kriging; search methods of nearest points – inverse distance, minimum curvature, local – polynomial interpolation; neural networks) have been analyzed and some possible mistakes arising during geofield surface modeling have been presented.
Abstract: Symbolic Circuit Analysis (SCA) is a technique used
to generate the symbolic expression of a network. It has become a
well-established technique in circuit analysis and design. The
symbolic expression of networks offers excellent way to perform
frequency response analysis, sensitivity computation, stability
measurements, performance optimization, and fault diagnosis. Many
approaches have been proposed in the area of SCA offering different
features and capabilities. Numerical Interpolation methods are very
common in this context, especially by using the Fast Fourier
Transform (FFT). The aim of this paper is to present a method for
SCA that depends on the use of Wavelet Transform (WT) as a
mathematical tool to generate the symbolic expression for large
circuits with minimizing the analysis time by reducing the number of
computations.
Abstract: The new technology of fuzzy neural networks for identification of parameters for mathematical models of geofields is proposed and checked. The effectiveness of that soft computing technology is demonstrated, especially in the early stage of modeling, when the information is uncertain and limited.