Abstract: The fault current levels through the electric devices
have a significant impact on failure probability. New fault current
results in exceeding the rated capacity of circuit breaker and switching
equipments and changes operation characteristic of overcurrent relay.
In order to solve these problems, SFCL (Superconducting Fault
Current Limiter) has rising as one of new alternatives so as to improve
these problems. A fault current reduction differs depending on
installed location. Therefore, a location of SFCL is very important.
Also, SFCL decreases the fault current, and it prevents surrounding
protective devices to be exposed to fault current, it then will bring a
change of reliability. In this paper, we propose method which
determines the optimal location when SFCL is installed in power
system. In addition, the reliability about the power system which
SFCL was installed is evaluated. The efficiency and effectiveness of
this method are also shown by numerical examples and the reliability
indices are evaluated in this study at each load points. These results
show a reliability change of a system when SFCL was installed.
Abstract: Carbon dioxide capture process has been simulated
and studied under different process conditions. It has been shown
that several process parameters such as lean amine temperature,
number of adsorber stages, number of stripper stages and stripper
pressure affect different process conditions and outputs such as
carbon dioxide removal and reboiler duty. It may be concluded that
the simulation of carbon dioxide capture process can help to estimate
the best process conditions.
Abstract: The demand on High voltage (HV) infrastructures is growing due to the corresponding growth in industries and population. New or upgraded HV infrastructure has safety implications since Transmission mains usually occupy the same easement in the vicinity of neighbouring residents. Transmission mains consist of underground (UG) and overhead (OH) sections and the transition between the UG and OH section is known as the UGOH pole. The existence of two transmission mains in the same easement can dictate to resort to more complicated earthing design in order to mitigate the effect of AC interference, and in some cases it can also necessitates completing a Split Study of the system. This paper provides an overview of the AC interference, Split Study and the earthing of an underground feeder including the UGOH pole .In addition, this paper discusses the use of different link boxes on the UG feeder and presents a case study that represent a clear example of the Ac interference and Split factor. Finally, a few recommendations are provided to achieve a safety zone in the area beyond the boundary of the HV system.
Abstract: This paper presents an iterative algorithm to find a
inverse kinematic solution of 5-DOF robot. The algorithm is to
minimize the iteration number. Since the 5-DOF robot cannot give full
orientation of tool. Only z-direction of tool is satisfied while rotation
of tool is determined by kinematic constraint. This work therefore
described how to specify the tool direction and let the tool rotation free.
The simulation results show that this algorithm effectively worked.
Using the proposed iteration algorithm, error due to inverse kinematics
converged to zero rapidly in 5 iterations. This algorithm was applied in
real welding robot and verified through various practical works.
Abstract: Decision Support System (DSS) are interactive
software systems that are built to assist the management of an
organization in the decision making process when faced with nonroutine
problems in a specific application domain. Non-functional
requirements (NFRs) for a DSS deal with the desirable qualities and
restrictions that the DSS functionalities must satisfy. Unlike the
functional requirements, which are tangible functionalities provided
by the DSS, NFRs are often hidden and transparent to DSS users but
affect the quality of the provided functionalities. NFRs are often
overlooked or added later to the system in an ad hoc manner, leading
to a poor overall quality of the system. In this paper, we discuss the
development of NFRs as part of the requirements engineering phase
of the system development life cycle of DSSs. To help eliciting
NFRs, we provide a comprehensive taxonomy of NFRs for DSSs.
Abstract: The focus of this paper is to construct daily time series
exchange rate forecast models of Samoan Tala/USD and Tala/AUD
during the year 2008 to 2012 with neural network The performance
of the models was measured by using varies error functions such as
Root Square mean error (RSME), Mean absolute error (MAE), and
Mean absolute percentage error (MAPE). Our empirical findings
suggest that AR (1) model is an effective tool to forecast the
Tala/USD and Tala/AUD.
Abstract: A DC servomotor position control system using a Fuzzy Logic Sliding mode Model Following Control or FLSMFC approach is presented. The FLSMFC structure consists of an integrator and variable structure system. The integral control is introduced into it in order to eliminated steady state error due to step and ramp command inputs and improve control precision, while the fuzzy control would maintain the insensitivity to parameter variation and disturbances. The FLSMFC strategy is implemented and applied to a position control of a DC servomotor drives. Experimental results indicated that FLSMFC system performance with respect to the sensitivity to parameter variations is greatly reduced. Also, excellent control effects and avoids the chattering phenomenon.
Abstract: The performance of modified Fenton (MF) treatment
to promote PAH oxidation in artificially contaminated soil was
investigated in packed soil column with a hydrogen peroxide (H2O2)
delivery system simulating in situ injection. Soil samples were spiked
with phenanthrene (low molecular weight PAH) and fluoranthene
(high molecular weight PAH) to an initial concentration of 500
mg/kg dried soil each. The effectiveness of process parameters
H2O2/soil, iron/soil, chelating agent/soil weight ratios and reaction
time were studied using a 24 three level factorial design experiments.
Statistically significant quadratic models were developed using
Response Surface Methodology (RSM) for degrading PAHs from the
soil samples. Optimum operating condition was achieved at mild
range of H2O2/soil, iron/soil and chelating agent/soil weight ratios,
indicating cost efficient method for treating highly contaminated
lands.
Abstract: The quality-of-service (QoS) support for wireless
LANs has been a hot research topic during the past few years. In this paper, two QoS provisioning mechanisms are proposed for the employment in 802.11e EDCA MAC scheme. First, the proposed call
admission control mechanism can not only guarantee the QoS for the higher priority existing connections but also provide the minimum reserved bandwidth for traffic flows with lower priority. In addition, the adaptive contention window adjustment mechanism can adjust the
maximum and minimum contention window size dynamically according to the existing connection number of each AC. The collision
probability as well as the packet delay will thus be reduced effectively.
Performance results via simulations have revealed the enhanced QoS property achieved by employing these two mechanisms.
Abstract: Few studies have been conducted on polymeric strip
and the behavior of soil retaining walls. This paper will present the
effect of frequency on the dynamic behavior of reinforced soil
retaining walls with polymeric strips. The frequency content
describes how the amplitude of a ground motion is distributed among
different frequencies. Since the frequency content of an earthquake
motion will strongly influence the effects of that motion, the
characterization of the motion cannot be completed without the
consideration of its frequency content. The maximum axial force of
reinforcements and horizontal displacement of the reinforced walls
are focused in this research. To clarify the dynamic behavior of
reinforced soil retaining walls with polymeric strips, a numerical
modeling using Finite Difference Method is benefited. As the results
indicate, the frequency of input base acceleration has an important
effect on the behavior of these structures. Because of resonant in the
system, where the frequency of the input dynamic load is equal to the
natural frequency of the system, the maximum horizontal
displacement and the maximum axial forces in polymeric strips is
occurred. Moreover, they were to increase the structure flexibility
because of the main advantages of polymeric strips; i.e. being simple
method of construction, having a homogeneous behavior with soils,
and possessing long durability, which are of great importance in
dynamic analysis.
Abstract: To improve the dynamics response of the vehicle
passive suspension, a two-terminal mass is suggested to connect in
parallel with the suspension strut. Three performance criteria, tire grip,
ride comfort and suspension deflection, are taken into consideration to
optimize the suspension parameters. However, the three criteria are
conflicting and non-commensurable. For this reason, the Chebyshev
goal programming method is applied to find the best tradeoff among
the three objectives. A simulation case is presented to describe the
multi-objective optimization procedure. For comparison, the
Chebyshev method is also employed to optimize the design of a
conventional passive suspension. The effectiveness of the proposed
design method has been clearly demonstrated by the result. It is also
shown that the suspension with a two-terminal mass in parallel has
better performance in terms of the three objectives.
Abstract: This paper presents a review of an 8-year study on radiation effects in commercial memory devices operating within the main on-board computer system OBC386 of the Algerian microsatellite Alsat-1. A statistical analysis of single-event upset (SEU) and multiple-bit upset (MBU) activity in these commercial memories shows that the typical SEU rate at alsat-1's orbit is 4.04 × 10-7 SEU/bit/day, where 98.6% of these SEUs cause single-bit errors, 1.22% cause double-byte errors, and the remaining SEUs result in multiple-bit and severe errors.
Abstract: The floating body effect is a serious problem for the
PDSOI MOSFET, and the H-gate layout is frequently used as the body contact to eliminate this effect. Unfortunately, most of the standard commercial SOI MOSFET model is for the device with finger gate, the
necessity of the new models for the H-gate device arises. A simulation
model for the H-gate PDSOI MOSFET is proposed based on the 0.35μm PDSOI process developed by the Institute of Microelectronics
of the Chinese Academy of Sciences (IMECAS), and then the model is well verified by the ring-oscillator.
Abstract: The Ni/α-Al2O3 catalysts with different amounts of La
as promoter from 0 to 4 wt % were prepared, characterized and their
catalytic activity was investigated in syngas methanation reaction.
Effects of reaction temperature and lanthanum loading on carbon
oxides conversion and methane selectivity were also studied. Adding
certain amount of lanthanum to 10Ni /α-Al2O3 catalysts can decrease
the average NiO crystallite diameter which leads to higher activity and
stability while excessive addition would cause deactivation quickly.
Stability on stream towards deactivation was observed up to 800 min
at 500 °C, 0.1MPa and 600000 mL·g-1·h-1.
Abstract: The objective of this study is to evaluate the threshold
stress of the clay with sand subgrade soil. Threshold stress can be
defined as the stress level above which cyclic loading leads to
excessive deformation and eventual failure. The thickness
determination of highways formations using the threshold stress
approach is a more realistic assessment of the soil behaviour because
it is subjected to repeated loadings from moving vehicles. Threshold
stress can be evaluated by plastic strain criterion, which is based on
the accumulated plastic strain behaviour during cyclic loadings [1].
Several conditions of the all-round pressure the subgrade soil namely,
zero confinement, low all-round pressure and high all-round pressure
are investigated. The threshold stresses of various soil conditions are
determined. Threshold stress of the soil are 60%, 31% and 38.6% for
unconfined partially saturated sample, low effective stress saturated
sample, high effective stress saturated sample respectively.
Abstract: Region covariance (RC) descriptor is an effective
and efficient feature for visual tracking. Current RC-based tracking
algorithms use the whole RC matrix to track the target in video
directly. However, there exist some issues for these whole RCbased
algorithms. If some features are contaminated, the whole RC
will become unreliable, which results in lost object-tracking. In
addition, if some features are very discriminative to the
background, other features are still processed and thus reduce the
efficiency. In this paper a new robust tracking method is proposed,
in which the whole RC matrix is decomposed into several low rank
matrices. Those matrices are dynamically chosen and processed so
as to achieve a good tradeoff between discriminability and
complexity. Experimental results have shown that our method is
more robust to complex environment changes, especially either
when occlusion happens or when the background is similar to the
target compared to other RC-based methods.
Abstract: In this paper the effect of faults in the elements and
parts of discrete event systems is investigated. In the occurrence of
faults, some states of the system must be changed and some of them
must be forbidden. For this goal, different states of these elements are
examined and a model for fail-safe behavior of each state is
introduced. Replacing new models of the target elements in the
preliminary model by a systematic method, leads to a fail-safe
discrete event system.
Abstract: Accurate evaluation of damping ratios involving soilstructure interaction (SSI) effects is the prerequisite for seismic design of in-situ buildings. This study proposes a combined approach to identify damping ratios of SSI systems based on ambient excitation technique. The proposed approach is illustrated with main test process, sampling principle and algorithm steps through an engineering example, as along with its feasibility and validity. The proposed approach is employed for damping ratio identification of 82 buildings in Xi-an, China. Based on the experimental data, the variation range and tendency of damping ratios of these SSI systems, along with the preliminary influence factor, are shown and discussed. In addition, a fitting curve indicates the relation between the damping ratio and fundamental natural period of SSI system.
Abstract: Infrared focal plane arrays (IRFPA) sensors, due to
their high sensitivity, high frame frequency and simple structure, have
become the most prominently used detectors in military applications.
However, they suffer from a common problem called the fixed pattern
noise (FPN), which severely degrades image quality and limits the
infrared imaging applications. Therefore, it is necessary to perform
non-uniformity correction (NUC) on IR image. The algorithms of
non-uniformity correction are classified into two main categories, the
calibration-based and scene-based algorithms. There exist some
shortcomings in both algorithms, hence a novel non-uniformity
correction algorithm based on non-linear fit is proposed, which
combines the advantages of the two algorithms. Experimental results
show that the proposed algorithm acquires a good effect of NUC with
a lower non-uniformity ratio.
Abstract: An experiment was conducted under controlled
conditions to study the effect of water extract of leaves, shoots and
roots of either Sisymbrium irio L. =SISIR and/or Descurainia
sophia (L.) Schur =DESSO on the germination and primary growth
of wheat. A split-split plot experiment in CRD with three
replications was used. The main plots were the type of weed: i.e.
SISIR and DESSO and the sub-plots were type of organ: i.e. leaf,
stem and root and, the sub-sub plots were concentration of the
water extract of each organ of the weeds: i.e. 0, 2, 4 and 8 % w/v.
The plant materials were cut in 2-3 cm pieces and then were
ground in a blender. The crushed materials were weighed
according to experimental protocol and the final volume was
reached to 100 ml in distilled water in dark bottles. All bottles were
put on a shaker for 24 hours. The solutions were filtered by muslin
cloth. Whatman paper, 9 cm in diameter, were put in petri dishes
and twenty seeds of wheat were put on it and 5 ml distilled water
or water extract of weeds were added to each petri dish. All petri
dishes were put in constant temperature of 15 0C incubator.
The results showed that the SISIR water extract had a greater
inhibitory effects on germination and primary growth of wheat
than those of DESSO water extract. The water extracts of the
leaves of both weeds had the greatest inhibitory effects on
germination and primary growth of wheat, compared to those of
stems and roots. Increasing the concentration of water extract of
leaves, stems and roots of both weeds up to 8 % caused the greatest
inhibitory effects to wheat and reduced the germination rate and
primary growth of it linearly.