Abstract: Let (U;D) be a Gr-covering approximation space
(U; C) with covering lower approximation operator D and covering
upper approximation operator D. For a subset X of U, this paper
investigates the following three conditions: (1) X is a definable subset
of (U;D); (2) X is an inner definable subset of (U;D); (3) X is an
outer definable subset of (U;D). It is proved that if one of the above
three conditions holds, then the others hold. These results give a
positive answer of an open problem for definable subsets of covering
approximation spaces.
Abstract: The aim of this study was to compare the solubility of selected volatile organic compounds in water and silicon oil using the simple static headspace method. The experimental design allowed equilibrium achievement within 30 – 60 minutes. Infinite dilution activity coefficients and Henry-s law constants for various organics representing esters, ketones, alkanes, aromatics, cycloalkanes and amines were measured at 303K. The measurements were reproducible with a relative standard deviation and coefficient of variation of 1.3x10-3 and 1.3 respectively. The static determined activity coefficients using shaker flasks were reasonably comparable to those obtained using the gas liquid - chromatographic technique and those predicted using the group contribution methods mainly the UNIFAC. Silicon oil chemically known as polydimethysiloxane was found to be better absorbent for VOCs than water which quickly becomes saturated. For example the infinite dilution mole fraction based activity coefficients of hexane is 0.503 and 277 000 in silicon oil and water respectively. Thus silicon oil gives a superior factor of 550 696. Henry-s law constants and activity coefficients at infinite dilution play a significant role in the design of scrubbers for abatement of volatile organic compounds from contaminated air streams. This paper presents the phase equilibrium of volatile organic compounds in very dilute aqueous and polymeric solutions indicating the movement and fate of chemical in air and solvent. The successful comparison of the results obtained here and those obtained using other methods by the same authors and in literature, means that the results obtained here are reliable.
Abstract: Conjugate natural convection in a differentially heated
square enclosure containing a polygon shaped object is studied numerically in this article. The effect of various polygon types on the
fluid flow and thermal performance of the enclosure is addressed for
different thermal conductivities. The governing equations are modeled
and solved numerically using the built-in finite element method of COMSOL software. It is found that the heat transfer rate remains
stable by varying the polygon types.
Abstract: This paper analytically investigates the 3D flow
pattern at the confluences of two rectangular channels having 900
angles using Navier-Stokes equations based on Reynolds Stress
Turbulence Model (RSM). The equations are solved by the Finite-
Volume Method (FVM) and the flow is analyzed in terms of steadystate
(single-phased) conditions. The Shumate experimental findings
were used to test the validity of data. Comparison of the simulation
model with the experimental ones indicated a close proximity
between the flow patterns of the two sets. Effects of the discharge
ratio on separation zone dimensions created in the main-channel
downstream of the confluence indicated an inverse relation, where a
decrease in discharge ratio, will entail an increase in the length and
width of the separation zone. The study also found the model as a
powerful analytical tool in the feasibility study of hydraulic
engineering projects.
Abstract: The highly nonlinear characteristics of drying
processes have prompted researchers to seek new nonlinear control
solutions. However, the relation between the implementation
complexity, on-line processing complexity, reliability control
structure and controller-s performance is not well established. The
present paper proposes high performance nonlinear fuzzy controllers
for a real-time operation of a drying machine, being developed under
a consistent match between those issues. A PCI-6025E data
acquisition device from National Instruments® was used, and the
control system was fully designed with MATLAB® / SIMULINK
language. Drying parameters, namely relative humidity and
temperature, were controlled through MIMOs Hybrid Bang-bang+PI
(BPI) and Four-dimensional Fuzzy Logic (FLC) real-time-based
controllers to perform drying tests on biological materials. The
performance of the drying strategies was compared through several
criteria, which are reported without controllers- retuning. Controllers-
performance analysis has showed much better performance of FLC
than BPI controller. The absolute errors were lower than 8,85 % for
Fuzzy Logic Controller, about three times lower than the
experimental results with BPI control.
Abstract: Wood pyrolysis for Casuarina glauca, Casuarina cunninghamiana, Eucalyptus camaldulensis, Eucalyptus microtheca was made at 450°C with 2.5°C/min. in a flowing N2-atmosphere. The Eucalyptus genus wood gave higher values of specific gravity, ash , total extractives, lignin, N2-liquid trap distillate (NLTD) and water trap distillate (WSP) than those for Casuarina genus. The GHC of NLTD was higher for Casuarina genus than that for Eucalyptus genus with the highest value for Casuarina cunninghamiana. Guiacol, 4-ethyl-2-methoxyphenol and syringol were observed in the NLTD of all the four wood species reflecting their parent hardwood lignin origin. Eucalyptus camaldulensis wood had the highest lignin content (28.89%) and was pyrolyzed to the highest values of phenolics (73.01%), guaiacol (11.2%) and syringol (32.28%) contents in methylene chloride fraction (MCF) of NLTD. Accordingly, recoveries of syringol and guaiacol may become economically attractive from Eucalyptus camaldulensis.
Abstract: Business continuity management (BCM) identifies
potential external and internal threats to an organization and their
impacts to business operations. The goal of the article is to identify,
based on the analysis of employee turnover in organizations in the
Czech Republic, the role of personnel planning in BCM. The article
is organized as follows. The first part of the article concentrates on
the theoretical background of the topic. The second part of the article
is dedicated to the evaluation of the outcomes of the survey
conducted (questionnaire survey), focusing on the analysis of
employee turnover in organizations in the Czech Republic. The final
part of the article underlines the role of personnel planning in BCM,
since poor planning of staff needs in an organization can represent
a future threat for business continuity ensuring.
Abstract: Sub-prime mortgage crisis which began in the US is
regarded as the most economic crisis since the Great Depression in the
early 20th century. Especially, hidden problems on efficient operation
of a business were disclosed at a time and many financial institutions
went bankrupt and filed for court receivership. The collapses of
physical market lead to bankruptcy of manufacturing and construction
businesses. This study is to analyze dynamic efficiency of construction
businesses during the five years at the turn of the global financial
crisis. By discovering the trend and stability of efficiency of a
construction business, this study-s objective is to improve
management efficiency of a construction business in the
ever-changing construction market. Variables were selected by
analyzing corporate information on top 20 construction businesses in
Korea and analyzed for static efficiency in 2008 and dynamic
efficiency between 2006 and 2010. Unlike other studies, this study
succeeded in deducing efficiency trend and stability of a construction
business for five years by using the DEA/Window model. Using the
analysis result, efficient and inefficient companies could be figured
out. In addition, relative efficiency among DMU was measured by
comparing the relationship between input and output variables of
construction businesses. This study can be used as a literature to
improve management efficiency for companies with low efficiency
based on efficiency analysis of construction businesses.
Abstract: Traffic Engineering (TE) is the process of controlling
how traffic flows through a network in order to facilitate efficient and
reliable network operations while simultaneously optimizing network
resource utilization and traffic performance. TE improves the
management of data traffic within a network and provides the better
utilization of network resources. Many research works considers intra
and inter Traffic Engineering separately. But in reality one influences
the other. Hence the effective network performances of both inter and
intra Autonomous Systems (AS) are not optimized properly. To
achieve a better Joint Optimization of both Intra and Inter AS TE, we
propose a joint Optimization technique by considering intra-AS
features during inter – AS TE and vice versa. This work considers the
important criterion say latency within an AS and between ASes. and
proposes a Bi-Criteria Latency optimization model. Hence an overall
network performance can be improved by considering this jointoptimization
technique in terms of Latency.
Abstract: The aim of the present work is to study the effect of annealing on the vibration damping capacity of high-chromium (16%) ferromagnetic steel. The alloys were prepared from raw materials of 99.9% purity melted in a high frequency induction furnace under high vacuum. The samples were heat-treated in vacuum at various temperatures (800 to 1200ºC) for 1 hour followed by slow cooling (120ºC/h). The inverted torsional pendulum method was used to evaluate the vibration damping capacity. The results indicated that the vibration damping capacity of the alloys is influenced by annealing and there exists a critical annealing temperature after 1000ºC. The damping capacity increases quickly below the critical temperature since the magnetic domains move more easily.
Abstract: This paper presents a new true RMS-to-DC converter
circuit based on a square-root-domain squarer/divider. The circuit is
designed by employing up-down translinear loop and using of
MOSFET transistors that operate in strong inversion saturation
region. The converter offer advantages of two-quadrant input current,
low circuit complexity, low supply voltage (1.2V) and immunity
from the body effect. The circuit has been simulated by HSPICE.
The simulation results are seen to conform to the theoretical analysis
and shows benefits of the proposed circuit.
Abstract: The use of hard and brittle material has become
increasingly more extensive in recent years. Therefore processing of
these materials for the parts fabrication has become a challenging
problem. However, it is time-consuming to machine the hard brittle
materials with the traditional metal-cutting technique that uses
abrasive wheels. In addition, the tool would suffer excessive wear as
well. However, if ultrasonic energy is applied to the machining
process and coupled with the use of hard abrasive grits, hard and
brittle materials can be effectively machined. Ultrasonic machining
process is mostly used for the brittle materials. The present research
work has developed models using finite element approach to predict
the mechanical stresses sand strains produced in the tool during
ultrasonic machining process. Also the flow behavior of abrasive
slurry coming out of the nozzle has been studied for simulation using
ANSYS CFX module. The different abrasives of different grit sizes
have been used for the experimentation work.
Abstract: In present study the effects of anti-inflammatory and
antinociceptive of vitex hydro-alcoholic extract were evaluated on
male mice. In inflammatory test mice were divided into 7 groups:
first group was control. The second group, positive control group,
received dexamethasone (15 mg/kg) and the other five groups
received different doses of hydroalcohol extract of Vitex fruit (265,
365, 465, 565, and 665 mg/kg). The inflammation was caused by
xylene-induced ear edema. Formalin test was used for evaluation of
antinociceptive effect of extract. In this test, mice were divided into 7
groups: control, morphine (10mg/kg) as positive control group, and
Vitex extract groups ((265, 365, 465, 565, and 665 mg/kg). All drugs
were administered intrapritoneally, 30 min before each test. The data
were analyzed using one-way ANOVA followed by Tukey-kramer
multiple comparison test. Results have shown significant antiinflammatory
effects of extract at all dosed as compared with control
(P
Abstract: Analysis for the propagation of elastic waves in
arbitrary anisotropic plates is investigated, commencing with a
formal analysis of waves in a layered plate of an arbitrary anisotropic
media, the dispersion relations of elastic waves are obtained by
invoking continuity at the interface and boundary of conditions on
the surfaces of layered plate. The obtained solutions can be used for
material systems of higher symmetry such as monoclinic,
orthotropic, transversely isotropic, cubic, and isotropic as it is
contained implicitly in the analysis. The cases of free layered plate
and layered half space are considered separately. Some special cases
have also been deduced and discussed. Finally numerical solution of
the frequency equations for an aluminum epoxy is carried out, and
the dispersion curves for the few lower modes are presented. The
results obtained theoretically have been verified numerically and
illustrated graphically.
Abstract: The characteristics of fluid flow and phase separation
in an oil-water separator were numerically analysed as part of the
work presented herein. Simulations were performed for different
velocities and droplet diameters, and the way this parameters can
influence the separator geometry was studied.
The simulations were carried out using the software package
Fluent 6.2, which is designed for numerical simulation of fluid flow
and mass transfer. The model consisted of a cylindrical horizontal
separator. A tetrahedral mesh was employed in the computational
domain. The condition of two-phase flow was simulated with the
two-fluid model, taking into consideration turbulence effects using
the k-ε model.
The results showed that there is a strong dependency of phase
separation on mixture velocity and droplet diameter. An increase in
mixture velocity will bring about a slow down in phase separation
and as a consequence will require a weir of greater height. An
increase in droplet diameter will produce a better phase separation.
The simulations are in agreement with results reported in literature
and show that CFD can be a useful tool in studying a horizontal oilwater
separator.
Abstract: Iron oxide nanoparticle was synthesized by reactive-precipitation method followed by high speed centrifuge and phase transfer in order to stabilized nanoparticles in the solvent. Particle size of SPIO was 8.2 nm by SEM, and the hydraulic radius was 17.5 nm by dynamic light scattering method. Coercivity and saturated magnetism were determined by VSM (vibrating sample magnetometer), coercivity of nanoparticle was lower than 10 Hc, and the saturated magnetism was higher than 65 emu/g. Stabilized SPIO was then transferred to aqueous phase by reacted with excess amount of poly (ethylene glycol) (PEG) silane. After filtration and dialysis, the SPIO T2 contrast agent was ready to use. The hydraulic radius of final product was about 70~100 nm, the relaxation rates R2 (1/T2) measured by magnetic resonance imaging (MRI) was larger than 200(sec-1).
Abstract: We have devised a thermal carpet cloak theoretically
and implemented in silicon using layered metamaterial. The layered
metamaterial is composed of single crystalline silicon and its phononic
crystal. The design is based on a coordinate transformation. We
demonstrate the result with numerical simulation. Great cloaking
performance is achieved as a thermal insulator is well hidden under the
thermal carpet cloak. We also show that the thermal carpet cloak can
even the temperature on irregular surface. Using thermal carpet cloak
to manipulate the heat conduction is effective because of its low
complexity.
Abstract: In this paper we describe a computer-aided diagnosis (CAD) system for automated detection of pulmonary nodules in computed-tomography (CT) images. After extracting the pulmonary parenchyma using a combination of image processing techniques, a region growing method is applied to detect nodules based on 3D geometric features. We applied the CAD system to CT scans collected in a screening program for lung cancer detection. Each scan consists of a sequence of about 300 slices stored in DICOM (Digital Imaging and Communications in Medicine) format. All malignant nodules were detected and a low false-positive detection rate was achieved.
Abstract: The biomarker for colorectal cancer (CRC) is CEACAM-6 antigen (C6AG). Therefore, this study aims to develop a novel, simple and low-cost CEACAM-6 antigen immumosensor (C6AG-IMS), based on electrical impedance measurement, for precise determination of C6AG. A low-cost screen-printed graphite electrode was constructed and used as the sensor, with CEACAM-6 antibody (C6AB) immobilized on it. The procedures of sensor fabrication and antibody immobilization are simple and low-cost. Measurement of the electrical impedance at a definite frequency ranges (0.43 – 1.26 MHz) showed that the C6AG-IMS has an excellent linear (r2>0.9) response range (8.125 – 65 pg/mL), covering the normal physiological and pathological ranges of blood C6AG levels. Also, the C6AG-IMS has excellent reliability and validity, with the intraclass correlation coefficient being 0.97. In conclusion, a novel, simple, low-cost and reliable C6AG-IMS was designed and developed, being able to accurately determine blood C6AG levels in the range of pathological and normal physiological regions. The C6AG-IMS can provide a point-of-care and immediate screening results to the user at home.
Abstract: The hydrogen peroxide treatment was able to
remediate chlorophenols, polycyclic aromatic hydrocarbons, diesel
and transformer oil contaminated soil. Chemical treatment of
contaminants adsorbed in peat resulted in lower contaminants-
removal and required higher addition of chemicals than the treatment
of contaminants in sand. The hydrogen peroxide treatment was found
to be feasible for soil remediation at natural soil pH. Contaminants in
soil could degrade with the addition of hydrogen peroxide only
indicating the ability of transition metals ions and minerals of these
metals presented in soil to catalyse the reaction of hydrogen peroxide
decomposition.