Abstract: This paper presents a nonlinear differential model,
for a three-bladed horizontal axis wind turbine (HAWT) suited
for control applications. It is based on a 8-dofs, lumped
parameters structural dynamics coupled with a quasi-steady sectional
aerodynamics. In particular, using the Euler-Lagrange Equation
(Energetic Variation approach), the authors derive, and successively
validate, such model. For the derivation of the aerodynamic model,
the Greenbergs theory, an extension of the theory proposed by
Theodorsen to the case of thin airfoils undergoing pulsating flows,
is used. Specifically, in this work, the authors restricted that theory
under the hypothesis of low perturbation reduced frequency k,
which causes the lift deficiency function C(k) to be real and equal
to 1. Furthermore, the expressions of the aerodynamic loads are
obtained using the quasi-steady strip theory (Hodges and Ormiston),
as a function of the chordwise and normal components of relative
velocity between flow and airfoil Ut, Up, their derivatives, and
section angular velocity ε˙. For the validation of the proposed model,
the authors carried out open and closed-loop simulations of a 5
MW HAWT, characterized by radius R =61.5 m and by mean chord
c = 3 m, with a nominal angular velocity Ωn = 1.266rad/sec.
The first analysis performed is the steady state solution, where
a uniform wind Vw = 11.4 m/s is considered and a collective
pitch angle θ = 0.88◦ is imposed. During this step, the authors
noticed that the proposed model is intrinsically periodic due to
the effect of the wind and of the gravitational force. In order
to reject this periodic trend in the model dynamics, the authors
propose a collective repetitive control algorithm coupled with a PD
controller. In particular, when the reference command to be tracked
and/or the disturbance to be rejected are periodic signals with a
fixed period, the repetitive control strategies can be applied due to
their high precision, simple implementation and little performance
dependency on system parameters. The functional scheme of a
repetitive controller is quite simple and, given a periodic reference
command, is composed of a control block Crc(s) usually added
to an existing feedback control system. The control block contains
and a free time-delay system eτs in a positive feedback loop, and a
low-pass filter q(s). It should be noticed that, while the time delay
term reduces the stability margin, on the other hand the low pass
filter is added to ensure stability. It is worth noting that, in this
work, the authors propose a phase shifting for the controller and
the delay system has been modified as e^(−(T−γk)), where T is the
period of the signal and γk is a phase shifting of k samples of the
same periodic signal. It should be noticed that, the phase shifting
technique is particularly useful in non-minimum phase systems, such
as flexible structures. In fact, using the phase shifting, the iterative
algorithm could reach the convergence also at high frequencies.
Notice that, in our case study, the shifting of k samples depends
both on the rotor angular velocity Ω and on the rotor azimuth
angle Ψ: we refer to this controller as a spatial repetitive controller.
The collective repetitive controller has also been coupled with a C(s) = PD(s), in order to dampen oscillations of the blades.
The performance of the spatial repetitive controller is compared
with an industrial PI controller. In particular, starting from wind
speed velocity Vw = 11.4 m/s the controller is asked to maintain the
nominal angular velocity Ωn = 1.266rad/s after an instantaneous
increase of wind speed (Vw = 15 m/s). Then, a purely periodic
external disturbance is introduced in order to stress the capabilities
of the repetitive controller. The results of the simulations show that,
contrary to a simple PI controller, the spatial repetitive-PD controller
has the capability to reject both external disturbances and periodic
trend in the model dynamics. Finally, the nominal value of the
angular velocity is reached, in accordance with results obtained with
commercial software for a turbine of the same type.
Abstract: This paper investigates the impact on operating time delay and relay maloperation when 1st,2nd and 3rd order analog antialiasing filters are used in numerical distance protection. RC filter with cut-off frequency 90 Hz is used. Simulations are carried out for different SIR (Source to line Impedance Ratio), load, fault type and fault conditions using SIMULINK, where the voltage and current signals are fed online to the developed numerical distance relay model. Matlab is used for plotting the impedance trajectory. Investigation results shows that, about 75 % of the simulated cases, numerical distance relay operating time is not increased even-though there is a time delay when higher order filters are used. Relay maloperation (selectivity) also reduces (increases) when higher order filters are used in numerical distance protection.
Abstract: This work aims to generalize the integer order Sallen-Key filters into the fractional-order domain. The analysis in the case of two different fractional-order elements introduced where the general transfer function becomes four terms which is unusual in the conventional case. In addition, the effect of the transfer function parameters on the filter poles and hence the stability is introduced and closed forms for the filter critical frequencies are driven. Finally, different examples for the fractional order Sallen-Key filter design are presented with circuit simulations using ADS where a great matching between the numerical and simulation results is obtained.
Abstract: This paper proposes a low-voltage and low-power
fully integrated digitally tuned continuous-time channel selection
filter for WiMAX applications. A 5th-order elliptic low-pass filter is
realized in a Gm-C topology. The bandwidth of the fully differential
filter is reconfigurable from 2.5MHz to 20MHz (8x) for different
requirements in WiMAX applications. The filter is simulated in a
standard 90nm CMOS process. Simulation results show the THD
(@Vout =100mVpp) is less than -66dB. The in-band ripple of the
filter is about 0.15dB. The filter consumes 1.5mW from a supply
voltage of 0.9V.
Abstract: A sequential decision problem, based on the task ofidentifying the species of trees given acoustic echo data collectedfrom them, is considered with well-known stochastic classifiers,including single and mixture Gaussian models. Echoes are processedwith a preprocessing stage based on a model of mammalian cochlearfiltering, using a new discrete low-pass filter characteristic. Stoppingtime performance of the sequential decision process is evaluated andcompared. It is observed that the new low pass filter processingresults in faster sequential decisions.
Abstract: The intent of this essay is to evaluate the effectiveness
of surge suppressor aimed at power supply used for automation
devices in power distribution system which is consist of MOV and
T type low-pass filter. Books, journal articles and e-sources related
to surge protection of power supply used for automation devices in
power distribution system were consulted, and the useful information
was organized, analyzed and developed into five parts: characteristics
of surge wave, protection against surge wave, impedance characteristics
of target, using Matlab to simulate circuit response after
5kV,1.2/50s surge wave and suggestions for surge protection. The
results indicate that various types of load situation have great impact
on the effectiveness of surge protective device. Therefore, type and
parameters of surge protective device need to be carefully selected,
and load matching is also vital to be concerned.
Abstract: An active RC filters with a 880 / 1760 MHz dual bandwidth tuning ability is present for 60 GHz unlicensed band applications. A third order Butterworth low-pass filter utilizes two Cherry-Hooper amplifiers to satisfy the very high bandwidth requirements of an amplifier. The low-pass filter is fabricated in 90nm standard CMOS process. Drawing 6.7 mW from 1.2 V power supply, the low frequency gains of the filter are -2.5 and -4.1 dB, and the output third order intercept points (OIP3) are +2.2 and +1.9 dBm for the single channel and channel bonding conditions, respectively.
Abstract: This paper presents a new true RMS-to-DC converter
circuit based on a square-root-domain squarer/divider. The circuit is
designed by employing up-down translinear loop and using of
MOSFET transistors that operate in strong inversion saturation
region. The converter offer advantages of two-quadrant input current,
low circuit complexity, low supply voltage (1.2V) and immunity
from the body effect. The circuit has been simulated by HSPICE.
The simulation results are seen to conform to the theoretical analysis
and shows benefits of the proposed circuit.
Abstract: An improved processing description to be employed in biosonar signal processing in a cochlea model is proposed and examined. It is compared to conventional models using a modified discrimination analysis and both are tested. Their performances are evaluated with echo data captured from natural targets (trees).Results indicate that the phase characteristics of low-pass filters employed in the echo processing have a significant effect on class separability for this data.
Abstract: The empirical mode decomposition (EMD) represents any time series into a finite set of basis functions. The bases are termed as intrinsic mode functions (IMFs) which are mutually orthogonal containing minimum amount of cross-information. The EMD successively extracts the IMFs with the highest local frequencies in a recursive way, which yields effectively a set low-pass filters based entirely on the properties exhibited by the data. In this paper, EMD is applied to explore the properties of the multi-year air temperature and to observe its effects on climate change under global warming. This method decomposes the original time-series into intrinsic time scale. It is capable of analyzing nonlinear, non-stationary climatic time series that cause problems to many linear statistical methods and their users. The analysis results show that the mode of EMD presents seasonal variability. The most of the IMFs have normal distribution and the energy density distribution of the IMFs satisfies Chi-square distribution. The IMFs are more effective in isolating physical processes of various time-scales and also statistically significant. The analysis results also show that the EMD method provides a good job to find many characteristics on inter annual climate. The results suggest that climate fluctuations of every single element such as temperature are the results of variations in the global atmospheric circulation.
Abstract: This article presents a current-mode quadrature
oscillator using differential different current conveyor (DDCC) and
voltage differencing transconductance amplifier (VDTA) as active
elements. The proposed circuit is realized fro m a non-inverting
lossless integrator and an inverting second order low-pass filter. The
oscillation condition and oscillation frequency can be
electronically/orthogonally controlled via input bias currents. The
circuit description is very simple, consisting of merely 1 DDCC, 1
VDTA, 1 grounded resistor and 3 grounded capacitors. Using only
grounded elements, the proposed circuit is then suitable for IC
architecture. The proposed oscillator has high output impedance
which is easy to cascade or dive the external load without the buffer
devices. The PSPICE simulation results are depicted, and the given
results agree well with the theoretical anticipation. The power
consumption is approximately 1.76mW at ±1.25V supply voltages.
Abstract: A high-frequency low-power sinusoidal quadrature
oscillator is presented through the use of two 2nd-order low-pass
current-mirror (CM)-based filters, a 1st-order CM low-pass filter and
a CM bilinear transfer function. The technique is relatively simple
based on (i) inherent time constants of current mirrors, i.e. the
internal capacitances and the transconductance of a diode-connected
NMOS, (ii) a simple negative resistance RN formed by a resistor load
RL of a current mirror. Neither external capacitances nor inductances
are required. As a particular example, a 1.9-GHz, 0.45-mW, 2-V
CMOS low-pass-filter-based all-current-mirror sinusoidal quadrature
oscillator is demonstrated. The oscillation frequency (f0) is 1.9 GHz
and is current-tunable over a range of 370 MHz or 21.6 %. The
power consumption is at approximately 0.45 mW. The amplitude
matching and the quadrature phase matching are better than 0.05 dB
and 0.15°, respectively. Total harmonic distortions (THD) are less
than 0.3 %. At 2 MHz offset from the 1.9 GHz, the carrier to noise
ratio (CNR) is 90.01 dBc/Hz whilst the figure of merit called a
normalized carrier-to-noise ratio (CNRnorm) is 153.03 dBc/Hz. The
ratio of the oscillation frequency (f0) to the unity-gain frequency (fT)
of a transistor is 0.25. Comparisons to other approaches are also
included.