Abstract: This paper presents a SCR-based ESD protection devices for I/O clamp and power rail clamp, respectably. These devices have a low trigger voltage and high holding voltage characteristics than conventional SCR device. These devices are fabricated by using 0.35um BCD (Bipolar-CMOS-DMOS) processes. These devices were validated using a TLP system. From the experimental results, the device for I/O ESD clamp has a trigger voltage of 5.8V. Also, the device for power rail ESD clamp has a holding voltage of 7.7V.
Abstract: This paper presents the IP traffic analysis. The traffic
was collected from the network of Suranaree University of
Technology using the software based on the Simple Network
Management Protocol (SNMP). In particular, we analyze the
distribution of the aggregated traffic during the hours of peak load
and light load. The traffic profiles including the parameters described
the traffic distributions were derived. From the statistical analysis
applying three different methods, including the Kolmogorov Smirnov
test, Anderson Darling test, and Chi-Squared test, we found that the
IP traffic distribution is a non-normal distribution and the
distributions during the peak load and the light load are different. The
experimental study and analysis show high uncertainty of the IP
traffic.
Abstract: This study demonstrates the feasibility of joining the commercial pure copper plates by friction stir welding (FSW). Microstructure, microhardness and tensile properties in terms of the joint efficiency were found 94.03 % compare to as receive base material (BM). The average hardness at the top was higher than bottom. Hardness of weld zone was higher than the base material. Different microstructure zones were revealed by optical microscopy and scanning electron microscopy. The stirred zone (SZ) exhibited primary two phases namely, recrystallized grains and fine precipitates in matrix of copper.
Abstract: Stegnography is a new way of secret
communication the most widely used mechanism on account
of its simplicity is the use of the least significant bit. We have
used the least significant bit (2 LSB and 4 LSB) substitution
method. Depending upon the characteristics of the individual
portions of cover image we decide whether to use 2 LSB or 4
LSB thus it is an adaptive stegnography technique. We used
one of the three channels to behave as indicator to indicate the
presence of hidden data in other two channels. The module
showed impressive results in terms of capacity to hide the
data. In proposed method, instead of using RGB color space
directly, YCbCr color space is used to make use of human
visual system characteristic.
Abstract: The contribution deals with problem of take-off phase of back somersault with twisting with various numbers of twists along longitudinal body axis. The aim was to evaluate the changes in angles during transition phase from back handspring to back somersault using 3D kinematic analysis of the somersaults. We used Simi Motion System for the 3D kinematic analysis of the observed gymnastic element performed by Czech Republic female representative and 2008 Summer Olympic Games participant. The results showed that the higher the number of twists, the smaller the touchdown angle in which the gymnasts lands on the pad in the beginning of take-off phase. In back somersault with one twist (180°) the average angle is 54°, in 1080° back somersault the average angle is 45.9°. These results may help to improve technical training of sports gymnasts.
Abstract: The cuticular hydrocarbons of Pamphagus elephas
(Orthoptera: Pamphagidae) has been analysed by gas
chromatography and by combined gas chromatograph-mass
spectrometry. The following hydrocarbon classes have been
identified in insect cuticular hydrocarbons are: n-alkanes and
methylalkanes comprising Monomethyl-, dimethyl-and
trimethylalkanes. Sexual dimorphism is observed in long chain
alkanes (C24-C36) present on male and female. The cuticulars
hydrocarbons of P.elephas ranged from 24 to 36 carbons and
incluted n-alkanes, Dimethylalkanes and Trimethylalkanes. nalkanes
represented by (C24-C36,72,7% on male and 79,2% on
female), internally branched Monomethylalkanes identified were
(C25, C30-C32,C35-C37;11% on male and 9,4% on female),
Dimethylalkanes detected are (C31-C32, C36; 2,2% on male and
2,06% on female) and Trimethylalkanes detected are (C32, C36;
3,1% on male and 4, 97 on female). Larvae male and female (stage
7) showed the same quality of n-alkanes observed in adults.
However a difference quantity is noted.
Abstract: In geometrical camera calibration, the objective is to
determine a set of camera parameters that describe the mapping
between 3D references coordinates and 2D image coordinates. In this
paper, a technique of calibration and tracking based on both a least
squares method is presented and a correlation technique developed as
part of an augmented reality system. This approach is fast and it can
be used for a real time system
Abstract: Rapid progress in audio compression technology has contributed to the explosive growth of music available in digital form today. In a reversal of ideas, this work makes use of a recently proposed efficient audio compression scheme to develop three important applications in the context of Music Information Retrieval (MIR) for the effective manipulation of large music databases, namely automatic music recommendation (AMR), digital rights management (DRM) and audio finger-printing for song identification. The performance of these three applications has been evaluated with respect to a database of songs collected from a diverse set of genres.
Abstract: One of the factors to maintain system survivability is
the adequate reactive power support to the system. Lack of reactive
power support may cause undesirable voltage decay leading to total
system instability. Thus, appropriate reactive power support scheme
should be arranged in order to maintain system stability. The strength
of a system capacity is normally denoted as system loadability. This
paper presents the enhancement of system loadability through
optimal reactive power planning technique using a newly developed
optimization technique, termed as Multiagent Immune Evolutionary
Programming (MAIEP). The concept of MAIEP is developed based
on the combination of Multiagent System (MAS), Artificial Immune
System (AIS) and Evolutionary Programming (EP). In realizing the
effectiveness of the proposed technique, validation is conducted on
the IEEE-26-Bus Reliability Test System. The results obtained from
pre-optimization and post-optimization process were compared
which eventually revealed the merit of MAIEP.
Abstract: This paper deals with motion planning of multiple
mobile robots. Mobile robots working together to achieve several
objectives have many advantages over single robot system. However,
the planning and coordination between the mobile robots is
extremely difficult. In the present investigation rule-based and rulebased-
neuro-fuzzy techniques are analyzed for multiple mobile
robots navigation in an unknown or partially known environment.
The final aims of the robots are to reach some pre-defined goals.
Based upon a reference motion, direction; distances between the
robots and obstacles; and distances between the robots and targets;
different types of rules are taken heuristically and refined later to find
the steering angle. The control system combines a repelling influence
related to the distance between robots and nearby obstacles and with
an attracting influence between the robots and targets. Then a hybrid
rule-based-neuro-fuzzy technique is analysed to find the steering
angle of the robots. Simulation results show that the proposed rulebased-
neuro-fuzzy technique can improve navigation performance in
complex and unknown environments compared to this simple rulebased
technique.
Abstract: This paper presents an innovative computer system
that contributes to sustainable development of the enterprise. The
research refers to a rethinking of traditional systems of collaboration
and risk assessment, present in any organization, leading to a
sustainable enterprise. This concept integrates emerging tools that
allow the implementation and exploitation of the collective
intelligence of the enterprise, allowing the exchange of contextual,
agile and simplified information, and collaboration with networks of
customers and partners in an environment where risks are controlled.
Risk assessment is done in a systemic way: the enterprise as the
system compared to the contained departments and the enterprise as a
subsystem compared to: families of international standards and
sustainability-s responsibilities. The enterprise, in this systemic
vision, responds to the requirements that any existing system to
operate continuously in an indefinite future without reaching key
resource depletion. The research is done by integrating collaborative
science, engineering, management, psychology, obtaining thus a
cornerstone of sustainable development of the enterprise.
Abstract: The objective of this study was to investigate the effects of dietary supplementation with raw or heat-treated sunflower oil seed with two levels of 7.5% or 15% on unsaturated fatty acids in milk fat and performances of high-yielding lactating cows. Twenty early lactating Holstein cows were used in a complete randomized design. Treatments included: 1) CON, control (without sunflower oil seed). 2) LS-UT, 7.5% raw sunflower oil seed. 3) LS-HT, 7.5% heat-treated sunflower oil seed. 4) HS-UT, 15% raw sunflower oil seed. 5) HS-HT, 15% heat-treated sunflower oil seed. Experimental period lasted for 4 wk, with first 2 wk used for adaptation to the diets. Supplementation with 7.5% raw sunflower seed (LS-UT) tended to decrease milk yield, with 28.37 kg/d compared with the control (34.75 kg/d). Milk fat percentage was increased with the HS-UT treatment that obtained 3.71% compared with CON that was 3.39% and without significant different. Milk protein percent was decreased high level sunflower oil seed treatments (15%) with 3.18% whereas CON treatment is caused 3.40% protein. The cows fed added low sunflower heat-treated (LS-HT) produced milk with the highest content of total unsaturated fatty acid with 32.59 g/100g of milk fat compared with the HS-UT with 23.59 g/100g of milk fat. Content of C18 unsaturated fatty acids in milk fat increased from 21.68 g/100g of fat in the HS-UT to 22.50, 23.98, 27.39 and 30.30 g/100g of fat from the cow fed HS-HT, CON, LS-UT and LS-HT treatments, respectively. C18:2 isomers of fatty acid in milk were greater by LSHT supplementation with significant effect (P < 0.05). Total of C18 unsaturated fatty acids content was significantly higher in milk of animal fed added low heat-treated sunflower (7.5%) than those fed with high sunflower. In all, results of this study showed that diet cow's supplementation with sunflower oil seed tended to reduce milk production of lactating cows but can improve C18 UFA (Unsaturated Fatty Acid) content in milk fat. 7.5% level of sunflower oil seed that heated seemed to be the optimal source to increase UFA production.
Abstract: The paper presents the multi-element synthetic
transmit aperture (MSTA) method with a small number of elements
transmitting and all elements apertures in medical ultrasound
imaging. As compared to the other methods MSTA allows to
increase the system frame rate and provides the best compromise
between penetration depth and lateral resolution.
In the experiments a 128-element linear transducer array with
0.3 mm pitch excited by a burst pulse of 125 ns duration were used.
The comparison of 2D ultrasound images of tissue mimicking
phantom obtained using the STA and the MSTA methods is
presented to demonstrate the benefits of the second approach. The
results were obtained using SA algorithm with transmit and receive
signals correction based on a single element directivity function.
Abstract: Removing noise from the any processed images is very important. Noise should be removed in such a way that important information of image should be preserved. A decisionbased nonlinear algorithm for elimination of band lines, drop lines, mark, band lost and impulses in images is presented in this paper. The algorithm performs two simultaneous operations, namely, detection of corrupted pixels and evaluation of new pixels for replacing the corrupted pixels. Removal of these artifacts is achieved without damaging edges and details. However, the restricted window size renders median operation less effective whenever noise is excessive in that case the proposed algorithm automatically switches to mean filtering. The performance of the algorithm is analyzed in terms of Mean Square Error [MSE], Peak-Signal-to-Noise Ratio [PSNR], Signal-to-Noise Ratio Improved [SNRI], Percentage Of Noise Attenuated [PONA], and Percentage Of Spoiled Pixels [POSP]. This is compared with standard algorithms already in use and improved performance of the proposed algorithm is presented. The advantage of the proposed algorithm is that a single algorithm can replace several independent algorithms which are required for removal of different artifacts.
Abstract: The underground shopping mall has the constructional
problem of the fire evacuation. Also, the people sometimes lose their
direction and information of current time in the mall. If the
emergencies such as terrorist explosions or gas explosions are
happened, they have to go out soon. Under such circumstances, inside
of the mall has high risk for life. In this research, the authors propose a
way that he/she can go out from the underground shopping mall
quickly. If the narrow exits are discovered by using active RFID
(Radio Frequency Identification) tags and using cellular phones, they
can evacuate as soon as possible. To verify this hypothesis, the authors
design the model and carry out the agent-based simulation. They treat,
as a case study, the Tenjin mall in Fukuoka Prefecture in Japan. The
result of the simulation is that the case of the pedestrian with using
active RFID tags and cellular phones reduced the amount of time to
spend on the evacuation. Even if the diffusion of RFID tags and
cellular phones was not perfect, they could show the effectiveness of
reducing the time of evacuation.
Abstract: Quality control in ceramic tile manufacturing is hard, labor intensive and it is performed in a harsh industrial environment with noise, extreme temperature and humidity. It can be divided into color analysis, dimension verification, and surface defect detection, which is the main purpose of our work. Defects detection is still based on the judgment of human operators while most of the other manufacturing activities are automated so, our work is a quality control enhancement by integrating a visual control stage using image processing and morphological operation techniques before the packing operation to improve the homogeneity of batches received by final users.
Abstract: This paper addresses a novel technique for placement of distributed generation (DG) in electric power systems. A GA based approach for sizing and placement of DG keeping in view of system power loss minimization in different loading conditions is explained. Minimal system power loss is obtained under voltage and line loading constraints. Proposed strategy is applied to power distribution systems and its effectiveness is verified through simulation results on 16, 37-bus and 75-bus test systems.
Abstract: In this paper Lattice Boltzmann simulation of
turbulent natural convection with large-eddy simulations (LES) in a
square cavity which is filled by water has been investigated. The
present results are validated by finds of other investigations which
have been done with different numerical methods. Calculations were
performed for high Rayleigh numbers of Ra=108 and 109. The results
confirm that this method is in acceptable agreement with other
verifications of such a flow. In this investigation is tried to present
Large-eddy turbulence flow model by Lattice Boltzmann Method
(LBM) with a clear and simple statement. Effects of increase in
Rayleigh number are displayed on streamlines, isotherm counters and
average Nusselt number. Result shows that the average Nusselt
number enhances with growth of the Rayleigh numbers.
Abstract: Intelligent Transportation System integrates various modern advanced technologies into the ground transportation system, and it will be the goal of urban transport system in the future because of its comprehensive effects. However, it also brings some problems, such as project performance assessment, fairness of benefiting groups, fund management, which are directly related to its operation and implementation. Wuhan has difficulties in organizing transportation because of its nature feature (river and lake), therefore, calling Service of Taxi plays an important role in transportation. This paper researches on calling Service of Taxi in Wuhan, based on quantitative and qualitative analysis. It analyzes its operations management systematically, including business model, finance, usage analysis and users evaluation. As for business model, it is that the government leads the operation at the initial stage, and the third part dominates the operation at the mature stage, which not only eases the pressure of the third part and benefits the spread of the calling service at the initial stage, but also alleviates financial pressure of government and improve the efficiency of the operation at the mature stage. As for finance, it draws that this service will bring heavy financial burden of equipments, but it will be alleviated in the future because of its spread. As for usage analysis, through data comparison, this service can bring some benefits for taxi drivers, and time and spatial distribution of usage have certain features. As for user evaluation, it analyzes using group and the reason why choosing it. At last, according to the analysis above, the paper puts forward the potentials, limitations, and future development strategies for it.
Abstract: The future of business intelligence (BI) is to integrate
intelligence into operational systems that works in real-time
analyzing small chunks of data based on requirements on continuous
basis. This is moving away from traditional approach of doing
analysis on ad-hoc basis or sporadically in passive and off-line mode
analyzing huge amount data. Various AI techniques such as expert
systems, case-based reasoning, neural-networks play important role
in building business intelligent systems. Since BI involves various
tasks and models various types of problems, hybrid intelligent
techniques can be better choice. Intelligent systems accessible
through web services make it easier to integrate them into existing
operational systems to add intelligence in every business processes.
These can be built to be invoked in modular and distributed way to
work in real time. Functionality of such systems can be extended to
get external inputs compatible with formats like RSS. In this paper,
we describe a framework that use effective combinations of these
techniques, accessible through web services and work in real-time.
We have successfully developed various prototype systems and done
few commercial deployments in the area of personalization and
recommendation on mobile and websites.