Abstract: Government reports and published research have
flagged and brought to public attention the deteriorating condition of
a large percentage of bridges in Canada and the United States. With
the increasing number of deteriorated bridges in the US, Canada, and
around the globe, condition assessment techniques of concrete
bridges are evolving. Investigation for bridges’ defects such as
cracks, spalls, and delamination and their level of severity are the
main objectives of condition assessment. Inspection and
rehabilitation programs are being implemented to monitor and
maintain deteriorated bridge infrastructure. This paper highlights the
state-of-the art of current practices being performed for concrete
bridge inspection. The information is gathered from the literature and
through a distributed questionnaire. The current practices in concrete
bridge inspection rely on the use of hummer sounding and chain
dragging tests. Non-Destructive Testing (NDT) techniques are not
being utilized fully in the process. Nonetheless, they are being
partially utilized by the recommendation of the bridge inspector after
conducting visual inspection. Lanes are usually closed during the
performance of visual inspection and bridge inspection in general.
Abstract: This study aims to assess the students' needs for the
tour planning e-guide. The study is developing on the contribution
and importance of the Educational Tour Planning Guide (ETP) is a
multimedia course ware as one of the effective methods in teaching
and learning of environmental science among the students in primary
schools of the Ministry of Education, Malaysia. It is to provide the
student with knowledge and experience about tourism, environmental
science activities and process. E-guide to ETP also hopes to
strengthen the student understanding toward the subject learn in the
tourism environmental science. In order to assess the student's needs
on the e-Guide to Educational Tour Planning in Environmental
Science, the study has produced a similar e-Guide to ETP in the form
as a course ware to be tested during the study. The study has involved
several steps in order to be completed. It is such as the formulation of
the problem, the review of the literature, the formulation of the study
methodology, the production of the e-Guide to ETP, field survey and
finally the analyses and discussion made on the data gathered during
the study. The survey has involved 100 respondents among the
students in standard six primary schools in Kluang Johor. Through
the findings, the study indicates that the current tested product is
acceptable among the students in learning environmental science as a
guide to plan for the tour. The findings also show a slight difference
between the respondents who are using the e-Guide to ETP, and those
who are not on the basis of the e-Guide to ETP results. Due the
important for the study, the researcher hopes to be having a fair
discussion and excellence, recommendation for the development of
the product of the current study. This report is written also important
to provide a written reference for the future related study.
Abstract: The aim of this study is to identify the suitability of
Virtual Learning Environment (VLE) in welding simulator
application towards Computer-Based Training (CBT) in developing
skills upon new students at the Advanced Technology Training
Center (ADTEC) Batu Pahat, Johor, Malaysia and GIATMARA,
Batu Pahat, Johor, Malaysia. The significance of the study is to create
a computer-based skills development approach in welding technology
among new students in ADTEC and GIATMARA as well as to
cultivate the elements of general skills among them. This study is
also important in elevating the number of individual knowledge
workers (K-workers) working in manufacturing industry in order to
achieve a national vision which is to be an industrial nation in the
year of 2020. The design of the study is a survey type of research
which using questionnaires as the instruments and some 136 students
from ADTEC and GIATMARA were interviewed. Descriptive
analysis is used to identify the frequency and mean values. The
findings of the study show that the welding technology has developed
skills in the students because of the application of VLE simulated at a
high level and the respondents agreed that the skills could be
embedded through the application of the VLE simulator. In summary,
the VLE simulator is suitable in welding skills development training
in terms of exposing new students with the relevant characteristics of
welding skills and at the same time spurring the students’ interest
towards learning more about the skills.
Abstract: Nowadays, the reflection on competence management
is the basic for new competitive strategies. It is considered as the core
of the problems of the global supply chain. It interact a variety of
actors: information, physical and activities flows, etc. Even though
competence management is seen as the key factor for any business
success, the existing approaches demonstrate the deficiencies and
limitations of the competence concept. This research has two
objectives: The first is to make a contribution by focusing on the
development of a competence approach, based on continuous
improvement. It allows the enterprise to spot key competencies,
mobilize them in order to serve its strategic objectives and to develop
future competencies. The second is to propose a method to evaluate
the Level of Collective Competence. The approach was confirmed
through an application carried out at an automotive company.
Abstract: Polylactic acid (PLA) is the most commercially
available bio-based and biodegradable plastic at present. PLA has
been used in plastic related industries including single-used
containers, disposable and environmentally friendly packaging owing
to its renewability, compostability, biodegradability, and safety.
Although PLA demonstrates reasonably good optical, physical,
mechanical and barrier properties comparable to the existing
petroleum-based plastics, its brittleness and mold shrinkage as well as
its price are the points to be concerned for the production of rigid and
semi-rigid packaging. Blending PLA with other bio-based polymers
including thermoplastic starch (TPS) is an alternative not only to
achieve a complete bio-based plastic, but also to reduce the
brittleness, shrinkage during molding and production cost of the
PLA-based products. TPS is a material produced mainly from starch
which is cheap, renewable, biodegradable, compostable, and nontoxic.
It is commonly prepared by a plasticization of starch under
applying heat and shear force. Although glycerol has been reported as
one of the most plasticizers used for preparing TPS, its migration
caused the surface stickiness of the TPS products. In some cases,
mixed plasticizers or natural fibers have been applied to impede the
retrogradation of starch or reduce the migration of glycerol. The
introduction of fibers into TPS-based materials could reinforce the
polymer matrix as well. Therefore, the objective of the present
research is to study the effect of starch type (i.e. native starch and
phosphate starch), plasticizer type (i.e. glycerol and xylitol with a
weight ratio of glycerol to xylitol of 100:0, 75:25, 50:50, 25:75 and
0:100) and fiber content (i.e. in the range of 1-25 %wt) on properties
of PLA/TPS blend and composite. PLA/TPS blends and composites
were prepared using a twin-screw extruder and then converted into
dumbbell-shaped specimens using an injection molding machine. The
PLA/TPS blends prepared by using phosphate starch showed higher
tensile strength and stiffness than the blends prepared by using native
one. In contrast, the blends from native starch exhibited higher
extensibility and heat distortion temperature (HDT) than those from
the modified starch. Increasing xylitol content resulted in enhanced
tensile strength, stiffness and water resistance, but decreased
extensibility and HDT of the PLA/TPS blend. Tensile properties and
hydrophobicity of the blend could be improved by incorporating
silane treated-jute fibers.
Abstract: This study, tries to suggest a design method based on
displacement using finite difference numerical modeling in
reinforcing soil retaining wall with steel strip. In this case, dynamic
loading characteristics such as duration, frequency, peak ground
acceleration, geometrical characteristics of reinforced soil structure
and type of the site are considered to correct the pseudo static method
and finally introduce the pseudo static coefficient as a function of
seismic performance level and peak ground acceleration. For this
purpose, the influence of dynamic loading characteristics,
reinforcement length, height of reinforced system and type of the site
are investigated on seismic behavior of reinforcing soil retaining wall
with steel strip. Numerical results illustrate that the seismic response
of this type of wall is highly dependent to cumulative absolute
velocity, maximum acceleration, and height and reinforcement length
so that the reinforcement length can be introduced as the main factor
in shape of failure. Considering the loading parameters, geometric parameters of the
wall and type of the site showed that the used method in this study
leads to efficient designs in comparison with other methods, which
are usually based on limit-equilibrium concept. The outputs show the
over-estimation of equilibrium design methods in comparison with
proposed displacement based methods here.
Abstract: Household waste form a larger proportion of waste
generated across the state, accumulation of organic waste is an
apparent problem and the existing dump sites could be overstress.
Niger state has abundant arable land and water resources thus should
be one of the highest producers of agricultural crops in the country.
However, the major challenge to agricultural sector today is loss of
soil nutrient coupled with high cost of fertilizer. These have
continued to increase the use of fertilizer and decomposed solid waste
for enhance agricultural yield, which have varying effects on the soil
as well a threat to human livelihood. Consequently, vegetable yield
samples from poultry droppings, decomposed household waste
manure, NPK treatments and control from each replication were
subjected to proximate analysis to determine the nutritional and antinutritional
component as well as heavy metal concentration. Data
collected was analyzed using SPSS software and Randomized
complete Block Design means were compared. The result shows that
the treatments do not devoid the concentrations of any nutritional
components while the anti-nutritional analysis proved that NPK had
higher oxalate content than control and organic treats. The
concentration of lead and cadmium are within safe permissible level
while the mercury level exceeded the FAO/WHO maximum
permissible limit for the entire treatments depicts the need for urgent
intervention to minimize mercury levels in soil and manure in order
to mitigate its toxic effect. Thus, eco-agriculture should be widely
accepted and promoted by the stakeholders for soil amendment,
higher yield, strategies for sustainable environmental protection, food
security, poverty eradication, attainment of sustainable development
and healthy livelihood.
Abstract: In IA-MDT, the magnetic implants are placed
strategically at the target site to greatly and locally increase the
magnetic force on MDCPs and help to attract and retain the MDCPs
at the targeted region. In the present work, we develop a
mathematical model to study the capturing of magnetic nanoparticles
flowing within a fluid in an implant assisted cylindrical channel
under magnetic field. A coil of ferromagnetic SS-430 has been
implanted inside the cylindrical channel to enhance the capturing of
magnetic nanoparticles under magnetic field. The dominant magnetic
and drag forces, which significantly affect the capturing of
nanoparticles, are incorporated in the model. It is observed through
model results that capture efficiency increases as we increase the
magnetic field from 0.1 to 0.5 T, respectively. The increase in capture
efficiency by increase in magnetic field is because as the magnetic
field increases, the magnetization force, which is attractive in nature
and responsible to attract or capture the magnetic particles, increases
and results the capturing of large number of magnetic particles due to
high strength of attractive magnetic force.
Abstract: The Greater Athens Area (GAA) faces photochemical
and particulate pollution episodes as a result of the combined effects
of local pollutant emissions, regional pollution transport, synoptic
circulation and topographic characteristics. The area has undergone
significant changes since the Athens 2004 Olympic Games because
of large scale infrastructure works that lead to the shift of population
to areas previously characterized as rural, the increase of the traffic
fleet and the operation of highways. However, few recent modelling
studies have been performed due to the lack of an accurate, updated
emission inventory. The photochemical modelling system
MM5/CAMx was applied in order to study the photochemical and
particulate pollution characteristics above the GAA for two distinct
ten-day periods in the summer of 2006 and 2010, where air pollution
episodes occurred. A new updated emission inventory was used
based on official data. Comparison of modeled results with
measurements revealed the importance and accuracy of the new
Athens emission inventory as compared to previous modeling
studies. The model managed to reproduce the local meteorological
conditions, the daily ozone and particulates fluctuations at different
locations across the GAA. Higher ozone levels were found at
suburban and rural areas as well as over the sea at the south of the
basin. Concerning PM10, high concentrations were computed at the
city centre and the southeastern suburbs in agreement with measured
data. Source apportionment analysis showed that different sources
contribute to the ozone levels, the local sources (traffic, port
activities) affecting its formation.
Abstract: In this paper, we will try to demonstrate the
importance of the project approach in the urban to deal with
uncertainty, the importance of the involvement of all stakeholders in
the urban project process and that the absence of an actor can lead to
project failure but also the importance of the urban project
management. These points are handled through the following questions: Does
the urban adhere to the theory of complexity? Does the project
approach bring hope and solution to make urban planning
"sustainable"? How converging visions of actors for the same
project? Is the management of urban project the solution to support
the urban project approach?
Abstract: This paper integrates Octagon and Square Search
pattern (OCTSS) motion estimation algorithm into H.264/AVC
(Advanced Video Coding) video codec in Adaptive Group of Pictures
(AGOP) mode. AGOP structure is computed based on scene change
in the video sequence. Octagon and square search pattern block-based
motion estimation method is implemented in inter-prediction process
of H.264/AVC. Both these methods reduce bit rate and computational
complexity while maintaining the quality of the video sequence
respectively. Experiments are conducted for different types of video
sequence. The results substantially proved that the bit rate,
computation time and PSNR gain achieved by the proposed method
is better than the existing H.264/AVC with fixed GOP and AGOP.
With a marginal gain in quality of 0.28dB and average gain in bitrate
of 132.87kbps, the proposed method reduces the average computation
time by 27.31 minutes when compared to the existing state-of-art
H.264/AVC video codec.
Abstract: The present study deals with the characterization of
CrSiN coatings obtained by PVD magnetron sputtering systems.
CrSiN films were deposited with different Si contents, in order to
check the effect of at.% variation on the different properties of the
Cr–N system. Coatings were characterized by scanning electron
microscopy (SEM) for thickness measurements, X-ray diffraction.
Surface morphology and the roughness characteristics were explored
using AFM, Mechanicals properties, elastic and plastic deformation
resistance of thin films were investigated using nanoindentation test. We observed that the Si addition improved the hardness and the
Young’s modulus of the Cr–N system. Indeed, the hardness value is
18,56 GPa for CrSiN coatings. Besides, the Young’s modulus value
is 224,22 GPa for CrSiN coatings for Si content of 1.2 at.%.
Abstract: The present study seeks to investigate the application
of expansion strategy in Persian subtitles of English crime movies.
More precisely, this study aims at classifying the different types of
expansion used in subtitles as well as investigating the
appropriateness or inappropriateness of the application of each type.
To achieve this end, three movies; namely, The Net (1995), Contact
(1997) and Mission Impossible 2 (2000), available with Persian
subtitles, were selected for the study. To collect the data, the above
mentioned movies were watched and those parts of the Persian
subtitles in which expansion had been used were identified and
extracted along with their English dialogs. Then, the extracted
Persian subtitles were classified based on the reason that led to
expansion in each case. Next, the appropriateness or
inappropriateness of using expansion in the extracted Persian
subtitles was descriptively investigated. Finally, an equivalent not
containing any expansion was proposed for those cases in which the
meaning could be fully transferred without this strategy. The findings
of the study indicated that the reasons range from explicitation
(explicitation of visual, co-textual and contextual information),
mistranslation and paraphrasing to the preferences of subtitlers.
Furthermore, it was found that the employment of expansion strategy
was inappropriate in all cases except for those caused by explicitation
of contextual information since correct and shorter equivalents which
were equally capable of conveying the intended meaning could be
posited for the original dialogs.
Abstract: The present study examined how translation teachers
develop final tests as measures for checking on the quality of
students’ academic translation in Iranian context. To achieve this
goal, thirty experienced male and female translation teachers from the
four types of the universities offering the program were invited to an
in-depth 30-minute one-session semi-structured interview. The
responses provided showed how much discrepancy exists among the
Iranian translation teachers (as developers of final translation tests),
who are least informed with the current translation evaluation
methods. It was also revealed that the criteria they use for developing
such tests and scoring student translations are not theory-driven but
are highly subjective, mainly based on their personal experience and
intuition. Hence, the quality and accountability of such tests are under
serious question. The results also confirmed that the dominant
method commonly and currently practiced is the purely essay-type
format. To remedy the situation, some suggestions are in order. As
part of the solution, to improve the reliability and validity of such
tests, the present summative, product-oriented evaluation should be
accompanied with some formative, process-oriented methods of
evaluation. Training the teachers and helping them get acquainted
with modern principles of translation evaluation as well as the
existing models, and rating scales does improve the quality of
academic translation evaluation.
Abstract: We consider the problem of stabilization of an unstable
heat equation in a 2-D, 3-D and generally n-D domain by deriving a
generalized backstepping boundary control design methodology. To
stabilize the systems, we design boundary backstepping controllers
inspired by the 1-D unstable heat equation stabilization procedure.
We assume that one side of the boundary is hinged and the other
side is controlled for each direction of the domain. Thus, controllers
act on two boundaries for 2-D domain, three boundaries for 3-D
domain and ”n” boundaries for n-D domain. The main idea of the
design is to derive ”n” controllers for each of the dimensions by
using ”n” kernel functions. Thus, we obtain ”n” controllers for the
”n” dimensional case. We use a transformation to change the system
into an exponentially stable ”n” dimensional heat equation. The
transformation used in this paper is a generalized Volterra/Fredholm
type with ”n” kernel functions for n-D domain instead of the one
kernel function of 1-D design.
Abstract: In the context of the handwriting recognition, we
propose an off line system for the recognition of the Arabic
handwritten words of the Algerian departments. The study is based
mainly on the evaluation of neural network performances, trained
with the gradient back propagation algorithm. The used parameters to
form the input vector of the neural network are extracted on the
binary images of the handwritten word by several methods. The
Distribution parameters, the centered moments of the different
projections of the different segments, the centered moments of the
word image coding according to the directions of Freeman, and the
Barr features applied binary image of the word and on its different
segments. The classification is achieved by a multi layers perceptron.
A detailed experiment is carried and satisfactory recognition results
are reported.
Abstract: In this study, we have collected cases with adipocere
formation, which were from the South Delhi region (average room
temperature 27-390C) and autopsied at our centre. Details of the
circumstances of the death, cause and time of death, surrounding
environment and demographic profile of the deceased were taken into
account. Total 16 cases were included in this study. Adipocere
formation was predominantly present over cheeks, shoulder, breast,
flanks, buttocks, and thighs. Out of 16, 11 cases were found in a dry
atmosphere, 5 cases were brought from the water. There were 5 cases
in which adipocere formation was seen in less than 2 days, and
among them, in 1 case, as early as one day. This study showed that
adipocere formation can be seen as early as 1 day in a hot and humid
environment.
Abstract: This study identified the hypothesised relationship
between creative experience, and revisit intention of handmade
oriental parasol umbrella in Kaohsiung, Taiwan. A face-to-face
questionnaire survey was administered in Meinong town, Kaohsiung.
The components of creative experience were found as “sense of
achievement”, “unique learning” and “interaction with instructors” in
creative tourism. The result also revealed significant positive
relationships between creative experience and revisit intention in
handmade activities. This paper provides additional suggestions for
enhancing revisit intention and guidance regarding creative tourism.
Abstract: The use of information technology in education have
changed not only the learners learning style but also the way they
taught, where nowadays learners are connected with diversity of
information sources with means of knowledge available everywhere.
The advantage of network wireless technologies and mobility
technologies used in the education and learning processes lead to
mobile learning as a new model of learning technology. Currently,
most of mobile learning applications are developed for the formal
education and learning environment. Despite the long history and
large amount of research on mobile learning and instruction design
model still there is a need of well-defined process in designing
mobile learning applications. Based on this situation, this paper
emphasizes on identifying instruction design phase’s considerations
and influencing factors in developing mobile learning application.
This set of instruction design steps includes analysis, design,
development, implementation, evaluation and continuous has been
built from a literature study, with focus on standards for learning,
mobile application software quality and guidelines. The effort is part
of an Omani-funded research project investigating the development,
adoption and dissemination of mobile learning in Oman.
Abstract: In this paper, we present an optimization technique or
a learning algorithm using the hybrid architecture by combining the
most popular sequence recognition models such as Recurrent Neural
Networks (RNNs) and Hidden Markov models (HMMs). In order to
improve the sequence/pattern recognition/classification performance
by applying a hybrid/neural symbolic approach, a gradient descent
learning algorithm is developed using the Real Time Recurrent
Learning of Recurrent Neural Network for processing the knowledge
represented in trained Hidden Markov Models. The developed hybrid
algorithm is implemented on automata theory as a sample test beds
and the performance of the designed algorithm is demonstrated and
evaluated on learning the deterministic finite state automata.