Abstract: Cavities are frequently found beneath conduits on pile
foundations in old embankments. Cavity reduces seepage length
significantly and consequently causes piping failure of embankments.
Case studies of embankment failures indicate that the relative
settlement between ground and pile supported-concrete conduit was
the main reason of the cavity. In this paper, an attempt to simulate the
cavity-induced piping failure mechanism was made using finite
element numerical method. Piping potential is examined by carrying
out parametric study for influencing factors such as cavity length,
water level, and flow conditions. The concentration of hydraulic
gradient adjacent to cavity was found. It is found that the hydraulic
gradient close to the cavity exceeds considerably the critical hydraulic
gradient causing piping. Piping failure potential due to the existence of
cavity is evaluated and contour map for the potential risk of an
embankment for piping failure is proposed.
Abstract: By using an adequate thermal barrier coating in
buildings the energy saving will be happened. In this study, a range
of wall paints with different absorption coefficient in different
climates has been investigated. In order to study these effects, heating
and cooling loads of a common building with different ordinary
paints and paint with mineral coating have been calculated. The
effect of building paint in different climatic condition was studied
and comparison was done between ordinary paints and paint with
mineral insulators in temperate climate to obtain optimized energy
consumption. The results have been shown that coatings with
inorganic micro particles as insulation reduce the energy
consumption of buildings around 14%.
Abstract: Electric field is an important fundamental concept in
electrostatics. In high-school, generally Thai students have already
learned about definition of electric field, electric field due to a point
charge, and superposition of electric fields due to multiple-point
charges. Those are the prerequisite basic knowledge students holding
before entrancing universities. In the first-year university level,
students will be quickly revised those basic knowledge and will be
then introduced to a more complicated topic—electric field due to
continuous charged distributions. We initially found that our
freshman students, who were from the Faculty of Science and
enrolled in the introductory physic course (SCPY 158), often
seriously struggled with the basic physics concepts—superposition of
electric fields and inverse square law and mathematics being relevant
to this topic. These also then resulted on students’ understanding of
advanced topics within the course such as Gauss's law, electric
potential difference, and capacitance. Therefore, it is very important
to determine students' understanding of electric field due to
continuous charged distributions. The open-ended question about
sketching net electric field vectors from a uniformly charged
insulating rod was administered to 260 freshman science students as
pre- and post-tests. All of their responses were analyzed and
classified into five levels of understandings. To get deep
understanding of each level, 30 students were interviewed toward
their individual responses. The pre-test result found was that about
90% of students had incorrect understanding. Even after completing
the lectures, there were only 26.5% of them could provide correct
responses. Up to 50% had confusions and irrelevant ideas. The result
implies that teaching methods in Thai high schools may be
problematic. In addition for our benefit, these students’ alternative
conceptions identified could be used as a guideline for developing the
instructional method currently used in the course especially for
teaching electrostatics.
Abstract: In this paper, an attempt has been made to analyze the effect of wall window orientation on Daylight Illuminance Ratio (DIR) and energy saving in a building known as “SODHA BERS COMPLEX (SBC)” at Varanasi, UP, India. The building has been designed incorporating all passive concepts for thermal comfort as well daylighting concepts to maximize the use of natural daylighting for the occupants in the day to day activities. The annual average DIR and the energy saving has been estimated by using the DIR model for wall window with different orientations under clear sky condition. It has been found that for south oriented window the energy saving per square meter is more compared to the other orientations due to the higher level of solar insolation for the south window in northern hemisphere whereas energy saving potential is minimum for north oriented wall window. The energy saving potential was 26%, 81% and 51% higher for east, south and west oriented window in comparison to north oriented window. The average annual DIR has same trends of variation as the annual energy saving and it is maximum for south oriented window and minimum for north oriented window.
Abstract: The effectiveness of microchannels in enhancing heat
transfer has been demonstrated in the semiconductor industry. In
order to tap the microscale heat transfer effects into macro
geometries, overcoming the cost and technological constraints,
microscale passages were created in macro geometries machined
using conventional fabrication methods. A cylindrical insert was
placed within a pipe, and geometrical profiles were created on the
outer surface of the insert to enhance heat transfer under steady-state
single-phase liquid flow conditions. However, while heat transfer
coefficient values of above 10 kW/m2·K were achieved, the heat
transfer enhancement was accompanied by undesirable pressure drop
increment. Therefore, this study aims to address the high pressure
drop issue using Constructal theory, a universal design law for both
animate and inanimate systems. Two designs based on Constructal theory were developed to study
the effectiveness of Constructal features in reducing the pressure drop
increment as compared to parallel channels, which are commonly
found in microchannel fabrication. The hydrodynamic and heat
transfer performance for the Tree insert and Constructal fin (Cfin)
insert were studied using experimental methods, and the underlying
mechanisms were substantiated by numerical results. In technical
terms, the objective is to achieve at least comparable increment in
both heat transfer coefficient and pressure drop, if not higher
increment in the former parameter. Results show that the Tree insert improved the heat transfer
performance by more than 16 percent at low flow rates, as compared
to the Tree-parallel insert. However, the heat transfer enhancement
reduced to less than 5 percent at high Reynolds numbers. On the
other hand, the pressure drop increment stayed almost constant at 20
percent. This suggests that the Tree insert has better heat transfer
performance in the low Reynolds number region. More importantly,
the Cfin insert displayed improved heat transfer performance along
with favourable hydrodynamic performance, as compared to Cfinparallel
insert, at all flow rates in this study. At 2 L/min, the
enhancement of heat transfer was more than 30 percent, with 20
percent pressure drop increment, as compared to Cfin-parallel insert.
Furthermore, comparable increment in both heat transfer coefficient
and pressure drop was observed at 8 L/min. In other words, the Cfin
insert successfully achieved the objective of this study. Analysis of the results suggests that bifurcation of flows is
effective in reducing the increment in pressure drop relative to heat
transfer enhancement. Optimising the geometries of the Constructal
fins is therefore the potential future study in achieving a bigger stride
in energy efficiency at much lower costs.
Abstract: Flue gas desulfurization gypsum (FGD) is a waste
material arouse from coal power plants. Hydroxyapatite (HAP) is a
biomaterial with porous structure. In this study, FGD gypsum which
retrieved from coal power plant in Turkey was characterized and
HAP particles which can be used as an adsorbent in wastewater
treatment application were synthesized from the FGD gypsum. The
raw materials are characterized by using X Ray Diffraction (XRD)
and Fourier transform infrared spectroscopy (FT-IR) techniques and
produced HAP are characterized by using XRD. As a result, HAP
particles were synthesized at the molar ratio of 5:10, 5:15, 5:20, 5:24,
at room temperature, in alkaline medium (pH=11) and in 1 hour-reaction
time. Among these conditions, 5:20 had the best result.
Abstract: The objective of this research is to mitigate and prevent
the alkali silica reactivity (ASR) in highway construction projects.
ASR is a deleterious reaction initiated when the silica content of the
aggregate reacts with alkali hydroxides in cement in the presence of
relatively high moisture content. The ASR results in the formation of
an expansive white colored gel-like material which forms the
destructive tensile stresses inside hardened concrete. In this research, different types of local aggregates available in the
State of Arkansas were mixed and mortar bars were poured according
to the ASTM specifications. Mortar bars expansion was measured
versus time and aggregates with potential ASR problems were
detected. Different types of supplementary cementitious materials
(SCMs) were used in remixing mortar bars with highly reactive
aggregates. Length changes for remixed bars proved that different
types of SCMs can be successfully used in reducing the expansive
effect of ASR. SCMs percentage by weight is highly dependent on
the SCM type. The result of this study will help avoiding future
losses due to ASR cracking in construction project and reduce the
maintenance, repair, and replacement budgets required for highways
network.
Abstract: Device-to-device (D2D) communication is considered a
promising technique to provide wireless peer-to-peer communication
services. Due to increasing demand on mobile services, available
spectrum for radio frequency (RF) based communications becomes
scarce. Recently, visible light communications (VLC) has evolved
as a high speed wireless data transmission technology for indoor
environments with abundant available bandwidth. In this paper,
a novel VLC based D2D communication that provides wireless
peer-to-peer communication is proposed. Potential low operating
power devices for an efficient D2D communication over increasing
distance of separation between devices is analyzed. Optical repeaters
(OR) are also proposed to enhance the performance in an environment
where direct D2D communications yield degraded performance.
Simulation results show that VLC plays an important role in
providing efficient D2D communication up to a distance of 1 m
between devices. It is also found that the OR significantly improves
the coverage distance up to 3.5 m.
Abstract: The aim of this article is to identify the measures
companies undertake in order to adapt to the environment as well as
discussing their diversity and effectiveness. The research methods
used in the study include an in-depth analysis of the literature and a
case study, which helps to illustrate the issue in question. Referring to
the concept of agility, which is firmly embedded in the theory of
strategic management and has been developed with the aim of
adapting to the environment and its changes, the paper first examines
different types of adaptation measures for companies. Then the issue
under discussion is illustrated with the example of the company
Hortimex. This company is an eminent representative of the world’s
leading manufacturers of food additives and ingredients. The
company was established in 1988 and is a family business, which in
practice means that it conducts business in a responsible manner,
observing the law and respecting the interests of society and the
environment. The company’s mission is to develop a market in
Poland for the products and solutions offered by their partners and to
share their knowledge of additives in food production and
consumption.
Abstract: In this paper, a desiccant solar unit for air
conditioning and desalination is presented first. Secondly, a dynamic
modelling study of the desiccant wheel is developed. After that, a
simulation study and an experimental investigation of the behaviour
of desiccant wheel are developed. The experimental investigation is
done in the chamber of commerce in Freiburg-Germany. Indeed, the
variations of calculated and measured temperatures and specific
humidity of dehumidified and rejected air are presented where a good
agreement is found when comparing the model predictions with
experimental data under the considered range of operating conditions.
Finally, the study of the compartments of desalination and water
condensation shows that the unit can produce an acceptable quantity
of water at the same time of the air conditioning operation.
Abstract: The tribological test with Pin-On-Disc configuration
measures friction and wear properties in dry or lubricated sliding
surfaces of a variety of materials and coatings. Polymeric matrix
composites loaded with mineral filler were used, 1%, 3%, 10%, 30%,
and 50% mass percentage of filler, to reduce the material cost by
using mineral tailings. Using a pin-on-disc tribometer to quantify
coefficient of friction and wear resistance of the specimens. The
parameters known to performing the test were 300 rpm rotation,
normal load of 16N and duration of 33.5 minutes. The composite
with 10% mineral filler performed better, considering that the wear
resistance was good when compared to the other compositions and an
average low coefficient of friction, in the order of μ ≤ 0.15.
Abstract: Effect of Zn addition on the microstructure and
mechanical properties of Mg-Zn alloys with Zn contents from 6 to 10
weight percent was investigated in this study. Through calculation of
phase equilibria of Mg-Zn alloys, carried out by using FactSage® and
FTLite database, solution treatment temperature was decided as
temperatures from 300 to 400oC, where supersaturated solid solution
can be obtained. Solid solution treatment of Mg-Zn alloys was
successfully conducted at 380oC and supersaturated microstructure
with all beta phase resolved into matrix was obtained. After solution
treatment, hot rolling was successfully conducted by reduction of
60%. Compression and tension tests were carried out at room
temperature on the samples as-cast, solution treated, hot-rolled and
recrystallized after rolling. After solid solution treatment, each alloy
was annealed at temperatures of 180 and 200oC for time intervals from
1 min to 48 hrs and hardness of each condition was measured by
micro-Vickers method. Peak aging conditions were deduced as at the
temperature of 200oC for 10 hrs. By addition of Zn by 10 weight
percent, hardness and strength were enhanced.
Abstract: The combination of the properties of graphene oxide
(OG) and PVDF homopolymer makes their combined composite
materials as multifunctional systems with great potential. Knowledge
of the molecular structure is essential for better use. In this work, the
degradation of PVDF polymer exposed to gamma irradiation in
oxygen atmosphere in high dose rate has been studied and compared
to degradation of PVDF/OG composites. The samples were irradiated
with a Co-60 source at constant dose rate, with doses ranging from
100 kGy to 1,000 kGy. In FTIR data shown that the formation of
oxidation products was at the both samples with formation of
carbonyl and hydroxyl groups amongst the most prevalent products
in the pure PVDF samples. In the other hand, the composites samples
exhibit less presence of degradation products with predominant
formation of carbonyl groups, these results also seen in the UV-Vis
analysis. The results show that the samples of composites may have
greater resistance to the irradiation process, since they have less
degradation products than pure PVDF samples seen by spectroscopic
techniques.
Abstract: Autologous Chondrocyte Implantation (ACI) is used worldwide since 1998 to treat cartilage defect. GEL based ACI is a new tissue-engineering technique to treat full thickness cartilage defect with fibrin and thrombin as scaffold for chondrocytes. Purpose of this study is to see safety and efficacy of gel based ACI for knee cartilage defect in multiple centres with different surgeons. Gel-based Autologous Chondrocyte Implantation (GACI) has shown effectiveness in treating isolated cartilage defect of knee joint. Long term results are still needed to be studied. This study was followed-up up to two years and showed benefit to patients. All enrolled patients with a mean age of 28.5 years had an average defect size of3 square centimeters, and were grade IV as per ICRS grading. All patients were followed up several times and at several intervals at 6th week, 8th week, 11th week, 17th week, 29th week, 57th week after surgery. The outcomes were measured based on the IKDC (subjective and objective) and MOCART scores.
Abstract: Elastic scattering of α-particles from 9Be and 11B
nuclei at different alpha energies have been analyzed. Optical model
parameters (OMPs) of α-particles elastic scattering by these nuclei at
different energies have been obtained. In the present calculations, the
real part of the optical potential are derived by folding of nucleonnucleon
(NN) interaction into nuclear matter density distribution of
the projectile and target nuclei using computer code FRESCO. A
density-dependent version of the M3Y interaction (CDM3Y6), which
is based on the G-matrix elements of the Paris NN potential, has been
used. Volumetric integrals of the real and imaginary potential depth
(JR, JW) have been calculated and found to be energy dependent.
Good agreement between the experimental data and the theoretical
predictions in the whole angular range. In double folding (DF)
calculations, the obtained normalization coefficient Nr is in the range
0.70–1.32.
Abstract: Microstructure and fabric of soils play an important
role on structural properties e.g. stiffness and strength of compacted
earthwork. Traditional quality control monitoring based on moisturedensity
tests neither reflects the variability of soil microstructure nor
provides a direct assessment of structural property, which is the
ultimate objective of the earthwork quality control. Since stiffness
and strength are sensitive to soil microstructure and fabric, any
independent test methods that provide simple, rapid, and direct
measurement of stiffness and strength are anticipated to provide an
effective assessment of compacted earthen materials’ uniformity. In
this study, the soil stiffness gauge (SSG) and the dynamic cone
penetrometer (DCP) were respectively utilized to measure and
monitor the stiffness and strength in companion with traditional
moisture-density measurements of various earthen materials used in
Thailand road construction projects. The practical earthwork quality
control criteria are presented herein in order to assure proper
earthwork quality control and uniform structural property of
compacted earthworks.
Abstract: HMS Industrial Networks AB has been recognized as
one of the most innovative companies in the industrial
communication industry worldwide. The creation of their Anybus
innovation during the 1990s contributed considerably to the
company’s success. From inception, HMS’ employees were
innovating for the purpose of creating new business (the creation
phase). After the Anybus innovation, they began the process of
internationalization (the commercialization phase), which in turn led
them to concentrate on cost reduction, product quality, delivery
precision, operational efficiency, and increasing growth (the growth
phase). As a result of this transformation, performing new radical
innovations have become more complicated. The purpose of our research was to explore the dynamics of
innovation at HMS from the aspect of key actors, activities, and
events, over the three phases, in order to understand what led to the
creation of their Anybus innovation, and why it has become
increasingly challenging for HMS to create new radical innovations
for the future. Our research methodology was based on a longitudinal,
retrospective study from the inception of HMS in 1988 to 2014, a
single case study inspired by the grounded theory approach. We
conducted 47 interviews and collected 1 024 historical documents for
our research. Our analysis has revealed that HMS’ success in creating the
Anybus, and developing a successful business around the innovation,
was based on three main capabilities – cultivating customer relations
on different managerial and organizational levels, inspiring business
relations, and balancing complementary human assets for the purpose
of business creation. The success of HMS has turned the management’s attention away
from past activities of key actors, of their behavior, and how they
influenced and stimulated the creation of radical innovations.
Nowadays, they are rhetorically focusing on creativity and
innovation. All the while, their real actions put emphasis on growth,
cost reduction, product quality, delivery precision, operational
efficiency, and moneymaking. In the process of becoming an
international company, HMS gradually refocused. In so doing they
became profitable and successful, but they also forgot what made
them innovative in the first place. Fortunately, HMS’ management
has come to realize that this is the case and they are now in search of
recapturing innovation once again. Our analysis indicates that HMS’ management is facing several
barriers to innovation related path dependency and other lock-in
phenomena. HMS’ management has been captured, trapped in their
mindset and actions, by the success of the past. But now their future has to be secured, and they have come to realize that moneymaking is
not everything. In recent years, HMS’ management have begun to
search for innovation once more, in order to recapture their past
capabilities for creating radical innovations. In order to unlock their
managerial perceptions of customer needs and their counter-innovation
driven activities and events, to utilize the full potential of
their employees and capture the innovation opportunity for the future.
Abstract: The rapid growth of the human population and the
environmental degradation associated with increased consumption of
resources raises concerns on sustainability. Social sustainability
constitutes one of the three dimensions of sustainability together with
environmental and economic dimensions. Even though there is not an
agreement on what social sustainability consists of, it is a well known
fact that it necessitates user participation. The fore, this study aims to
observe and analyze the role of user participation on social
sustainability. In this paper, the links between user participation and indicators of
social sustainability have been searched. In order to achieve this, first
of all a literature review on social sustainability has been done;
accordingly, the information obtained from researches has been used
in the evaluation of the projects conducted in the developing
countries considering user participation. These examples are taken as
role models with pros and cons for the development of the checklist
for the evaluation of the case studies. Furthermore, a case study over
the post earthquake residential settlements in Turkey have been
conducted. The case study projects are selected considering different building
scales (differing number of residential units), scale of the problem
(post-earthquake settlements, rehabilitation of shanty dwellings) and
the variety of users (differing socio-economic dimensions). Decisionmaking,
design, building and usage processes of the selected projects
and actors of these processes have been investigated in the context of
social sustainability. The cases include: New Gourna Village by
Hassan Fathy, Quinta Monroy dwelling units conducted in Chile by
Alejandro Aravena and Beyköy and Beriköy projects in Turkey
aiming to solve the problem of housing which have appeared after the
earthquake happened in 1999 have been investigated. Results of the
study possible links between social sustainability indicators and user
participation and links between user participation and the
peculiarities of place. Results are compared and discussed in order to find possible
solutions to form social sustainability through user participation.
Results show that social sustainability issues depend on communities'
characteristics, socio-economic conditions and user profile but user
participation has positive effects on some social sustainability
indicators like user satisfaction, a sense of belonging and social
stability.
Abstract: The exploitation of flow pulsation in micro- and
mini-channels is a potentially useful technique for enhancing cooling
of high-end photonics and electronics systems. It is thought that
pulsation alters the thickness of the hydrodynamic and thermal
boundary layers, and hence affects the overall thermal resistance
of the heat sink. Although the fluid mechanics and heat transfer
are inextricably linked, it can be useful to decouple the parameters
to better understand the mechanisms underlying any heat transfer
enhancement. Using two-dimensional, two-component particle image
velocimetry, the current work intends to characterize the heat transfer
mechanisms in pulsating flow with a mean Reynolds number of
48 by experimentally quantifying the hydrodynamics of a generic
liquid-cooled channel geometry. Flows circulated through the test
section by a gear pump are modulated using a controller to achieve
sinusoidal flow pulsations with Womersley numbers of 7.45 and
2.36 and an amplitude ratio of 0.75. It is found that the transient
characteristics of the measured velocity profiles are dependent on the
speed of oscillation, in accordance with the analytical solution for
flow in a rectangular channel. A large velocity overshoot is observed
close to the wall at high frequencies, resulting from the interaction
of near-wall viscous stresses and inertial effects of the main fluid
body. The steep velocity gradients at the wall are indicative of
augmented heat transfer, although the local flow reversal may reduce
the upstream temperature difference in heat transfer applications.
While unsteady effects remain evident at the lower frequency, the
annular effect subsides and retreats from the wall. The shear rate at
the wall is increased during the accelerating half-cycle and decreased
during deceleration compared to steady flow, suggesting that the flow
may experience both enhanced and diminished heat transfer during
a single period. Hence, the thickness of the hydrodynamic boundary
layer is reduced for positively moving flow during one half of the
pulsation cycle at the investigated frequencies. It is expected that the
size of the thermal boundary layer is similarly reduced during the
cycle, leading to intervals of heat transfer enhancement.
Abstract: In general, it is desirable to finish the weld quickly,
before a large volume of surrounding metal heats up and expands.
The welding process used, type, welding current and speed of travel,
thus, affect the degree of shrinkage and distortion of a weldment. The
use of mechanized welding equipment reduces welding time, metal
affected zone and consequently distortion. This article helps to define
what weld distortion is and then provide a practical understanding of
the causes of distortion, effects of shrinkage in butt joint welded
assemblies using TI6AL4VA and Aluminium AA2024 alloy sheet.
The beam offset position to the joint interface towards titanium and
aluminium side. The factors affecting distortion during welding is
also given. Test results reveal that welding speed is the significant
parameter to decide the extent of distortion. Also welding from Al
side reduces the distortion while Ti side increases the distortion.