Abstract: This paper presents a numerical investigation of electrically driven flow for enhancing convective heat transfer in a channel flow. This study focuses on the electrode arrangements, number of electrode and electrical voltage on Electrohydrodynamics (EHD) and effect of airflow driven on solid sample surface. The inlet airflow and inlet temperature are 0.35 m/s and 60 oC, respectively. High electrical voltage is tested in the range of 0-30 kV and number of electrode is tested in the range of 1-5. The numerical results show that electric field intensity is depended on electrical voltage and number of electrode. Increasing number of electrodes is increased shear flow, so swirling flow is increased. The swirling flows from aligned and staggered arrangements are affecting within the solid sample. When electrical voltage is increased, temperature distribution and convective heat transfer on the solid sample are significantly increased due to the electric force much stronger.
Abstract: Turbulent forced convection heat transfer and pressure drop characteristics of Al2O3–water nanofluid flowing through a concentric tube heat exchanger with and without coiled wire turbulators were studied experimentally. The experiments were conducted in the Reynolds number ranging from 4000 to 20000, particle volume concentrations of 0.8 vol.% and 1.6 vol.%. Two turbulators with the pitches of 25 mm and 39 mm were used. The results of nanofluids indicated that average Nusselt number increased much more with increasing Reynolds number compared to that of pure water. Thermal conductivity enhancement by the nanofluids resulted in heat transfer enhancement. Once the pressure drop of the alumina/water nanofluid was analyzed, it was nearly equal to that of pure water at the same Reynolds number range. It was concluded that nanofluids with the volume fractions of 0.8 and 1.6 did not have a significant effect on pressure drop change. However, the use of wire coils in heat exchanger enhanced heat transfer as well as the pressure drop.
Abstract: The effectiveness of microchannels in enhancing heat
transfer has been demonstrated in the semiconductor industry. In
order to tap the microscale heat transfer effects into macro
geometries, overcoming the cost and technological constraints,
microscale passages were created in macro geometries machined
using conventional fabrication methods. A cylindrical insert was
placed within a pipe, and geometrical profiles were created on the
outer surface of the insert to enhance heat transfer under steady-state
single-phase liquid flow conditions. However, while heat transfer
coefficient values of above 10 kW/m2·K were achieved, the heat
transfer enhancement was accompanied by undesirable pressure drop
increment. Therefore, this study aims to address the high pressure
drop issue using Constructal theory, a universal design law for both
animate and inanimate systems. Two designs based on Constructal theory were developed to study
the effectiveness of Constructal features in reducing the pressure drop
increment as compared to parallel channels, which are commonly
found in microchannel fabrication. The hydrodynamic and heat
transfer performance for the Tree insert and Constructal fin (Cfin)
insert were studied using experimental methods, and the underlying
mechanisms were substantiated by numerical results. In technical
terms, the objective is to achieve at least comparable increment in
both heat transfer coefficient and pressure drop, if not higher
increment in the former parameter. Results show that the Tree insert improved the heat transfer
performance by more than 16 percent at low flow rates, as compared
to the Tree-parallel insert. However, the heat transfer enhancement
reduced to less than 5 percent at high Reynolds numbers. On the
other hand, the pressure drop increment stayed almost constant at 20
percent. This suggests that the Tree insert has better heat transfer
performance in the low Reynolds number region. More importantly,
the Cfin insert displayed improved heat transfer performance along
with favourable hydrodynamic performance, as compared to Cfinparallel
insert, at all flow rates in this study. At 2 L/min, the
enhancement of heat transfer was more than 30 percent, with 20
percent pressure drop increment, as compared to Cfin-parallel insert.
Furthermore, comparable increment in both heat transfer coefficient
and pressure drop was observed at 8 L/min. In other words, the Cfin
insert successfully achieved the objective of this study. Analysis of the results suggests that bifurcation of flows is
effective in reducing the increment in pressure drop relative to heat
transfer enhancement. Optimising the geometries of the Constructal
fins is therefore the potential future study in achieving a bigger stride
in energy efficiency at much lower costs.