Abstract: Ultrasonic metal welding has been the subject of ongoing research and development, most recently concentrating on metal joining in miniature devices, for example to allow solder-free wire bonding. As well as at the small scale, there are also opportunities to research the joining of thicker sheet metals and to widen the range of similar and dissimilar materials that can be successfully joined using this technology. This study presents the design, characterisation and test of a lateral-drive ultrasonic metal spot welding device. The ultrasonic metal spot welding horn is modelled using finite element analysis (FEA) and its vibration behaviour is characterised experimentally to ensure ultrasonic energy is delivered effectively to the weld coupon. The welding stack and fixtures are then designed and mounted on a test machine to allow a series of experiments to be conducted for various welding and ultrasonic parameters. Weld strength is subsequently analysed using tensile-shear tests. The results show how the weld strength is particularly sensitive to the combination of clamping force and ultrasonic vibration amplitude of the welding tip, but there are optimal combinations of these and also limits that must be clearly identified.
Abstract: Centrifugal-casting machine is used in manufacturing
special machine components like multi-layer journal bearing used in
all internal combustion engine, steam, gas turbine and air craft turboengine
where isotropic properties and high precisions are desired.
Moreover, this machine can be used in manufacturing thin wall hightech
machine components like cylinder liners and piston rings of IC
engine and other machine parts like sleeves, and bushes. Heavy-duty
machine component like railway wheel can also be prepared by
centrifugal casting. A lot of technological developments are required
in casting process for production of good casted machine body and
machine parts. Usually defects like blowholes, surface roughness,
chilled surface etc. are found in sand casted machine parts. But these
can be removed by centrifugal casting machine using rotating
metallic die. Moreover, die rotation, its temperature control, and good
pouring practice can contribute to the quality of casting because of
the fact that the soundness of a casting in large part depends upon
how the metal enters into the mold or dies and solidifies. Poor
pouring practice leads to variety of casting defects such as
temperature loss, low quality casting, excessive turbulence, over
pouring etc. Besides these, handling of molten metal is very
unsecured and dangerous for the workers. In order to get rid of all
these problems, the need of an automatic pouring device arises. In
this research work, a robot assisted pouring device and a centrifugal
casting machine are designed, developed constructed and tested
experimentally which are found to work satisfactorily. The robot
assisted pouring device is further modified and developed for using it
in actual metal casting process. Lot of settings and tests are required
to control the system and ultimately it can be used in automation of
centrifugal casting machine to produce high-tech machine parts with
desired precision.
Abstract: The objective of this research is to develop a general technique so that one may predict the dynamic behaviour of a three-dimensional scale crane model subjected to time-dependent moving point forces by means of conventional finite element computer packages. To this end, the whole scale crane model is divided into two parts: the stationary framework and the moving substructure. In such a case, the dynamic responses of a scale crane model can be predicted from the forced vibration responses of the stationary framework due to actions of the four time-dependent moving point forces induced by the moving substructure. Since the magnitudes and positions of the moving point forces are dependent on the relative positions between the trolley, moving substructure and the stationary framework, it can be found from the numerical results that the time histories for the moving speeds of the moving substructure and the trolley are the key factors affecting the dynamic responses of the scale crane model.
Abstract: In this paper, autonomous performance of a small
manufactured unmanned helicopter is tried to be increased. For this
purpose, a small unmanned helicopter is manufactured in Erciyes
University, Faculty of Aeronautics and Astronautics. It is called as
ZANKA-Heli-I. For performance maximization, autopilot parameters
are determined via minimizing a cost function consisting of flight
performance parameters such as settling time, rise time, overshoot
during trajectory tracking. For this purpose, a stochastic optimization
method named as simultaneous perturbation stochastic approximation
is benefited. Using this approach, considerable autonomous
performance increase (around %23) is obtained.
Abstract: In this paper, it is aimed to improve autonomous flight
performance of a load-carrying (payload: 3 kg and total: 6kg)
unmanned aerial vehicle (UAV) through active wing and horizontal
tail active morphing and also integrated autopilot system parameters
(i.e. P, I, D gains) and UAV parameters (i.e. extension ratios of wing
and horizontal tail during flight) design. For this purpose, a loadcarrying
UAV (i.e. ZANKA-II) is manufactured in Erciyes
University, College of Aviation, Model Aircraft Laboratory is
benefited. Optimum values of UAV parameters and autopilot
parameters are obtained using a stochastic optimization method.
Using this approach autonomous flight performance of UAV is
substantially improved and also in some adverse weather conditions
an opportunity for safe flight is satisfied. Active morphing and
integrated design approach gives confidence, high performance and
easy-utility request of UAV users.
Abstract: A composite material with carbon fiber and polymer
matrix has been used as adherent for manufacturing adhesive joints.
In order to evaluate different fiber orientations on joint performance,
the adherents with the 0°, ±15°, ±30°, ±45° fiber orientations were
used in the single lap joint configuration. The joints with an overlap
length of 25 mm were prepared according to the ASTM 1002
specifications and subjected to tensile loadings. The structural
adhesive used was a two-part epoxy to be cured at 70°C for an hour.
First, mechanical behaviors of the adherents were measured using
three point bending test. In the test, considerations were given to
stress to failure and elastic modulus. The results were compared with
theoretical ones using rule of mixture. Then, the joints were
manufactured in a specially prepared jig, after a proper surface
preparation. Experimental results showed that the fiber orientations
of the adherents affected the joint performance considerably; the
joints with ±45° adherents experienced the worst shear strength, half
of those with 0° adherents, and in general, there was a great
relationship between the fiber orientations and failure mechanisms.
Delamination problems were observed for many joints, which were
thought to be due to peel effects at the ends of the overlap. It was
proved that the surface preparation applied to the adherent surface
was adequate. For further explanation of the results, a numerical
work should be carried out using a possible non-linear analysis.
Abstract: This paper investigates the application of metallic
coatings on high fiber volume fraction carbon/epoxy polymer matrix
composites. For the grip of the metallic layer, a method of modifying
the surface of the composite by introducing a mixture of copper and
steel powder (filler powders) which can reduce the impact of thermal
spray particles. The powder was introduced to the surface at the time
of the forming. Arc spray was used to project the zinc coating layer.
The substrate was grit blasted to avoid poor adherence. The porosity, microstructure, and morphology of layers are
characterized by optical microscopy, SEM and image analysis. The
samples were studied also in terms of hardness and erosion resistance.
This investigation did not reveal any visible evidence damage to the
substrates. The hardness of zinc layer was about 25.94 MPa and the
porosity was around (∼6.70%). The erosion test showed that the zinc
coating improves the resistance to erosion. Based on the results
obtained, we can conclude that thermal spraying allows the production
of protective coating on PMC. Zinc coating has been identified as a
compatible material with the substrate. The filler powders layer
protects the substrate from the impact of hot particles and allows
avoiding the rupture of brittle carbon fibers.
Abstract: The very well-known stacked sets of numbers referred
to as Pascal’s triangle present the coefficients of the binomial
expansion of the form (x+y)n. This paper presents an approach (the
Staircase Horizontal Vertical, SHV-method) to the generalization of
planar Pascal’s triangle for polynomial expansion of the form
(x+y+z+w+r+⋯)n. The presented generalization of Pascal’s triangle
is different from other generalizations of Pascal’s triangles given in
the literature. The coefficients of the generalized Pascal’s triangles,
presented in this work, are generated by inspection, using embedded
Pascal’s triangles. The coefficients of I-variables expansion are
generated by horizontally laying out the Pascal’s elements of (I-1)
variables expansion, in a staircase manner, and multiplying them with
the relevant columns of vertically laid out classical Pascal’s elements,
hence avoiding factorial calculations for generating the coefficients
of the polynomial expansion. Furthermore, the classical Pascal’s
triangle has some pattern built into it regarding its odd and even
numbers. Such pattern is known as the Sierpinski’s triangle. In this
study, a presentation of Sierpinski-like patterns of the generalized
Pascal’s triangles is given. Applications related to those coefficients
of the binomial expansion (Pascal’s triangle), or polynomial
expansion (generalized Pascal’s triangles) can be in areas of
combinatorics, and probabilities.
Abstract: The recent instability in economy was found to be
influencing the situation in Malaysia whether directly or indirectly.
Taking that into consideration, the government needs to find the best
approach to balance its citizen’s socio-economic strata level urgently.
Through education platform is among the efforts planned and acted
upon for the purpose of balancing the effects of the influence,
through the exposure of social entrepreneurial activity towards youth
especially those in higher institution level. Armed with knowledge
and skills that they gained, with the support by entrepreneurial
culture and environment while in campus; indirectly, the students will
lean more on making social entrepreneurship as a career option when
they graduate. Following the issues of marketability and workability
of current graduates that are becoming dire, research involving how
far the willingness of student to create social innovation that
contribute to the society without focusing solely on personal gain is
relevant enough to be conducted. With that, this research is
conducted with the purpose of identifying the level of entrepreneurial
intention and social entrepreneurship among higher institution
students in Malaysia. Stratified random sampling involves 355
undergraduate students from five public universities had been made
as research respondents and data were collected through surveys. The
data was then analyzed descriptively using min score and standard
deviation. The study found that the entrepreneurial intention of higher
education students are on moderate level, however it is the contrary
for social entrepreneurship activities, where it was shown on a high
level. This means that while the students only have moderate level of
willingness to be a social entrepreneur, they are very committed to
created social innovation through the social entrepreneurship
activities conducted. The implication from this study can be
contributed towards the higher institution authorities in prediction the
tendency of student in becoming social entrepreneurs. Thus, the
opportunities and facilities for realizing the courses related to social
entrepreneurship must be created expansively so that the vision of
creating as many social entrepreneurs as possible can be achieved.
Abstract: We present an approach to triangle mesh simplification
designed to be executed on the GPU. We use a quadric error metric
to calculate an error value for each vertex of the mesh and order all
vertices based on this value. This step is followed by the parallel
removal of a number of vertices with the lowest calculated error
values. To allow for the parallel removal of multiple vertices we use
a set of per-vertex boundaries that prevent mesh foldovers even when
simplification operations are performed on neighbouring vertices. We
execute multiple iterations of the calculation of the vertex errors,
ordering of the error values and removal of vertices until either a
desired number of vertices remains in the mesh or a minimum error
value is reached. This parallel approach is used to speed up the
simplification process while maintaining mesh topology and avoiding
foldovers at every step of the simplification.
Abstract: The maintenance of work rolls in hot strip processing
has been lengthy and difficult tasks for hot strip manufacturer
because heavy work rolls have to be taken out of the production line,
which could take hours. One way to increase the time between
maintenance is to improve the effectiveness of the work roll cooling
system such that the wear and tear more slowly occurs, while the
operation cost is kept low. Therefore, this study aims to improve the
work roll cooling system by providing the manufacturer the
relationship between the work-roll temperature reduced by cooling
and the water flow that can help manufacturer determining the more
effective water flow of the cooling system. The relationship is found
using simulation with a systematic process adjustment so that the
satisfying quality of product is achieved. Results suggest that the
manufacturer could reduce the water flow by 9% with roughly the
same performance. With the same process adjustment, the feasibility
of finishing-mill-stand reduction is also investigated. Results suggest
its possibility.
Abstract: Voltage level must be raised in order to deliver the
produced energy to the consumption zones with less loss and less
cost. Power transformers used to raise or lower voltage are important
parts of the energy transmission system. Power transformers used in
switchgear and power generation plants stay in human's intensive
habitat zones as a result of expanding cities. Accordingly, noise
levels produced by power transformers have begun more and more
important and they have established itself as one of the research field.
In this research, the noise cause on transformers has been
investigated, it's causes has been examined and noise measurement
techniques have been introduced. Examples of transformer noise test
results are submitted and precautions to be taken were discussed for
the purpose of decreasing of the noise which will occurred by
transformers.
Abstract: The present paper examines the impact noise
transmission through some floor building assemblies. The Acoubat
software numerical simulation has been used to simulate the impact
noise transmission through different floor configurations used in
Algerian construction mode. The results are compared with the
available measurements. We have developed two experimental
methods, i) field method, and ii) laboratory method using Brüel and
Kjær equipments. The results show that the different cases of floor
configurations need some improvement to ensure the acoustic
comfort in the receiving apartment. The recommended value of the
impact sound level in the receiving room should not exceed 58 dB.
The important results obtained in this paper can be used as platform
to improve the Algerian building acoustic regulation aimed at the
construction of the multi-storey residential building.
Abstract: This paper presents the design and analysis of Liquid Crystal (LC) based tunable reflectarray antenna with slot embedded patch element configurations within X-band frequency range. The slots are shown to modify the surface current distribution on the patch element of reflectarray which causes the resonant patch element to provide different resonant frequencies depending on the slot dimensions. The simulated results are supported and verified by waveguide scattering parameter measurements of different reflectarray unit cells. Different rectangular slots on patch element have been fabricated and a change in resonant frequency from 10.46GHz to 8.78GHz has been demonstrated as the width of the rectangular slot is varied from 0.2W to 0.6W. The rectangular slot in the center of the patch element has also been utilized for the frequency tunable reflectarray antenna design based on K-15 Nematic LC. For the active reflectarray antenna design, a frequency tunability of 1.2% from 10GHz to 9.88GHz has been demonstrated with a dynamic phase range of 103° provided by the measured scattering parameter results. Time consumed by liquid crystals for reconfiguration, which is one of the drawback of LC based design, has also been disused in this paper.
Abstract: Cloud computing can reduce the start-up expenses of implementing EHR (Electronic Health Records). However, many of the healthcare institutions are yet to implement cloud computing due to the associated privacy and security issues. In this paper, we analyze the challenges and opportunities of implementing cloud computing in healthcare. We also analyze data of over 5000 US hospitals that use Telemedicine applications. This analysis helps to understand the importance of smart phones over the desktop systems in different departments of the healthcare institutions. The wide usage of smartphones and cloud computing allows ubiquitous and affordable access to the health data by authorized persons, including patients and doctors. Cloud computing will prove to be beneficial to a majority of the departments in healthcare. Through this analysis, we attempt to understand the different healthcare departments that may benefit significantly from the implementation of cloud computing.
Abstract: This paper describes two methods for the reduction of
the peak input current during the boosting of Dickson charge pumps.
Both methods are implemented in the fully integrated Dickson charge
pumps of a high-voltage display driver chip for smart-card
applications. Experimental results reveal good correspondence with
Spice simulations and show a reduction of the peak input current by a
factor of 6 during boosting.
Abstract: E-Learning enables the users to learn at anywhere at
any time. In E-Learning systems, authenticating the E-Learning user
has security issues. The usage of appropriate communication
networks for providing the internet connectivity for E-learning is
another challenge. WiMAX networks provide Broadband Wireless
Access through the Multicast Broadcast Service so these networks
can be most suitable for E-Learning applications. The authentication
of E-Learning user is vulnerable to session hijacking problems. The
repeated authentication of users can be done to overcome these
issues. In this paper, session based Profile Caching Authentication is
proposed. In this scheme, the credentials of E-Learning users can be
cached at authentication server during the initial authentication
through the appropriate subscriber station. The proposed cache based
authentication scheme performs fast authentication by using cached
user profile. Thus, the proposed authentication protocol reduces the
delay in repeated authentication to enhance the security in ELearning.
Abstract: The UK has had its fair share of the shale gas
revolutionary waves blowing across the global oil and gas industry at
present. Although, its exploitation is widely agreed to have been
delayed, shale gas was looked upon favorably by the UK Parliament
when they recognized it as genuine energy source and granted
licenses to industry to search and extract the resource. This, although
a significant progress by industry, there yet remains another test the
UK fracking resource must pass in order to render shale gas
extraction feasible – it must be economically extractible and
sustainably so. Developing unconventional resources is much more
expensive and risky, and for shale gas wells, producing in
commercial volumes is conditional upon drilling horizontal wells and
hydraulic fracturing, techniques which increase CAPEX. Meanwhile,
investment in shale gas development projects is sensitive to gas price
and technical and geological risks. Using a Two-Factor Model, the
economics of the Bowland shale wells were analyzed and the
operational conditions under which fracking is profitable in the UK
was characterized. We find that there is a great degree of flexibility
about Opex spending; hence Opex does not pose much threat to the
fracking industry in the UK. However, we discover Bowland shale
gas wells fail to add value at gas price of $8/ Mmbtu. A minimum gas
price of $12/Mmbtu at Opex of no more than $2/ Mcf and no more
than $14.95M Capex are required to create value within the present
petroleum tax regime, in the UK fracking industry.
Abstract: Pain management is a question of quality of life and
an indicator for nursing quality. Chronic pain which is predominant
in oncology and palliative nursing situations is perceived today as a
multifactorial, individual emotional experience with specific
characteristics including the sociocultural dimension when dealing
with migrant patients. This dimension of chronic pain is of major
importance in professional nursing of migrant patients in hospices or
palliative care units. Objectives of the study are: 1. To find out more
about the sociocultural views on pain and nursing care, on customs
and nursing practices connected with pain of both Turkish Muslim
and German Christian women, 2. To improve individual and family
oriented nursing practice with view to sociocultural needs of patients
in severe pain in palliative care. In a qualitative-explorative comparative study 4 groups of women,
Turkish Muslims immigrants (4 from the first generation, 5 from the
second generation) and German Christian women of two generations
(5 of each age group) of the same age groups as the Turkish women
and with similar educational backgrounds were interviewed (semistructured
ethnographic interviews using Spradley, 1979) on their
perceptions and experiences of pain and nursing care within their
families. For both target groups the presentation will demonstrate the
following results in detail: Utterance of pain as well as “private” and
“public” pain vary within different societies and cultures. Permitted
forms of pain utterance are learned in childhood and determine
attitudes and expectations in adulthood. Language, especially when
metaphors and symbols are used, plays a major role for
misunderstandings. The sociocultural context of illness may include
specific beliefs that are important to the patients and yet seem more
than far-fetched from a biomedical perspective. Pain can be an
influential factor in family relationships where respect or hierarchies
do not allow the direct utterance of individual needs. Specific
resources are often, although not exclusively, linked to religious
convictions and are significantly helpful in reducing pain. The discussion will evaluate the results of the study with view to
the relevant literature and present nursing interventions and
instruments beyond medication that are helpful when dealing with
patients from various socio-cultural backgrounds in painful end-oflife
situations.
Abstract: The inverted pendulum system is a classic control
problem that is used in universities around the world. It is a suitable
process to test prototype controllers due to its high non-linearities and
lack of stability. The inverted pendulum represents a challenging
control problem, which continually moves toward an uncontrolled
state. This paper presents the possibility of balancing an inverted
pendulum system using sliding mode control (SMC). The goal is to
determine which control strategy delivers better performance with
respect to pendulum’s angle and cart's position. Therefore,
proportional-integral-derivative (PID) is used for comparison. Results
have proven SMC control produced better response compared to PID
control in both normal and noisy systems.