Abstract: In this research the effect of moisture at three levels
(47, 57, and 67 w.b.%) on the physical properties of the Pofaki pea
variety including, dimensions, geometric mean diameter, volume,
sphericity index and the surface area was determined. The influence
of different moisture levels (47, 57 and 67 w.b.%), in two loading
orientation (longitudinal and transverse) and three loading speed (4,6
and 8 mm min-1) on the mechanical properties of pea such as
maximum deformation, rupture force, rupture energy, toughness and
the power to break the pea was investigated. It was observed in the
physical properties that moisture changes were affective at 1% on,
dimensions, geometric mean diameter, volume, sphericity index and
the surface area. It was observed in the mechanical properties that
moisture changes were effective at 1% on, maximum deformation,
rupture force, rupture energy, toughness and the power to break.
Loading speed was effective on maximum deformation, rupture
force, rupture energy at 1% and it was effective on toughness at 5%.
Loading orientation was effective on maximum deformation, rupture
force, rupture energy, toughness at 1% and it was effective on power
at 5%. The mutual effect of speed and orientation were effective on
rupture energy at 1% and were effective on toughness at 5%
probability. The mutual effect of moisture and speed were effective
on rupture force and rupture energy at 1% and were effective on
toughness 5% probability. The mutual effect of orientation and
moisture on rupture energy and toughness were effective at 1%.
Abstract: The paper is focused on the identification of limiting
environmental factors of individual industrial floors on which newly
developed polymer protection and repair systems with the use of
secondary raw materials will be used. These mainly include floors
with extreme stresses and special requirements for materials used. In
relation to the environment of a particular industrial floor, it is
necessary to ensure, for example, chemical stability, resistance to
higher temperatures, resistance to higher mechanical stress, etc. for
developed materials, which is reflected in the demands for the
developed material systems. The paper describes individual
environments and, in relation to them, also requirements for
individual components of the developed materials and for the
developed materials as a whole.
Abstract: This paper deals with the theoretical and numerical
investigation of magneto hydrodynamic boundary layer flow of a
nanofluid past a wedge shaped wick in heat pipe used for the cooling
of electronic components and different type of machines. To
incorporate the effect of nanoparticle diameter, concentration of
nanoparticles in the pure fluid, nanothermal layer formed around the
nanoparticle and Brownian motion of nanoparticles etc., appropriate
models are used for the effective thermal and physical properties of
nanofluids. To model the rotation of nanoparticles inside the base
fluid, microfluidics theory is used. In this investigation ethylene
glycol (EG) based nanofluids, are taken into account. The non-linear
equations governing the flow and heat transfer are solved by using a
very effective particle swarm optimization technique along with
Runge-Kutta method. The values of heat transfer coefficient are
found for different parameters involved in the formulation viz.
nanoparticle concentration, nanoparticle size, magnetic field and
wedge angle etc. It is found that, the wedge angle, presence of
magnetic field, nanoparticle size and nanoparticle concentration etc.
have prominent effects on fluid flow and heat transfer characteristics
for the considered configuration.
Abstract: By textile science incorporating with electronic
industry, developed textile products start to take part in different
areas such as industry, military, space, medical etc. for health,
protection, defense, communication and automation. Electronic
textiles (e-textiles) are fabrics that contain electronics and
interconnections with them. In this study, two types of base yarns
(cotton and acrylic) and three types of conductive steel yarns with
different linear resistance values (14Ω/m, 30Ω/m, 70Ω/m) were used
to investigate the effect of base yarn type and linear resistance of
conductive yarns on thermal behavior of e-textile structures. Thermal
behavior of samples was examined by thermal camera.
Abstract: In emerging economies, recycling is an opportunity
for the cities to increase the lifespan of sanitary landfills, reduce the
costs of the solid waste management, decrease the environmental
problems of the waste treatment through reincorporate waste in the
productive cycle and protect and develop people’s livelihoods of
informal waste pickers. However, few studies have analysed the
possibilities and strategies to integrate formal and informal sectors in
the solid waste management for the benefit of both. This study seek
to make a strength, weakness, opportunity, and threat (SWOT)
analysis in three recycling associations of Bogotá with the aim to
understand and determine the situation of recycling from perspective
of informal sector in its transition to enter as authorized waste
providers. Data used in the analysis are derived from multiple
strategies such as literature review, the Bogota’s recycling database,
focus group meetings, governmental reports, national laws and
regulations and specific interviews with key stakeholders. Results of
this study show as the main stakeholders of formal and informal
sector of waste management can identify the internal and internal
conditions of recycling in Bogotá. Several strategies were designed
based on the SWOTs determined, could be useful for Bogotá to
advance and promote recycling as a key strategy for integrated
sustainable waste management in the city.
Abstract: We investigate relaxation dynamics of a quantum
dipole emitter (QDE), e.g., a molecule or quantum dot, located near a
metal nanoparticle (MNP) exhibiting a dipolar localized surface
plasmon (LSP) resonance at the frequency of the QDE radiative
transition. It is shown that under the condition of the QDE-MNP
characteristic relaxation time being much shorter than that of the
QDE in free-space but much longer than the LSP lifetime. It is also
shown that energy dissipation in the QDE-MNP system is relatively
weak with the probability of the photon emission being about 0.75, a
number which, rather surprisingly, does not explicitly depend on the
metal absorption characteristics. The degree of entanglement
measured by the concurrency takes the maximum value, while the
distances between the QDEs and metal ball approximately are equal.
Abstract: Propylene self-metathesis to ethylene and butene was
studied over WOx/SiO2 catalysts at 450oC and atmospheric pressure.
The WOx/SiO2 catalysts were prepared by incipient wetness
impregnation of ammonium metatungstate aqueous solution. It was
found that, adding nano-sized extra supports (SiO2 and TiO2) by
physical mixing with the WOx/SiO2 enhanced propylene conversion.
The UV-Vis and FT-Raman results revealed that WOx could migrate
from the original silica support to the extra support, leading to a
better dispersion of WOx. The ICP-OES results also indicate that
WOx existed on the extra support. Coke formation was investigated
on the catalysts after 10 h time-on-stream by TPO. However, adding
nano-sized extra supports led to higher coke formation which may be
related to acidity as characterized by NH3-TPD.
Abstract: A cyclostationary Gaussian linearization method is
formulated for investigating the time average response of nonlinear
system under sinusoidal signal and white noise excitation. The
quantitative measure of cyclostationary mean, variance, spectrum of
mean amplitude, and mean power spectral density of noise are
analyzed. The qualitative response behavior of stochastic jump and
bifurcation are investigated. The validity of the present approach in
predicting the quantitative and qualitative statistical responses is
supported by utilizing Monte Carlo simulations. The present analysis
without imposing restrictive analytical conditions can be directly
derived by solving non-linear algebraic equations. The analytical
solution gives reliable quantitative and qualitative prediction of mean
and noise response for the Duffing system subjected to both sinusoidal
signal and white noise excitation.
Abstract: The capability of exploiting the electronic charge and
spin properties simultaneously in a single material has made diluted
magnetic semiconductors (DMS) remarkable in the field of
spintronics. We report the designing of DMS based on zinc-blend
ZnO doped with Cr impurity. The full potential linearized augmented
plane wave plus local orbital FP-L(APW+lo) method in density
functional theory (DFT) has been adapted to carry out these
investigations. For treatment of exchange and correlation energy,
generalized gradient approximations have been used. Introducing Cr
atoms in the matrix of ZnO has induced strong magnetic moment
with ferromagnetic ordering at stable ground state. Cr:ZnO was found
to favor the short range magnetic interaction that
reflect tendency of Cr clustering. The electronic structure of ZnO is
strongly influenced in the presence of Cr impurity atoms where
impurity bands appear in the band gap.
Abstract: Although, lanthanum carbonate has not been approved
by the FDA for treatment of hyperphosphatemia, we prospectively
evaluated the efficacy of the combination of Calcium hydroxyapatite
(CHAp) and Lanthanum Carbonate (LaC) for the treatment of
hyperphosphatemia on mice. CHAp was prepared by co-precipitation
method using Ca(OH)2, H3PO4, NH4OH with calcination at 1200ºC.
Lanthanum carbonate was prepared by chemical method using
NaHCO3 and LaCl3 at low pH environment, below 4.0. The
structures were characterized by FTIR spectra and SEM -EDX
analysis. The study group included 16 subjects-mice divided into four
groups according to the administered substance: lanthanum carbonate
(group A), CHAp (group B), lanthanum carbonate + CHAp (group C)
and salt water (group D). The results indicate a phosphate decrease
when subjects (mice) were treated with CHAp and lanthanum
carbonate (0.5% CMC), in a single dose of 1500 mg/kg. Serum
phosphate concentration decreased [(from 4.5 ± 0.8 mg/dL) to
4.05 ± 0.2 mg/dL), P < 0.01] in group A and in group C (to 3.6
± 0.2 mg/dL) at 12 hours from the administration. The combination
of CHAp and lanthanum carbonate is a suitable regimen for
hyperphosphatemia treatment because it avoids both the
hypercalcemia of CaCO3 and the adverse effects of CHAp.
Abstract: This study investigates the suitability of using plastic,
such as polyethylene terephthalate (PET), as a partial replacement of
natural coarse and fine aggregates (for example, brick chips and
natural sand) to produce lightweight concrete for load bearing
structural members. The plastic coarse aggregate (PCA) and plastic
fine aggregate (PFA) were produced from melted polyethylene
terephthalate (PET) bottles. Tests were conducted using three
different water–cement (w/c) ratios, such as 0.42, 0.48, and 0.57,
where PCA and PFA were used as 50% replacement of coarse and
fine aggregate respectively. Fresh and hardened properties of
concrete have been compared for natural aggregate concrete (NAC),
PCA concrete (PCC) and PFA concrete (PFC). The compressive
strength of concrete at 28 days varied with the water–cement ratio for
both the PCC and PFC. Between PCC and PFC, PFA concrete
showed the highest compressive strength (23.7 MPa) at 0.42 w/c ratio
and also the lowest compressive strength (13.7 MPa) at 0.57 w/c
ratio. Significant reduction in concrete density was mostly observed
for PCC samples, ranging between 1977–1924 kg/m³. With the
increase in water–cement ratio PCC achieved higher workability
compare to both NAC and PFC. It was found that both the PCA and
PFA contained concrete achieved the required compressive strength
to be used for structural purpose as partial replacement of the natural
aggregate; but to obtain the desired lower density as lightweight
concrete the PCA is most suited.
Abstract: The quality and condition of perishable products
delivered to the market and their subsequent selling prices are
directly affected by the care taken during harvesting and handling.
Mechanical injury, in fact, occurs at all stages, from pre-harvest
operations through post-harvest handling, packing and transport to
the market. The main implications of this damage are the reduction of
the product’s quality and economical losses related to the shelf life
diminution. For most perishable products, the shelf life is relatively
short and it is typically dictated by microbial growth related to the
application of dynamic and static loads during transportation. This
paper presents the correlation between vibration levels and
microbiological growth on strawberries and woodland strawberries
and detects the presence of volatile organic compounds (VOC) in
order to develop an intelligent logistic unit capable of monitoring
VOCs using a specific sensor system. Fresh fruits were exposed to
vibrations by means of a vibrating table in a temperature-controlled
environment. Microbiological analyses were conducted on samples,
taken at different positions along the column of the crates. The values
obtained were compared with control samples not exposed to
vibrations and the results show that different positions along the
column influence the development of bacteria, yeasts and filamentous
fungi.
Abstract: Alone with fast urbanization in world, traffic control
became a big issue in urban construction. Having an efficient and
reliable traffic control system is crucial to macro-traffic control.
Traffic signal is used to manage conflicting requirement by allocating
different sets of mutually compatible traffic movement during distinct
time interval. Many approaches have been made proposed to solve
this discrete stochastic problem. Recognizing the need to minimize
right-of-way impacts while efficiently handling the anticipated high
traffic volumes, the proposed alternative system gives effective
design. This model allows for increased traffic capacity and reduces
delays by eliminating a step in maneuvering through the freeway
interchange. The concept proposed in this paper involves
construction of bridges and ramps at intersection of four roads to
control the vehicular congestion and to prevent traffic breakdown.
Abstract: Subspace channel estimation methods have been
studied widely, where the subspace of the covariance matrix is
decomposed to separate the signal subspace from noise subspace. The
decomposition is normally done by using either the eigenvalue
decomposition (EVD) or the singular value decomposition (SVD) of
the auto-correlation matrix (ACM). However, the subspace
decomposition process is computationally expensive. This paper
considers the estimation of the multipath slow frequency hopping
(FH) channel using noise space based method. In particular, an
efficient method is proposed to estimate the multipath time delays by
applying multiple signal classification (MUSIC) algorithm which is
based on the null space extracted by the rank revealing LU (RRLU)
factorization. As a result, precise information is provided by the
RRLU about the numerical null space and the rank, (i.e., important
tool in linear algebra). The simulation results demonstrate the
effectiveness of the proposed novel method by approximately
decreasing the computational complexity to the half as compared
with RRQR methods keeping the same performance.
Abstract: Exact solution of an unsteady MHD flow of elasticoviscous
fluid through a porous media in a tube of spherical cross
section under the influence of magnetic field and constant pressure
gradient has been obtained in this paper. Initially, the flow is
generated by a constant pressure gradient. After attaining the steady
state, the pressure gradient is suddenly withdrawn and the resulting
fluid motion in a tube of spherical cross section by taking into
account of the porosity factor and magnetic parameter of the
bounding surface is investigated. The problem is solved in two-stages
the first stage is a steady motion in tube under the influence of a
constant pressure gradient, the second stage concern with an unsteady
motion. The problem is solved employing separation of variables
technique. The results are expressed in terms of a non-dimensional
porosity parameter (K), magnetic parameter (m) and elasticoviscosity
parameter (β), which depends on the Non-Newtonian
coefficient. The flow parameters are found to be identical with that of
Newtonian case as elastic-viscosity parameter and magnetic
parameter tends to zero and porosity tends to infinity. It is seen that
the effect of elastico-viscosity parameter, porosity parameter and
magnetic parameter of the bounding surface has significant effect on
the velocity parameter.
Abstract: The material selection in the design of the sandwich
structures is very crucial aspect because of the positive or negative
influences of the base materials to the mechanical properties of the
entire panel. In the literature, it was presented that the selection of the
skin and core materials plays very important role on the behavior of
the sandwich. Beside this, the use of the correct adhesive can make
the whole structure to show better mechanical results and behavior.
In the present work, the static three-point bending tests were
performed on the sandwiches having an aluminum alloy foam core,
the skins made of three different types of fabrics and two different
commercial adhesives (flexible polyurethane and toughened epoxy
based) at different values of support span distances by aiming the
analyses of their flexural performance in terms of absorbed energy,
peak force values and collapse mechanisms. The main results of the
flexural loading are: force-displacement curves obtained after the
bending tests, peak force and absorbed energy values, collapse
mechanisms and adhesion quality. The experimental results presented
that the sandwiches with epoxy based toughened adhesive and the
skins made of S-Glass Woven fabrics indicated the best adhesion
quality and mechanical properties. The sandwiches with toughened
adhesive exhibited higher peak force and energy absorption values
compared to the sandwiches with flexible adhesive. The use of these
sandwich structures can lead to a weight reduction of the transport
vehicles, providing an adequate structural strength under operating
conditions.
Abstract: Optical radiation emitted from a metal-coated fiber tip apex at liquid-air interface was measured. The intensity of the output radiation was strongly depend on the relative position of the tip to a liquid-air interface and varied with surface fluctuations. This phenomenon permits in-situ real-time investigation of nano-metric vibrations of the liquid surface and provides a basis for development of various origin ultrasensitive vibration detecting sensors. The described method can be used for detection of week seismic vibrations.
Abstract: Taiwan is a hyper endemic area for the Hepatitis B
virus (HBV). The estimated total number of HBsAg carriers in the
general population who are more than 20 years old is more than 3
million. Therefore, a case record review is conducted from January
2003 to June 2007 for all patients with a diagnosis of acute hepatitis
who were admitted to the Emergency Department (ED) of a
well-known teaching hospital. The cost for the use of medical
resources is defined as the total medical fee. In this study, principal
component analysis (PCA) is firstly employed to reduce the number of
dimensions. Support vector regression (SVR) and artificial neural
network (ANN) are then used to develop the forecasting model. A total
of 117 patients meet the inclusion criteria. 61% patients involved in
this study are hepatitis B related. The computational result shows that
the proposed PCA-SVR model has superior performance than other
compared algorithms. In conclusion, the Child-Pugh score and
echogram can both be used to predict the cost of medical resources for
patients with acute hepatitis in the ED.
Abstract: This study examined how individuals in their
respective teams contributed to innovation performance besides
defining the term of innovation in their own respective views. This
study also identified factors that motivated University staff to
contribute to the innovation products. In addition, it examined
whether there is a significant relationship between professional
training level and the length of service among university staff
towards innovation and to what extent do the two variables
contributed towards innovative products. The significance of this
study is that it revealed the strengths and weaknesses of the
university staff when contributing to innovation performance.
Stratified-random sampling was employed to determine the samples
representing the population of lecturers in the study, involving 123
lecturers in one of the local universities in Malaysia. The method
employed to analyze the data is through categorizing into themes for
the open-ended questions besides using descriptive and inferential
statistics for the quantitative data. This study revealed that two types
of definition for the term “innovation” exist among the university
staff, namely, creation of new product or new approach to do things
as well as value-added creative way to upgrade or improve existing
process and service to be more efficient. This study found that the
most prominent factor that propels them towards innovation is to
improve the product in order to benefit users, followed by selfsatisfaction
and recognition. This implies that the staff in the
organization viewed the creation of innovative products as a process
of growth to fulfill the needs of others and also to realize their
personal potential. This study also found that there was only a
significant relationship between the professional training level and
the length of service of 4 - 6 years among the university staff. The
rest of the groups based on the length of service showed that there
was no significant relationship with the professional training level
towards innovation. Moreover, results of the study on directional
measures depicted that the relationship for the length of service of 4-
6 years with professional training level among the university staff is
quite weak. This implies that good organization management lies on
the shoulders of the key leaders who enlighten the path to be
followed by the staff.
Abstract: The number of persons with implanted cardiac
pacemakers (PM) has increased in Western countries. The aim of this
paper is to investigate the possible situations where persons with a
PM may be exposed to extremely low frequency (ELF) electric (EF)
and magnetic fields (MF) that may disturb their PM. Based on our
earlier studies, it is possible to find such high public exposure to EFs
only in some places near 400 kV power lines, where an EF may
disturb a PM in unipolar mode. Such EFs cannot be found near 110
kV power lines. Disturbing MFs can be found near welding
machines. However, we do not have measurement data from welding.
Based on literature and earlier studies at Tampere University of
Technology, it is difficult to find public EF or MF exposure that is
high enough to interfere with PMs.