Abstract: The use of magnesium alloys is limited due to their
susceptibility to corrosion although they have many attractive
physical and mechanical properties. To increase mechanical and
corrosion properties of these alloys, many deposition method and
coating types are used. Electroless Ni–B coatings have received
considerable interest recently due to its unique properties such as
cost-effectiveness, thickness uniformity, good wear resistance,
lubricity, good ductility and corrosion resistance, excellent
solderability and electrical properties and antibacterial property. In
this study, electroless Ni-B coating could been deposited on AZ91
magnesium alloy. The obtained coating exhibited a harder and
rougher structure than the substrate.
Abstract: NiFe2O4 (nickel ferrite), ZnFe2O4 (zinc ferrite) and
Ni0.5Zn0.5Fe2O4 (nickel-zinc ferrite) were prepared by
mechanochemical route in a planetary ball mill starting from mixture
of the appropriate quantities of the Ni(OH)2/Fe(OH)3,
Zn(OH)2/Fe(OH)3 and Ni(OH)2/Zn(OH)2/Fe(OH)3 hydroxide
powders. In order to monitor the progress of chemical reaction and
confirm phase formation, powder samples obtained after 25 h, 18 h
and 10 h of milling were characterized by X-ray diffraction (XRD),
transmission electron microscopy (TEM), IR, Raman and Mössbauer
spectroscopy. It is shown that the soft mechanochemical method, i.e.
mechanochemical activation of hydroxides, produces high quality
single phase ferrite samples in much more efficient way. From the IR
spectroscopy of single phase samples it is obvious that energy of
modes depends on the ratio of cations. It is obvious that all samples
have more than 5 Raman active modes predicted by group theory in
the normal spinel structure. Deconvolution of measured spectra
allows one to conclude that all complex bands in the spectra are made
of individual peaks with the intensities that vary from spectrum to
spectrum. The deconvolution of Raman spectra allows to separate
contributions of different cations to a particular type of vibration and
to estimate the degree of inversion.
Abstract: This research tested the performance of alternative
warehouse designs concerning the picking process. The chosen
performance measures were Travel Distance and Total Fulfilment
Time. An explanatory case study was built up around a model
implemented with SIMUL8. Hypotheses were set by selecting
outcomes from the literature survey matching popular empirical
findings. 17.4% reductions were found for Total Fulfilment Time and
Resource Utilisation. The latter was then used as a proxy for
operational efficiency. Literal replication of theoretical data-patterns
was considered as an internal validity sign. Assessing the estimated
changes benefits ahead of implementation was found to be a
contribution to practice.
Abstract: Recent investigations have demonstrated the global
sea level rise due to climate change impacts. In this study, climate
changes study the effects of increasing water level in the strait of
Hormuz. The probable changes of sea level rise should be
investigated to employ the adaption strategies. The climatic output
data of a GCM (General Circulation Model) named CGCM3 under
climate change scenario of A1b and A2 were used. Among different
variables simulated by this model, those of maximum correlation
with sea level changes in the study region and least redundancy
among themselves were selected for sea level rise prediction by using
stepwise regression. One of models (Discrete Wavelet artificial
Neural Network) was developed to explore the relationship between
climatic variables and sea level changes. In these models, wavelet
was used to disaggregate the time series of input and output data into
different components and then ANN was used to relate the
disaggregated components of predictors and input parameters to each
other. The results showed in the Shahid Rajae Station for scenario
A1B sea level rise is among 64 to 75 cm and for the A2 Scenario sea
level rise is among 90 t0 105 cm. Furthermore, the result showed a
significant increase of sea level at the study region under climate
change impacts, which should be incorporated in coastal areas
management.
Abstract: The paper is focused on the operational model for
transport the single wagon consignments on railway network by
using two different models of train formation. The paper gives an
overview of possibilities of improving the quality of transport
services. Paper deals with two models used in problematic of train
formatting - time continuously and time discrete. By applying these
models in practice, the transport company can guarantee a higher
quality of service and expect increasing of transport performance.
The models are also applicable into others transport networks. The
models supplement a theoretical problem of train formation by new
ways of looking to affecting the organization of wagon flows.
Abstract: Targeted drug delivery is a method of delivering
medication to a patient in a manner that increases the concentration
of the medication in some parts of the body relative to others.
Targeted drug delivery seeks to concentrate the medication in the
tissues of interest while reducing the relative concentration of the
medication in the remaining tissues. This improves efficacy of the
while reducing side effects. In the present work, we investigate the
effect of magnetic field, flow rate and particle concentration on the
capturing of magnetic particles transported in a stent implanted
fluidic channel. Iron oxide magnetic nanoparticles (Fe3O4)
nanoparticles were synthesized via co-precipitation method. The
synthesized Fe3O4 nanoparticles were added in the de-ionized (DI)
water to prepare the Fe3O4 magnetic particle suspended fluid. This
fluid is transported in a cylindrical tube of diameter 8 mm with help
of a peristaltic pump at different flow rate (25-40 ml/min). A
ferromagnetic coil of SS 430 has been implanted inside the
cylindrical tube to enhance the capturing of magnetic nanoparticles
under magnetic field. The capturing of magnetic nanoparticles was
observed at different magnetic magnetic field, flow rate and particle
concentration. It is observed that capture efficiency increases from
47-67% at magnetic field 2-5kG, respectively at particle
concentration 0.6mg/ml and at flow rate 30 ml/min. However, the
capture efficiency decreases from 65 to 44% by increasing the flow
rate from 25 to 40 ml/min, respectively. Furthermore, it is observed
that capture efficiency increases from 51 to 67% by increasing the
particle concentration from 0.3 to 0.6 mg/ml, respectively.
Abstract: In present study, a large deposit of oolitic iron ore of
Late Carboniferous-Permotriassic-Lower Jurassic age was discovered
in Wadi Halfa and Argein areas, North Sudan. It seems that the iron
ore mineralization exists in the west and east bank of the River Nile
of the study area that are found on the Egyptian-Sudanese border.
The Carboniferous-Lower Jurassic age strata were covered by 67
sections and each section has been examined and carefully described.
The iron-ore in Wadi Halfa occurs as oolitic ironstone and contained
two horizons: (A) horizon and (B) horizon. Only horizon (A) was
observed in southern Argein area. The texture of the ore is variable
depending on the volume of the component. In thin sections, the
average of the ooids was ranged between 90%-80%. The matrix
varies between 10%-20% by volume and detritus quartz in other
component my reach up to 30% by volume in sandy massive ore.
Ooids size ranges from 0.2mm-1.00 mm on average in very coarse
ooids may attend up to 1 mm in size. The matrix around the ooids is
dominated by iron hydroxide, carbonate, fine, and amorphous silica.
The probable ore reserve estimate of 1.234 billion at a head grade of
41.29% Fe for the Wadi Halfa Oolitic Ironstone Formation. The iron
ore shows higher content of phosphorus ranges from 6.15% to 0.16%,
with mean 1.45%. The new technology Hatch–Ironstone Chloride
Segregation (HICS) can be used to produce commercial-quality of
iron and reduce phosphorus and silica to acceptable levels for steel
industry. The presence of infrastructures in addition to the presence
of massive quantities of iron ore would make exploitation
economically.
Abstract: At present, in China, the research about the urban
sustainability construction is still in the exploratory stage. The
ecological problems of the coastal area are more sensitive and
complicated. In the background of global warming with serious
ecological damage, this paper deeply researches on the main
characteristics of urban sustainability and measures how to build urban
sustainability. Through combining regional environmental with
economic ability along the coastal area, then authors put forward the
system planning framework, construction strategy and the evaluation
index system, in order to seek the way of building urban sustainability
along coastal area in China.
Abstract: The objective of this study was to synthesize and
characterize the poly(alkenoic acid)s with different molecular
structures, use these polymers to formulate a dental cement
restorative, and study the effect of molecular structures on reaction
kinetics, viscosity, and mechanical strengths of the formed polymers
and cement restoratives. In this study, poly(alkenoic acid)s with
different molecular structures were synthesized. The purified
polymers were formulated with commercial Fuji II LC glass fillers to
form the experimental cement restoratives. The reaction kinetics was
studied via 1HNMR spectroscopy. The formed restoratives were
evaluated using compressive strength, diametral tensile strength,
flexural strength, hardness and wear-resistance tests. Specimens were
conditioned in distilled water at 37oC for 24 h prior to testing. Fuji II
LC restorative was used as control. The results show that the higher
the arm number and initiator concentration, the faster the reaction
was. It was also found that the higher the arm number and branching
that the polymer had, the lower the viscosity of the polymer in water
and the lower the mechanical strengths of the formed restorative. The
experimental restoratives were 31-53% in compressive strength, 37-
55% in compressive modulus, 80-126% in diametral tensile strength,
76-94% in flexural strength, 4-21% in fracture toughness and 53-96%
in hardness higher than Fuji II LC. For wear test, the experimental
restoratives were only 5.4-13% of abrasive and 6.4-12% of attritional
wear depths of Fuji II LC in each wear cycle. The aging study also
showed that all the experimental restoratives increased their strength
continuously during 30 days, unlike Fuji II LC. It is concluded that
polymer molecular structures have significant and positive impact on
mechanical properties of dental cement restoratives.
Abstract: Increasingly complex modern power systems require
stability, especially for transient and small disturbances. Transient
stability plays a major role in stability during fault and large
disturbance. This paper compares a power system stabilizer (PSS)
and static Var compensator (SVC) to improve damping oscillation
and enhance transient stability. The effectiveness of a PSS connected
to the exciter and/or governor in damping electromechanical
oscillations of isolated synchronous generator was tested. The SVC
device is a member of the shunt FACTS (flexible alternating current
transmission system) family, utilized in power transmission systems.
The designed model was tested with a multi-machine system
consisting of four machines six bus, using MATLAB/SIMULINK
software. The results obtained indicate that SVC solutions are better
than PSS.
Abstract: Pure nickel coatings have been successfully
electrodeposited on copper substrates by the pulse plating technique.
The influence of current density, duty cycle and pulse frequency on
the surface morphology, crystal orientation, and microhardness was
determined. It was found that the crystallite size of the deposit
increases with increasing current density and duty cycle. The crystal
orientation progressively changed from a random texture at 1 A/dm2
to (200) texture at 10 A/dm2. Increasing pulse frequency resulted in
increased texture coefficient and peak intensity of (111) reflection.
An increase in duty cycle resulted in considerable increase in texture
coefficient and peak intensity of (311) reflection. Coatings obtained
at high current densities and duty cycle present a mixed morphology
of small and large grains. Maximum microhardness of 193 Hv was
achieved at 4 A/dm2, 10 Hz and duty cycle of 50%. Nickel coatings
with (200) texture are ductile while (111) texture improves the
microhardness of the coatings.
Abstract: Introduction: The process to build a better safety
culture, methods of error analysis, and preventive measures, starts
with an understanding of the effects when human factors engineering
refer to remote microscopic diagnosis in surgery and specially in
organ transplantation for the remote evaluation of the grafts. It has
been estimated that even in well-organized transplant systems an
average of 8% to 14% of the grafts (G) that arrive at the recipient
hospitals may be considered as diseased, injured, damaged or
improper for transplantation. Digital microscopy adds information on
a microscopic level about the grafts in Organ Transplant (OT), and
may lead to a change in their management. Such a method will
reduce the possibility that a diseased G, will arrive at the recipient
hospital for implantation. Aim: Ergonomics of Digital Microscopy
(DM) based on virtual slides, on Telemedicine Systems (TS) for
Tele-Pathological (TPE) evaluation of the grafts (G) in organ
transplantation (OT). Material and Methods: By experimental
simulation, the ergonomics of DM for microscopic TPE of Renal
Graft (RG), Liver Graft (LG) and Pancreatic Graft (PG) tissues is
analyzed. In fact, this corresponded to the ergonomics of digital
microscopy for TPE in OT by applying Virtual Slide (VS) system for
graft tissue image capture, for remote diagnoses of possible
microscopic inflammatory and/or neoplastic lesions. Experimentation
included: a. Development of an OTE-TS similar Experimental
Telemedicine System (Exp.-TS), b. Simulation of the integration of
TS with the VS based microscopic TPE of RG, LG and PG applying
DM. Simulation of the DM based TPE was performed by 2
specialists on a total of 238 human Renal Graft (RG), 172 Liver Graft
(LG) and 108 Pancreatic Graft (PG) tissues digital microscopic
images for inflammatory and neoplastic lesions on four electronic
spaces of the four used TS. Results: Statistical analysis of specialist‘s
answers about the ability to diagnose accurately the diseased RG, LG
and PG tissues on the electronic space among four TS (A,B,C,D)
showed that DM on TS for TPE in OT is elaborated perfectly on the
ES of a Desktop, followed by the ES of the applied Exp.-TS. Tablet
and Mobile-Phone ES seem significantly risky for the application of
DM in OT (p
Abstract: Lateral torsional buckling is a global buckling mode
which should be considered in design of slender structural members
under flexure about their strong axis. It is possible to compute the
load which causes lateral torsional buckling of a beam by finite
element analysis, however, closed form equations are needed in
engineering practice for calculation ease which can be obtained by
using energy method. In lateral torsional buckling applications of
energy method, a proper function for the critical lateral torsional
buckling mode should be chosen which can be thought as the
variation of twisting angle along the buckled beam. Accuracy of the
results depends on how close is the chosen function to the exact
mode. Since critical lateral torsional buckling mode of the cantilever
I-beams varies due to material properties, section properties and
loading case, the hardest step is to determine a proper mode function
in application of energy method. This paper presents an approximate function for critical lateral
torsional buckling mode of doubly symmetric cantilever I-beams.
Coefficient matrices are calculated for concentrated load at free end,
uniformly distributed load and constant moment along the beam
cases. Critical lateral torsional buckling modes obtained by presented
function and exact solutions are compared. It is found that the modes
obtained by presented function coincide with differential equation
solutions for considered loading cases.
Abstract: Cancer is still one of the serious diseases threatening
the lives of human beings. How to have an early diagnosis and
effective treatment for tumors is a very important issue. The animal
carcinoma model can provide a simulation tool for the studies of
pathogenesis, biological characteristics, and therapeutic effects.
Recently, drug delivery systems have been rapidly developed to
effectively improve the therapeutic effects. Liposome plays an
increasingly important role in clinical diagnosis and therapy for
delivering a pharmaceutic or contrast agent to the targeted sites.
Liposome can be absorbed and excreted by the human body, and is
well known that no harm to the human body. This study aimed to
compare the therapeutic effects between encapsulated (doxorubicin
liposomal, Lipodox) and un-encapsulated (doxorubicin, Dox)
anti-tumor drugs using magnetic resonance imaging (MRI).
Twenty-four New Zealand rabbits implanted with VX2 carcinoma at
left thighs were classified into three groups: control group (untreated),
Dox-treated group, and LipoDox-treated group, 8 rabbits for each
group. MRI scans were performed three days after tumor implantation.
A 1.5T GE Signa HDxt whole body MRI scanner with a high
resolution knee coil was used in this study. After a 3-plane localizer
scan was performed, three-dimensional (3D) fast spin echo (FSE)
T2-weighted Images (T2WI) was used for tumor volumetric
quantification. Afterwards, two-dimensional (2D) spoiled gradient
recalled echo (SPGR) dynamic contrast-enhanced (DCE) MRI was
used for tumor perfusion evaluation. DCE-MRI was designed to
acquire four baseline images, followed by contrast agent Gd-DOTA
injection through the ear vein of rabbit. A series of 32 images were
acquired to observe the signals change over time in the tumor and
muscle. The MRI scanning was scheduled on a weekly basis for a
period of four weeks to observe the tumor progression longitudinally.
The Dox and LipoDox treatments were prescribed 3 times in the first
week immediately after the first MRI scan; i.e. 3 days after VX2 tumor
implantation. ImageJ was used to quantitate tumor volume and time
course signal enhancement on DCE images. The changes of tumor size
showed that the growth of VX2 tumors was effectively inhibited for
both LipoDox-treated and Dox-treated groups. Furthermore, the tumor
volume of LipoDox-treated group was significantly lower than that of
Dox-treated group, which implies that LipoDox has better therapeutic effect than Dox. The signal intensity of LipoDox-treated group is
significantly lower than that of the other two groups, which implies
that targeted therapeutic drug remained in the tumor tissue. This study
provides a radiation-free and non-invasive MRI method for
therapeutic monitoring of targeted liposome on an animal tumor
model.
Abstract: Underwater acoustic networks have attracted great
attention in the last few years because of its numerous applications.
High data rate can be achieved by efficiently modeling the physical
layer in the network protocol stack. In Acoustic medium,
propagation speed of the acoustic waves is dependent on many
parameters such as temperature, salinity, density, and depth.
Acoustic propagation speed cannot be modeled using standard
empirical formulas such as Urick and Thorp descriptions. In this
paper, we have modeled the acoustic channel using real time data of
temperature, salinity, and speed of Bay of Bengal (Indian Coastal
Region). We have modeled the acoustic channel by using Mackenzie
speed equation and real time data obtained from National Institute of
Oceanography and Technology. It is found that acoustic propagation
speed varies between 1503 m/s to 1544 m/s as temperature and
depth differs. The simulation results show that temperature, salinity,
depth plays major role in acoustic propagation and data rate
increases with appropriate data sets substituted in the simulated
model.
Abstract: Fires is one of the main types of disturbances that
shape ecosystems in the Mediterranean region. However nowadays,
climate alterations towards higher temperatures result on increased
levels of fire intensity, frequency and spread as well as difficulties for
natural regeneration to occur. Thasos Island is one of the Greek
islands that has experienced those problems. Since 1984, a series of
wildfires led to the reduction of forest cover from 61.6% to almost
20%. The negative impacts were devastating in many different
aspects for the island. The absence of plant cover, post-wildfire
precipitation and steep slopes were the major factors that induced
severe soil erosion and intense floods. That also resulted to serious
economic problems to the local communities and the inability of the
burnt areas to regenerate naturally. Despite the substantial amount of
published work regarding Thasos wildfires, there is no information
related to post-wildfire effects on factors such as soil erosion. More
research related to post-fire effects should help to an overall
assessment of the negative impacts of wildfires on land degradation
through processes such as soil erosion and flooding.
Abstract: The garment manufacturing industry involves
sequential processes that are subjected to uncontrollable variations.
The industry depends on the skill of labour in handling the varieties
of fabrics and accessories, machines, as well as complicated sewing
operation. Due to these reasons, garment manufacturers have created
systems to monitor and to control the quality of the products on a
regular basis by conducting quality approaches to minimize variation.
With that, the aim of this research has been to ascertain the quality
approaches deployed by Malaysian garment manufacturers in three
key areas - quality systems and tools; quality control and types of
inspection; as well as sampling procedures chosen for garment
inspection. Besides, the focus of this research was to distinguish the
quality approaches adopted by companies that supplied finished
garments to both domestic and international markets. Feedback from
each company representative has been obtained via online survey,
which comprised of five sections and 44 questions on the
organizational profile and the quality approaches employed in the
garment industry. As a result, the response rate was 31%. The results
revealed that almost all companies have established their own
mechanism of process control by conducting a series of quality
inspections for daily production, either it was formally set up or
otherwise. In addition, quality inspection has been the predominant
quality control activity in the garment manufacturing, while the level
of complexity of these activities was substantially dictated by the
customers. Moreover, AQL-based sampling was utilized by
companies dealing with exports, whilst almost all the companies that
only concentrated on the domestic market were comfortable using
their own sampling procedures for garment inspection. Hence, this
research has provided insights into the implementation of a number
of quality approaches that were perceived as important and useful in
the garment manufacturing sector, which is truly labour-intensive.
Abstract: South Africa is in its post-industrial era moving from
the primary and secondary sector to the tertiary sector. The study
investigated the impact of the disaggregated energy consumption
(coal, oil, and electricity) on the primary, secondary and tertiary
sectors of the economy between 1980 and 2012 in South Africa.
Using vector error correction model, it was established that South
Africa is an energy dependent economy, and that energy (especially
electricity and oil) is a limiting factor of growth. This implies that
implementation of energy conservation policies may hamper
economic growth. Output growth is significantly outpacing energy
supply, which has necessitated load shedding. To meet up the excess
energy demand, there is a need to increase the generating capacity
which will necessitate increased investment in the electricity sector as
well as strategic steps to increase oil production. There is also need to
explore more renewable energy sources, in order to meet the growing
energy demand without compromising growth and environmental
sustainability. Policy makers should also pursue energy efficiency
policies especially at sectoral level of the economy.
Abstract: The aim of this study is to empirically investigate the
mediating impact of export performance (EP) between technological
advancement capabilities and business performance (BP) of
Malaysian manufacturing micro, small and medium sized enterprises
(MSME’s). Firm’s technological advancement resources are
hypothesized as a platform to enhance both exports and BP of
manufacturing MSMEs in Malaysia. This study is twofold, primary it
has investigated that technological advancement capabilities helps to
appreciates main performance measures noted in terms of EP and
Secondly, it investigates that how efficiently and effectively
technological advancement capabilities can contribute in overall
Malaysian MSME’s BP. Smart PLS-3 statistical software is used to
know the association between technological advancement
capabilities, MSME’s EP and BP. In this study, the data was
composed from Malaysian manufacturing MSME’s in east coast
industrial zones known as the manufacturing hub of MSMEs. Seven
hundred and fifty (750) questionnaires were distributed, but only 148
usable questionnaires are returned. The finding of this study indicated
that technological advancement capabilities helps to strengthen the
export in term of time and cost efficient and it plays a significant role
in appreciating their BP. This study is helpful for small and medium
enterprise owners who intend to expand their business overseas and
though smart technological advancement resources they can achieve
their business competitiveness and excellence both at local and
international markets.
Abstract: Hydraulic fracturing is one of the most important
stimulation techniques available to the petroleum engineer to extract
hydrocarbons in tight gas sandstones. It allows more oil and gas
production in tight reservoirs as compared to conventional means.
The main aim of the study is to optimize the hydraulic fracturing as
technique and for this purpose three multi-zones layer formation is
considered and fractured contemporaneously. The three zones are
named as Zone1 (upper zone), Zone2 (middle zone) and Zone3
(lower zone) respectively and they all occur in shale rock. Simulation was performed with Mfrac integrated software which
gives a variety of 3D fracture options. This simulation process
yielded an average fracture efficiency of 93.8%for the three
respective zones and an increase of the average permeability of the
rock system. An average fracture length of 909 ft with net height
(propped height) of 210 ft (average) was achieved. Optimum
fracturing results was also achieved with maximum fracture width of
0.379 inches at an injection rate of 13.01 bpm with 17995 Mscf of
gas production.