Abstract: This paper presents a power control for a Doubly Fed
Induction Generator (DFIG) using in Wind Energy Conversion
System (WECS) connected to the grid. The proposed control strategy
employs two nonlinear controllers, Backstipping (BSC) and slidingmode
controller (SMC) scheme to directly calculate the required
rotor control voltage so as to eliminate the instantaneous errors of
active and reactive powers. In this paper the advantages of BSC and
SMC are presented, the performance and robustness of this two
controller’s strategy are compared between them. First, we present a
model of wind turbine and DFIG machine, then a synthesis of the
controllers and their application in the DFIG power control.
Simulation results on a 1.5MW grid-connected DFIG system are
provided by MATLAB/Simulink.
Abstract: A flow column has been innovatively used in the
design of a new electrocoagulation reactor (ECR1) that will reduce
the temperature of water being treated; where the flow columns work
as a radiator for the water being treated. In order to investigate the
performance of ECR1 and compare it to that of traditional reactors;
600 mL water samples with an initial temperature of 350C were
pumped continuously through these reactors for 30 min at current
density of 1 mA/cm2. The temperature of water being treated was
measured at 5 minutes intervals over a 30 minutes period using a
thermometer. Additional experiments were commenced to investigate
the effects of initial temperature (15-350C), water conductivity (0.15
– 1.2 S) and current density (0.5 -3 mA/cm2) on the performance of
ECR1.
The results obtained demonstrated that the ECR1, at a current
density of 1 mA/cm2 and continuous flow model, reduced water
temperature from 350C to the vicinity of 280C during the first 15
minutes and kept the same level till the end of the treatment time.
While, the temperature increased from 28.1 to 29.80C and from 29.8
to 31.90C in the batch and the traditional continuous flow models
respectively. In term of initial temperature, ECR1 maintained the
temperature of water being treated within the range of 22 to 280C
without the need for external cooling system even when the initial
temperatures varied over a wide range (15 to 350C). The influent
water conductivity was found to be a significant variable that affect
the temperature. The desirable value of water conductivity is 0.6 S.
However, it was found that the water temperature increased rapidly
with a higher current density.
Abstract: Feature selection has been used in many fields such as
classification, data mining and object recognition and proven to be
effective for removing irrelevant and redundant features from the
original dataset. In this paper, a new design of distributed intrusion
detection system using a combination feature selection model based
on bees and decision tree. Bees algorithm is used as the search
strategy to find the optimal subset of features, whereas decision tree
is used as a judgment for the selected features. Both the produced
features and the generated rules are used by Decision Making Mobile
Agent to decide whether there is an attack or not in the networks.
Decision Making Mobile Agent will migrate through the networks,
moving from node to another, if it found that there is an attack on one
of the nodes, it then alerts the user through User Interface Agent or
takes some action through Action Mobile Agent. The KDD Cup 99
dataset is used to test the effectiveness of the proposed system. The
results show that even if only four features are used, the proposed
system gives a better performance when it is compared with the
obtained results using all 41 features.
Abstract: As the Silicon oxide scaled down in MOSFET
technology to few nanometers, gate Direct Tunneling (DT) in
Floating gate (FGMOSFET) devices has become a major concern for
analog designers. FGMOSFET has been used in many low-voltage
and low-power applications, however, there is no accurate model that
account for DT gate leakage in nano-scale. This paper studied and
analyzed different simulation models for FGMOSFET using TSMC
90-nm technology. The simulation results for FGMOSFET cascade
current mirror shows the impact of DT on circuit performance in
terms of current and voltage without the need for fabrication. This
works shows the significance of using an accurate model for
FGMOSFET in nan-scale technologies.
Abstract: Latin America is probably the region with greater
social inequality, contrary to the amount of rights enshrined in their
constitutions. In the last decade of the twentieth century, the area
resulted in significant changes to democratization and constitutional
changes. Through low-key public policy, political leaders activated
participation in the culture of human rights. The struggle for social
rights in Latin America has been a constant regulation. His
consecration at the constitutional level has chained search
application. The constitutionalization and judicial protection of these
rights have been crucial in countries like Argentina, Venezuela, Peru
and Colombia. This paper presents an analytical view on the
constitutionalization of social rights in the Latin American context
and its justiciability.
Abstract: Tannase (tannin acyl hydrolase, E.C.3.1.1.20) is an
important hydrolysable enzyme with innumerable applications and
industrial potential. In the present study, a kinetic model has been
developed for the batch fermentation used for the production of
tannase by A.flavus MTCC 3783. Maximum tannase activity of
143.30 U/ml was obtained at 96 hours under optimum operating
conditions at 35oC, an initial pH of 5.5 and with an inducer tannic
acid concentration of 3% (w/v) for a fermentation period of 120
hours. The biomass concentration reaches a maximum of 6.62 g/l at
96 hours and further there was no increase in biomass concentration
till the end of the fermentation. Various unstructured kinetic models
were analyzed to simulate the experimental values of microbial
growth, tannase activity and substrate concentration. The Logistic
model for microbial growth , Luedeking - Piret model for production
of tannase and Substrate utilization kinetic model for utilization of
substrate were capable of predicting the fermentation profile with
high coefficient of determination (R2) values of 0.980, 0.942 and
0.983 respectively. The results indicated that the unstructured models
were able to describe the fermentation kinetics more effectively.
Abstract: Mobile Ad hoc Network is a set of self-governing
nodes which communicate through wireless links. Dynamic topology
MANETs makes routing a challenging task. Various routing
protocols are there, but due to various fundamental characteristic
open medium, changing topology, distributed collaboration and
constrained capability, these protocols are tend to various types of
security attacks. Black hole is one among them. In this attack,
malicious node represents itself as having the shortest path to the
destination but that path not even exists. In this paper, we aim to
develop a routing protocol for detection and prevention of black hole
attack by modifying AODV routing protocol. This protocol is able to
detect and prevent the black hole attack. Simulation is done using
NS-2, which shows the improvement in network performance.
Abstract: This paper presents the results obtained by numerical
simulation using the software ANSYS CFX-CFD for the air
pollutants dispersion in the atmosphere coming from the evacuation
of combustion gases resulting from the fuel combustion in an electric
thermal power plant. The model uses the Navier-Stokes equation to
simulate the dispersion of pollutants in the atmosphere. It is
considered as important factors in elaboration of simulation the
atmospheric conditions (pressure, temperature, wind speed, wind
direction), the exhaust velocity of the combustion gases, chimney
height and the obstacles (buildings). Using the air quality monitoring
stations it is measured the concentrations of main pollutants (SO2,
NOx and PM). The pollutants were monitored over a period of 3
months, after that the average concentration are calculated, which is
used by the software. The concentrations are: 8.915 μg/m3 (NOx),
9.587 μg/m3 (SO2) and 42 μg/m3 (PM). A comparison of test data
with simulation results demonstrated that CFX was able to describe
the dispersion of the pollutant as well the concentration of this
pollutants in the atmosphere.
Abstract: In this paper, analysis of an infinite beam resting on
multilayer tensionless extensible geosynthetic reinforced granular
fill-poor soil system overlying soft soil strata under moving load with
constant velocity is presented. The beam is subjected to a
concentrated load moving with constant velocity. The upper
reinforced granular bed is modeled by a rough membrane embedded
in Pasternak shear layer overlying a series of compressible nonlinear
winkler springs representing the underlying the very poor soil. The
multilayer tensionless extensible geosynthetic layer has been
assumed to deform such that at interface the geosynthetic and the soil
have some deformation. Nonlinear behaviour of granular fill and the
very poor soil has been considered in the analysis by means of
hyperbolic constitutive relationships. Governing differential
equations of the soil foundation system have been obtained and
solved with the help of appropriate boundary conditions. The solution
has been obtained by employing finite difference method by means of
Gauss-Siedal iterative scheme. Detailed parametric study has been
conducted to study the influence of various parameters on the
response of soil–foundation system under consideration by means of
deflection and bending moment in the beam and tension mobilized in
the geosynthetic layer. These parameters include magnitude of
applied load, velocity of load, damping, ultimate resistance of poor
soil and granular fill layer. Range of values of parameters has been
considered as per Indian Railway conditions. This study clearly
observed that the comparisons of multilayer tensionless extensible
geosynthetic reinforcement with poor foundation soil and magnitude
of applied load, relative compressibility of granular fill and ultimate
resistance of poor soil has significant influence on the response of
soil–foundation system.
Abstract: The purpose of this study is the discrimination of 28
postmenopausal with osteoporotic femoral fractures from an agematched
control group of 28 women using texture analysis based on
fractals. Two pre-processing approaches are applied on radiographic
images; these techniques are compared to highlight the choice of the
pre-processing method. Furthermore, the values of the fractal
dimension are compared to those of the fractal signature in terms of
the classification of the two populations. In a second analysis, the
BMD measure at proximal femur was compared to the fractal
analysis, the latter, which is a non-invasive technique, allowed a
better discrimination; the results confirm that the fractal analysis of
texture on calcaneus radiographs is able to discriminate osteoporotic
patients with femoral fracture from controls. This discrimination was
efficient compared to that obtained by BMD alone. It was also
present in comparing subgroups with overlapping values of BMD.
Abstract: Method of combined teaching laws of classical
mechanics and hydrostatics in non-inertial reference frames for
undergraduate students is proposed. Pressure distribution in a liquid
(or gas) moving with acceleration is considered. Combined effect of
hydrostatic force and force of inertia on a body immersed in a liquid
can lead to paradoxical results, in a motion of pendulum in particular.
The body motion under Stokes force influence and forces in rotating
reference frames are investigated as well. Problems and difficulties in
student perceptions are analyzed.
Abstract: Propagation of arbitrary amplitude nonlinear Alfven
waves has been investigated in low but finite β electron-positron-ion
plasma including full ion dynamics. Using Sagdeev pseudopotential
method an energy integral equation has been derived. The Sagdeev
potential has been calculated for different plasma parameters and it
has been shown that inclusion of ion parallel motion along the
magnetic field changes the nature of slow shear Alfven wave solitons
from dip type to hump type. The effects of positron concentration,
plasma-β and obliqueness of the wave propagation on the solitary
wave structure have also been examined.
Abstract: The use of titanium fluoride and iron fluoride
(TiF3/FeF3) catalysts in combination with polutetrafluoroethylene
(PTFE) in plain zinc- dialkyldithiophosphate (ZDDP) oil is important
for the study of engine tribocomponents and is increasingly a strategy
to improve the formation of tribofilm and provide low friction and
excellent wear protection in reduced phosphorus plain ZDDP oil. The
influence of surface roughness and the concentration of
TiF3/FeF3/PTFE were investigated using bearing steel samples
dipped in lubricant solution at 100°C for two different heating time
durations. This paper addresses the effects of water drop contact
angle using different surface; finishes after treating them with
different lubricant combination. The calculated water drop contact
angles were analyzed using Design of Experiment software (DOE)
and it was determined that a 0.05 μm Ra surface roughness would
provide an excellent TiF3/FeF3/PTFE coating for antiwear resistance
as reflected in the Scanning electron microscopy (SEM) images and
the tribological testing under extreme pressure conditions. Both
friction and wear performance depend greatly on the PTFE/and
catalysts in plain ZDDP oil with 0.05 % phosphorous and on the
surface finish of bearing steel. The friction and wear reducing effects,
which was observed in the tribological tests, indicated a better micro
lubrication effect of the 0.05 μm Ra surface roughness treated at
100°C for 24 hours when compared to the 0.1 μm Ra surface
roughness with the same treatment.
Abstract: Singular value decomposition based optimisation of
geometric design parameters of a 5-speed gearbox is studied. During
the optimisation, a four-degree-of freedom torsional vibration model
of the pinion gear-wheel gear system is obtained and the minimum
singular value of the transfer matrix is considered as the objective
functions. The computational cost of the associated singular value
problems is quite low for the objective function, because it is only
necessary to compute the largest and smallest singular values (μmax
and μmin) that can be achieved by using selective eigenvalue solvers;
the other singular values are not needed. The design parameters are
optimised under several constraints that include bending stress,
contact stress and constant distance between gear centres. Thus, by
optimising the geometric parameters of the gearbox such as, the
module, number of teeth and face width it is possible to obtain a
light-weight-gearbox structure. It is concluded that the all optimised
geometric design parameters also satisfy all constraints.
Abstract: Particle size distribution, the most important
characteristics of aerosols, is obtained through electrical
characterization techniques. The dynamics of charged nanoparticles
under the influence of electric field in Electrical Mobility
Spectrometer (EMS) reveals the size distribution of these particles.
The accuracy of this measurement is influenced by flow conditions,
geometry, electric field and particle charging process, therefore by
the transfer function (transfer matrix) of the instrument. In this work,
a wire-cylinder corona charger was designed and the combined fielddiffusion
charging process of injected poly-disperse aerosol particles
was numerically simulated as a prerequisite for the study of a
multichannel EMS. The result, a cloud of particles with no uniform
charge distribution, was introduced to the EMS. The flow pattern and
electric field in the EMS were simulated using Computational Fluid
Dynamics (CFD) to obtain particle trajectories in the device and
therefore to calculate the reported signal by each electrometer.
According to the output signals (resulted from bombardment of
particles and transferring their charges as currents), we proposed a
modification to the size of detecting rings (which are connected to
electrometers) in order to evaluate particle size distributions more
accurately. Based on the capability of the system to transfer
information contents about size distribution of the injected particles,
we proposed a benchmark for the assessment of optimality of the
design. This method applies the concept of Von Neumann entropy
and borrows the definition of entropy from information theory
(Shannon entropy) to measure optimality. Entropy, according to the
Shannon entropy, is the ''average amount of information contained in
an event, sample or character extracted from a data stream''.
Evaluating the responses (signals) which were obtained via various
configurations of detecting rings, the best configuration which gave
the best predictions about the size distributions of injected particles,
was the modified configuration. It was also the one that had the
maximum amount of entropy. A reasonable consistency was also
observed between the accuracy of the predictions and the entropy
content of each configuration. In this method, entropy is extracted
from the transfer matrix of the instrument for each configuration.
Ultimately, various clouds of particles were introduced to the
simulations and predicted size distributions were compared to the
exact size distributions.
Abstract: The objective of the study is to assess the
implementation of LED lighting into forest machine work in the dark.
In addition, the paper includes a wide variety of important and
relevant safety and health parameters. In modern, computerized work
in the cab of forest machines, artificial illumination is a demanding
task when performing duties, such as the visual inspections of wood
and computer calculations. We interviewed entrepreneurs and
gathered the following as the most pertinent themes: (1) safety, (2)
practical problems, and (3) work with LED lighting. The most
important comments were in regards to the practical problems of
LED lighting. We found indications of technical problems in
implementing LED lighting, like snow and dirt on the surfaces of
lamps that dim the emission of light. Moreover, service work in the
dark forest is dangerous and increases the risks of on-site accidents.
We also concluded that the amount of blue light to the eyes should be
assessed, especially, when the drivers are working in a semi-dark cab.
Abstract: Nine Degrees of Freedom (9 DOF) systems are
already in development in many areas. In this paper, an integrated
pressure sensor is proposed that will make use of an already existing
monolithic 9 DOF inertial MEMS platform. Capacitive pressure
sensors can suffer from limited sensitivity for a given size of
membrane. This novel pressure sensor design increases the sensitivity
by over 5 times compared to a traditional array of square diaphragms
while still fitting within a 2 mm x 2 mm chip and maintaining a fixed
static capacitance. The improved design uses one large diaphragm
supported by pillars with fixed electrodes placed above the areas of
maximum deflection. The design optimization increases the
sensitivity from 0.22 fF/kPa to 1.16 fF/kPa. Temperature sensitivity
was also examined through simulation.
Abstract: This paper presents thermal annealing de-wetting
technique for the preparation of porous metal membrane for Thin
Film Encapsulation (TFE) application. Thermal annealing de-wetting
experimental results reveal that pore size formation in porous metal
membrane depend upon i.e. 1. The substrate at which metal is
deposited, 2. Melting point of metal used for porous metal cap layer
membrane formation, 3. Thickness of metal used for cap layer, 4.
Temperature used for formation of porous metal membrane. In order
to demonstrate this technique, Silver (Ag) was used as a metal for
preparation of porous metal membrane on amorphous silicon (a-Si)
and silicon oxide. The annealing of the silver thin film of various
thicknesses was performed at different temperature. Pores in porous
silver film were analyzed using Scanning Electron Microscope
(SEM). In order to check the usefulness of porous metal film for TFE
application, the porous silver film prepared on amorphous silicon (a-
Si) and silicon oxide was released using XeF2 and VHF, respectively.
Finally, guide line and structures are suggested to use this porous
membrane for robust TFE application.
Abstract: The purpose of this project is to propose a quick and
environmentally friendly alternative to measure the quality of oils
used in food industry. There is evidence that repeated and
indiscriminate use of oils in food processing cause physicochemical
changes with formation of potentially toxic compounds that can
affect the health of consumers and cause organoleptic changes. In
order to assess the quality of oils, non-destructive optical techniques
such as Interferometry offer a rapid alternative to the use of reagents,
using only the interaction of light on the oil. Through this project, we
used interferograms of samples of oil placed under different heating
conditions to establish the changes in their quality. These
interferograms were obtained by means of a Mach-Zehnder
Interferometer using a beam of light from a HeNe laser of 10mW at
632.8nm. Each interferogram was captured, analyzed and measured
full width at half-maximum (FWHM) using the software from
Amcap and ImageJ. The total of FWHMs was organized in three
groups. It was observed that the average obtained from each of the
FWHMs of group A shows a behavior that is almost linear, therefore
it is probable that the exposure time is not relevant when the oil is
kept under constant temperature. Group B exhibits a slight
exponential model when temperature raises between 373 K and 393
K. Results of the t-Student show a probability of 95% (0.05) of the
existence of variation in the molecular composition of both samples.
Furthermore, we found a correlation between the Iodine Indexes
(Physicochemical Analysis) and the Interferograms (Optical
Analysis) of group C. Based on these results, this project highlights
the importance of the quality of the oils used in food industry and
shows how Interferometry can be a useful tool for this purpose.
Abstract: This paper introduces a boost converter with a new
active snubber cell. In this circuit, all of the semiconductor
components in the converter softly turns on and turns off with the
help of the active snubber cell. Compared to the other converters, the
proposed converter has advantages of size, number of components
and cost. The main feature of proposed converter is that the extra
voltage stresses do not occur on the main switches and main diodes.
Also, the current stress on the main switch is acceptable level.
Moreover, the proposed converter can operates under light load
conditions and wide input line voltage. In this study, the operating
principle of the proposed converter is presented and its operation is
verified with the Proteus simulation software for a 1 kW and 100 kHz
model.