Abstract: Electromagnetic interference (EMI) is one of the
serious problems in most electrical and electronic appliances
including fluorescent lamps. The electronic ballast used to regulate
the power flow through the lamp is the major cause for EMI. The
interference is because of the high frequency switching operation of
the ballast. Formerly, some EMI mitigation techniques were in
practice, but they were not satisfactory because of the hardware
complexity in the circuit design, increased parasitic components and
power consumption and so on. The majority of the researchers have
their spotlight only on EMI mitigation without considering the other
constraints such as cost, effective operation of the equipment etc. In
this paper, we propose a technique for EMI mitigation in fluorescent
lamps by integrating Frequency Modulation and Evolutionary
Programming. By the Frequency Modulation technique, the
switching at a single central frequency is extended to a range of
frequencies, and so, the power is distributed throughout the range of
frequencies leading to EMI mitigation. But in order to meet the
operating frequency of the ballast and the operating power of the
fluorescent lamps, an optimal modulation index is necessary for
Frequency Modulation. The optimal modulation index is determined
using Evolutionary Programming. Thereby, the proposed technique
mitigates the EMI to a satisfactory level without disturbing the
operation of the fluorescent lamp.
Abstract: The adsorption of simulated aqueous solution containing textile remazol reactive dye, namely Red 3BS by palm shell activated carbon (PSAC) as adsorbent was carried out using Response Surface Methodology (RSM). A Box-Behnken design in three most important operating variables; initial dye concentration, dosage of adsorbent and speed of impeller was employed for experimental design and optimization of results. The significance of independent variables and their interactions were tested by means of the analysis of variance (ANOVA) with 95% confidence limits. Model indicated that with the increasing of dosage and speed give the result of removal up to 90% with the capacity uptake more than 7 mg/g. High regression coefficient between the variables and the response (R-Sq = 93.9%) showed of good evaluation of experimental data by polynomial regression model.
Abstract: Titanium oxide hollow microspheres were synthesized from organic precursor titanium tetraisopropoxide (TTIP) using continuous spray pyrolysis reactor. Effects of precursor concentration, applied voltage and annealing have been investigated. It was observed that the annealing of the as-synthesized TiO2 hollow microspheres at 2500C, which had an average external diameter of 200 nm, leads to an increase in the size and also more spherical shape. The precursor concentration was found to have a direct impact on the size of the microspheres, which is also evident in the absorption spectrum. The as-prepared TiO2 hollow microspheres exhibited good photocatalytic activity for the degradation of MO.
Abstract: The radiative exchange method is introduced as a
numerical method for the simulation of radiative heat transfer in an
absorbing, emitting and isotropically scattering media. In this
method, the integro-differential radiative balance equation is solved
by using a new introduced concept for the exchange factor. Even
though the radiative source term is calculated in a mesh structure that
is coarser than the structure used in computational fluid dynamics,
calculating the exchange factor between different coarse elements by
using differential integration elements makes the result of the method
close to that of integro-differential radiative equation. A set of
equations for calculating exchange factors in two and threedimensional
Cartesian coordinate system is presented, and the
method is used in the simulation of radiative heat transfer in twodimensional
rectangular case and a three-dimensional simple cube.
The result of using this method in simulating different cases is
verified by comparing them with those of using other numerical
radiative models.
Abstract: State-dependent Riccati equation based controllers are
becoming increasingly popular because of having attractive
properties like optimality, stability and robustness. This paper focuses
on the design of a roll autopilot for a fin stabilized and canard
controlled 122mm artillery rocket using state-dependent Riccati
equation technique. Initial spin is imparted to rocket during launch
and it quickly decays due to straight tail fins. After the spin phase, the
roll orientation of rocket is brought to zero with the canard deflection
commands generated by the roll autopilot. Roll autopilot has been
developed by considering uncoupled roll, pitch and yaw channels.
The canard actuator is modeled as a second-order nonlinear system.
Elements of the state weighing matrix for Riccati equation have been
chosen to be state dependent to exploit the design flexibility offered
by the Riccati equation technique. Simulation results under varying
conditions of flight demonstrate the wide operating range of the
proposed autopilot.
Abstract: This article presents new current-mode oscillator circuits using CDTAs which is designed from block diagram. The proposed circuits consist of two CDTAs and two grounded capacitors. The condition of oscillation and the frequency of oscillation can be adjusted by electronic method. The circuits have high output impedance and use only grounded capacitors without any external resistor which is very appropriate to future development into an integrated circuit. The results of PSPICE simulation program are corresponding to the theoretical analysis.
Abstract: With the growth of electricity generation from gas
energy gas pipeline reliability can substantially impact the electric
generation. A physical disruption to pipeline or to a compressor
station can interrupt the flow of gas or reduce the pressure and lead
to loss of multiple gas-fired electric generators, which could
dramatically reduce the supplied power and threaten the power
system security. Gas pressure drops during peak loading time on
pipeline system, is a common problem in network with no enough
transportation capacity which limits gas transportation and causes
many problem for thermal domain power systems in supplying their
demand. For a feasible generation scheduling planning in networks
with no sufficient gas transportation capacity, it is required to
consider gas pipeline constraints in solving the optimization problem
and evaluate the impacts of gas consumption in power plants on gas
pipelines operating condition. This paper studies about operating of
gas fired power plants in critical conditions when the demand of gas
and electricity peak together. An integrated model of gas and electric
model is used to consider the gas pipeline constraints in the economic
dispatch problem of gas-fueled thermal generator units.
Abstract: The recent developments in computing and
communication technology permit to users to access multimedia
documents with variety of devices (PCs, PDAs, mobile phones...)
having heterogeneous capabilities. This diversification of supports
has trained the need to adapt multimedia documents according to
their execution contexts. A semantic framework for multimedia
document adaptation based on the conceptual neighborhood graphs
was proposed. In this framework, adapting consists on finding
another specification that satisfies the target constraints and which is
as close as possible from the initial document. In this paper, we
propose a new way of building the conceptual neighborhood graphs
to best preserve the proximity between the adapted and the original
documents and to deal with more elaborated relations models by
integrating the relations relaxation graphs that permit to handle the
delays and the distances defined within the relations.
Abstract: This research proposes a methodology for patent-citation-based technology input-output analysis by applying the patent information to input-output analysis developed for the dependencies among different industries. For this analysis, a technology relationship matrix and its components, as well as input and technology inducement coefficients, are constructed using patent information. Then, a technology inducement coefficient is calculated by normalizing the degree of citation from certain IPCs to the different IPCs (International patent classification) or to the same IPCs. Finally, we construct a Dependency Structure Matrix (DSM) based on the technology inducement coefficient to suggest a useful application for this methodology.
Abstract: A Data Warehouses is a repository of information
integrated from source data. Information stored in data warehouse is
the form of materialized in order to provide the better performance
for answering the queries. Deciding which appropriated views to be
materialized is one of important problem. In order to achieve this
requirement, the constructing search space close to optimal is a
necessary task. It will provide effective result for selecting view to be
materialized. In this paper we have proposed an approach to reoptimize
Multiple View Processing Plan (MVPP) by using global
common subexpressions. The merged queries which have query
processing cost not close to optimal would be rewritten. The
experiment shows that our approach can help to improve the total
query processing cost of MVPP and sum of query processing cost
and materialized view maintenance cost is reduced as well after views
are selected to be materialized.
Abstract: A frictionless contact problem for a two-layer orthotropic elastic medium loaded through a rigid flat stamp is considered. It is assumed that tensile tractions are not allowed and only compressive tractions can be transmitted across the interface. In the solution, effect of gravity is taken into consideration. If the external load on the rigid stamp is less than or equal to a critical value, continuous contact between the layers is maintained. The problem is expressed in terms of a singular integral equation by using the theory of elasticity and the Fourier transforms. Numerical results for initial separation point, critical separation load and contact stress distribution are presented.
Abstract: Stick models are widely used in studying the
behaviour of straight as well as skew bridges and viaducts subjected
to earthquakes while carrying out preliminary studies. The
application of such models to highly curved bridges continues to
pose challenging problems. A viaduct proposed in the foothills of the
Himalayas in Northern India is chosen for the study. It is having 8
simply supported spans @ 30 m c/c. It is doubly curved in horizontal
plane with 20 m radius. It is inclined in vertical plane as well. The
superstructure consists of a box section. Three models have been
used: a conventional stick model, an improved stick model and a 3D
finite element model. The improved stick model is employed by
making use of body constraints in order to study its capabilities. The
first 8 frequencies are about 9.71% away in the latter two models.
Later the difference increases to 80% in 50th mode. The viaduct was
subjected to all three components of the El Centro earthquake of May
1940. The numerical integration was carried out using the Hilber-
Hughes-Taylor method as implemented in SAP2000. Axial forces
and moments in the bridge piers as well as lateral displacements at
the bearing levels are compared for the three models. The maximum
difference in the axial forces and bending moments and
displacements vary by 25% between the improved and finite element
model. Whereas, the maximum difference in the axial forces,
moments, and displacements in various sections vary by 35%
between the improved stick model and equivalent straight stick
model. The difference for torsional moment was as high as 75%. It is
concluded that the stick model with body constraints to model the
bearings and expansion joints is not desirable in very sharp S curved
viaducts even for preliminary analysis. This model can be used only
to determine first 10 frequency and mode shapes but not for member
forces. A 3D finite element analysis must be carried out for
meaningful results.
Abstract: Previous studies mass evacuation route network does
not fully reflect the step-by-step behavior and evacuees make routing
decisions. Therefore, they do not work as expected when applied to the
evacuation route planning is valid. This article describes where
evacuees may have to make a direction to select all areas were
identified as guiding points to improve evacuation routes network.
This improved route network can be used as a basis for the layout can
be used to guide the signs indicate that provides the required
evacuation direction. This article also describes that combines
simulation and artificial bee colony algorithm to provide the proposed
routing solutions, to plan an integrated routing mode. The improved
network and the model used is the cinema as a case study to assess the
floor. The effectiveness of guidance solution in the total evacuation
time is significant by verification.
Abstract: There are various approaches to implement quality
improvements. Organizations aim for a management standard which
is capable of providing customers with quality assurance on their
product/service via continuous process improvement. Carefully
planned steps are necessary to ensure the right quality improvement
methodology (QIM) and business operations are consistent, reliable
and truly meet the customers' needs. This paper traces the evolution
of QIM in Malaysia-s Information Technology (IT) industry in the
past, current and future; and highlights some of the thought of
researchers who contributed to the science and practice of quality,
and identifies leading methodologies in use today. Some of the
misconceptions and mistakes leading to quality system failures will
also be examined and discussed. This paper aims to provide a general
overview of different types of QIMs available for IT businesses in
maximizing business advantages, enhancing product quality,
improving process routines and increasing performance earnings.
Abstract: Green Lean Total Quality Management (LTQM) Human Resource Management (HRM) System is a system comprises of HRM in Environmental Management System (EMS) practices which is integrated to TQM with Lean Manufacturing (LM) principles. HRM is essential especially in dealing with low motivation and less productive employees. The ultimate goal of this system is to focus on achieving total human resource development that is motivated and capable to optimize their creativity to be a part of Green and Lean TQM organization. A survey questionnaire was developed and distributed to 30 highly active automotive vendors in Malaysia and analyzed by Minitab v16 and SPSS v17. It was found out companies that are practicing Green LTQM HRM practices have generated more revenue and have RND capability. However, years of company establishment do not affect the openness of the company to adapt new initiatives that can help to improve the effectiveness of the operations. It was also found out the importance of training, communication and rewards for employees. The Green LTQM HRM practices framework model established in this study hopefully will give preliminary insight especially to companies that are still looking for system that can improve their productivity from managing human resource. This is preliminary study that combined 4 awards practices, ISO/TS16949, Toyota Production System SAEJ4000, MAJAICO Lean Production System and EMS focusing on highly active companies that have been involved in MAJAICO Program and Proton Vendor Development Program. Future study can be conducted to know the status at other industry as well as case study pertaining to this system.
Abstract: Early supplier involvement (ESI) benefits new
product development projects several ways. Nevertheless, many castuser
companies do not know the advantages of ESI and therefore do
not utilize it. This paper presents reasons why to utilize ESI in
casting industry and how that can be done. Further, this paper
presents advantages and challenges related to ESI in casting industry,
and introduces a Casting-Network Collaboration Model. The model
presents practices for companies to build advantageous collaborative
relationships. More detailed, the model describes three levels for
company-network relationships in casting industry with different
degrees of collaboration, and requirements for operating in each
level. In our research, ESI was found to influence, for example, on
project time, component cost, and quality. In addition, challenges
related to ESI, such as, a lack of mutual trust and unawareness about
the advantages were found. Our research approach was a case study
including four cases.
Abstract: This paper develops the fiscal health index of 21 local
governments in Taiwan over the 1984 to 2010 period. A quantile
regression analysis was used to explore the extent that economic
variables, political budget cycles, and legislative checks and balances,
impact different quantiles of fiscal health index for a country over a
sample period of time. Our findings suggest that local governments at
the lower quantile are significantly benefited from political budget
cycles and the increase in central government revenues, while
legislative effective checks and balances and the increase in central
government expenditures have a significantly negative effect on local
fiscal health. When local governments are in the upper tail of the
distribution, legislative checks and balances and growth in
macroeconomics have significant and adverse effects on the fiscal
health of local governments. However, increases in central
government revenues have significant and positive effects on the
health status of local government in Taiwan.
Abstract: In this paper, we present optimal control for
movement and trajectory planning for four degrees-of-freedom robot
using Fuzzy Logic (FL) and Genetic Algorithms (GAs). We have
evaluated using Fuzzy Logic (FL) and Genetic Algorithms (GAs)
for four degree-of-freedom (4 DOF) robotics arm, Uncertainties like;
Movement, Friction and Settling Time in robotic arm movement
have been compensated using Fuzzy logic and Genetic Algorithms.
The development of a fuzzy genetic optimization algorithm is
presented and discussed. The result are compared only GA and
Fuzzy GA. This paper describes genetic algorithms, which is
designed to optimize robot movement and trajectory. Though the
model represents is a general model for redundant structures and
could represent any n-link structures. The result is a complete
trajectory planning with Fuzzy logic and Genetic algorithms
demonstrating the flexibility of this technique of artificial
intelligence.
Abstract: Recent advancements in sensor technologies and
Wireless Body Area Networks (WBANs) have led to the
development of cost-effective healthcare devices which can be used
to monitor and analyse a person-s physiological parameters from
remote locations. These advancements provides a unique opportunity
to overcome current healthcare challenges of low quality service
provisioning, lack of easy accessibility to service varieties, high costs
of services and increasing population of the elderly experienced
globally. This paper reports on a prototype implementation of an
architecture that seamlessly integrates Wireless Body Area Network
(WBAN) with Web services (WS) to proactively collect
physiological data of remote patients to recommend diagnostic
services. Technologies based upon WBAN and WS can provide
ubiquitous accessibility to a variety of services by allowing
distributed healthcare resources to be massively reused to provide
cost-effective services without individuals physically moving to the
locations of those resources. In addition, these technologies can
reduce costs of healthcare services by allowing individuals to access
services to support their healthcare. The prototype uses WBAN body
sensors implemented on arduino fio platforms to be worn by the
patient and an android smart phone as a personal server. The
physiological data are collected and uploaded through GPRS/internet
to the Medical Health Server (MHS) to be analysed. The prototype
monitors the activities, location and physiological parameters such as
SpO2 and Heart Rate of the elderly and patients in rehabilitation.
Medical practitioners would have real time access to the uploaded
information through a web application.
Abstract: Mung bean starches were subjected to heat-moisture treatment (HMT) by different moisture contents (15%, 20%, 25%, 30% and 35%) at 120Ôäâ for 12h. The impact on the yields of resistant starch (RS), microstructure, physicochemical and functional properties was investigated. Compared to native starch, the RS content of heat-moisture treated starches increased significantly. The RS level of HMT-20 was the highest of all the starches. Birefringence was displayed clear at the center of native starch. For HMT starches, pronounced birefringence was exhibited on the periphery of starch granules; however, birefringence disappeared at the centre of some starch granules. The shape of HMT starches hadn-t been changed and the integrity of starch granules was preserved for all the conditions. Concavity could be observed on HMT starches under scanning electronic microscopy. After HMT, apparent amylose contents were increased and starch macromolecule was degraded in comparison with those of native starch. There was a reduction in swelling power on HMT starches, but the solubility of HMT starches was higher than that of native starch. Both of native and HMT starches showed A-type X-ray diffraction pattern. Furthermore, there is a higher intensity at the peak of 15.0 and 22.9 Å than those of native starch.