Abstract: Composite materials, due to their unique properties
such as high strength to weight ratio, corrosion resistance, and impact
resistance have huge potential as structural materials in automotive,
construction and transportation applications. However, these
properties often come at higher cost owing to complex design
methods, difficult manufacturing processes and raw material cost.
Traditionally, tapered laminated composite structures are
manufactured using autoclave manufacturing process by ply drop off
technique. Autoclave manufacturing though very powerful suffers
from high capital investment and higher energy consumption. As per
the current trends in composite manufacturing, Out of Autoclave
(OoA) processes are looked as emerging technologies for
manufacturing the structural composite components for aerospace
and defense applications. However, there is a need for improvement
among these processes to make them reliable and consistent. In this
paper, feasibility of using out of autoclave process to manufacture the
variable thickness cantilever beam is discussed. The minimum weight
design for the composite beam is obtained using constant stress beam
concept by tailoring the thickness of the beam. Ply drop off
techniques was used to fabricate the variable thickness beam from
glass/epoxy prepregs. Experiments were conducted to measure
bending stresses along the span of the cantilever beam at different
intervals by applying the concentrated load at the free end.
Experimental results showed that the stresses in the bean at different
intervals were constant. This proves the ability of OoA process to
manufacture the constant stress beam. Finite element model for the
constant stress beam was developed using commercial finite element
simulation software. It was observed that the simulation results
agreed very well with the experimental results and thus validated
design and manufacturing approach used.
Abstract: The effect of the inclusion of thyme and rosemary
essential oils into chitosan films, as well as the microbiological and
physical properties when storing chitosan film with and without the
mentioned inclusion was studied. The film forming solution was
prepared by dissolving chitosan (2%, w/v), polysorbate 80 (4% w/w
CH) and glycerol (16% w/w CH) in aqueous lactic acid solutions
(control). The thyme (TEO) and rosemary (REO) essential oils (EOs)
were included 1:1 w/w (EOs:CH) on their combination 50/50
(TEO:REO). The films were stored at temperatures of 5, 20, 33°C
and a relative humidity of 75% during four weeks. The films with
essential oil inclusion did not show an antimicrobial activity against
strains. This behavior could be explained because the chitosan only
inhibits the growth of microorganisms in direct contact with the
active sites. However, the inhibition capacity of TEO was higher than
the REO and a synergic effect between TEO:REO was found for S.
enteritidis strains in the chitosan solution.
Some physical properties were modified by the inclusion of
essential oils. The addition of essential oils does not affect the
mechanical properties (tensile strength, elongation at break, puncture
deformation), the water solubility, the swelling index nor the DSC
behavior. However, the essential oil inclusion can significantly
decrease the thickness, the moisture content, and the L* value of
films whereas the b* value increased due to molecular interactions
between the polymeric matrix, the loosing of the structure, and the
chemical modifications. On the other hand, the temperature and time
of storage changed some physical properties on the chitosan films.
This could have occurred because of chemical changes, such as
swelling in the presence of high humidity air and the reacetylation of
amino groups. In the majority of cases, properties such as moisture
content, tensile strength, elongation at break, puncture deformation,
a*, b*, chrome, 7E increased whereas water resistance, swelling
index, L*, and hue angle decreased.
Abstract: Replacement of plastics used in the food industry
seems to be a serious issue to overcome mainly the environmental
problems in recent years. This study investigates the hydrophilicity
and permeability properties of starch biopolymer which ethylene
vinyl alcohol (EVOH) (0-10%) and nanocrystalline cellulose (NCC)
(1-15%) were used to enhance its properties. Starch -EVOH
nanocomposites were prepared by casting method in different
formulations. NCC production by acid hydrolysis was confirmed by
scanning electron microscopy. Solubility, water vapor permeability,
water vapor transmission rate and moisture absorbance were
measured on each of the nanocomposites. The results were analyzed
by SAS software. The lowest moisture absorbance was measured in
pure starch nanocomposite containing 8% NCC. The lowest
permeability to water vapor belongs to starch nanocomposite
containing 8% NCC and the sample containing 7.8% EVOH and 13%
NCC. Also the lowest solubility was observed in the composite
contains the highest amount of EVOH. Applied Process resulted in
production of bio films which have good resistance to water vapor
permeability and solubility in water. The use of NCC and EVOH
leads to reduced moisture absorbance property of the biofilms.
Abstract: Examining existing experimental results for shallow
rigid foundations subjected to vertical centric load (N), accompanied
or not with a bending moment (M), two main non-linear mechanisms
governing the cyclic response of the soil-foundation system can be
distinguished: foundation uplift and soil yielding. A soil-foundation
failure limit, is defined as a domain of resistance in the two
dimensional (2D) load space (N, M) inside of which lie all the
admissible combinations of loads; these latter correspond to a pure
elastic, non-linear elastic or plastic behavior of the soil-foundation
system, while the points lying on the failure limit correspond to a
combination of loads leading to a failure of the soil-foundation
system. In this study, the proposed resistance domain is constructed
analytically based on mechanics. Original elastic limit, uplift
initiation limit and iso-uplift limits are constructed inside this
domain. These limits give a prediction of the mechanisms activated
for each combination of loads applied to the foundation. A
comparison of the proposed failure limit with experimental tests
existing in the literature shows interesting results. Also, the
developed uplift initiation limit and iso-uplift curves are confronted
with others already proposed in the literature and widely used due to
the absence of other alternatives, and remarkable differences are
noted, showing evident errors in the past proposals and relevant
accuracy for those given in the present work.
Abstract: In situ modified cyclohexanone-formaldehyde resins
were prepared by addition of alendronic acid during resin
preparation. Clay nanocomposites in ketonic resins were achieved by
adding clay into the flask at the beginning of the resin preparation.
The prepared resins were used for the synthesis of fire resistant
polyurethanes foam. Both phosphorous containing modifier
compound alendronic acid and nanoclay increases fire resistance of
the cyclohexanone-formaldehyde resin thus polyurethane produced
from these resins. The effect of the concentrations of alendronic acid
and clay on the fire resistance and physical properties of
polyurethanes was studied.
Abstract: The most important component affecting the
efficiency of photovoltaic power systems are solar panels. In other
words, efficiency of these systems are significantly affected due to
the being low efficiency of solar panel. Thus, solar panels should be
operated under maximum power point conditions through a power
converter. In this study, design of boost converter has been carried
out with maximum power point tracking (MPPT) algorithm which is
incremental conductance (Inc-Cond). By using this algorithm,
importance of power converter in MPPT hardware design, impacts of
MPPT operation have been shown. It is worth noting that initial
operation point is the main criteria for determining the MPPT
performance. In addition, it is shown that if value of load resistance is
lower than critical value, failure operation is realized. For these
analyzes, direct duty control is used for simplifying the control.
Abstract: Currently, thorium fuel has been especially noticed
because of its proliferation resistance than long half-life alpha emitter
minor actinides, breeding capability in fast and thermal neutron flux
and mono-isotopic naturally abundant. In recent years, efficiency of
minor actinide burning up in PWRs has been investigated. Hence, a
minor actinide-contained thorium based fuel matrix can confront both
proliferation resistance and nuclear waste depletion aims. In the
present work, minor actinide depletion rate in a CANDU-type nuclear
core modeled using MCNP code has been investigated. The obtained
effects of minor actinide load as mixture of thorium fuel matrix on
the core neutronics has been studied with comparing presence and
non-presence of minor actinide component in the fuel matrix.
Depletion rate of minor actinides in the MA-contained fuel has been
calculated using different power loads. According to the obtained
computational data, minor actinide loading in the modeled core
results in more negative reactivity coefficients. The MA-contained
fuel achieves less radial peaking factor in the modeled core. The
obtained computational results showed 140 kg of 464 kg initial load
of minor actinide has been depleted in during a 6-year burn up in 10
MW power.
Abstract: In this study, we are interested in a species of the
family of Asteraceae (Tagetes erecta). This family is considered as a
source of antimicrobial extracts with strong capacity. The extraction
of the flavonoids is carried out by the method of liquid/liquid with the
use of successive solvents. Afterwards, we evaluated the biological
activity of the flavonoids on five pathogenic bacterial stocks such as
Escherichia coli, Bacillus subtilis, Klebsiella pneumoniae,
Pseudomonas aeruginosa and Staphylococcus aureus and two stocks
of yeasts to knowing Candida albicans) and Saccharomyces
cerevisiae, by employing the method of the aromatogramme starting
from a solid disc. The result of the antimicrobial activity shows an
action and a variable degree of sensitivity according to bacterial
stocks tested. It will be noted that the flavonoids have an inhibiting
effect on E. coli, B. subtilis, K. pneumoniae and S. aureus. But a
resistance with respect to the extract by P. aeruginosa, C. albicans
and S. cerevisiae is to be mentioned.
Abstract: This paper investigates the viability of using carbon
fiber reinforced epoxy composites modified with carbon nanotubes to
strengthening reinforced concrete (RC) columns. Six RC columns
was designed and constructed according to ASCE standards. The
columns were wrapped using carbon fiber sheets impregnated with
either neat epoxy or CNTs modified epoxy. These columns were then
tested under concentric axial loading. Test results show that;
compared to the unwrapped specimens; wrapping concrete columns
with carbon fiber sheet embedded in CNTs modified epoxy resulted
in an increase in its axial load resistance, maximum displacement,
and toughness values by 24%, 109% and 232%, respectively. These
results reveal that adding CNTs into epoxy resin enhanced the
confinement effect, specifically, increased the axial load resistance,
maximum displacement, and toughness values by 11%, 6%, and
19%, respectively compared with columns strengthening with carbon
fiber sheet embedded in neat epoxy.
Abstract: To develop AZ91D magnesium alloys with improved
properties, we have applied TiN and VN/TiN multilayer coatings
using DC magnetron sputter technique. Coating structure, surface
morphology, chemical bonding and corrosion resistance of coatings
were analyzed by x-ray diffraction (XRD), scanning electron
microscope (SEM), x-ray photoelectron spectroscopy (XPS), and
tafel extrapolation method, respectively. XPS analysis reveal that VN
overlayer reacts with oxygen at the VN/TiN interface and forms more
stable TiN layer. Morphological investigations and the corrosion
results show that VN/TiN multilayer thin film coatings are quite
effective to optimize the corrosion resistance of Mg alloys.
Abstract: Metal matrix composites (MMCs) attract considerable
attention as a result from its ability in providing a high strength, high
modulus, high toughness, high impact properties, improving wear
resistance and providing good corrosion resistance compared to
unreinforced alloy. Aluminium Silicon (Al/Si) alloy MMC has been
widely used in various industrial sectors such as in transportation,
domestic equipment, aerospace, military, construction, etc.
Aluminium silicon alloy is an MMC that had been reinforced with
aluminium nitrate (AlN) particle and become a new generation
material use in automotive and aerospace sector. The AlN is one of
the advance material that have a bright prospect in future since it has
features such as lightweight, high strength, high hardness and
stiffness quality. However, the high degree of ceramic particle
reinforcement and the irregular nature of the particles along the
matrix material that contribute to its low density is the main problem
which leads to difficulties in machining process. This paper examined
the tool wear when milling AlSi/AlN Metal Matrix Composite using
a TiB2 (Titanium diboride) coated carbide cutting tool. The volume
of the AlN reinforced particle was 10% and milling process was
carried out under dry cutting condition. The TiB2 coated carbide
insert parameters used were at the cutting speed of (230, 300 and
370m/min, feed rate of 0.8, Depth of Cut (DoC) at 0.4m). The
Sometech SV-35 video microscope system used to quantify of the
tool wear. The result shown that tool life span increasing with the
cutting speeds at (370m/min, feed rate of 0.8mm/tooth and DoC at
0.4mm) which constituted an optimum condition for longer tool life
lasted until 123.2 mins. Meanwhile, at medium cutting speed which
at 300m/m, feed rate of 0.8mm/tooth and depth of cut at 0.4mm we
found that tool life span lasted until 119.86 mins while at low cutting
speed it lasted in 119.66 mins. High cutting speed will give the best
parameter in cutting AlSi/AlN MMCs material. The result will help
manufacturers in machining process of AlSi/AlN MMCs materials.
Abstract: Steganography is the art and science that hides the information in an appropriate cover carrier like image, text, audio and video media. In this work the authors propose a new image based steganographic method for hiding information within the complex bit planes of the image. After slicing into bit planes the cover image is analyzed to extract the most complex planes in decreasing order based on their bit plane complexity. The complexity function next determines the complex noisy blocks of the chosen bit plane and finally pixel mapping method (PMM) has been used to embed secret bits into those regions of the bit plane. The novel approach of using pixel mapping method (PMM) in bit plane domain adaptively embeds data on most complex regions of image, provides high embedding capacity, better imperceptibility and resistance to steganalysis attack.
Abstract: Carbon nanotube is one of the most attractive materials
for the potential applications of nanotechnology due to its excellent
mechanical, thermal, electrical and optical properties. In this paper we
report a supercapacitor made of nickel foil electrodes, coated with
multiwall carbon nanotubes (MWCNTs) thin film using
electrophoretic deposition (EPD) method. Chemical vapor deposition
method was used for the growth of MWCNTs and ethanol was used as
a hydrocarbon source. High graphitic multiwall carbon nanotube was
found at 750oC analyzing by Raman spectroscopy. We observed the
electrochemical performance of supercapacitor by cyclic
voltammetry. The electrodes of supercapacitor fabricated from
MWCNTs exhibit considerably small equivalent series resistance
(ESR), and a high specific power density. Electrophoretic deposition
is an easy method in fabricating MWCNT electrodes for high
performance supercapacitor.
Abstract: Two types of glass fibers having different lengths
(1/16" and 1/32") were added into rigid PVC foams to enhance the
dimensional stability of extruded rigid Polyvinyl Chloride (PVC)
foam at different concentrations (0-20 phr) using a single screw
profile extruder. PVC foam-glass fiber composites (PVC-GF) were
characterized for their dimensional stability, structural, thermal, and
mechanical properties. Experimental results show that the
dimensional stability, heat resistance, and storage modulus were
enhanced without compromising the tensile and flexural strengths of
the composites. Overall, foam composites which were prepared with
longer glass fibers exhibit better mechanical and thermal properties
than those prepared with shorter glass fibers due to higher
interlocking between the fibers and the foam cells, which result in
better load distribution in the matrix.
Abstract: Regardless of the manufacturing process used,
subtractive or additive, material, purpose and application, produced
components are conventionally solid mass with more or less complex
shape depending on the production technology selected. Aspects
such as reducing the weight of components, associated with the low
volume of material required and the almost non-existent material
waste, speed and flexibility of production and, primarily, a high
mechanical strength combined with high structural performance, are
competitive advantages in any industrial sector, from automotive,
molds, aviation, aerospace, construction, pharmaceuticals, medicine
and more recently in human tissue engineering. Such features,
properties and functionalities are attained in metal components
produced using the additive technique of Rapid Prototyping from
metal powders commonly known as Selective Laser Melting (SLM),
with optimized internal topologies and varying densities. In order to
produce components with high strength and high structural and
functional performance, regardless of the type of application, three
different internal topologies were developed and analyzed using
numerical computational tools. The developed topologies were
numerically submitted to mechanical compression and four point
bending testing. Finite Element Analysis results demonstrate how
different internal topologies can contribute to improve mechanical
properties, even with a high degree of porosity relatively to fully
dense components. Results are very promising not only from the
point of view of mechanical resistance, but especially through the
achievement of considerable variation in density without loss of
structural and functional high performance.
Abstract: Particles are the most common and cheapest
reinforcement producing discontinuous reinforced composites with
isotropic properties. Conventional fabrication methods can be used to
produce a wide range of product forms, making them relatively
inexpensive. Optimising composite development must include
consideration of all the fundamental aspect of particles including
their size, shape, volume fraction, distribution and mechanical
properties. Research has shown that the challenges of low fracture
toughness, poor crack growth resistance and low thermal stability can
be overcome by reinforcement with particles. The unique properties
exhibited by micro particles reinforced ceramic composites have
made them to be highly attractive in a vast array of applications.
Abstract: This paper illustrates the effect of nano Magnesium
Hydroxide (MH) loading on the thermal properties of Low Density
Polyethylene (LDPE)/Poly (ethylene-co vinyl acetate) (EVA) nano
composite. Thermal studies were conducted, as it understanding is
vital for preliminary development of new polymeric systems.
Thermal analysis of nanocomposite was conducted using thermo
gravimetric analysis (TGA), and differential scanning calorimetry
(DSC). Major finding of TGA indicated two main stages of
degradation process found at (350 ± 25oC) and (480 ± 25oC)
respectively. Nano metal filler expressed better fire resistance as it
stand over high degree of temperature. Furthermore, DSC analysis
provided a stable glass temperature around 51 (±1oC) and captured
double melting point at 84 (±2oC) and 108 (±2oC). This binary
melting point reflects the modification of nano filler to the polymer
matrix forming melting crystals of folded and extended chain. The
percent crystallinity of the samples grew vividly with increasing filler
content. Overall, increasing the filler loading improved the
degradation temperature and weight loss evidently and a better
process and phase stability was captured in DSC.
Abstract: Dissimilar joining of Titanium and Aluminum thin
sheets has potential applications in aerospace and automobile
industry which can reduce weight and cost and improve strength,
corrosion resistance and high temperature properties. However
successful welding of Titanium/Aluminium sheets is of challenge due
to differences in physical, chemical and metallurgical properties
between the two. This paper describes research results of Laser Beam
Welding (LBW) of Ti/Al thin sheets in which many researchers have
recently performed and critically reviewed from different
perspectives. Also some of notable works in the field of laser welding
with changes in mechanical properties, crack propagation, diffusion
behavior, chemical potential, interfacial reaction and the
microstructure are reported.
Abstract: The hydrogenated amorphous carbon films (α-C:H)
were deposited on p-type Si (100) substrates at different thicknesses by
radio frequency plasma enhanced chemical vapor deposition
technique (rf-PECVD). Raman spectra display asymmetric
diamond-like carbon (DLC) peaks, representative of the α-C:H films.
The decrease of intensity ID/IG ratios revealed the sp3 content arise at
different thicknesses of the α-C:H films. In terms of mechanical
properties, the high hardness and elastic modulus values showed the
elastic and plastic deformation behaviors related to sp3 content in
amorphous carbon films. Electrochemical properties showed that the
α-C:H films exhibited excellent corrosion resistance in air-saturated
3.5 wt.% NaCl solution for pH 2 at room temperature. Thickness
increasing affected the small sp2 clusters in matrix, restricting the
velocity transfer and exchange of electrons. The deposited α-C:H films
exhibited excellent mechanical properties and corrosion resistance.
Abstract: Musculoskeletal injuries in school children could be
reduced improving trunk strength and hamstring flexibility. Low
levels of trunk muscle strength and hamstring flexibility may result in
acute and musculoskeletal chronic diseases. The Pilates Method can
be appropriate to improve these physical condition attributes and has
been rarely employed by this social group. On the other hand, it has
been shown that trunk strength and flexibility are different between
genders, but there is no evidence about the effect of exercise
programs designed to improve both items in school children.
Therefore the objective of this study was to measure the effect of a
six-week Pilates-based exercise program in 14 year old school
children trunk strength and hamstring flexibility, establishing
differences in gender. The sample was composed of 57 students
divided into experimental group (EG; n=30) and control group (CG;
n=27). Bench Trunk Curl test (BTC), Sörensen test and Toe-touch
test (TT) were used to measure dynamic muscular resistance in trunk
flexion, isometric strength in trunk extension and hamstring
flexibility, respectively. EG utilized the Pilates exercise program
during six-weeks (2 days/week, 55minutes/session). After this period
of training, EG improved trunk strength and hamstring flexibility
significantly but there were no significant differences within CG.
Although boys were better in BTC test and girls were better in TT
test, there were no significant differences between them.