Abstract: Kepsut-Dursunbey volcanic field (KDVF) is located
in NW Turkey and contains various products of the post-collisional
Neogene magmatic activity. Two distinct volcanic suites have been
recognized; the Kepsut volcanic suite (KVS) and the Dursunbey
volcanic suite (DVS). The KVS includes basaltic trachyandesitebasaltic
andesite-andesite lavas and associated pyroclastic rocks. The
DVS consists of dacite-rhyodacite lavas and extensive pumice-ash
fall and flow deposits. Petrographical features (i.e. existence of
xenocrysts, glomerocrysts, and mixing-compatible textures) and
mineral chemistry of phenocryst assemblages of both suites provide
evidence for magma mixing/AFC. Calculated crystallization
pressures and temperatures give values of 5.7–7.0 kbar and 927–982
°C for the KVS and 3.7–5.3 kbar and 783-787°C for the DVS,
indicating separate magma reservoirs and crystallization in magma
chambers at deep and mid crustal levels, respectively. These
observations support the establishment and evolution of KDVF
magma system promoted by episodic basaltic inputs which may
generate and mix with crustal melts.
Abstract: In this study, the effect of nanofluids on the pool film
boiling was experimentally investigated at saturated condition under
atmospheric pressure. For this purpose, four different water-based
nanofluids (Al2O3, SiO2, TiO2 and CuO) with 0.1% particle volume
fraction were prepared. To investigate the boiling heat transfer, a
cylindrical rod with high temperature was used. The rod heated up to
high temperatures was immersed into nanofluids. The center
temperature of rod during the cooling process was recorded by using
a K-type thermocouple. The quenching curves showed that the pool
boiling heat transfer was strongly dependent on the nanoparticle
materials. During the repetitive quenching tests, the cooling time
decreased and thus, the film boiling vanished. Consequently, the
primary reason of this was the change of the surface characteristics
due to the nanoparticles deposition on the rod-s surface.
Abstract: The effect of SnO2 surface modification by Ag nanoclusters, synthesized by SILD method, on the operating characteristics of thin film gas sensors was studied and models for the promotional role of Ag additives were discussed. It was found that mentioned above approach can be used for improvement both the sensitivity and the rate of response of the SnO2-based gas sensors to CO and H2. At the same time, the presence of the Ag clusters on the surface of SnO2 depressed the sensor response to ozone.
Abstract: The purpose of this research is to reduce the amount of incomplete coating of stainless steel washers in the electrodeposition painting process by using an experimental design technique. The surface preparation was found to be a major cause of painted surface quality. The influence of pretreating and painting process parameters, which are cleaning time, chemical concentration and shape of hanger were studied. A 23 factorial design with two replications was performed. The analysis of variance for the designed experiment showed the great influence of cleaning time and shape of hanger. From this study, optimized cleaning time was determined and a newly designed electrical conductive hanger was proved to be superior to the original one. The experimental verification results showed that the amount of incomplete coating defects decreased from 4% to 1.02% and operation cost decreased by 10.5%.
Abstract: Carboneous catalytical methane decomposition is an
attractive process because it produces two valuable products:
hydrogen and carbon. Furthermore, this reaction does not emit any
green house or hazardous gases. In the present study, experiments
were conducted in a thermo gravimetric analyzer using Fluka 05120
as carboneous catalyst to analyze its effectiveness in methane
decomposition. Various temperatures and methane partial pressures
were chosen and carbon mass gain was observed as a function of
time. Results are presented in terms of carbon formation rate,
hydrogen production and catalytical activity. It is observed that there
is linearity in carbon deposition amount by time at lower reaction
temperature (780 °C). On the other hand, it is observed that carbon
and hydrogen formation rates are increased with increasing
temperature. Finally, we observed that the carbon formation rate is
highest at 950 °C within the range of temperatures studied.
Abstract: Internal controls of accounting are an essential
business function for a growth-oriented organization, and include the
elements of risk assessment, information communications and even
employees' roles and responsibilities. Internal controls of accounting
systems are designed to protect a company from fraud, abuse and
inaccurate data recording and help organizations keep track of
essential financial activities. Internal controls of accounting provide a
streamlined solution for organizing all accounting procedures and
ensuring that the accounting cycle is completed consistently and
successfully. Implementing a formal Accounting Procedures Manual
for the organization allows the financial department to facilitate
several processes and maintain rigorous standards. Internal controls
also allow organizations to keep detailed records, manage and
organize important financial transactions and set a high standard for
the organization's financial management structure and protocols. A
well-implemented system also reduces the risk of accounting errors
and abuse. A well-implemented controls system allows a company's
financial managers to regulate and streamline all functions of the
accounting department. Internal controls of accounting can be set up
for every area to track deposits, monitor check handling, keep track
of creditor accounts, and even assess budgets and financial statements
on an ongoing basis. Setting up an effective accounting system to
monitor accounting reports, analyze records and protect sensitive
financial information also can help a company set clear goals and
make accurate projections. Creating efficient accounting processes
allows an organization to set specific policies and protocols on
accounting procedures, and reach its financial objectives on a regular
basis. Internal accounting controls can help keep track of such areas
as cash-receipt recording, payroll management, appropriate recording
of grants and gifts, cash disbursements by authorized personnel, and
the recording of assets. These systems also can take into account any
government regulations and requirements for financial reporting.
Abstract: This paper presents a comparative study on
Vanadyl Phthalocyanine (VOPc) thin films deposited by thermal
evaporation and spin coating techniques. The samples
were prepared on cleaned glass substrates and annealed at
various temperatures ranging form 95oC to 155oC. To obtain
the morphological and structural properties of VOPc thin
films, X-ray diffraction (XRD) technique and atomic force
microscopy (AFM) have been implied. The AFM topographic
images show a very slight difference in the thermally grown
films, before and after annealing, however best results are
achieved for the spin-cast film annealed at 125oC. The XRD
spectra show no existence of the sharp peaks, suggesting the
material to be amorphous. The humps in the XRD patterns
indicate the presence of some crystallites.
Abstract: We fabricated multi-walled carbon nanotube (MCNT)
emitters by an electroporetic deposition (EPD) method using a
MCNT-sodium dodecyl sulfate (SDS) suspension. MCNT films were
prepared on graphite tip using EPD. We observe field emission
properties of MCNT film after heat treatment. Consequently, The
MCNT film on graphite tip exhibit good electron emission current.
Abstract: Vickers indentation is used to measure the hardness
of materials. In this study, numerical simulation of Vickers
indentation experiment was performed for Diamond like Carbon
(DLC) coated materials. DLC coatings were deposited on stainless
steel 304 substrates with Chromium buffer layer using RF Magnetron
and T-shape Filtered Cathodic Vacuum Arc Dual system The
objective of this research is to understand the elastic plastic
properties, stress strain distribution, ring and lateral crack growth and
propagation, penetration depth of indenter and delamination of
coating from substrate with effect of buffer layer thickness. The
effect of Poisson-s ratio of DLC coating was also analyzed. Indenter
penetration is more in coated materials with thin buffer layer as
compared to thicker one, under same conditions. Similarly, the
specimens with thinner buffer layer failed quickly due to high
residual stress as compared to the coated materials with reasonable
thickness of 200nm buffer layer. The simulation results suggested the
optimized thickness of 200 nm among the prepared specimens for
durable and long service.
Abstract: TiO2 supported nano-ZnO catalyst was prepared by
deposition-precipitation and tested for the trans-esterification
reaction of soybean oil to biodiesel. The TiO2 support stabilized the
nano-ZnO in a dispersed form with limited crystallite size compared
to the unsupported ZnO. The final ZnO dispersion and crystallite size
and the material transfer resistance in the catalyst significantly
influenced the supported nano-ZnO catalyst performance.
Abstract: The aim of this study was to synthesize the single
walled carbon nanotubes (SWCNTs) and determine their hydrogen
storage capacities. SWCNTs were firstly synthesized by chemical
vapor deposition (CVD) of acetylene (C2H2) on a magnesium oxide
(MgO) powder impregnated with an iron nitrate (Fe(NO3)3·9H2O)
solution. The synthesis parameters were selected as: the synthesis
temperature of 800°C, the iron content in the precursor of 5% and the
synthesis time of 30 min. Purification process of SWCNTs was
fulfilled by microwave digestion at three different temperatures (120,
150 and 200 °C), three different acid concentrations (0.5, 1 and 1.5
M) and for three different time intervals (15, 30 and 60 min). Nitric
acid (HNO3) was used in the removal of the metal catalysts. The
hydrogen storage capacities of the purified materials were measured
using volumetric method at the liquid nitrogen temperature and gas
pressure up to 100 bar. The effects of the purification conditions such
as temperature, time and acid concentration on hydrogen adsorption
were investigated.
Abstract: In this study, the conversion of n-pentane to aromatics is investigated on HZSM-5 zeolites modified by Ga ion-exchange and silylation using tetraethyl orthosilicate (TEOS) via chemical liquid deposition (CLD). The effect of SiO2/Al2O3 ratios of HZSM-5 was also studied. Parameters in preparing catalysts i.e. TEOS loading and cycles of deposition were varied to obtain the optimal condition for enhancing p-xylene selectivity. The highest p-xylene selectivity 99.7% was achieved when the amount of TEOS was 20 vol.%.The catalysts were characterized by TPD, TPO, XRF, and BET. Results show that the conversion of n-pentane was influenced remarkably by the SiO2/Al2O3 ratios of HZSM-5. The highest p-xylene selectivity 99.7% was achieved when the amount of TEOS was 20 vol.%. And cycles of deposition greatly improves HZSM-5 shape-selectivity.
Abstract: Sol-gel method has been used to fabricate
nanocomposite films on glass substrates composed halloysite clay
mineral and nanocrystalline TiO2. The methodology for the synthesis
involves a simple chemistry method utilized nonionic surfactant
molecule as pore directing agent along with the acetic acid-based solgel
route with the absence of water molecules. The thermal treatment
of composite films at 450oC ensures elimination of organic material
and lead to the formation of TiO2 nanoparticles onto the surface of
the halloysite nanotubes. Microscopy techniques and porosimetry
methods used in order to delineate the structural characteristics of the
materials. The nanocomposite films produced have no cracks and
active anatase crystal phase with small crystallite size were deposited
on halloysite nanotubes. The photocatalytic properties for the new
materials were examined for the decomposition of the Basic Blue 41
azo dye in solution. These, nanotechnology based composite films
show high efficiency for dye’s discoloration in spite of different
halloysite quantities and small amount of halloysite/TiO2 catalyst
immobilized onto glass substrates. Moreover, we examined the
modification of the halloysite/TiO2 films with silver particles in order
to improve the photocatalytic properties of the films. Indeed, the
presence of silver nanoparticles enhances the discoloration rate of the
Basic Blue 41 compared to the efficiencies obtained for unmodified
films.
Abstract: This article discusses the questions concerning of creating small packet networks for energy companies with application of high voltage power line carrier equipment (PLC) with functionality of IP traffic transmission. The main idea is to create converged PLC links between substations and dispatching centers where packet data and voice are transmitted in one data flow. The article contents description of basic conception of the network, evaluation of voice traffic transmission parameters, and discussion of header compression techniques in relation to PLC links. The results of exploration show us, that convergent packet PLC links can be very useful in the construction of small packet networks between substations in remote locations, such as deposits or low populated areas.
Abstract: Paper presents knowledge about types of test in area
of materials properties of selected methods of rapid prototyping
technologies. In today used rapid prototyping technologies for
production of models and final parts are used materials in initial state
as solid, liquid or powder material structure. In solid state are used
various forms such as pellets, wire or laminates. Basic range
materials include paper, nylon, wax, resins, metals and ceramics. In
Fused Deposition Modeling (FDM) rapid prototyping technology are
mainly used as basic materials ABS (Acrylonitrile Butadiene
Styrene), polyamide, polycarbonate, polyethylene and polypropylene.
For advanced FDM applications are used special materials as silicon
nitrate, PZT (Piezoceramic Material - Lead Zirconate Titanate),
aluminium oxide, hydroxypatite and stainless steel.
Abstract: The modified Claus process is commonly used in oil
refining and gas processing to recover sulfur and destroy
contaminants formed in upstream processing. A Claus furnace feed
containing a relatively low concentration of H2S may be incapable of
producing a stable flame. Also, incomplete combustion of
hydrocarbons in the feed can lead to deterioration of the catalyst in
the reactors due to soot or carbon deposition. Therefore, special
consideration is necessary to achieve the appropriate overall sulfur
recovery. In this paper, some configurations available to treat lean
acid gas streams are described and the most appropriate ones are
studied to overcome low H2S concentration problems. As a result,
overall sulfur recovery is investigated for feed preheating and hot gas
configurations.
Abstract: Analysis of blood vessel mechanics in normal and
diseased conditions is essential for disease research, medical device
design and treatment planning. In this work, 3D finite element
models of normal vessel and atherosclerotic vessel with 50% plaque
deposition were developed. The developed models were meshed
using finite number of tetrahedral elements. The developed models
were simulated using actual blood pressure signals. Based on the
transient analysis performed on the developed models, the parameters
such as total displacement, strain energy density and entropy per unit
volume were obtained. Further, the obtained parameters were used to
develop artificial neural network models for analyzing normal and
atherosclerotic blood vessels. In this paper, the objectives of the
study, methodology and significant observations are presented.
Abstract: The aim of this article is to assess the existing
business models used by the banks operating in the CEE countries in
the time period from 2006 till 2011.
In order to obtain research results, the authors performed
qualitative analysis of the scientific literature on bank business
models, which have been grouped into clusters that consist of such
components as: 1) capital and reserves; 2) assets; 3) deposits, and 4)
loans.
In their turn, bank business models have been developed based on
the types of core activities of the banks, and have been divided into
four groups: Wholesale, Investment, Retail and Universal Banks.
Descriptive statistics have been used to analyse the models,
determining mean, minimal and maximal values of constituent
cluster components, as well as standard deviation. The analysis of
the data is based on such bank variable indices as Return on Assets
(ROA) and Return on Equity (ROE).
Abstract: Unlike its conventional counterpart, Islamic principles
forbid Islamic banks to take any interest-related income and thus
makes deposits from depositors as an important source of fund for its
operational and financing. Consequently, the risk of deposit
withdrawal by depositors is an important aspect that should be wellmanaged
in Islamic banking. This paper aims to investigate factors
that influence depositors- withdrawal behavior in Islamic banks,
particularly in Malaysia, using the framework of theory of reasoned
action. A total of 368 respondents from Klang valley are involved in
the analysis. The paper finds that all the constructs variable i.e.
normative beliefs, subjective norms, behavioral beliefs, and attitude
towards behavior are perceived to be distinct by the respondents. In
addition, the structural equation model is able to verify the structural
relationships between subjective norms, attitude towards behavior
and behavioral intention. Subjective norms gives more influence to
depositors- decision on deposit withdrawal compared to attitude
towards behavior.
Abstract: An attempt has been made to determine the strength
and impact properties of Cr-Mo steel weld and base materials by
varying the current during manual metal arc welding. Toughness over
a temperature range from -32 to 100°C of base, heat affected zone
(HAZ) and weld zones at three current settings are made. It is
observed that the deterioration in notch toughness at any zone with
the temperature decreases. The values of notch toughness for all
zones at -32°C are almost same for any current settings. The values
of notch toughness at HAZ area are higher than that of weld area due
to the coarsening of ferrite grain of HAZ occurs with higher heat
input. From microhardness and microstructure result, it can be
concluded that large inclusion content in weld deposit is the cause of
lower notch toughness value.