Abstract: In this study, the theoretical relationship between pressure and density was investigated on cylindrical hollow fuel briquettes produced of a mixture of fibrous biomass material using a screw press without any chemical binder. The fuel briquettes were made of biomass and other waste material such as spent coffee beans, mielie husks, saw dust and coal fines under pressures of 0.878-2.2 Mega Pascals (MPa). The material was densified into briquettes of outer diameter of 100mm, inner diameter of 35mm and 50mm long. It was observed that manual screw compression action produces briquettes of relatively low density as compared to the ones made using hydraulic compression action. The pressure and density relationship was obtained in the form of power law and compare well with other cylindrical solid briquettes made using hydraulic compression action. The produced briquettes have a dry density of 989 kg/m3 and contain 26.30% fixed carbon, 39.34% volatile matter, 10.9% moisture and 10.46% ash as per dry proximate analysis. The bomb calorimeter tests have shown the briquettes yielding a gross calorific value of 18.9MJ/kg.
Abstract: This article summarizes ways to verify neutron
fluence for neutron transmutation doping of silicon with phosphorus
on the LVR-15 reactor. Neutron fluence is determined using
activation detectors placed along the crystal in a strip or encapsulated
in a rod holder. Holders are placed at the centre of a water-filled
capsule or in an aluminum or silicon ingot that simulates a real single
crystal. If the diameter of the crystal is significantly less than the
capsule diameter and water from the primary circuit enters the free
space in the capsule, neutron interaction in the water changes neutron
fluence, affecting axial irradiation homogeneity. The effect of
moving the capsule vertically in the channel relative to maximum
neutron fluence in the reactor core was also measured. Even a small
shift of the capsule-s centre causes great irradiation inhomogeneity.
This effect was measured using activation detectors, and was also
confirmed by MCNP calculation.
Abstract: The LHP is a two-phase device with extremely high
effective thermal conductivity that utilizes the thermodynamic
pressure difference to circulate a cooling fluid. A thermodynamics
analytical model is developed to explore different parameters effects
on a Loop Heat Pipe (LHP).. The effects of pipe length, pipe
diameter, condenser temperature, and heat load are reported. As pipe
length increases and/or pipe diameter decreases, a higher temperature
is expected in the evaporator.
Abstract: The separation efficiency of a hydrocyclone has
extensively been considered on the rigid particle assumption. A
collection of experimental studies have demonstrated their
discrepancies from the modeling and simulation results. These
discrepancies caused by the actual particle elasticity have generally
led to a larger amount of energy consumption in the separation
process. In this paper, the influence of particle elasticity on the
separation efficiency of a hydrocyclone system was investigated
through the Finite Element (FE) simulations using crude oil droplets
as the elastic particles. A Reitema-s design hydrocyclone with a
diameter of 8 mm was employed to investigate the separation
mechanism of the crude oil droplets from water. The cut-size
diameter eter of the crude oil was 10 - Ðçm in order to fit with the
operating range of the adopted hydrocylone model. Typical
parameters influencing the performance of hydrocyclone were varied
with the feed pressure in the range of 0.3 - 0.6 MPa and feed
concentration between 0.05 – 0.1 w%. In the simulation, the Finite
Element scheme was applied to investigate the particle-flow
interaction occurred in the crude oil system during the process. The
interaction of a single oil droplet at the size of 10 - Ðçm to the flow
field was observed. The feed concentration fell in the dilute flow
regime so the particle-particle interaction was ignored in the study.
The results exhibited the higher power requirement for the separation
of the elastic particulate system when compared with the rigid
particulate system.
Abstract: A solar powered air heating system using one ended evacuated tubes is experimentally investigated. A solar air heater containing forty evacuated tubes is used for heating purpose. The collector surface area is about 4.44 m2. The length and outer diameters of the outer glass tube and absorber tube are 1500, 47 and 37 mm, respectively. In this experimental setup, we have a header (heat exchanger) of square shape (190 mm x 190 mm). The length of header is 1500 mm. The header consists of a hollow pipe in the center whose diameter is 60 mm through which the air is made to flow. The experimental setup contains approximately 108 liters of water. Water is working as heat collecting medium which collects the solar heat falling on the tubes. This heat is delivered to the air flowing through the header pipe. This heat flow is due to natural convection and conduction. The outlet air temperature depends upon several factors along with air flow rate and solar radiation intensity. The study has been done for both up-flow and down-flow of air in header in similar weather conditions, at different flow rates. In the present investigations the study has been made to find the effect of intensity of solar radiations and flow rate of air on the out let temperature of the air with time and which flow is more efficient. The obtained results show that the system is highly effective for the heating in this region. Moreover, it has been observed that system is highly efficient for the particular flow rate of air. It was also observed that downflow configuration is more effective than up-flow condition at all flow rates due to lesser losses in down-flow. The results show that temperature differences of upper head and lower head, both of water and surface of pipes on the respective ends is lower in down-flow.
Abstract: TTV is an unenveloped circular single-stranded DNA
virus with a diameter of 30-32 nm that first was described in 1997 in
Japan. TTV was detected in various populations without proven
pathology, including blood donors and in patients with chronic HBV
and HCV hepatitis. The aim of this study was to determine the
prevalence of TTV DNA in Iranian patients with chronic hepatitis B
and C. Viral TTV-DNA was studied in 442 samples (202 with HBV,
138 with HCV and 102 controls) collected from west south of Iran.
All extracted serum DNA was amplified by TTV ORF1 gene specific
primers using the semi nested PCR technique. TTV DNA was
detected in the serum of 8.9% and 10.8% patients with chronic
hepatitis B and C, respectively. Prevalence of TTV-DNA in the serum
of 102 controls was 2.9%. Results showed significant relation of TTV
with HBV and HCV in patients by using T test examination (P
Abstract: Due to adverse pressure gradient along the diverging
walls of wide-angled diffusers, the attached flow separates from
one wall and remains attached permanently to the other wall in a
process called stalling. Stalled diffusers render the whole fluid flow
system, in which they are part of, very inefficient. There is then an
engineering need to try to understand the whole process of diffuser
stall if any meaningful attempts to improve on diffuser efficiency
are to be made. In this regard, this paper provides a data bank
contribution for the mean flow-field in wide-angled diffusers where
the complete velocity and static pressure fields, and pressure recovery
data for diffusers in the fully stalled flow regime are experimentally
measured. The measurements were carried out at Reynolds numbers
between 1.07×105 and 2.14×105 based on inlet hydraulic diameter
and centreline velocity for diffusers whose divergence angles were
between 30Ôùª and 50Ôùª. Variation of Reynolds number did not significantly
affect the velocity and static pressure profiles. The wall static
pressure recovery was found to be more sensitive to changes in the
Reynolds number. By increasing the velocity from 10 m/s to 20 m/s,
the wall static pressure recovery increased by 8.31%. However, as the
divergence angle was increased, a similar increase in the Reynolds
number resulted in a higher percentage increase in pressure recovery.
Experimental results showed that regardless of the wall to which
the flow was attached, both the velocity and pressure fields were
replicated with discrepancies below 2%.
Abstract: In this study, ZnO nano rods and ZnO ultrafine particles were synthesized by Gel-casting method. The synthesized ZnO powder has a hexagonal zincite structure. The ZnO aggregates with rod-like morphology are typically 1.4 μm in length and 120 nm in diameter, which consist of many small nanocrystals with diameters of 10 nm. Longer wires connected by many hexahedral ZnO nanocrystals were obtained after calcinations at the temperature over 600° C.The crystalline structures and morphologies of the powder have been characterized by X-ray diffraction(XRD) and Scaning electron microscopy (SEM).The result shows that the different preparation conditions such as concentration H2O, calcinations time and calcinations temperature have a lot of influences upon the properties of nano ZnO powders, an increase in the temperature of the calcinations results in an increase of the grain size and also the increase of the calcinations time in high temperature makes the size of the grains bigger. The existences of extra watter prevent nano grains from improving like rod morphology. We have obtained the smallest grain size of ZnO powder by controlling the process conditions. Finally In a suitable condition, a novel nanostructure, namely bi-rod-like ZnO nano rods was found which is different from known ZnO nanostructures.
Abstract: The main objective of this study was to determine the effects
of vermicompost and amino acids on the qualitative and quantitative yield of
chamomile. The experiment was conducted during the growing season of
2010 at the Alborz Medical Research Center. The Treatment groups consisted
of vermicompost (0, 5, 10, 15 and 20 tons/ha) and the sprays of amino acids
(budding stag, flowering stage, and budding + flowering stage). The
experimental design was a factorial experiment based on Randomized
Complete Block Design (RCBD) with three replications. The present results
have shown that the highest plant height, flower head diameter, fresh and dry
flower yield and significant essential oil content were obtained by using 20-
ton vermicompost per hectare. Effects of amino acids were similar to those
seen in vermicompost treatment and all measured traits were seen to be
significant after the spray of amino acids at the budding + flowering stage).
Abstract: In this experimental study, performance of a counter
flow Ranque-Hilsch vortex tube (RHVT) with threads cut on its inner
surface was investigated experimentally (pitch is 1 and 2 mm). The
inner diameter of the vortex tube used was D=9 mm and the ratio of
the tube’s length to diameter was L/D=12. The experimental system
was a thermodynamic open system. Flow was controlled by a valve
on the hot outlet side, where the valve was changed from a nearly
closed position to its nearly open position. Fraction of cold flow (ξ) =
0.1-0.9, was determined under 300 and 350 kPa pressurized air. All
experimental data were compared with each other, the maximum
heating performance of the RHVT system was found to be 38.2 oC
and the maximum cooling performance of the RHVT in this study
was found to be -30.9 oC at pitch 1 mm.
Abstract: The carbon based coils with the nanometer scale have
the 3 dimension helix geometry. We synthesized the carbon nano-coils
by the use of chemical vapor deposition technique with iron and tin as
the catalysts. The fabricated coils have the external diameter of
ranging few hundred nm to few thousand nm. The Scanning
Electro-Microscope (SEM) and Tunneling Electro-Microscope has
shown detail images of the coil-s structure. The fabrication of the
carbon nano-coils can be grown on the metal and non-metal substrates,
such as the stainless steel and silicon substrates. Besides growth on the
flat substrate; they also can be grown on the stainless steel wires. After
the synthesis of the coils, the mechanical and electro-mechanical
property is measured. The experimental results were reported.
Abstract: A pot experiment was carried out under controlled
conditions to evaluate the residual effects of different doses of
atrazine+alachlor and foramsulfuron used in corn fields on the
growth and physiology of rapeseed (Brassica napus L.). A split-plot
experiment in CRD with 4 replications was used. The main plots
consisted of herbicide type (atrazine+alachlor mixture and
foramsulfuron) and the sub-plots were different residual doses of the
herbicides (0, 1%, 5%, 10%, 20%, 40%, 50% and 100%). 7 cm
diameter pots were filled with a virgin soil and seeds of rapeseed cv.
Hayola were planted in them. The pots were kept under controlled
conditions for 8 weeks after germination. At harvest, the growth
parameters and the chlorophyll contents of the leaves were
determined. The results showed that the growth of rapeseed plants
was completely prevented at the highest residual doses of the
herbicides (50 and 100 %). The growth parameters of rapeseed plants
were affected by all doses of both types of the herbicide as compared
to the controls. The residual effects of atrazine+alachlor mixture in
reducing the growth parameters of rapeseed were more pronounced
as compared to the residual effects of foramsulfuron alone.
Abstract: It is well known that the abrasive particles in the
abrasive water suspension has significant effect on the erosion
characteristics of the inside surface of the nozzle. Abrasive particles
moving with the flow cause severe skin friction effect, there by
altering the nozzle diameter due to wear which in turn reflects on the
life of the nozzle for effective machining. Various commercial
abrasives are available for abrasive water jet machining. The erosion
characteristic of each abrasive is different. In consideration of this
aspect, in the present work, the effect of abrasive materials namely
garnet, aluminum oxide and silicon carbide on skin friction
coefficient due to wall shear stress and jet kinetic energy has been
analyzed. It is found that the abrasive material of lower density
produces a relatively higher skin friction effect and higher jet exit
kinetic energy.
Abstract: Numerous experimental tests for post-installed anchor systems drilled in hardened concrete were conducted in order to estimate pull-out and shear strength accounting for uncertainties such as torque ratios, embedment depths and different diameters in demands. In this study, the strength of the systems was significantly changed by the effect of those three uncertainties during pull-out experimental tests, whereas the shear strength of the systems was not affected by torque ratios. It was also shown that concrete cone failure or damage mechanism was generally investigated during and after pull-out tests and in shear strength tests, mostly the anchor systems were failed prior to failure of primary structural system. Furthermore, 3D finite element model for the anchor systems was created by ABAQUS for the numerical analysis. The verification of finite element model was identical till the failure points to the load-displacement relationship specified by the experimental tests.
Abstract: Corrugated wire mesh laminates (CWML) are a class
of engineered open cell structures that have potential for applications
in many areas including aerospace and biomedical engineering. Two
different methods of fabricating corrugated wire mesh laminates from
stainless steel, one using a high temperature Lithobraze alloy and the
other using a low temperature Eutectic solder for joining the
corrugated wire meshes are described herein. Their implementation is
demonstrated by manufacturing CWML samples of 304 and 316
stainless steel (SST). It is seen that due to the facility of employing
wire meshes of different densities and wire diameters, it is possible to
create CWML laminates with a wide range of effective densities. The
fabricated laminates are tested under uniaxial compression. The
variation of the compressive yield strength with relative density of the
CWML is compared to the theory developed by Gibson and Ashby for
open cell structures [22]. It is shown that the compressive strength of
the corrugated wire mesh laminates can be described using the same
equations by using an appropriate value for the linear coefficient in the
Gibson-Ashby model.
Abstract: With the aim of improving nutritional profile and antioxidant capacity of gluten-free cookies, blueberry pomace, by-product of juice production, was processed into a new food ingredient by drying and grinding and used for a gluten-free cookie formulation. Since the quality of a baked product is highly influenced by the baking conditions, the objective of this work was to optimize the baking time and thickness of dough pieces, by applying Response Surface Methodology (RSM) in order to obtain the best technological quality of the cookies. The experiments were carried out according to a Central Composite Design (CCD) by selecting the dough thickness and baking time as independent variables, while hardness, color parameters (L*, a* and b* values), water activity, diameter and short/long ratio were response variables. According to the results of RSM analysis, the baking time of 13.74min and dough thickness of 4.08mm was found to be the optimal for the baking temperature of 170°C. As similar optimal parameters were obtained by previously conducted experiment based on sensory analysis, response surface methodology (RSM) can be considered as a suitable approach to optimize the baking process.
Abstract: This paper presents a vertical silicon nanowire n- MOSFET integrated with a CMOS-compatible fully-silicided (FUSI) NiSi2 gate. Devices with nanowire diameter of 50nm show good electrical performance (SS < 70mV/dec, DIBL < 30mV/V, Ion/Ioff > 107). Most significantly, threshold voltage tunability of about 0.2V is shown. Although threshold voltage remains low for the 50nm diameter device, it is expected to become more positive as nanowire diameter reduces.
Abstract: Design of a constant chord propeller is presented in
this paper in order to reduce propeller-s design procedure-s costs. The
design process was based on Lock and Goldstein-s techniques of
propeller design and analysis. In order to calculate optimum chord of
propeller, chord of a referential element is generalized as whole
blades chord. The design outcome which named CS-X-1 is modeled
& analyzed by CFD methods using K-ε: R.N.G turbulence model.
Convergence of results of two codes proved that outcome results of
design process are reliable. Design result is a two-blade propeller
with a total diameter of 1.1 meter, radial velocity of 3000 R.P.M,
efficiency above .75 and power coefficient near 1.05.
Abstract: Single crystals of Magnesium alloys such as Mg-1Al,
Mg-1Zn-0.5Y, Mg-3Li, and AZ31 alloys were successfully fabricated in this study by employing the modified Bridgman method. Single
crystals of pure Mg were also made in this study. To determine the exact orientation of crystals, Laue back-reflection method and pole figure measurement were carried out on each single crystal. Dimensions of single crystals were 10 mm in diameter and 120 mm in
length. Hardness and compression tests were conducted and the results
revealed that hardness and the strength strongly depended on the
orientation. The closer to basal one the orientation was, the higher hardness and compressive strength were. The effect of alloying was
not higher than that of orientation. After compressive deformation of single crystals, the orientation of the crystals was found to rotate and to be parallel to the basal orientation.
Abstract: Our objectives were to evaluate the effects of sire
breed, type of protein supplement, level of supplementation and sex
on wool spinning fineness (SF), its correlations with other wool
characteristics and prediction accuracy in F1 Merino crossbred lambs.
Texel, Coopworth, White Suffolk, East Friesian and Dorset rams
were mated with 500 purebred Merino dams at a ratio of 1:100 in
separate paddocks within a single management system. The F1
progeny were raised on ryegrass pasture until weaning, before forty
lambs were randomly allocated to treatments in a 5 x 2 x 2 x 2
factorial experimental design representing 5 sire breeds, 2
supplementary feeds (canola or lupins), 2 levels of supplementation
(1% or 2% of liveweight) and sex (wethers or ewes). Lambs were
supplemented for six weeks after an initial three weeks of adjustment,
wool sampled at the commencement and conclusion of the feeding
trial and analyzed for SF, mean fibre diameter (FD), coefficient of
variation (CV), standard deviation, comfort factor (CF), fibre
curvature (CURV), and clean fleece yield. Data were analyzed using
mixed linear model procedures with sire fitted as a random effect,
and sire breed, sex, supplementary feed type, level of
supplementation and their second-order interactions as fixed effects.
Sire breed (P