Abstract: Pressure waves and Water Hammer occur in a
pumping system when valves are closed or opened suddenly or in
the case of sudden failure of pumps. Determination of maximum
water hammer is considered one of the most important technical
and economical items of which engineers and designers of
pumping stations and conveyance pipelines should take care.
Hammer Software is a recent application used to simulate water
hammer. The present study focuses on determining significance of
each input parameter of the application relative to the maximum
amount of water hammer estimated by the software. The study
determines estimated maximum water hammer variations due to
variations of input parameters including water temperature, pipe
type, thickness and diameter, electromotor rpm and power, and
moment of inertia of electromotor and pump. In our study,
Kuhrang Pumping Station was modeled using WaterGEMS
Software. The pumping station is characterized by total discharge
of 200 liters per second, dynamic height of 194 meters and 1.5
kilometers of steel conveyance pipeline and transports water to
Cheshme Morvarid for farmland irrigation. The model was run in
steady hydraulic condition and transferred to Hammer Software.
Then, the model was run in several unsteady hydraulic conditions
and sensitivity of maximum water hammer to each input parameter
was calculated. It is shown that parameters to which maximum
water hammer is most sensitive are moment of inertia of pump and
electromotor, diameter, type and thickness of pipe and water
temperature, respectively.
Abstract: We integrate TiN/Ni/HfO2/Si RRAM cell with a
vertical gate-all-around (GAA) nanowire transistor to achieve
compact 4F2 footprint in a 1T1R configuration. The tip of the Si
nanowire (source of the transistor) serves as bottom electrode of the
memory cell. Fabricated devices with nanowire diameter ~ 50nm
demonstrate ultra-low current/power switching; unipolar switching
with 10μA/30μW SET and 20μA/30μW RESET and bipolar switching
with 20nA/85nW SET and 0.2nA/0.7nW RESET. Further, the
switching current is found to scale with nanowire diameter making the
architecture promising for future scaling.
Abstract: This paper details a new concept of using compressed air as a potential zero pollution power source for motorbikes. In place of an internal combustion engine, the motorbike is equipped with an air turbine transforms the energy of the compressed air into shaft work. The mathematical modeling and performance evaluation of a small capacity compressed air driven vaned type novel air turbine is presented in this paper. The effect of isobaric admission and adiabatic expansion of high pressure air for different rotor diameters, casing diameters and ratio of rotor to casing diameters of the turbine have been considered and analyzed. It is concluded that the work output is found optimum for some typical values of rotor / casing diameter ratios. In this study, the maximum power works out to 3.825 kW (5.20 HP) for casing diameter of 200 mm and rotor to casing diameter ratio of 0.65 to 0.60 which is sufficient to run motorbike.
Abstract: We investigated a modified thermal evaporation
method in the growth process of ZnO nanowires. ZnO nanowires
were fabricated on p-type silicon substrates without using a metal
catalyst. A simple horizontal double-tube system along with
chemical vapor diffusion of the precursor was used to grow the ZnO
nanowires. The substrates were placed in different temperature
zones, and ZnO nanowires with different diameters were obtained for
the different substrate temperatures. In addition to the nanowires,
ZnO microdiscs with different diameters were obtained on another
substrate, which was placed at a lower temperature than the other
substrates. The optical properties and crystalline quality of the ZnO
nanowires and microdiscs were characterized by room temperature
photoluminescence (PL) and Raman spectrometers. The PL and
Raman studies demonstrated that the ZnO nanowires and microdiscs
grown using such set-up had good crystallinity with excellent optical
properties. Rectifying behavior of ZnO/Si heterostructures was
characterized by a simple DC circuit.
Abstract: In order to obtaining the dynamic evolution image of Tungsten array for foam padding, and to research the form of interaction between Tungsten plasma and foam column, a shadow imaging system of four-frame ultraviolet probe laser (266nm)has been designed on 1MA pulse power device. The time resolution of the system is 2.5ns, and static space resolution is superior to 70μm. The radial shadowgraphy image reveals the whole process from the melting and expansion of solid wire to the interaction of the precursor plasma and the foam, from the pinch to rebound inflation. The image shows the continuous interaction of Tungsten plasma and foam in a form of “Raining" within a time of about 50ns, the plasma shell structure has not been found in the whole period of pinch. The quantitative analysis indicates the minimum pinching speed of the foam column is 1.0×106cm/s, and maximum pinching speed is 6.0×106cm/s, and the axial stagnation diameter is approx 1mm.
Abstract: The operating control parameters of injection
flushing type of electrical discharge machining process on stainless
steel 304 workpiece with copper tools are being optimized
according to its individual machining characteristic i.e. material
removal rate (MRR). Lower MRR during EDM machining process
may decrease its- machining productivity. Hence, the quality
characteristic for MRR is set to higher-the-better to achieve the
optimum machining productivity. Taguchi method has been used
for the construction, layout and analysis of the experiment for each
of the machining characteristic for the MRR. The use of Taguchi
method in the experiment saves a lot of time and cost of preparing
and machining the experiment samples. Therefore, an L18
Orthogonal array which was the fundamental component in the
statistical design of experiments has been used to plan the
experiments and Analysis of Variance (ANOVA) is used to
determine the optimum machining parameters for this machining
characteristic. The control parameters selected for this
optimization experiments are polarity, pulse on duration, discharge
current, discharge voltage, machining depth, machining diameter
and dielectric liquid pressure. The result had shown that the higher
the discharge voltage, the higher will be the MRR.
Abstract: This paper gives an overview of a deep drawing
process by pressurized liquid medium separated from the sheet by a
rubber diaphragm. Hydroforming deep drawing processing of sheet
metal parts provides a number of advantages over conventional
techniques. It generally increases the depth to diameter ratio possible
in cup drawing and minimizes the thickness variation of the drawn
cup. To explore the deformation mechanism, analytical and
numerical simulations are used for analyzing the drawing process of
an AA6061-T4 blank. The effects of key process parameters such as
coefficient of friction, initial thickness of the blank and radius
between cup wall and flange are investigated analytically and
numerically. The simulated results were in good agreement with the
results of the analytical model. According to finite element
simulations, the hydroforming deep drawing method provides a more
uniform thickness distribution compared to conventional deep
drawing and decreases the risk of tearing during the process.
Abstract: Ground-source heat pumps achieve higher efficiencies
than conventional air-source heat pumps because they exchange heat
with the ground that is cooler in summer and hotter in winter than the
air environment. Earth heat exchangers are essential parts of the
ground-source heat pumps and the accurate prediction of their
performance is of fundamental importance. This paper presents the
development and validation of a numerical model through an
incompressible fluid flow, for the simulation of energy and
temperature changes in and around a U-tube borehole heat
exchanger. The FlexPDE software is used to solve the resulting
simultaneous equations that model the heat exchanger. The validated
model (through a comparison with experimental data) is then used to
extract conclusions on how various parameters like the U-tube
diameter, the variation of the ground thermal conductivity and
specific heat and the borehole filling material affect the temperature
of the fluid.
Abstract: Safety, river environment, and sediment utilization are the elements of the target of sediment management. As a change in an element by sediment management, may affect the other two elements, and the priority among three elements depends on stakeholders. It is necessary to develop a method to evaluate the effect of sediment management on each element and an integrated evaluation method for socio-economic effect. In this study, taking Mount Merapi basin as an investigation field, the method for an active volcanic basin was developed. An integrated evaluation method for sediment management was discussed from a socio-economic point on safety, environment, and sediment utilization and a case study of sediment management was evaluated by means of this method. To evaluate the effect of sediment management, some parameters on safety, utilization, and environment have been introduced. From a utilization point of view, job opportunity, additional income of local people, and tax income to local government were used to evaluate the effectiveness of sediment management. The risk degree of river infrastructure was used to describe the effect of sediment management on a safety aspect. To evaluate the effects of sediment management on environment, the mean diameter of grain size distribution of riverbed surface was used. On the coordinate system designating these elements, the direction of change in basin condition by sediment management can be predicted, so that the most preferable sediment management can be decided. The results indicate that the cases of sediment management tend to give the negative impacts on sediment utilization. However, these sediment managements will give positive impacts on safety and environment condition. Evaluation result from a social-economic point of view shows that the case study of sediment management reduces job opportunity and additional income for inhabitants as well as tax income for government. Therefore, it is necessary to make another policy for creating job opportunity for inhabitants to support these sediment managements.
Abstract: Abrasive waterjet is a novel machining process capable of processing wide range of hard-to-machine materials. This research addresses modeling and optimization of the process parameters for this machining technique. To model the process a set of experimental data has been used to evaluate the effects of various parameter settings in cutting 6063-T6 aluminum alloy. The process variables considered here include nozzle diameter, jet traverse rate, jet pressure and abrasive flow rate. Depth of cut, as one of the most important output characteristics, has been evaluated based on different parameter settings. The Taguchi method and regression modeling are used in order to establish the relationships between input and output parameters. The adequacy of the model is evaluated using analysis of variance (ANOVA) technique. The pairwise effects of process parameters settings on process response outputs are also shown graphically. The proposed model is then embedded into a Simulated Annealing algorithm to optimize the process parameters. The optimization is carried out for any desired values of depth of cut. The objective is to determine proper levels of process parameters in order to obtain a certain level of depth of cut. Computational results demonstrate that the proposed solution procedure is quite effective in solving such multi-variable problems.
Abstract: The purpose of study was to design and construction
the semi-automatic sliced ginger machine for reduce production times
in sheet and slice ginger procedure furthermore, reduced amount of
labor of slides and cutting method. Take consider into clean and safety of workers and consumers. The principle of machines, used 1
horsepower motor, rotation speed of sliced blade 967 rpm, the diameter of sliced dish 310 mm, consists of 2 blades for sheet cutting
ginger and the power from motor which transfer to rotate the sliced blade roller, rotation speed 440 rpm. The slice cutter roller was sliced
ginger from sheet ginger to line ginger. The conveyer could
adjustment level of motors, used to the beginning area that sheet
ginger was transference to the roller for sheet and sliced cutting in next process. The cover of sliced cutting had channel for 1 tuber of
ginger. The semi-automatic sliced ginger machine could produced sheet ginger 81.8 kg/h (6.2 times of labor) and line ginger 17.9 kg/h
(2.5 times of labor) compare with, labor work could produced sheet
ginger 13.2 kg/h and line ginger 7.1 kg/h, and when timekeeper, the
total times of semi auto machine 30.86 kg/h and labor 4.6 kg/h, there
for the semi auto machine was 6.7 times of labor. The semiautomatic
sliced ginger machine convenient, easy for use and
maintain, in addition to reduce fatigue of body and seriousness from
works; must be used high skill, and protection accident in slicing
procedure. Beside, machine could used with other vegetables for
example potato, carrot .etc
Abstract: Bubble columns have a variety of applications in
absorption, bio-reactions, catalytic slurry reactions, and coal
liquefaction; because they are simple to operate, provide good heat
and mass transfer, having less operational cost. The use of
Computational Fluid Dynamics (CFD) for bubble column becomes
important, since it can describe the fluid hydrodynamics on both local
and global scale. Euler- Euler two-phase fluid model has been used to
simulate two-phase (air and water) transient up-flow in bubble
column (15cm diameter) using FLUENT6.3. These simulations and
experiments were operated over a range of superficial gas velocities
in the bubbly flow and churn turbulent regime (1 to16 cm/s) at
ambient conditions. Liquid velocity was varied from 0 to 16cm/s. The
turbulence in the liquid phase is described using the standard k-ε
model. The interactions between the two phases are described
through drag coefficient formulations (Schiller Neumann). The
objectives are to validate CFD simulations with experimental data,
and to obtain grid-independent numerical solutions. Quantitatively
good agreements are obtained between experimental data for hold-up
and simulation values. Axial liquid velocity profiles and gas holdup
profiles were also obtained for the simulation.
Abstract: The tubes in an Ammonia primary reformer furnace
operate close to the limits of materials technology in terms of the
stress induced as a result of very high temperatures, combined with
large differential pressures across the tube wall. Operation at tube
wall temperatures significantly above design can result in a rapid
increase in the number of tube failures, since tube life is very
sensitive to the absolute operating temperature of the tube. Clearly it
is important to measure tube wall temperatures accurately in order to
prevent premature tube failure by overheating.. In the present study,
the catalyst tubes in an Ammonia primary reformer has been modeled
taking into consideration heat, mass and momentum transfer as well
as reformer characteristics.. The investigations concern the effects of
tube characteristics and superficial tube wall temperatures on of the
percentage of heat flux, unconverted methane and production of
Hydrogen for various values of steam to carbon ratios. The results
show the impact of catalyst tubes length and diameters on the
performance of operating parameters in ammonia primary reformers.
Abstract: In recent years, global warming has become a
worldwide problem. The reduction of carbon dioxide emissions is a
top priority for many companies in the manufacturing industry. In the
automobile industry as well, the reduction of carbon dioxide emissions
is one of the most important issues. Technology to reduce the weight
of automotive parts improves the fuel economy of automobiles, and is
an important technology for reducing carbon dioxide. Also, even if
this weight reduction technology is applied to electric automobiles
rather than gasoline automobiles, reducing energy consumption
remains an important issue. Plastic processing of hollow pipes is one
important technology for realizing the weight reduction of automotive
parts. Ohashi et al. [1],[2] present an example of research on pipe
formation in which a process was carried out to enlarge a pipe
diameter using a lost core, achieving the suppression of wall thickness
reduction and greater pipe expansion than hydroforming.
In this study, we investigated a method to increase the wall
thickness of a pipe through pipe compression using planetary rolls.
The establishment of a technology whereby the wall thickness of a
pipe can be controlled without buckling the pipe is an important
technology for the weight reduction of products. Using the finite
element analysis method, we predicted that it would be possible to
increase the compression of an aluminum pipe with a 3mm wall
thickness by approximately 20%, and wall thickness by approximately
20% by pressing the hollow pipe with planetary rolls.
Abstract: Downward turbulent bubbly flows in pipes were
modeled using computational fluid dynamics tools. The
Hydrodynamics, phase distribution and turbulent structure of twophase
air-water flow in a 57.15 mm diameter and 3.06 m length
vertical pipe was modeled by using the 3-D Eulerian-Eulerian
multiphase flow approach. Void fraction, liquid velocity and
turbulent fluctuations profiles were calculated and compared against
experimental data. CFD results are in good agreement with
experimental data.
Abstract: To improve the characterization of blood flows, we propose a method which makes it possible to use the spectral analysis
of the Doppler signals. Our calculation induces a reasonable approximation, the error made on estimated speed reflects the fact
that speed depends on the flow conditions as well as on measurement parameters like the bore and the volume flow rate. The estimate of the Doppler signal frequency enables us to determine the maximum Doppler frequencie Fd max as well as the maximum flow speed. The
results show that the difference between the estimated frequencies
( Fde ) and the Doppler frequencies ( Fd ) is small, this variation tends to zero for important θ angles and it is proportional to the diameter D. The description of the speed of friction and the
coefficient of friction justify the error rate obtained.
Abstract: Nowadays, fluidized bed plays an important part in industry. The design of this kind of reactor requires knowing the interfacial area between two phases and this interfacial area leads to calculate the solid holdup in the bed. Consequently achieving interfacial area between gas and solid in the bed experimentally is so significant. On interfacial area measurement in fluidized bed with gas has been worked, but light transmission technique has been used less. Therefore, in the current research the possibility of using of this technique and its accuracy are investigated. Measuring, a fluidized bed was designed and the problems were averted as far as possible. By using fine solid with equal shape and diameter and installing an optical system, the absorption of light during the time of fluidization has been measured. Results indicate that this method that its validity has been proved in the gas-liquid system, by different reasons have less application in gas-solid system. One important reason could be non-uniformity in such systems.
Abstract: A simple approach is demonstrated for growing large
scale, nearly vertically aligned ZnO nanowire arrays by thermal
oxidation method. To reveal effect of temperature on growth and
physical properties of the ZnO nanowires, gold coated zinc substrates
were annealed at 300 °C and 400 °C for 4 hours duration in air. Xray
diffraction patterns of annealed samples indicated a set of well
defined diffraction peaks, indexed to the wurtzite hexagonal phase of
ZnO. The scanning electron microscopy studies show formation of
ZnO nanowires having length of several microns and average of
diameter less than 500 nm. It is found that the areal density of wires
is relatively higher, when the annealing is carried out at higher
temperature i.e. at 400°C. From the field emission studies, the values
of the turn-on and threshold field, required to draw emission current
density of 10 μA/cm2 and 100 μA/cm2 are observed to be 1.2 V/μm
and 1.7 V/μm for the samples annealed at 300 °C and 2.9 V/μm and
3.7 V/μm for that annealed at 400 °C, respectively. The field
emission current stability, investigated over duration of more than 2
hours at the preset value of 1 μA, is found to be fairly good in both
cases. The simplicity of the synthesis route coupled with the
promising field emission properties offer unprecedented advantage
for the use of ZnO field emitters for high current density
applications.
Abstract: Cylindrical concrete reservoirs are appropriate choice
for storing liquids as water, oil and etc. By using of the pre-cast
concrete reservoirs instead of the in-situ constructed reservoirs, the
speed and precision of the construction would considerably increase.
In this construction method, wall and roof panels would make in
factory with high quality materials and precise controlling. Then,
pre-cast wall and roof panels would carry out to the construction site
for assembling. This method has a few faults such as: the existing
weeks in connection of wall panels together and wall panels to
foundation. Therefore, these have to be resisted under applied loads
such as seismic load. One of the innovative methods which was
successfully applied for seismic retrofitting of numerous pre-cast
cylindrical water reservoirs in New Zealand, using of the high tensile
cables around the reservoirs and post-tensioning them. In this paper,
analytical modeling of wall and roof panels and post-tensioned
cables are carried out with finite element method and the effect of
height to diameter ratio, post-tensioning force value, liquid level in
reservoir, installing position of tendons on seismic response of
reservoirs are investigated.
Abstract: The study aimed to investigate the effect of rice types on chewing behaviours (chewing time, number of chews, and portion size) and bolus properties (bolus moisture content, solid loss, and particle size distribution (PSD)) in human subjects. Five cooked rice types including brown rice (BR), white rice (WR), parboiled white rice (PR), high amylose white rice (HR) and waxy white rice (WXR) were chewed by six subjects. The chewing behaviours were recorded and the food boluses were collected during mastication. Rice typeswere found to significantly influence all chewing parameters evaluated. The WXR and BR showed the most pronounced differences compared with other rice types. The initial moisture content of un-chewed WXR was lowest (43.39%) whereas those of other rice types were ranged from 66.86 to 70.33%. The bolus obtained from chewing the WXR contained lowest moisture content (56.43%) whilst its solid loss (22.03%) was not significant different from those of all rice types. In PSD evaluation using Mastersizer S, the diameter of particles measured was ranged between 4 to 3500 μm. The particle size of food bolus from BR, HR, and WXR contained much finer particles than those of WR and PR.