Abstract: Potassium borates, which are widely used in welding
and metal refining industry, as a lubricating oil additive, cement
additive, fiberglass additive and insulation compound, are one of the
important groups of borate minerals. In this study the production of a
potassium borate mineral via hydrothermal method is aimed. The
potassium source of potassium nitrate (KNO3) was used along with a
sodium source of sodium hydroxide (NaOH) and boron source of
boric acid (H3BO3). The constant parameters of reaction temperature
and reaction time were determined as 80°C and 1 h, respectively. The
molar ratios of 1:1:3 (as KNO3:NaOH:H3BO3), 1:1:4, 1:1:5, 1:1:6
and 1:1:7 were used. Following the synthesis the identifications of
the produced products were conducted by X-Ray Diffraction (XRD),
Fourier Transform Infrared Spectroscopy (FT-IR) and Raman
Spectroscopy. The results of the experiments and analysis showed in
the ratio of 1:1:6, the Santite mineral with powder diffraction file
number (pdf no.) of 01-072-1688, which is known as potassium
pentaborate (KB5O8·4H2O) was synthesized as best.
Abstract: The addition of lime as Ca(OH)2 to sewage sludge to
destroy pathogens (Escherichia coli), was evaluated also in relation
to heavy metal bioavailability.
The obtained results show that the use of calcium hydroxide at the
dose of 3% effectively destroyed pathogens ensuring the stability at
high pH values over long period and the duration of the sewage
sludge stabilization. In general, lime addition decreased the total
extractability of heavy metals indicating a reduced bioavailability of
these elements. This is particularly important for a safe utilization in
agricultural soils to reduce the possible transfer of heavy metals to
the food chain.
Abstract: Froth flotation remains to date as one of the most used
metallurgical processes for concentrating metal-bearing minerals in
ores. Oxide ores are relatively less amenable to froth flotation and
require a judicious choice of reagents for the recovery of metals to be
optimised. Laboratory batch flotation tests were conducted to
determine the effect of two types of gasoil-rinkalore mixtures on the
flotation response of a copper cobalt oxide ore sample. The head
assay conducted on the initial ore sample showed that it contained
about 2.90% of Cu, 0.12% of Co.
Upon the flotation test work, the results obtained indicated that the
concentrate obtained with use of the mixture gazoil-rinkalore RX
yielded 8.24% Cu and 0.22% Co concentrate grades with recoveries
of 76.0% Cu and 78.0% Co respectively. But, the concentrate
obtained by use of the mixture gazoil-rinkalore RX3 yielded
relatively bad results with 5.92% Cu and 0.18% Cu concentrate
grades with recoveries of 70.3% Cu and 65.3% Co respectively.
Abstract: Chitosan functionalized Fe3O4-Au core shell
nanoparticles have been prepared using a two-step wet chemical
approach using NaBH4 as reducing agent for formation of Au in
ethylene glycol. X-ray diffraction studies shows individual phases of
Fe3O4 and Au in the as prepared samples with crystallite size of 5.9
and 11.4 nm respectively. The functionalization of the core-shell
nanostructure with Chitosan has been confirmed using Fourier
transform infrared spectroscopy along with signatures of octahedral
and tetrahedral sites of Fe3O4 below 600cm-1. Mössbauer
spectroscopy shows decrease in particle-particle interaction in
presence of Au shell (72% sextet) than pure oleic coated Fe3O4
nanoparticles (88% sextet) at room temperature. At 80K, oleic acid
coated Fe3O4 shows only sextets whereas the Chitosan functionalized
Fe3O4 and Chitosan functionalized Fe3O4@Au core shell show
presence of 5 and 11% doublet, respectively.
Abstract: The effect of additional magnesium oxide (MgO) was
investigated by using the tungsten oxide supported on silica catalyst
(WOx/SiO2) physically mixed with MgO in a weight ratio 1:1. The
both fresh and spent catalysts were characterized by FT-Raman
spectrometer, UV-Vis spectrometer, X-Ray diffraction (XRD) and
temperature programmed oxidation (TPO). The results indicated that
the additional MgO could enhance the conversion of trans-2-butene
due to isomerization reaction. However, adding MgO would increase
the amount of coke deposit on the WOx/SiO2 catalyst. The TPO
profile presented two peaks when the WOx/SiO2 catalyst was
physically mixed with MgO. The further peak was suggested that
came from coke precursor could be produced by isomerization
reaction of undesired product. Then, the occurred coke precursor
could deposit and form coke on the acid catalyst.
Abstract: An unconventional composite inorganic ceramic
membrane capable of enhancing carbon dioxide emission decline was
fabricated and tested at laboratory scale in conformism to various
environmental guidelines and also to mitigate the effect of global
warming. A review of the existing membrane technologies for carbon
capture including the relevant gas transport mechanisms is presented.
Single gas permeation experiments using silica modified ceramic
membrane with internal diameter 20mm, outside diameter 25mm and
length of 368mm deposited on a macro porous support was carried
out to investigate individual gas permeation behaviours at different
pressures at room temperature. Membrane fabrication was achieved
using after a dip coating method. Nitrogen, Carbon dioxide, Argon,
Oxygen and Methane pure gases were used to investigate their
individual permeation rates at various pressures. Results show that
the gas flow rate increases with pressure drop. However above a
pressure of 3bar, CO2 permeability ratio to that of the other gases
indicated control of a more selective surface adsorptive transport
mechanism.
Abstract: Coal fly ash is formed as a solid waste product from
the combustion of coal in coal fired power stations. Huge amounts of
fly ash are produced globally every year and are predicted to
increase. Nowadays, less than half of the fly ash is used as a raw
material for cement manufacturing, construction and the rest of it is
disposed as a waste causing yet another environmental concern. For
this reason, the recycling of this kind of slurries into useful materials
is quite important in terms of economical and environmental aspects.
The purpose of this study is to evaluate the Orhaneli and
Tuncbilek coal fly ashes for utilization in some industrial
applications. Therefore the mineralogical and chemical compositions
of these fly ashes were analyzed by X-ray fluorescence spectroscopy,
ourier-transform infrared spectrometer, and X-ray diffraction. The
silicon (Si) and aluminum (Al) in the fly ashes were activated by
alkali fusion technique with sodium hydroxide. The obtained extracts
were analyzed for Si and Al content by inductively coupled plasma
optical emission spectrometry.
Abstract: Cesium iodide (CsI) melt was injected into anodic aluminum oxide (AAO) template and was solidified to CsI column. The controllable AAO channel size (10~500 nm) can makes CsI column size from 10 to 500 nm in diameter. In order to have a shorter light irradiate from each singe CsI column top to bottom the AAO template was coated a TiO2 nano-film. The TiO2 film acts a refraction film and makes X-ray has a shorter irradiation path in the CsI crystal making a stronger the photo-electron signal. When the incidence light irradiate from air (R=1.0) to CsI’s first surface (R=1.84) the first refraction happen, the first refraction continue into TiO2 film (R=2.88) and produces the low angle of the second refraction. Then the second refraction continue into AAO wall (R=1.78) and produces the third refraction after refractions between CsI and AAO wall (R=1.78) produce the fourth refraction. The incidence light through TiO2 filmand the first surface of CsI then arrive to the second surface of CsI. Therefore, the TiO2 film can has shorter refraction path of incidence light and increase the photo-electron conversion efficiency.
Abstract: Scrubbing by a liquid spraying is one of the most
effective processes used for removal of fine particles and soluble
gas pollutants (such as SO2, HCl, HF) from the flue gas. There are
many configurations of scrubbers designed to provide contact
between the liquid and gas stream for effectively capturing
particles or soluble gas pollutants, such as spray plates, packed bed
towers, jet scrubbers, cyclones, vortex and venturi scrubbers. The
primary function of venturi scrubber is the capture of fine particles
as well as HCl, HF or SO2 removal with effect of the flue gas
temperature decrease before input to the absorption column. In this
paper, sulfur dioxide (SO2) from flue gas was captured using new
design replacing venturi scrubber (1st degree of wet scrubbing).
The flue gas was prepared by the combustion of the carbon
disulfide solution in toluene (1:1 vol.) in the flame in the reactor.
Such prepared flue gas with temperature around 150°C was
processed in designed laboratory O-element scrubber. Water was
used as absorbent liquid. The efficiency of SO2 removal, pressure
drop and temperature drop were measured on our experimental
device. The dependence of these variables on liquid-gas ratio was
observed. The average temperature drop was in the range from
150°C to 40°C. The pressure drop was increased with increasing of
a liquid-gas ratio, but no too much as for the common venturi
scrubber designs. The efficiency of SO2 removal was up to 70 %.
The pressure drop of our new designed wet scrubber is similar to
commonly used venturi scrubbers; nevertheless the influence of
amount of the liquid on pressure drop is not so significant.
Abstract: Early diagnosis of infection like Hep-B virus in blood
is important for low cost medical treatment. For this purpose, it is
desirable to develop a point of care device which should be able to
detect trace quantities of the target molecule in blood. In this paper,
we report a nanoporous silicon oxide sensor which is capable of
detecting down to 1fM concentration of Hep-B surface antigen in
blood without the requirement of any centrifuge or pre-concentration.
This has been made possible by the presence of resonant peak in the
sensitivity characteristics. This peak is observed to be dependent only
on the concentration of the specific antigen and not on the interfering
species in blood serum. The occurrence of opposite impedance
change within the pores and at the bottom of the pore is responsible
for this effect. An electronic interface has also been designed to
provide a display of the virus concentration.
Abstract: Propylene self-metathesis to ethylene and butene was
studied over WOx/SiO2 catalysts at 450oC and atmospheric pressure.
The WOx/SiO2 catalysts were prepared by incipient wetness
impregnation of ammonium metatungstate aqueous solution. It was
found that, adding nano-sized extra supports (SiO2 and TiO2) by
physical mixing with the WOx/SiO2 enhanced propylene conversion.
The UV-Vis and FT-Raman results revealed that WOx could migrate
from the original silica support to the extra support, leading to a
better dispersion of WOx. The ICP-OES results also indicate that
WOx existed on the extra support. Coke formation was investigated
on the catalysts after 10 h time-on-stream by TPO. However, adding
nano-sized extra supports led to higher coke formation which may be
related to acidity as characterized by NH3-TPD.
Abstract: This paper presents the design and fabrication of an
optical window for an optical modulator toward image sensing
applications. An optical window consists of micrometer-order SiO2
capillaries (porous solid) that can modulate transmission light
intensity by moving the liquid in and out of porous solid. A high
optical transmittance of the optical window can be achieved due to
refractive index matching when the liquid is penetrated into the
porous solid. Otherwise, its light transmittance is lower because of
light reflection and scattering by air holes and capillary walls. Silicon
capillaries fabricated by deep reactive ion etching (DRIE) process are
completely oxidized to form the SiO2 capillaries. Therefore, high
aspect ratio SiO2 capillaries can be achieved based on silicon
capillaries formed by DRIE technique. Large compressive stress of
the oxide causes bending of the capillary structure, which is reduced
by optimizing the design of device structure. The large stress of the
optical window can be released via thin supporting beams. A 7.2 mm
x 9.6 mm optical window area toward a fully integrated with the
image sensor format is successfully fabricated and its optical
transmittance is evaluated with and without inserting liquids (ethanol
and matching oil). The achieved modulation range is approximately
20% to 35% with and without liquid penetration in visible region
(wavelength range from 450 nm to 650 nm).
Abstract: Feed oil samples which are used as mixed feed raw
material were taken from six different feed factories in March, May
and July. All factories make production in Konya, Turkey and all of
the samples were crude soybean oils. Physical and chemical analyses,
free radical scavenger effect, and total phenol content were
determined on these oil samples. Moisture (M) content was found
between 0.10-22.23%, saponification number (SF) was determined
143.13 to 167.93 KOH/kg, free fatty acidity (FFA) was varied 0.73 to
35.00%, peroxide value (PV) was found between 1.53 and 28.43
meq/kg, unsaponifiable matter (USM) was determined from 0.40 to
17.10%, viscosity (V) was found between 34.30 and 625.67 mPas,
sediment (S) amount was determined between 0.60-18.16%, free
radical scavenger effect (FRSE) was varied 20.7 to 43.04% inhibition
of the extract and total phenol (TPC) content was found between 1.20
and 2.69mg/L extract. Different results were found between months
and factories.
Abstract: Nanofibers of PVA /nickel nitrate/silica/alumina
izopropoxide/boric acid composite were prepared by using sol-gel
processing and electrospinning technique. By high temperature
calcinations of the above precursor fibers, nanofibers of
NiO/Al2O3/B2O3/SiO2 composite with diameters about 500 nm
could be successfully obtained. The fibers were characterized by
XRD and SEM analyses.
Abstract: Non-water based fixed abrasive polishing was adopted
to manufacture LBO crystal for nano precision surface quality because
of its deliquescent. Ethyl alcohol was selected as the non-water based
slurry solvent and ethanediamine, lactic acid, hydrogen peroxide was
added in the slurry as a chemical additive, respectively. Effect of
different additives with non-water based slurry on material removal
rate, surface topography, microscopic appearances, and surface
roughness were investigated in fixed abrasive polishing of LBO
crystal. The results show the best surface quality of LBO crystal with
surface roughness Sa 8.2 nm and small damages was obtained by
non-water based slurry with lactic acid. Non-water based fixed
abrasive polishing can achieve nano precision surface quality of LBO
crystal with high material removal.
Abstract: This article presents modeling studies of NiAl alloy
under solid-particle erosion and liquid-drop erosion. In the
solid-particle erosion simulation, attention is paid to the oxide scale
thickness variation on the alloy in high-temperature erosion
environments. The erosion damage is assumed to be deformation wear
and cutting wear mechanisms, incorporating the influence of the oxide
scale on the eroded surface; thus the instantaneous oxide thickness is
the result of synergetic effect of erosion and oxidation. For liquid-drop
erosion, special interest is in investigating the effects of drop velocity
and drop size on the damage of the target surface. The models of
impact stress wave, mean depth of penetration, and maximum depth of
erosion rate (Max DER) are employed to develop various maps for
NiAl alloy, including target thickness vs. drop size (diameter), rate of
mean depth of penetration (MDRP) vs. drop impact velocity, and
damage threshold velocity (DTV) vs. drop size.
Abstract: It is well known that in recent years magnetic
materials have received increased attention due to their properties.
For this reason a significant number of patents that were published
during the last decade are oriented towards synthesis and study of
such materials. The aim of this work is to create and study ferrite
nanocrystalline materials with spinel structure, using sol-gel
technology with participation of auto-combustion. This method is
perspective in that it is a cheap and low-temperature technique that
allows for the fine control on the product’s chemical composition.
Abstract: The objective of this work is to study the effect of two
key factors - external magnetic field and applied current density
during template-based electrodeposition of nickel nanowires using an
electrode distance of 20 mm. Morphology, length, crystallite size and
crystallographic characterization of the grown nickel nanowires at an
electrode distance of 20mm are presented. For this electrode distance
of 20 mm, these two key electrodeposition factors when coupled was
found to reduce crystallite size with a higher growth length and
preferred orientation of Ni crystals. These observed changes can be
inferred to be due to coupled interaction forces induced by the
intensity of applied electric field (current density) and external
magnetic field known as magnetohydrodynamic (MHD) effect during
the electrodeposition process.
Abstract: Corrosion of concrete sewer pipes induced by sulfuric
acid is an acknowledged problem and a ticking time-bomb to sewer
operators. Whilst the chemical reaction of the corrosion process is
well-understood, the indirect roles of other parameters in the
corrosion process which are found in sewer environment are not
highly reflected on. This paper reports on a field studies undertaken
in Austria and United Kingdom, where the parameters of
temperature, pH, H2S and CO2 were monitored over a period of time.
The study establishes that (i) effluent temperature and pH have
similar daily pattern and peak times, when examined in minutes
scale; (ii) H2S and CO2 have an identical hourly pattern; (iii) H2S
instant or shifted relation to effluent temperature is governed by the
root mean square value of CO2.
Abstract: The effect of transition metal doping on Pt/Al2O3
catalyst used in propane dehydrogenation reaction at 500°C was
studied. The preparation methods investigated were sequential
impregnation (Pt followed by the 2nd metal or the 2nd metal followed
by Pt) and co-impregnation. The metal contents of these catalysts
were fixed as the weight ratio of Pt per the 2nd metal of around 0.075.
These catalysts were characterized by N2-physisorption, TPR, COchemisorption
and NH3-TPD. It was found that the impregnated 2nd
metal had an effect upon reducibility of Pt due to its interaction with
transition metal-containing structure. This was in agreement with the
CO-chemisorption result that the presence of Pt metal, which is a
result from Pt species reduction, was decreased. The total acidity of
bimetallic catalysts is decreased but the strong acidity is slightly
increased. It was found that the stability of bimetallic catalysts
prepared by co-impregnation and sequential impregnation where the
2nd metal was impregnated before Pt were better than that of
monometallic catalyst (undoped Pt one) due to the forming of Pt sites
located on the transition metal-oxide modified surface. Among all
preparation methods, the sequential impregnation method- having Pt
impregnated before the 2nd metal gave the worst stability because this
catalyst lacked the modified Pt sites and some fraction of Pt sites was
covered by the 2nd metal.