Abstract: The proper selection of the AC-side passive filter
interconnecting the voltage source converter to the power supply is
essential to obtain satisfactory performances of an active power filter
system. The use of the LCL-type filter has the advantage of
eliminating the high frequency switching harmonics in the current
injected into the power supply. This paper is mainly focused on
analyzing the influence of the interface filter parameters on the active
filtering performances. Some design aspects are pointed out. Thus,
the design of the AC interface filter starts from transfer functions by
imposing the filter performance which refers to the significant current
attenuation of the switching harmonics without affecting the
harmonics to be compensated. A Matlab/Simulink model of the entire
active filtering system including a concrete nonlinear load has been
developed to examine the system performances. It is shown that a
gamma LC filter could accomplish the attenuation requirement of the
current provided by converter. Moreover, the existence of an optimal
value of the grid-side inductance which minimizes the total harmonic
distortion factor of the power supply current is pointed out.
Nevertheless, a small converter-side inductance and a damping
resistance in series with the filter capacitance are absolutely needed
in order to keep the ripple and oscillations of the current at the
converter side within acceptable limits. The effect of change in the
LCL-filter parameters is evaluated. It is concluded that good active
filtering performances can be achieved with small values of the
capacitance and converter-side inductance.
Abstract: This paper presents a simple and original method for
the generation of short monocycle pulses based on the transient
response of a passive band-pass filter. The recorded sub-nanosecond
pulses show a good symmetry and a small ringing (13 % of the peak
amplitude). Their spectral density covers the range 3.1 GHz to
10.6 GHz. The possibility to adapt the pulse spectral density to the
indoor FCC frequency mask is demonstrated with a prototype
working at a reduced frequency (FCC/1000). A detection technique is
proposed.
Abstract: This paper is concerned with an improved algorithm
based on the piecewise-smooth Mumford and Shah (MS) functional
for an efficient and reliable segmentation. In order to speed up
convergence, an additional force, at each time step, is introduced
further to drive the evolution of the curves instead of only driven by
the extensions of the complementary functions u + and u - . In our
scheme, furthermore, the piecewise-constant MS functional is
integrated to generate the extra force based on a temporary image that
is dynamically created by computing the union of u + and u - during
segmenting. Therefore, some drawbacks of the original algorithm,
such as smaller objects generated by noise and local minimal problem
also are eliminated or improved. The resulting algorithm has been
implemented in Matlab and Visual Cµ, and demonstrated efficiently
by several cases.
Abstract: Sol-gel method has been used to fabricate
nanocomposite films on glass substrates composed halloysite clay
mineral and nanocrystalline TiO2. The methodology for the synthesis
involves a simple chemistry method utilized nonionic surfactant
molecule as pore directing agent along with the acetic acid-based solgel
route with the absence of water molecules. The thermal treatment
of composite films at 450oC ensures elimination of organic material
and lead to the formation of TiO2 nanoparticles onto the surface of
the halloysite nanotubes. Microscopy techniques and porosimetry
methods used in order to delineate the structural characteristics of the
materials. The nanocomposite films produced have no cracks and
active anatase crystal phase with small crystallite size were deposited
on halloysite nanotubes. The photocatalytic properties for the new
materials were examined for the decomposition of the Basic Blue 41
azo dye in solution. These, nanotechnology based composite films
show high efficiency for dye’s discoloration in spite of different
halloysite quantities and small amount of halloysite/TiO2 catalyst
immobilized onto glass substrates. Moreover, we examined the
modification of the halloysite/TiO2 films with silver particles in order
to improve the photocatalytic properties of the films. Indeed, the
presence of silver nanoparticles enhances the discoloration rate of the
Basic Blue 41 compared to the efficiencies obtained for unmodified
films.
Abstract: The effect of Alumina nanoparticle size on thermophysical
properties, heat transfer performance and pressure loss characteristics of
Aviation Turbine Fuel (ATF)-Al2O3 nanofluids is studied experimentally for
the proposed application of regenerative cooling of semi-cryogenic rocket
engine thrust chambers. Al2O3 particles with mean diameters of 50 nm or 150
nm are dispersed in ATF. At 500C and 0.3% particle volume concentration,
the bigger particles show increases of 17% in thermal conductivity and 55% in
viscosity, whereas the smaller particles show corresponding increases of 21%
and 22% for thermal conductivity and viscosity respectively. Contrary to these
results, experiments to study the heat transfer performance and pressure loss
characteristics show that at the same pumping power, the maximum
enhancement in heat transfer coefficient at 500C and 0.3% concentration is
approximately 47% using bigger particles, whereas it is only 36% using
smaller particles.
Abstract: This article discusses the questions concerning of creating small packet networks for energy companies with application of high voltage power line carrier equipment (PLC) with functionality of IP traffic transmission. The main idea is to create converged PLC links between substations and dispatching centers where packet data and voice are transmitted in one data flow. The article contents description of basic conception of the network, evaluation of voice traffic transmission parameters, and discussion of header compression techniques in relation to PLC links. The results of exploration show us, that convergent packet PLC links can be very useful in the construction of small packet networks between substations in remote locations, such as deposits or low populated areas.
Abstract: In this paper, 3X3 routing nodes are proposed to
provide speedup and parallel processing capability in Data Vortex
network architectures. The new design not only significantly
improves network throughput and latency, but also eliminates the
need for distributive traffic control mechanism originally embedded
among nodes and the need for nodal buffering. The cost effectiveness
is studied by a comparison study with the previously proposed 2-
input buffered networks, and considerable performance enhancement
can be achieved with similar or lower cost of hardware. Unlike
previous implementation, the network leaves small probability of
contention, therefore, the packet drop rate must be kept low for such
implementation to be feasible and attractive, and it can be achieved
with proper choice of operation conditions.
Abstract: High strength concrete has been used in situations
where it may be exposed to elevated temperatures. Numerous authors
have shown the significant contribution of polypropylene fiber to the
spalling resistance of high strength concrete.
When cement-based composite that reinforced by polypropylene
fibers heated up to 170 °C, polypropylene fibers readily melt and
volatilize, creating additional porosity and small channels in to the
matrix that cause the poor structure and low strength.
This investigation develops on the mechanical properties of mortar
incorporating polypropylene fibers exposed to high temperature.
Also effects of different pozzolans on strength behaviour of samples
at elevated temperature have been studied.
To reach this purpose, the specimens were produced by partial
replacement of cement with finely ground glass, silica fume and rice
husk ash as high reactive pozzolans. The amount of this replacement
was 10% by weight of cement to find the effects of pozzolans as a
partial replacement of cement on the mechanical properties of
mortars. In this way, lots of mixtures with 0%, 0.5%, 1% and 1.5% of
polypropylene fibers were cast and tested for compressive and
flexural strength, accordance to ASTM standard. After that
specimens being heated to temperatures of 300, 600 °C, respectively,
the mechanical properties of heated samples were tested.
Mechanical tests showed significant reduction in compressive
strength which could be due to polypropylene fiber melting. Also
pozzolans improve the mechanical properties of sampels.
Abstract: Ultrastructure of duodenum mucosa of irradiated rat
was studied versus dose rate of irradiation following exposure to
gamma rays from 60-Cobalt source. The animals were whole body
irradiated at two dose rates (1 Gy.mn-1 and 1 Gy.h-1) and three total
doses (1, 2 or 4 Gy) for each dose rate. 24 or 48 h after irradiation,
their small intestine was removed and samples of duodenum were
processed for observations under a transmission electron microscopy.
Samples of duodenum mucosa of control rats were processed in the
same way. For the lower dose rate of 1 Gy.h-1, main lesions
characteristic of apoptosis were detected within irradiated enterocytes
at a total dose of 2 Gy and 24 h after exposure. Necrosis was noted in
the samples, 48 h after exposition. For the higher dose rate of 1
Gy.mn-1, fewer changes were detected at all total doses 24 or 48 h
irradiation. Thus, it was shown that the appearance of radiationinduced
alterations varies not only with increasing total dose and
post-irradiation time but especially with decreasing dose rate.
Abstract: Sunflower stalks were analysed for chemical
compositions: pentosan 15.84%, holocellulose 70.69%,
alphacellulose 45.74%, glucose 27.10% and xylose 7.69% based on
dry weight of 100-g raw material. The most optimum condition for
steam explosion pretreatment was as follows. Sunflower stalks were
cut into small pieces and soaked in 0.02 M H2SO4 for overnight.
After that, they were steam exploded at 207 C and 21 kg/cm2 for 3
minutes to fractionate cellulose, hemicellulose and lignin. The
resulting hydrolysate, containing hemicellulose, and cellulose pulp
contained xylose sugar at 2.53% and 7.00%, respectively.The pulp
was further subjected to enzymatic saccharification at 50 C, pH 4.8 citrate buffer) with pulp/buffer 6% (w/w)and Celluclast 1.5L/pulp
2.67% (w/w) to obtain single glucose with maximum yield 11.97%.
After fixed-bed fermentation under optimum condition using
conventional yeast mixtures to produce bioethanol, it indicated
maximum ethanol yield of 0.028 g/100 g sunflower stalk.
Abstract: High performance Resistive Random Access Memory
(RRAM) based on HfOx has been prepared and its temperature
instability has been investigated in this work. With increasing
temperature, it is found that: leakage current at high resistance state
increases, which can be explained by the higher density of traps
inside dielectrics (related to trap-assistant tunneling), leading to a
smaller On/Off ratio; set and reset voltages decrease, which may be
attributed to the higher oxygen ion mobility, in addition to the
reduced potential barrier to create / recover oxygen ions (or oxygen
vacancies); temperature impact on the RRAM retention degradation
is more serious than electrical bias.
Abstract: A lot of recent research have spoken on the relation
between the increase of the homocysteinemia and some kinds of
cancer . For that, our study was based on the research of a possible
relation between the increase of the concentration of this amino-acid
in the plasma and the appearance of the disease of the Acute
Lymphoblastic Leukaemia in a part of Algerian children with Berber
origin in the East of Algeria . The study has done on 47 ill persons
with an average age of (09±06 ) years , with whom the disease has
diagnosed by blood and marrow examination in the hospital of blood
diseases in the CHU of Batna, and on 194 healthy witnesses of the
same age. The two groups were benefited by a dosage of the
concentration of the homocysteine vitamin B9 ,vitamin B12 , and
also of the study of special polymorphisms of indispensable enzymes
in the metabolism of this acid , and that by the use of the method (
Light cycler ) Real time PCR , on the following enzymes : MS (
C2756G ), MSR ( A66G ) ,MTHFR1 ( C677T ) and MTHFR2
(A1298C). The obtained results have revealed that the rate of the
homozygote muted genotype is the less frequent in the two groups ,
and that exist at list one genotype of each enzyme in the ill group and
in which the percentage exceed with remarkable way the same
genotype in the healthy group and we notice specially the muted
genotype GG of -the methionine synthetase-and the form TT of the
enzyme – methyline tetra hydrofolate reductase – We notice the
existence of considerable number of genotypes in the ill group lied
with characteristic increase of this Amino-acid ,and that for the
reduction of the biologic activity of these enzymes which become
inefficient in the transfer of the homocysteine into the methionine
and cause the diminution of the biologic activity of these enzymes
and with consequence the reduction of the percentage of methylic
radicals in the DNA of studied genes and that lead to the increase of
the activity and the capacity of transcription , and it-s so probably
that this last one is one of the factors of this disease especially if we
know that the specific check-up of vitamins is normal and similar in
the two groups , which ovoid the hypothesis of the reduction of
vitamins . We notice also that the heterozygote genotype is the less in
the sick category except the MTHFR2. Wild genotype is more
frequent in the witness group except MSR. Even these results are
partials; they open a new way in the genetic diagnosis of this
malicious disease which allow a precocious diagnosis and the use of
an effective and appropriated treatment in the same time.
Abstract: Because of its global reach, reduction of time
restraints, and ability to reduce costs and increase sales, use of the
Internet, the World Wide Web (WWW), and related technologies
can be a competitive tool in the arsenal of small and medium-sized
enterprises (SMEs). Countries the world over are interested in the
successful adoption of the Internet by SMEs. Because a vast
majority of jobs come from that sector, greater financial success of
SMEs translates into greater job growth and, subsequently, higher
tax revenue to the government. This research investigated the level
of Internet usage for business solutions by small and medium
enterprises in Jordan. Through the survey of a random sample of
100 firms with less than 500 employees and from data obtained
from this survey that formed the basis for our study, we found that
a majority of respondents use the Internet in business activities ,
the adoption of the Internet as a business tool is limited to a
brochure where Web site which primarily provides one way. As
such, there wasn't interactive information about the company and
its products and services.
Abstract: High Power Lasers produce an intense burst of
Bremmstrahlung radiation which has potential applications in broadband
x-ray radiography. Since the radiation produced is through the
interaction of accelerated electrons with the remaining laser target,
these bursts are extremely short – in the region of a few ps. As a
result, the laser-produced x-rays are capable of imaging complex
dynamic objects with zero motion blur.
Abstract: Thrombosis can be life threatening, necessitating therefore its instant treatment. Hydergine, a nootropic agent is used as a cognition enhancer in stroke patients but relatively little is known about its anti-thrombolytic effect. To investigate this aspect, in vivo and ex vivo experiments were designed and conducted. Three groups of rats were injected 1.5mg, 3.0mg and 4.5mg hydergine intraperitonealy with and without prior exposure to fresh plasma. Positive and negative controls were run in parallel. Animals were sacrificed after 1.5hrs and BT, CT, PT, INR, APTT, plasma calcium levels were estimated. For ex vivo analyses, each 1ml blood aspirated was exposed to 0.1mg, 0.2mg, 0.3mg dose of hydergine with parallel controls. Parameters analyzed were as above. Statistical analysis was through one-way ANOVA. Dunken-s and Tukey-s tests provided intra-group variance. BT, CT, PT, INR and APTT increased while calcium levels dropped significantly (P
Abstract: In this paper, Fabless Prototyping Methodology is
introduced for the design and analysis of MEMS devices.
Conventionally Finite Element Analysis (FEA) is performed before
system level simulation. In our proposed methodology, system level
simulation is performed earlier than FEA as it is computationally less
extensive and low cost. System level simulations are based on
equivalent behavioral models of MEMS device. Electrostatic
actuation based MEMS Microgripper is chosen as case study to
implement this methodology. This paper addresses the behavioral
model development and simulation of actuator part of an
electrostatically actuated Microgripper. Simulation results show that
the actuator part of Microgripper works efficiently for a voltage range
of 0-45V with the corresponding jaw displacement of 0-4.5425μm.
With some minor changes in design, this range can be enhanced to
15μm at 85V.
Abstract: Incremental forming is a complex forming process with
continuously local cumulative deformation taking place during its
process, and springback that forming quality affected by would occur.
The springback evaluation method based on forming error
compensation also was proposed, which it can be defined as the
difference between theory and the actual amount of compensation
along the measured direction. According to forming error
compensation evaluation method, experiments was designed and
implemented. And from the results that obtained it can be show, the
magnitude of springback average (δE) of formed parts was very small,
and the forming precision could be significantly improved by adopting
compensation method. Based on double tensile stress state in the main
deformation area, a hypothesis that there is little springback be arisen
by bending behavior on the formed parts that was proposed.
Abstract: Considering the theory of attribute grammars, we use
logical formulas instead of traditional functional semantic rules.
Following the decoration of a derivation tree, a suitable algorithm
should maintain the consistency of the formulas together with the
evaluation of the attributes. This may be a Prolog-like resolution, but
this paper examines a somewhat different strategy, based on
production specialization, local consistency and propagation: given a
derivation tree, it is interactively decorated, i.e. incrementally
checked and evaluated. The non-directed dependencies are
dynamically directed during attribute evaluation.
Abstract: To achieve reliable solutions, today-s numerical and
experimental activities need developing more accurate methods and
utilizing expensive facilities, respectfully in microchannels. The analytical
study can be considered as an alternative approach to alleviate
the preceding difficulties. Among the analytical solutions, those with
high robustness and low complexities are certainly more attractive.
The perturbation theory has been used by many researchers to analyze
microflows. In present work, a compressible microflow with constant
heat flux boundary condition is analyzed. The flow is assumed to be
fully developed and steady. The Mach and Reynolds numbers are also
assumed to be very small. For this case, the creeping phenomenon
may have some effect on the velocity profile. To achieve robustness
solution it is assumed that the flow is quasi-isothermal. In this study,
the creeping term which appears in the slip boundary condition
is formulated by different mathematical formulas. The difference
between this work and the previous ones is that the creeping term
is taken into account and presented in non-dimensionalized form.
The results obtained from perturbation theory are presented based
on four non-dimensionalized parameters including the Reynolds,
Mach, Prandtl and Brinkman numbers. The axial velocity, normal
velocity and pressure profiles are obtained. Solutions for velocities
and pressure for two cases with different Br numbers are compared
with each other and the results show that the effect of creeping
phenomenon on the velocity profile becomes more important when
Br number is less than O(ε).
Abstract: A Finite Volume method based on Characteristic Fluxes for compressible fluids is developed. An explicit cell-centered resolution is adopted, where second and third order accuracy is provided by using two different MUSCL schemes with Minmod, Sweby or Superbee limiters for the hyperbolic part. Few different times integrator is used and be describe in this paper. Resolution is performed on a generic unstructured Cartesian grid, where solid boundaries are handled by a Cut-Cell method. Interfaces are explicitely advected in a non-diffusive way, ensuring local mass conservation. An improved cell cutting has been developed to handle boundaries of arbitrary geometrical complexity. Instead of using a polygon clipping algorithm, we use the Voxel traversal algorithm coupled with a local floodfill scanline to intersect 2D or 3D boundary surface meshes with the fixed Cartesian grid. Small cells stability problem near the boundaries is solved using a fully conservative merging method. Inflow and outflow conditions are also implemented in the model. The solver is validated on 2D academic test cases, such as the flow past a cylinder. The latter test cases are performed both in the frame of the body and in a fixed frame where the body is moving across the mesh. Adaptive Cartesian grid is provided by Paramesh without complex geometries for the moment.