Abstract: In recent years there has been renewal of interest in the
relation between Green IT and Cloud Computing. The growing use of
computers in cloud platform has caused marked energy consumption,
putting negative pressure on electricity cost of cloud data center. This
paper proposes an effective mechanism to reduce energy utilization in
cloud computing environments. We present initial work on the
integration of resource and power management that aims at reducing
power consumption. Our mechanism relies on recalling virtualization
services dynamically according to user-s virtualization request and
temporarily shutting down the physical machines after finish in order
to conserve energy. Given the estimated energy consumption, this
proposed effort has the potential to positively impact power
consumption. The results from the experiment concluded that energy
indeed can be saved by powering off the idling physical machines in
cloud platforms.
Abstract: Primary barrier of membrane type LNG containment system consist of corrugated 304L stainless steel. This 304L stainless steel is austenitic stainless steel which shows different material behaviors owing to phase transformation during the plastic work. Even though corrugated primary barriers are subjected to significant amounts of pre-strain due to press working, quantitative mechanical behavior on the effect of pre-straining at cryogenic temperatures are not available. In this study, pre-strain level and pre-strain temperature dependent tensile tests are carried to investigate mechanical behaviors. Also, constitutive equations with material parameters are suggested for a verification study.
Abstract: Wheat gluten hydrolyzates (WGHs) and anchovy fine
powder hydrolyzates (AFPHs) were produced at 300 MPa using
combinations of Flavourzyme 500MG (F), Alcalase 2.4L (A),
Marugoto E (M) and Protamex (P), and then were compared to those
produced at ambient pressure concerning the contents of soluble solid
(SS), soluble nitrogen and electrophoretic profiles. The contents of SS
in the WGHs and AFPHs increased up to 87.2% according to the
increase in enzyme number both at high and ambient pressure. Based
on SS content, the optimum enzyme combinations for one-, two-,
three- and four-enzyme hydrolysis were determined as F, FA, FAM
and FAMP, respectively. Similar trends were found for the contents of
total soluble nitrogen (TSN) and TCA-soluble nitrogen (TCASN). The
contents of SS, TSN and TCASN in the hydrolyzates together with
electrophoretic mobility maps indicates that the high-pressure
treatment of this study accelerated protein hydrolysis compared to
ambient-pressure treatment.
Abstract: To improve the classification rate of the face
recognition, features combination and a novel non-linear kernel are
proposed. The feature vector concatenates three different radius of
local binary patterns and Gabor wavelet features. Gabor features are
the mean, standard deviation and the skew of each scaling and
orientation parameter. The aim of the new kernel is to incorporate
the power of the kernel methods with the optimal balance between
the features. To verify the effectiveness of the proposed method,
numerous methods are tested by using four datasets, which are
consisting of various emotions, orientations, configuration,
expressions and lighting conditions. Empirical results show the
superiority of the proposed technique when compared to other
methods.
Abstract: An advanced composite flywheel rotor consisting of
intra and inter hybrid rims was designed to optimally increase the energy capacity, and was manufactured using filament winding with
in-situ curing. The flywheel has recently attracted considerable attention from many investigators since it possesses great potential in
many energy storage applications, including electric utilities, hybrid or
electric automobiles, and space vehicles. In this investigation, a comprehensive study was conducted with the intent to implement
composites in high performance flywheel applications.The inner two
intra-hybrid rims (rims 1 and 2) were manufactured as a whole part
through continuous filament winding under in-situ curing conditions,
and so were the outer two rims (rims 3 and 4). The outer surface of rim
2 and the inner surface of rim 3 were CNC-tapered for press-fitting. Machined rims were finally press-fitted using a hydraulic press with a
maximum compressive force of approximately 1000 ton.
Abstract: Modeling of a heterogeneous industrial fixed bed
reactor for selective dehydrogenation of heavy paraffin with Pt-Sn-
Al2O3 catalyst has been the subject of current study. By applying
mass balance, momentum balance for appropriate element of reactor
and using pressure drop, rate and deactivation equations, a detailed
model of the reactor has been obtained. Mass balance equations have
been written for five different components. In order to estimate
reactor production by the passage of time, the reactor model which is
a set of partial differential equations, ordinary differential equations
and algebraic equations has been solved numerically.
Paraffins, olefins, dienes, aromatics and hydrogen mole percent as
a function of time and reactor radius have been found by numerical
solution of the model. Results of model have been compared with
industrial reactor data at different operation times. The comparison
successfully confirms validity of proposed model.
Abstract: Today with the rapid growth of telecommunications equipment, electronic and developing more and more networks of power, influence of electromagnetic waves on one another has become hot topic discussions. So in this article, this issue and appropriate mechanisms for EMC operations have been presented. First, impact of high voltage lines on the surrounding environment especially on the control room has been investigated, then to reduce electromagnetic radiation, various methods of shielding are provided and shielding effectiveness of them has been compared. It should be expressed that simulations have been done by the finite element method (FEM).
Abstract: Information is increasing in volumes; companies are overloaded with information that they may lose track in getting the intended information. It is a time consuming task to scan through each of the lengthy document. A shorter version of the document which contains only the gist information is more favourable for most information seekers. Therefore, in this paper, we implement a text summarization system to produce a summary that contains gist information of oil and gas news articles. The summarization is intended to provide important information for oil and gas companies to monitor their competitor-s behaviour in enhancing them in formulating business strategies. The system integrated statistical approach with three underlying concepts: keyword occurrences, title of the news article and location of the sentence. The generated summaries were compared with human generated summaries from an oil and gas company. Precision and recall ratio are used to evaluate the accuracy of the generated summary. Based on the experimental results, the system is able to produce an effective summary with the average recall value of 83% at the compression rate of 25%.
Abstract: This paper presents the significant factor and give
some suggestion that should know before design. The main objective of this paper is guide the first step for someone who attends to design of grounding system before study in details later. The overview of
grounding system can protect damage from fault such as can save a human life and power system equipment. The unsafe conditions have
three cases. Case 1) maximum touch voltage exceeds the safety
criteria. In this case, the conductor compression ratio of the ground gird should be first adjusted to have optimal spacing of ground grid
conductors. If it still over limit, earth resistivity should be consider afterward. Case 2) maximum step voltage exceeds the safety criteria.
In this case, increasing the number of ground grid conductors around
the boundary can solve this problem. Case 3) both of maximum touch
and step voltage exceed the safety criteria. In this case, follow the solutions explained in case 1 and case 2. Another suggestion, vary depth of ground grid until maximum step and touch voltage do not
exceed the safety criteria.
Abstract: The objective of the present study was to evaluate the
potential of hollow microneedles for enhancing the transdermal
delivery of Bovine Serum Albumin (MW~66,000 Da)-Fluorescein
Isothiocyanate (BSA-FITC) conjugate, a hydrophilic large molecular
compound. Moreover, the effect of different formulations was
evaluated. The series of binary mixtures composed of propylene
glycol (PG) and pH 7.4 phosphate buffer solution (PBS) was
prepared and used as a medium for BSA-FITC. The results showed
that there was no permeation of BSA-FITC solution across the
neonatal porcine skin without using hollow microneedles, whereas
the cumulative amount of BSA-FITC released at 8 h through the
neonatal porcine skin was about 60-70% when using hollow
microneedles. Furthermore, the results demonstrated that the higher
volume of PG in binary mixtures injected, the lower cumulative
amount of BSA-FITC released and release rate of BSA-FITC from
skin. These release profiles of BSA-FITC in binary mixtures were
expressed by Fick-s law of diffusion. These results suggest the
utilization of hollow microneedle to enhance transdermal delivery of
protein and provide useful information for designing an effective
hollow microneedle system.
Abstract: As in other countries from Central and Eastern Europe,
the economic restructuring occurred in the last decade of the
twentieth century affected the mining industry in Romania, an
oversize and heavily subsidized sector before 1989. After more than
a decade since the beginning of mining restructuring, an evaluation
of current social implications of the process it is required, together
with an efficiency analysis of the adaptation mechanisms developed
at governmental level. This article aims to provide an insight into
these issues through case studies conducted in the most important
coal basin of Romania, Petroşani Depression.
Abstract: Mycophenolic acid “MPA" is a secondary metabolite
of Penicillium bervicompactum with antibiotic and
immunosuppressive properties. In this study, fermentation process
was established for production of mycophenolic acid by Penicillium
bervicompactum MUCL 19011 in shake flask. The maximum MPA
production, product yield and productivity were 1.379 g/L, 18.6 mg/g
glucose and 4.9 mg/L.h respectively. Glucose consumption, biomass
and MPA production profiles were investigated during fermentation
time. It was found that MPA production starts approximately after
180 hours and reaches to a maximum at 280 h. In the next step, the
effects of methionine and acetate concentrations on MPA production
were evaluated. Maximum MPA production, product yield and
productivity (1.763 g/L, 23.8 mg/g glucose and 6.30 mg/L. h
respectively) were obtained with using 2.5 g/L methionine in culture
medium. Further addition of methionine had not more positive effect
on MPA production. Finally, results showed that the addition of
acetate to the culture medium had not any observable effect on MPA
production
Abstract: The main aim of this research is to study the possible
use of recycled fine aggregate made from waste rubble wall to
substitute partially for the natural sand used in the production of
cement and sand bricks. The bricks specimens were prepared by
using 100% natural sand; they were then replaced by recycled fine
aggregate at 25, 50, 75, and 100% by weight of natural sand. A series
of tests was carried out to study the effect of using recycled aggregate
on the physical and mechanical properties of bricks, such as density,
drying shrinkage, water absorption characteristic, compressive and
flexural strength. Test results indicate that it is possible to
manufacture bricks containing recycled fine aggregate with good
characteristics that are similar in physical and mechanical properties
to those of bricks with natural aggregate, provided that the percentage
of recycled fine aggregates is limited up to 50-75%.
Abstract: This paper aims to discuss the influence of resistance
characteristic on the high conductive concrete considering the changes
of voltage and environment. The high conductive concrete with
appropriate proportion is produced to the press-electrode method. The
curve of resistivity with the changes of voltage and environment is
plotted and the changes of resistivity are explored.
Abstract: A new concept for long-term reagent storage for Labon- a-Chip (LoC) devices is described. Here we present a polymer multilayer stack with integrated stick packs for long-term storage of several liquid reagents, which are necessary for many diagnostic applications. Stick packs are widely used in packaging industry for storing solids and liquids for long time. The storage concept fulfills two main requirements: First, a long-term storage of reagents in stick packs without significant losses and interaction with surroundings, second, on demand releasing of liquids, which is realized by pushing a membrane against the stick pack through pneumatic pressure. This concept enables long-term on-chip storage of liquid reagents at room temperature and allows an easy implementation in different LoC devices.
Abstract: The purpose of research was to know the role of
immunogenic protein of 49 kDa from V.alginolyticus which capable
to initiate molecule expression of MHC Class II in receptor of
Cromileptes altivelis. The method used was in vivo experimental
research through testing of immunogenic protein 49 kDa from
V.alginolyticus at Cromileptes altivelis (size of 250 - 300 grams)
using 3 times booster by injecting an immunogenic protein in a
intramuscular manner. Response of expressed MHC molecule was
shown using immunocytochemistry method and SEM. Results
indicated that adhesin V.alginolyticus 49 kDa which have
immunogenic character could trigger expression of MHC class II on
receptor of grouper and has been proven by staining using
immunocytochemistry and SEM with labeling using antibody anti
MHC (anti mouse). This visible expression based on binding between
epitopes antigen and antibody anti MHC in the receptor. Using
immunocytochemistry, intracellular response of MHC to in vivo
induction of immunogenic adhesin from V.alginolyticus was shown.
Abstract: Analytical expression for maximum power transfer
through a transmission line limited by voltage stability has been
formulated using exact representation of transmission line with
ABCD parameters. The expression has been used for plotting PV
curve at different power factors of a radial transmission line.
Limiting values of reactive power have been obtained.
Abstract: Day by day technology increases and problems
associated with this technology also increase. Several researches
were carried out to investigate the deployment of such material safely
in geotechnical engineering in particular and civil engineering in
general. However, different types of waste material have such as
cement duct, fly ash and slag been proven to be suitable in several
applications. In this research cement dust mixed with different
percentages of sand will be used in some civil engineering
application as will be explained later in this paper throughout filed
and laboratory test. The used mixer (waste material with sand) prove
high performance, durability to environmental condition, low cost
and high benefits. At higher cement dust ratio, small cement ratio is
valuable for compressive strength and permeability. Also at small
cement dust ratio higher cement ratio is valuable for compressive
strength.
Abstract: Digital watermarking in medical images can ensure
the authenticity and integrity of the image. This design paper reviews
some existing watermarking schemes and proposes a reversible
tamper detection and recovery watermarking scheme. Watermark
data from ROI (Region Of Interest) are stored in RONI (Region Of
Non Interest). The embedded watermark allows tampering detection
and tampered image recovery. The watermark is also reversible and
data compression technique was used to allow higher embedding
capacity.
Abstract: In this paper we present an adaptive method for image
compression that is based on complexity level of the image. The
basic compressor/de-compressor structure of this method is a multilayer
perceptron artificial neural network. In adaptive approach
different Back-Propagation artificial neural networks are used as
compressor and de-compressor and this is done by dividing the
image into blocks, computing the complexity of each block and then
selecting one network for each block according to its complexity
value. Three complexity measure methods, called Entropy, Activity
and Pattern-based are used to determine the level of complexity in
image blocks and their ability in complexity estimation are evaluated
and compared. In training and evaluation, each image block is
assigned to a network based on its complexity value. Best-SNR is
another alternative in selecting compressor network for image blocks
in evolution phase which chooses one of the trained networks such
that results best SNR in compressing the input image block. In our
evaluations, best results are obtained when overlapping the blocks is
allowed and choosing the networks in compressor is based on the
Best-SNR. In this case, the results demonstrate superiority of this
method comparing with previous similar works and JPEG standard
coding.