Abstract: This project aims at building an efficient and
automatic power monitoring SCADA system, which is capable of
monitoring the electrical parameters of high voltage powered devices
in real time for example RMS voltage and current, frequency, energy
consumed, power factor etc. The system uses RS-485 serial
communication interface to transfer data over longer distances.
Embedded C programming is the platform used to develop two
hardware modules namely: RTU and Master Station modules, which
both use the CC2540 BLE 4.0 microcontroller configured in slave /
master mode. The Si8900 galvanic ally isolated microchip is used to
perform ADC externally. The hardware communicates via UART
port and sends data to the user PC using the USB port. Labview
software is used to design a user interface to display current state of
the power loads being monitored as well as logs data to excel
spreadsheet file. An understanding of the Si8900’s auto baud rate
process is key to successful implementation of this project.
Abstract: In this current contribution, authors are dedicated to
investigate influence of the crystal lamellae orientation on
electromechanical behaviors of relaxor ferroelectric Poly
(vinylidene fluoride –trifluoroethylene -chlorotrifluoroethylene)
(P(VDF-TrFE-CTFE)) films by control of polymer microstructure,
aiming to picture the full map of structure-property relationship. In
order to define their crystal orientation films, terpolymer films were
fabricated by solution-casting, stretching and hot-pressing process.
Differential scanning calorimetry, impedance analyzer, and tensile
strength techniques were employed to characterize crystallographic
parameters, dielectric permittivity, and elastic Young’s modulus
respectively. In addition, large electrical induced out-of-plane
electrostrictive strain was obtained by cantilever beam mode.
Consequently, as-casted pristine films exhibited surprisingly high
electrostrictive strain 0.1774% due to considerably small value of
elastic Young’s modulus although relatively low dielectric
permittivity. Such reasons contributed to large mechanical elastic
energy density. Instead, due to 2 folds increase of elastic Young’s
modulus and less than 50% augmentation of dielectric constant, fullycrystallized
film showed weak electrostrictive behavior and
mechanical energy density as well. And subjected to mechanical
stretching process, Film C exhibited stronger dielectric constant and
out-performed electrostrictive strain over Film B because edge-on
crystal lamellae orientation induced by uniaxially mechanical stretch.
Hot-press films were compared in term of cooling rate. Rather large
electrostrictive strain of 0.2788% for hot-pressed Film D in
quenching process was observed although its dielectric permittivity
equivalent to that of pristine as-casted Film A, showing highest
mechanical elastic energy density value of 359.5 J/m3. In hot-press
cooling process, dielectric permittivity of Film E saw values at 48.8
concomitant with ca.100% increase of Young’s modulus. Films with
intermediate mechanical energy density were obtained.
Abstract: Nanofibers are defined as fibers with diameters less
than 100 nanometers. In this study, behaviours of activated carbon
nanofiber (ACNF), carbon nanofiber (CNF), polyacrylonitrile/ carbon
nanotube (PAN/CNT), polyvinyl alcohol/nanosilver (PVA/Ag) in
proton exchange membrane (PEM) fuel cells are investigated
experimentally. This material was used as gas diffusion layer (GDL)
in PEM fuel cells. In this study, the electrical conductivities of
nanofiber and nanofiber/nanoparticles have been studied to
understand their effects on PEM fuel cell performance. According to
the experimental results, the maximum electrical conductivity
performance of the fuel cell with nanofiber was found to be at
PVA/Ag (at UConn condition). The electrical conductivities of CNF,
ACNF, PAN/CNT are lower for PEM. The resistance of cell with
PVA/Ag is lower than the resistance of cell with PAN/CNT, ACNF,
CNF.
Abstract: The paper focuses on the distance laboratory
organisation for training the electrical engineering staff and students
in the fields of electrical drive and power electronics. To support
online knowledge acquisition and professional enhancement, new
challenges in remote education based on an active learning approach
with self-assessment have been emerged by the authors. Following
the literature review and explanation of the improved assessment
methodology, the concept and technological basis of the labs
arrangement are presented. To decrease the gap between the distance
study of the up-to-date equipment and other educational activities in
electrical engineering, the improvements in the following-up the
learners’ progress and feedback composition are introduced. An
authoring methodology that helps to personalise knowledge
acquisition and enlarge Web-based possibilities is described.
Educational management based on self-assessment is discussed.
Abstract: The field of instrumentation electronics is undergoing
an explosive growth, due to its wide range of applications. The
proliferation of electrical devices in a close working proximity can
negatively influence each other’s performance. The degradation in
the performance is due to electromagnetic interference (EMI). This paper investigates the negative effects of electromagnetic
interference originating in the General Purpose Interface Bus (GPIB)
control-network of the AC-DC transfer measurement system.
Remedial measures of reducing measurement errors and failure of
range of industrial devices due to EMI have been explored. The ACDC
transfer measurement system was analysed for the commonmode
(CM) EMI effects. Further investigation of coupling path as
well as much accurate identification of noise propagation mechanism
has been outlined. To prevent the occurrence of common-mode
(ground loops) which was identified between the GPIB system
control circuit and the measurement circuit, a microcontroller-driven
GPIB switching isolator device was designed, prototyped,
programmed and validated. This mitigation technique has been
explored to reduce EMI effectively.
Abstract: Weak damping of low frequency oscillations is a frequent phenomenon in electrical power systems. These frequencies can be damped by power system stabilizers. Unified power flow controller (UPFC), as one of the most important FACTS devices, can be applied to increase the damping of power system oscillations and the more effect of this controller on increasing the damping of oscillations depends on its proper placement in power systems. In this paper, a technique based on controllability is proposed to select proper location of UPFC and the best input control signal in order to enhance damping of power oscillations. The effectiveness of the proposed technique is demonstrated in IEEE 9 bus power system.
Abstract: Mineral product, waste concrete (fine aggregates),
waste in the optical field, industry, and construction employ separators
to separate solids and classify them according to their size. Various
sorting machines are used in the industrial field such as those operating
under electrical properties, centrifugal force, wind power, vibration,
and magnetic force. Study on separators has been carried out to
contribute to the environmental industry. In this study, we perform
CFD analysis for understanding the basic mechanism of the separation
of waste concrete (fine aggregate) particles from air with a machine
built with a rotor with blades. In CFD, we first performed
two-dimensional particle tracking for various particle sizes for the
model with 1 degree, 1.5 degree, and 2 degree angle between each
blade to verify the boundary conditions and the method of rotating
domain method to be used in 3D. Then we developed 3D numerical
model with ANSYS CFX to calculate the air flow and track the
particles. We judged the capability of particle separation for given size
by counting the number of particles escaping from the domain toward
the exit among 10 particles issued at the inlet. We confirm that
particles experience stagnant behavior near the exit of the rotating
blades where the centrifugal force acting on the particles is in balance
with the air drag force. It was also found that the minimum particle
size that can be separated by the machine with the rotor is determined
by its capability to stay at the outlet of the rotor channels.
Abstract: River Hindon is an important river catering the
demand of highly populated rural and industrial cluster of western
Uttar Pradesh, India. Water quality of river Hindon is deteriorating at
an alarming rate due to various industrial, municipal and agricultural
activities. The present study aimed at identifying the pollution
sources and quantifying the degree to which these sources are
responsible for the deteriorating water quality of the river. Various
water quality parameters, like pH, temperature, electrical
conductivity, total dissolved solids, total hardness, calcium, chloride,
nitrate, sulphate, biological oxygen demand, chemical oxygen
demand, and total alkalinity were assessed. Water quality data
obtained from eight study sites for one year has been subjected to the
two multivariate techniques, namely, principal component analysis
and cluster analysis. Principal component analysis was applied with
the aim to find out spatial variability and to identify the sources
responsible for the water quality of the river. Three Varifactors were
obtained after varimax rotation of initial principal components using
principal component analysis. Cluster analysis was carried out to
classify sampling stations of certain similarity, which grouped eight
different sites into two clusters. The study reveals that the
anthropogenic influence (municipal, industrial, waste water and
agricultural runoff) was the major source of river water pollution.
Thus, this study illustrates the utility of multivariate statistical
techniques for analysis and elucidation of multifaceted data sets,
recognition of pollution sources/factors and understanding
temporal/spatial variations in water quality for effective river water
quality management.
Abstract: This study aims to establish function point process
based on stochastic distribution. In order to demonstrate effectiveness
of the study we present a case study that it applies suggested method
on an automotive electrical and electronics system software
development based on Monte Carlo Simulation. It is expected that the
result of this paper is used as guidance for establishing function point
process in organizations and tools for helping project managers make
decisions correctly.
Abstract: Microcantilevers are the basic MEMS devices, which
can be used as sensors, actuators and electronics can be easily built
into them. The detection principle of microcantilever sensors is based
on the measurement of change in cantilever deflection or change in its
resonance frequency. The objective of this work is to explore the
analogies between mechanical and electrical equivalent of
microcantilever beams. Normally scientists and engineers working in
MEMS use expensive software like CoventorWare, IntelliSuite,
ANSYS/Multiphysics etc. This paper indicates the need of developing
electrical equivalent of the MEMS structure and with that, one can
have a better insight on important parameters, and their interrelation of
the MEMS structure. In this work, considering the mechanical model
of microcantilever, equivalent electrical circuit is drawn and using
force-voltage analogy, it is analyzed with circuit simulation software.
By doing so, one can gain access to powerful set of intellectual tools
that have been developed for understanding electrical circuits Later
the analysis is performed using ANSYS/Multiphysics - software based
on finite element method (FEM). It is observed that both mechanical
and electrical domain results for a rectangular microcantlevers are in
agreement with each other.
Abstract: This paper introduces a signal monitoring program
developed with a view to helping electrical engineering students get
familiar with sensors with digital output. Because the output of digital
sensors cannot be simply monitored by a measuring instrument such as
an oscilloscope, students tend to have a hard time dealing with digital
sensors. The monitoring program runs on a PC and communicates with
an MCU that reads the output of digital sensors via an asynchronous
communication interface. Receiving the sensor data from the MCU,
the monitoring program shows time and/or frequency domain plots of
the data in real time. In addition, the monitoring program provides a
serial terminal that enables the user to exchange text information with
the MCU while the received data is plotted. The user can easily
observe the output of digital sensors and configure the digital sensors
in real time, which helps students who do not have enough experiences
with digital sensors. Though the monitoring program was programmed
in the Matlab programming language, it runs without the Matlab since
it was compiled as a standalone executable.
Abstract: The power electronic components within Electric Vehicles (EV) need to operate in several important modes. Some modes directly influence safety, while others influence vehicle performance. Given the variety of functions and operational modes required of the power electronics, it needs to meet efficiency requirements to minimize power losses. Another challenge in the control and construction of such systems is the ability to support bidirectional power flow. This paper considers the construction, operation, and feasibility of available converters for electric vehicles with feasible configurations of electrical buses and loads. This paper describes logic and control signals for the converters for different operations conditions based on the efficiency and energy usage bases.
Abstract: Selenium is an-antioxidant which is important for
human health enters food chain through crops. In Kenya Zea mays is
consumed by 96% of population hence is a cheap and convenient
method to provide selenium to large number of population. Several
soil factors are known to have antagonistic effects on selenium
speciation hence the uptake by Zea mays. There are no studies in
Kenya that has been done to determine the effects of soil
characteristics (pH, Tcarbon, CEC, Eh) affect accumulation of
selenium in Zea mays grains in Maize Belt in Kenya. About 100 Zea mays grain samples together with 100 soil samples
were collected from the study site put in separate labeled Ziplocs and
were transported to laboratories at room temperature for analysis.
Maize grains were analyzed for selenium while soil samples were
analyzed for pH, Cat Ion Exchange Capacity, total carbon, and
electrical conductivity. The mean selenium in Zea mays grains varied from 1.82 ± 0.76
mg/Kg to 11±0.86 mg/Kg. There was no significant difference
between selenium levels between different grain batches {χ (Df =76)
= 26.04 P= 1.00} The pH levels varied from 5.43± 0.58 to 5.85±
0.32. No significant correlations between selenium in grains and soil
pH (Pearson’s correlations = - 0.143), and between selenium levels in
grains and the four (pH, Tcarbon, CEC, Eh) soil chemical
characteristics {F (4,91) = 0.721 p = 0.579} was observed. It can be concluded that the soil chemical characteristics in the
study site did not significantly affect the accumulation of native
selenium in Zea mays grains.
Abstract: Lateral Geniculate Nucleus (LGN) is the relay center
in the visual pathway as it receives most of the input information
from retinal ganglion cells (RGC) and sends to visual cortex. Low
threshold calcium currents (IT) at the membrane are the unique
indicator to characterize this firing functionality of the LGN neurons
gained by the RGC input. According to the LGN functional
requirements such as functional mapping of RGC to LGN, the
morphologies of the LGN neurons were developed. During the
neurological disorders like glaucoma, the mapping between RGC and
LGN is disconnected and hence stimulating LGN electrically using
deep brain electrodes can restore the functionalities of LGN. A
computational model was developed for simulating the LGN neurons
with three predominant morphologies each representing different
functional mapping of RGC to LGN. The firings of action potentials
at LGN neuron due to IT were characterized by varying the
stimulation parameters, morphological parameters and orientation. A
wide range of stimulation parameters (stimulus amplitude, duration
and frequency) represents the various strengths of the electrical
stimulation with different morphological parameters (soma size,
dendrites size and structure). The orientation (0-1800) of LGN
neuron with respect to the stimulating electrode represents the angle
at which the extracellular deep brain stimulation towards LGN
neuron is performed. A reduced dendrite structure was used in the
model using Bush–Sejnowski algorithm to decrease the
computational time while conserving its input resistance and total
surface area. The major finding is that an input potential of 0.4 V is
required to produce the action potential in the LGN neuron which is
placed at 100 μm distance from the electrode. From this study, it can
be concluded that the neuroprostheses under design would need to
consider the capability of inducing at least 0.4V to produce action
potentials in LGN.
Abstract: This paper describes the development of a DNA-based
nanobiosensor to detect the dengue virus in mosquito using
electrically active magnetic (EAM) nanoparticles as concentrator and
electrochemical transducer. The biosensor detection encompasses
two sets of oligonucleotide probes that are specific to the dengue
virus: the detector probe labeled with the EAM nanoparticles and the
biotinylated capture probe. The DNA targets are double hybridized to
the detector and the capture probes and concentrated from
nonspecific DNA fragments by applying a magnetic field.
Subsequently, the DNA sandwiched targets (EAM-detector probe–
DNA target–capture probe-biotin) are captured on streptavidin
modified screen printed carbon electrodes through the biotinylated
capture probes. Detection is achieved electrochemically by measuring
the oxidation–reduction signal of the EAM nanoparticles. Results
indicate that the biosensor is able to detect the redox signal of the
EAM nanoparticles at dengue DNA concentrations as low as 10
ng/μl.
Abstract: A geoelectric survey was carried out in some parts of
Angwan Gwari, an outskirt of Lapai Local Government Area on
Niger State which belongs to the Nigerian Basement Complex, with
the aim of evaluating the soil corrosivity, aquifer transmissivity and
protective capacity of the area from which aquifer characterisation
was made. The G41 Resistivity Meter was employed to obtain fifteen
Schlumberger Vertical Electrical Sounding data along profiles in a
square grid network. The data were processed using interpex 1-D
sounding inversion software, which gives vertical electrical sounding
curves with layered model comprising of the apparent resistivities,
overburden thicknesses, and depth. This information was used to
evaluate longitudinal conductance and transmissivities of the layers.
The results show generally low resistivities across the survey area
and an average longitudinal conductance variation from
0.0237Siemens in VES 6 to 0.1261Siemens in VES 15 with almost
the entire area giving values less than 1.0 Siemens. The average
transmissivity values range from 96.45 Ω.m2 in VES 4 to 299070
Ω.m2 in VES 1. All but VES 4 and VES14 had an average
overburden greater than 400 Ω.m2, these results suggest that the
aquifers are highly permeable to fluid movement within, leading to
the possibility of enhanced migration and circulation of contaminants
in the groundwater system and that the area is generally corrosive.
Abstract: Electrical Muscle Stimulation (EMS) has been
introduced and globally gained increasing attention on its usefulness.
Continuous application of EMS may lead to the increment of muscle
mass and indirectly will increase the strength. This study can be used
as an alternative to help people especially those living a sedentary
lifestyle to improve their muscle activity without having to go
through a heavy workout session. Therefore, this study intended to
investigate the effectiveness of EMS training program in 5 weeks
interventions towards male body composition. It was a quasiexperimental
design, held at the Impulse Studio Bangsar, which
examined the effects of EMS training towards skeletal muscle mass
among the subjects. Fifteen subjects (n = 15) were selected to assist
in this study. The demographic data showed that, the average age of
the subjects was 43.07 years old ± 9.90, height (173.4 cm ± 9.09) and
weight was (85.79 kg ± 18.07). Results showed that there was a
significant difference on the skeletal muscle mass (p = 0.01 < 0.05),
upper body (p = 0.01 < 0.05) and lower body (p = 0.00 < 0.05).
Therefore, the null hypothesis has been rejected in this study. As a
conclusion, the application of EMS towards body composition can
increase the muscle size and strength. This method has been proven
to be able to improve athlete strength and thus, may be implemented
in the sports science area of knowledge.
Abstract: Sweep frequency response analysis has been turning
out a powerful tool for investigation of mechanical as well as
electrical integration of transformers. In this paper various aspect of
practical application of SFRA has been studied. Open circuit and
short circuit measurement were done on different phases of high
voltage and low voltage winding. A case study was presented for the
transformer of rating 31.5 MVA for various frequency ranges. A
clear picture was presented for sub- frequency ranges for HV as well
as LV winding. The main motive of work is to investigate high
voltage short circuit response. The theoretical concept about SFRA
responses is validated with expert system software results.
Abstract: The use of solar energy as a source for pumping water
is one of the promising areas in the photovoltaic (PV) application.
The energy of photovoltaic pumping systems (PVPS) can be widely
improved by employing an MPPT algorithm. This will lead
consequently to maximize the electrical motor speed of the system.
This paper presents a modified incremental conductance (IncCond)
MPPT algorithm with direct control method applied to a standalone
PV pumping system. The influence of the algorithm parameters on
system behavior is investigated and compared with the traditional
(INC) method. The studied system consists of a PV panel, a DC-DC
boost converter, and a PMDC motor-pump. The simulation of the
system by MATLAB-SIMULINK is carried out. Simulation results
found are satisfactory.
Abstract: The use of magnesium alloys is limited due to their
susceptibility to corrosion although they have many attractive
physical and mechanical properties. To increase mechanical and
corrosion properties of these alloys, many deposition method and
coating types are used. Electroless Ni–B coatings have received
considerable interest recently due to its unique properties such as
cost-effectiveness, thickness uniformity, good wear resistance,
lubricity, good ductility and corrosion resistance, excellent
solderability and electrical properties and antibacterial property. In
this study, electroless Ni-B coating could been deposited on AZ91
magnesium alloy. The obtained coating exhibited a harder and
rougher structure than the substrate.