Abstract: Sarkhoon gas plant, located in south of Iran, has been installed to removal H2S contained in a high pressure natural gas stream. The solvent used for the H2S removal from gaseous stream is 34% by weight (wt%) Di-ethanol amine (DEA) solutions. Due to increasing concentration of heat stable salt (HSS) in solvent, corrosivity of amine solution had been increased. Reports indicated that there was corrosion on the shell of regeneration column. Because source formation of HSS was unknown, we decided to control the amount of HSS at the limit less than 3% wt amine solvent. Therefore, two small columns were filled by strong anionic base and carbon active, and then polluted amine was passed through beds. Finally a temporary amine recovery package on industrial scale was made based on laboratory’s results. From economical point of view we could save $700000 beside corrosion occurrence of the stripping column has been vigorously decreased.
Abstract: In this study, multiwall carbon nanotubes (MWNTs)
were modified with nitric acid chemically and by dielectric barrier
discharge (DBD) plasma in an oxygen-based atmosphere. Used
carbon nanotubes (CNTs) were prepared by chemical vapour
deposition (CVD) floating catalyst method. For removing amorphous
carbon and metal catalyst, MWNTs were exposed to dry air and
washed with hydrochloric acid. Heating purified CNTs under helium
atmosphere caused elimination of acidic functional groups. Fourier
transformed infrared spectroscopy (FTIR) shows formation of
oxygen containing groups such as C=O and COOH. Brunauer,
Emmett, Teller (BET) analysis revealed that functionalization causes
generation of defects on the sidewalls and opening of the ends of
CNTs. Results of temperature-programmed desorption (TPD) and gas
chromatography(GC) indicate that nitric acid treatment create more
acidic groups than plasma treatment.
Abstract: Pabdeh shaly formation (Paleocene-Oligomiocene)
has been expanded in Fars, Khozestan and Lorestan. The lower
lithostratigraphic limit of this formation in Shiraz area is
distinguished from Gurpi formation by purple shale. Its upper limit is
gradational and conformable with Asmari formation. In order to
study sequence stratigraphy and microfacies of Pabdeh formation in
Shiraz area, one stratigraphic section have been chosen (Zanjiran
section). Petrographic studies resulted in the identification of 9
pelagic and calciturbidite microfacies. The calciturbidite microfacies
have been formed when the sea level was high, the rate of carbonate
deposition was high and it slumped into the deep marine. Sequence
stratigraphy studies show that Pabdeh formation in the studied zone
consists of two depositional sequences (DS) that the lower contact is
erosional (purple shale - type one, SBI or type two, SB2) and the
upper contact is correlative conformity (type two, SB2).
Abstract: The issue of unintentional islanding in PV grid
interconnection still remains as a challenge in grid-connected
photovoltaic (PV) systems. This paper discusses the overview of
popularly used anti-islanding detection methods, practically applied
in PV grid-connected systems. Anti-islanding methods generally can
be classified into four major groups, which include passive methods,
active methods, hybrid methods and communication base methods.
Active methods have been the preferred detection technique over the
years due to very small non-detected zone (NDZ) in small scale
distribution generation. Passive method is comparatively simpler
than active method in terms of circuitry and operations. However, it
suffers from large NDZ that significantly reduces its performance.
Communication base methods inherit the advantages of active and
passive methods with reduced drawbacks. Hybrid method which
evolved from the combination of both active and passive methods
has been proven to achieve accurate anti-islanding detection by many
researchers. For each of the studied anti-islanding methods, the
operation analysis is described while the advantages and
disadvantages are compared and discussed. It is difficult to pinpoint a
generic method for a specific application, because most of the
methods discussed are governed by the nature of application and
system dependent elements. This study concludes that the setup and
operation cost is the vital factor for anti-islanding method selection in
order to achieve minimal compromising between cost and system
quality.
Abstract: This paper presents a simplified version of Data Envelopment Analysis (DEA) - a conventional approach to evaluating the performance and ranking of competitive objects characterized by two groups of factors acting in opposite directions: inputs and outputs. DEA with a Perfect Object (DEA PO) augments the group of actual objects with a virtual Perfect Object - the one having greatest outputs and smallest inputs. It allows for obtaining an explicit analytical solution and making a step to an absolute efficiency. This paper develops this approach further and introduces a DEA model with Partially Perfect Objects. DEA PPO consecutively eliminates the smallest relative inputs or greatest relative outputs, and applies DEA PO to the reduced collections of indicators. The partial efficiency scores are combined to get the weighted efficiency score. The computational scheme remains simple, like that of DEA PO, but the advantage of the DEA PPO is taking into account all of the inputs and outputs for each actual object. Firm evaluation is considered as an example.
Abstract: A conventional binding method for low power in a
high-level synthesis mainly focuses on finding an optimal binding for
an assumed input data, and obtains only one binding table. In this
paper, we show that a binding method which uses multiple binding
tables gets better solution compared with the conventional methods
which use a single binding table, and propose a dynamic bus binding
scheme for low power using multiple binding tables. The proposed
method finds multiple binding tables for the proper partitions of an
input data, and switches binding tables dynamically to produce the
minimum total switching activity. Experimental result shows that the
proposed method obtains a binding solution having 12.6-28.9%
smaller total switching activity compared with the conventional
methods.
Abstract: Electrospinning is a broadly used technology to obtain
polymeric nanofibers ranging from several micrometers down to
several hundred nanometers for a wide range of applications. It offers
unique capabilities to produce nanofibers with controllable porous
structure. With smaller pores and higher surface area than regular
fibers, electrospun fibers have been successfully applied in various
fields, such as, nanocatalysis, tissue engineering scaffolds, protective
clothing, filtration, biomedical, pharmaceutical, optical electronics,
healthcare, biotechnology, defense and security, and environmental
engineering. In this study, polyurethane nanofibers were obtained
under different electrospinning parameters. Fiber morphology and
diameter distribution were investigated in order to understand them
as a function of process parameters.
Abstract: Reconfigurable optical add/drop multiplexers
(ROADMs) can be classified into three categories based on their
underlying switching technologies. Category I consists of a single
large optical switch; category II is composed of a number of small
optical switches aligned in parallel; and category III has a single
optical switch and only one wavelength being added/dropped. In this
paper, to evaluate the wavelength-routing capability of ROADMs of
category-II in dynamic optical networks,the dynamic traffic models
are designed based on Bernoulli, Poisson distributions for smooth
and regular types of traffic. Through Analytical and Simulation
results, the routing power of cat-II of ROADM networks for two
traffic models are determined.
Abstract: Foundation of tower crane serves to ensure stability
against vertical and horizontal forces. If foundation stress is not
sufficient, tower crane may be subject to overturning, shearing or
foundation settlement. Therefore, engineering review of stable support
is a highly critical part of foundation design. However, there are not
many professionals who can conduct engineering review of tower
crane foundation and, if any, they have information only on a small
number of cranes in which they have hands-on experience. It is also
customary to rely on empirical knowledge and tower crane renter-s
recommendations rather than designing foundation on the basis of
engineering knowledge. Therefore, a foundation design automation
system considering not only lifting conditions but also overturning
risk, shearing and vertical force may facilitate production of foolproof
foundation design for experts and enable even non-experts to utilize
professional knowledge that only experts can access now. This study
proposes Automatic Design Algorithm for the Tower Crane
Foundations considering load and horizontal force.
Abstract: Different numerical methods are employed and developed for simulating interfacial flows. A large range of applications belong to this group, e.g. two-phase flows of air bubbles in water or water drops in air. In such problems surface tension effects often play a dominant role. In this paper, various models of surface tension force for interfacial flows, the CSF, CSS, PCIL and SGIP models have been applied to simulate the motion of small air bubbles in water and the results were compared and reviewed. It has been pointed out that by using SGIP or PCIL models, we are able to simulate bubble rise and obtain results in close agreement with the experimental data.
Abstract: Shortening of natural resources will impose greater
limitations of electric energy consumption in various fields including
water treatment technologies. Small water treatment installations
supplied with electric energy from solar sources are perfect example of
zero-emission technology. Possibility of solar energy application, as
one of the alternative energy resources for decontamination processes
is strongly dependent on geographical location. Various examples of
solar driven water purification systems are given and design of
solar-water treatment installation based on ozone for the geographical
conditions in Poland are presented.
Abstract: Green Forestation Plan (GFP) was expected to promote the reforestation of plains totaling 60,000 has within the first 8 years. Annual subsidies were budgeted at $120,000 per ha, and $2.4 million for 20 years. In this research we have surveyed landlords- opinions toward the GFP in an attempt to understand landlords- incentives for participating in the GFP and their levels of concern and agreement toward the policy design. Based our analysis of landlords- opinions on the policy design, we expect to derive appropriate complementary measures, establish effective promotional schemes, and raise the policy effectiveness of the GFP. According to the results of this research, there was still a relatively high proportion of population who were not aware of GFP; more than 50% of landlords were neutral or willing to participate given high reforestation subsidies; approximately 30% of landlords were unwilling to participate. In terms of the designs of GFP, more than 50% of respondents were concerned and agreed with the policy design. In terms of the period of this policy, 52.7% of respondents indicated that it should be shortened to 15 years or lower. In terms of the amount of the subsidy, 41.7% of respondents showed that it should be raised to approximately $250,000/ha. In terms of land area restrictions, 88.0% of respondents believed that the minimum should be lowered to 0.4 ha. More than 70% of respondents owned less than 0.4 has of land, and since they do not own enough land to be eligible for the program, more than 80% of landlords wished to lower the minimum requirements of land area. In addition, 59.3% of respondents were reluctant to participate in reforestation because their lands were too small to be eligible; 15.0% of respondents were reluctant because the duration was too long. Responses to the question about “how the policy can be adjusted to provide incentives for landlords- participation" revealed that almost 40% of respondents desired higher subsidies. Some policy suggestions are provided as follows: (1) many landlords are still unaware of the GFP so the government should enhance the promotion of the policy; (2) many landlords are unwilling to participate in GFP mainly because they do not own enough lands to be eligible, hence the government should consider adjusting its requirements for minimum agricultural land area; (3) for subsequent promotions on GFP, the government may consider targeting on the landlords with high income and high level of education; (4) because the subsidy of this policy alone provides limited help to landlords, the government should help the landlords to explore other revenue possibilities from afforestation in addition to the existing subsidies and raise the participation incentives.
Abstract: The present study aims to explore the role of parents'
ethnic socialization practices contributes to the ethnic identity
development, self-esteem and psychological adjustment of multi
ethnic children in Sabah, Malaysia. A total of 342 multi ethnic
children (age range = 10 years old to 14 years old; mean age = 12.65
years, SD = 0.88) and their parents participated in the present study.
The modified version of Multi group Ethnic Identity Measure
(MEIM), The Familial Ethnic Socialization Measure (FESM). The
Rosenberg Self-Esteem Scale (RSE) and Behavioral and Emotional
Rating Scale Edition 2 (BERS-2) were used in this study. The results
showed that: i) parents' ethnic socialization practice was a strong
predictor of ethnic identity development of multi ethnic children; ii)
parents' ethnic socialization practice also was a significant predictor
of self-esteem of multi ethnic children; iii) parents' ethnic
socialization practice was not a significant predictor of psychological
adjustment of multi ethnic children. The results of this study showed
the implications parents' ethnic socialization practices and ethnic
identity development in successful multi ethnic families.
Abstract: This research proposes an algorithm for the simulation
of time-periodic unsteady problems via the solution unsteady Euler
and Navier-Stokes equations. This algorithm which is called Time
Spectral method uses a Fourier representation in time and hence
solve for the periodic state directly without resolving transients
(which consume most of the resources in a time-accurate scheme).
Mathematical tools used here are discrete Fourier transformations. It
has shown tremendous potential for reducing the computational cost
compared to conventional time-accurate methods, by enforcing
periodicity and using Fourier representation in time, leading to
spectral accuracy. The accuracy and efficiency of this technique is
verified by Euler and Navier-Stokes calculations for pitching airfoils.
Because of flow turbulence nature, Baldwin-Lomax turbulence
model has been used at viscous flow analysis. The results presented
by the Time Spectral method are compared with experimental data. It
has shown tremendous potential for reducing the computational cost
compared to the conventional time-accurate methods, by enforcing
periodicity and using Fourier representation in time, leading to
spectral accuracy, because results verify the small number of time
intervals per pitching cycle required to capture the flow physics.
Abstract: Transportation is one of the main activities related to
creating value for the tourists. Transport management in tourism
mainly focuses on managing transfer points and vehicle capacity.
However, transport service level must also be ensured as it now
relates to tourist-s experiences. This paper emphasizes on the
responsiveness as one of key service performance measures. An
evaluation framework is developed and illustarted by using the case
of small bus service in Pattaya city. It can be seen as a great potential
for the city to utilize the small bus transportation in order to meet the
needs of more diverse group of passengers and to support the
expansion of tourist areas. The framework integrates with service
operations management, logistics, and tourism behavior perspectives.
The findings from the investigation of existing small bus service are
presented and preliminarily validate the usability of the framework.
Abstract: This paper study the segmented split capacitor
Digital-to-Analog Converter (DAC) implemented in a differentialtype
12-bit Successive Approximation Analog-to-Digital Converter
(SA-ADC). The series capacitance split array method employed as it
reduced the total area of the capacitors required for high resolution
DACs. A 12-bit regular binary array structure requires 2049 unit
capacitors (Cs) while the split array needs 127 unit Cs. These results
in the reduction of the total capacitance and power consumption of
the series split array architectures as to regular binary-weighted
structures. The paper will show the 12-bit DAC series split capacitor
with 4-bit thermometer coded DAC architectures as well as the
simulation and measured results.
Abstract: The Combination of path planning and path following is the main purpose of this paper. This paper describes the developed practical approach to motion control of the MRL small size robots. An intelligent controller is applied to control omni-directional robots motion in simulation and real environment respectively. The Brain Emotional Learning Based Intelligent Controller (BELBIC), based on LQR control is adopted for the omni-directional robots. The contribution of BELBIC in improving the control system performance is shown as application of the emotional learning in a real world problem. Optimizing of the control effort can be achieved in this method too. Next the implicit communication method is used to determine the high level strategies and coordination of the robots. Some simple rules besides using the environment as a memory to improve the coordination between agents make the robots' decision making system. With this simple algorithm our team manifests a desirable cooperation.
Abstract: A combination of image fusion and quad tree decomposition method is used for detecting the sunspot trajectories in each month and computation of the latitudes of these trajectories in each solar hemisphere. Daily solar images taken with SOHO satellite are fused for each month and the result of fused image is decomposed with Quad Tree decomposition method in order to classifying the sunspot trajectories and then to achieve the precise information about latitudes of sunspot trajectories. Also with fusion we deduce some physical remarkable conclusions about sun magnetic fields behavior. Using quad tree decomposition we give information about the region on sun surface and the space angle that tremendous flares and hot plasma gases permeate interplanetary space and attack to satellites and human technical systems. Here sunspot images in June, July and August 2001 are used for studying and give a method to compute the latitude of sunspot trajectories in each month with sunspot images.
Abstract: Cs-type nanocomposite zeolite membrane was successfully synthesized on an alumina ceramic hollow fibre with a mean outer diameter of 1.7 mm; cesium cationic exchange test was carried out inside test module with mean wall thickness of 230 μm and an average crossing pore size smaller than 0.2 μm. Separation factor of n-butane/H2 obtained indicate that a relatively high quality closed to 20. Maxwell-Stefan modeling provides an equivalent thickness lower than 1 µm. To compare the difference an application to CO2/N2 separation has been achieved, reaching separation factors close to (4,18) before and after cation exchange on H-zeolite membrane formed within the pores of a ceramic alumina substrate.
Abstract: Distant-talking voice-based HCI system suffers from
performance degradation due to mismatch between the acoustic
speech (runtime) and the acoustic model (training). Mismatch is
caused by the change in the power of the speech signal as observed at
the microphones. This change is greatly influenced by the change in
distance, affecting speech dynamics inside the room before reaching
the microphones. Moreover, as the speech signal is reflected, its
acoustical characteristic is also altered by the room properties. In
general, power mismatch due to distance is a complex problem. This
paper presents a novel approach in dealing with distance-induced
mismatch by intelligently sensing instantaneous voice power variation
and compensating model parameters. First, the distant-talking speech
signal is processed through microphone array processing, and the
corresponding distance information is extracted. Distance-sensitive
Gaussian Mixture Models (GMMs), pre-trained to capture both
speech power and room property are used to predict the optimal
distance of the speech source. Consequently, pre-computed statistic
priors corresponding to the optimal distance is selected to correct
the statistics of the generic model which was frozen during training.
Thus, model combinatorics are post-conditioned to match the power
of instantaneous speech acoustics at runtime. This results to an
improved likelihood in predicting the correct speech command at
farther distances. We experiment using real data recorded inside two
rooms. Experimental evaluation shows voice recognition performance
using our method is more robust to the change in distance compared
to the conventional approach. In our experiment, under the most
acoustically challenging environment (i.e., Room 2: 2.5 meters), our
method achieved 24.2% improvement in recognition performance
against the best-performing conventional method.