Abstract: This paper describes the design considerations of an
experimental setup for research and exploring the drives of batteryfed
electric vehicles. Effective setup composition and its components
are discussed. With experimental setup described in this paper,
durability and functional tests can be procured to the customers.
Multiple experiments are performed in the form of steady-state
system exploring, acceleration programs, multi-step tests (speed
control, torque control), load collectives or close-to-reality driving
tests (driving simulation). Main focus of the functional testing is on
the measurements of power and energy efficiency and investigations
in driving simulation mode, which are used for application purposes.
In order to enable the examination of the drive trains beyond
standard modes of operation, different other parameters can be
studied also.
Abstract: It is expected that ubiquitous era will come soon. A ubiquitous environment has features like peer-to-peer and nomadic environments. Such features can be represented by peer-to-peer systems and mobile ad-hoc networks (MANETs). The features of P2P systems and MANETs are similar, appealing for implementing P2P systems in MANET environment. It has been shown that, however, the performance of the P2P systems designed for wired networks do not perform satisfactorily in mobile ad-hoc environment. Subsequently, this paper proposes a method to improve P2P performance using cross-layer design and the goodness of a node as a peer. The proposed method uses routing metric as well as P2P metric to choose favorable peers to connect. It also utilizes proactive approach for distributing peer information. According to the simulation results, the proposed method provides higher query success rate, shorter query response time and less energy consumption by constructing an efficient overlay network.
Abstract: This paper presents the experimental results of silicone rubber housing material for 24kV lightning arrester under artificial accelerated ageing test based on IEC 61109 specifications. Specimens having inclined and alternated shed made of HTV silicone rubber with ATH content and having leakage distance 625 mm were tested continuously 1000 hrs in artificial salt fog chamber. After 1000 hrs of salt fog ageing test, obviously surface erosion was observed on trunk between the upper large shed and the lower small shed near the energized end. Decreasing in hydrophobicity and increasing in hardness were measured on tested specimen comparing with new specimen. Chemical analysis by ATR-FTIR confirmed the observation results.
Abstract: The main objective of this paper is a comparative
investigate in enhancement of damping power system oscillation via
coordinated design of the power system stabilizer (PSS) and static
synchronous series compensator (SSSC) and static synchronous
compensator (STATCOM). The design problem of FACTS-based
stabilizers is formulated as a GA based optimization problem. In this
paper eigenvalue analysis method is used on small signal stability of
single machine infinite bus (SMIB) system installed with SSSC and
STATCOM. The generator is equipped with a PSS. The proposed
stabilizers are tested on a weakly connected power system with
different disturbances and loading conditions. This aim is to enhance
both rotor angle and power system stability. The eigenvalue analysis
and non-linear simulation results are presented to show the effects of
these FACTS-based stabilizers and reveal that SSSC exhibits the best
effectiveness on damping power system oscillation.
Abstract: In this work the design and characterization of an optoelectronic automated measurement system it is presented. The optoelectronic devices of this system are an optical transmitter, the optical components and the optical receiver, which were selected for a great precision of the system. The mechanical system allows free displacement of the components as well as the devices that generate the movement. The results, length and profile of the objects are display in Lab View.
Abstract: This paper presents the experimental results of
comparison between leakage currents and discharge currents. The leakage currents were obtained on polluted porcelain insulator.
Whereas, the discharge currents were obtained on lightly artificial
polluted porcelain specimen. The conducted measurements were
leakage current or discharge current and applied voltage. The insulator or specimen was in a hermetically sealed chamber, and the
current waveforms were analyzed using FFT.
The result indicated that the leakage current (LC) on low RH condition the fifth harmonic would be visible, and followed by the
seventh harmonic. The insulator had capacitive property. Otherwise,
on 99% relative humidity, the fifth harmonic would also be visible,
and the phase angle reached up to 12.2 degree. Whereas, on discharge current, the third harmonic would be visible, and followed
by fifth harmonic. The third harmonic would increase as pressure reduced. On this condition, the specimen had a non-linear characteristics
Abstract: Properly sized capacitor banks are connected across induction motors for several reasons including power factor correction, reducing distortions, increasing capacity, etc. Total harmonic distortion (THD) and power factor (PF) are used in such cases to quantify the improvements obtained through connection of the external capacitor banks. On the other hand, one of the methods for assessing the motor internal condition is by the use of Park-s pattern analysis. In spite of taking adequate precautionary measures, the capacitor banks may sometimes malfunction. Such a minor fault in the capacitor bank is often not apparently discernible. This may however, give rise to substantial degradation of power factor correction performance and may also damage the supply profile. The case is more severe with the fact that the Park-s pattern gets distorted due to such external capacitor faults, and can give anomalous results about motor internal fault analyses. The aim of this paper is to present simulation and hardware laboratory test results to have an understanding of the anomalies in harmonic distortion and Park-s pattern analyses in induction motors due to capacitor bank defects.
Abstract: Virtually all existing networked system management
tools use a Manager/Agent paradigm. That is, distributed agents are
deployed on managed devices to collect local information and report
it back to some management unit. Even those that use standard
protocols such as SNMP fall into this model. Using standard protocol
has the advantage of interoperability among devices from different
vendors. However, it may not be able to provide customized
information that is of interest to satisfy specific management needs.
In this dissertation work, different approaches are used to
collect information regarding the devices attached to a Local Area
Network. An SNMP aware application is being developed that will
manage the discovery procedure and will be used as data collector.
Abstract: In this paper a three dimensional thermal model of a
sliding contact system is proposed for both steady-state or transient
conditions. The influence of contact force, electric current and
ambient temperature on the temperature distribution, has been
investigated. A thermal analysis of the different type of the graphite
material of fixed electric contact and its influence on contact system
temperature rise, has been performed. To validate the three
dimensional thermal model, some experimental tests have been done.
There is a good correlation between experimental and simulation
results.
Abstract: the cursive nature of the Arabic writing makes it
difficult to accurately segment characters or even deal with the whole
word efficiently. Therefore, in this paper, a printed Arabic sub-word
recognition system is proposed. The suggested algorithm utilizes
geometrical moments as descriptors for the separated sub-words.
Three types of moments are investigated and applied to the printed
sub-word images after dividing each image into multiple parts using
windowing. Since moments are global descriptors, the windowing
mechanism allows the moments to be applied to local regions of the
sub-word. The local-global mixture of the proposed scheme increases
the discrimination power of the moments while keeping the
simplicity and ease of use of moments.
Abstract: Memory Errors Detection and Correction aim to secure the transaction of data between the central processing unit of a satellite onboard computer and its local memory. In this paper, the application of a double-bit error detection and correction method is described and implemented in Field Programmable Gate Array (FPGA) technology. The performance of the proposed EDAC method is measured and compared with two different EDAC devices, using the same FPGA technology. Statistical analysis of single-event upset (SEU) and multiple-bit upset (MBU) activity in commercial memories onboard the first Algerian microsatellite Alsat-1 is given.
Abstract: The electrical and structural properties of Hf/Al/Ni/Au
(20/100/25/50 nm) ohmic contact to n-GaN are reported in this study.
Specific contact resistivities of Hf/Al/Ni/Au based contacts have been
investigated as a function of annealing temperature and achieve the
lowest value of 1.09´10-6 Ω·cm2 after annealing at 650 oC in vacuum.
A detailed mechanism of ohmic contact formation is discussed. By
using different chemical analyses, it is anticipated that the formation of
Hf-Al-N alloy might be responsible to form low temperature ohmic
contacts for the Hf-based scheme to n-GaN.
Abstract: Electrical distribution systems are incurring large losses as the loads are wide spread, inadequate reactive power compensation facilities and their improper control. A comprehensive static VAR compensator consisting of capacitor bank in five binary sequential steps in conjunction with a thyristor controlled reactor of smallest step size is employed in the investigative work. The work deals with the performance evaluation through analytical studies and practical implementation on an existing system. A fast acting error adaptive controller is developed suitable both for contactor and thyristor switched capacitors. The switching operations achieved are transient free, practically no need to provide inrush current limiting reactors, TCR size minimum providing small percentages of nontriplen harmonics, facilitates stepless variation of reactive power depending on load requirement so as maintain power factor near unity always. It is elegant, closed loop microcontroller system having the features of self regulation in adaptive mode for automatic adjustment. It is successfully tested on a distribution transformer of three phase 50 Hz, Dy11, 11KV/440V, 125 KVA capacity and the functional feasibility and technical soundness are established. The controller developed is new, adaptable to both LT & HT systems and practically established to be giving reliable performance.
Abstract: In the power quality analysis non-stationary nature
of voltage distortions require some precise and powerful analytical
techniques. The time-frequency representation (TFR) provides a
powerful method for identification of the non-stationary of the
signals. This paper investigates a comparative study on two
techniques for analysis and visualization of voltage distortions with
time-varying amplitudes. The techniques include the Discrete
Wavelet Transform (DWT), and the S-Transform. Several power
quality problems are analyzed using both the discrete wavelet
transform and S–transform, showing clearly the advantage of the S–
transform in detecting, localizing, and classifying the power quality
problems.
Abstract: This paper presents a new feature based dense stereo
matching algorithm to obtain the dense disparity map via dynamic
programming. After extraction of some proper features, we use some
matching constraints such as epipolar line, disparity limit, ordering
and limit of directional derivative of disparity as well. Also, a coarseto-
fine multiresolution strategy is used to decrease the search space
and therefore increase the accuracy and processing speed. The
proposed method links the detected feature points into the chains and
compares some of the feature points from different chains, to
increase the matching speed. We also employ color stereo matching
to increase the accuracy of the algorithm. Then after feature
matching, we use the dynamic programming to obtain the dense
disparity map. It differs from the classical DP methods in the stereo
vision, since it employs sparse disparity map obtained from the
feature based matching stage. The DP is also performed further on a
scan line, between any matched two feature points on that scan line.
Thus our algorithm is truly an optimization method. Our algorithm
offers a good trade off in terms of accuracy and computational
efficiency. Regarding the results of our experiments, the proposed
algorithm increases the accuracy from 20 to 70%, and reduces the
running time of the algorithm almost 70%.
Abstract: with increasing circuits- complexity and demand to
use portable devices, power consumption is one of the most
important parameters these days. Full adders are the basic block of
many circuits. Therefore reducing power consumption in full adders
is very important in low power circuits. One of the most powerconsuming
modules in full adders is XOR/XNOR circuit. This paper
presents two new full adders based on two new logic approaches. The
proposed logic approaches use one XOR or XNOR gate to implement
a full adder cell. Therefore, delay and power will be decreased. Using
two new approaches and two XOR and XNOR gates, two new full
adders have been implemented in this paper. Simulations are carried
out by HSPICE in 0.18μm bulk technology with 1.8V supply voltage.
The results show that the ten-transistors proposed full adder has 12%
less power consumption and is 5% faster in comparison to MB12T
full adder. 9T is more efficient in area and is 24% better than similar
10T full adder in term of power consumption. The main drawback of
the proposed circuits is output threshold loss problem.
Abstract: This paper presents reliability evaluation techniques
which are applied in distribution system planning studies and
operation. Reliability of distribution systems is an important issue in
power engineering for both utilities and customers. Reliability is a
key issue in the design and operation of electric power distribution
systems and load. Reliability evaluation of distribution systems has
been the subject of many recent papers and the modeling and
evaluation techniques have improved considerably.
Abstract: This document details the process of developing a
wireless device that captures the basic movements of the foot (plantar
flexion, dorsal flexion, abduction, adduction.), and the knee
movement (flexion). It implements a motion capture system by using
a hardware based on optical fiber sensors, due to the advantages in
terms of scope, noise immunity and speed of data transmission and
reception. The operating principle used by this system is the detection
and transmission of joint movement by mechanical elements and
their respective measurement by optical ones (in this case infrared).
Likewise, Visual Basic software is used for reception, analysis and
signal processing of data acquired by the device, generating a 3D
graphical representation in real time of each movement. The result is
a boot in charge of capturing the movement, a transmission module
(Implementing Xbee Technology) and a receiver module for
receiving information and sending it to the PC for their respective
processing.
The main idea with this device is to help on topics such as
bioengineering and medicine, by helping to improve the quality of
life and movement analysis.
Abstract: The RR interval series is non-stationary and unevenly
spaced in time. For estimating its power spectral density (PSD) using
traditional techniques like FFT, require resampling at uniform
intervals. The researchers have used different interpolation
techniques as resampling methods. All these resampling methods
introduce the low pass filtering effect in the power spectrum. The
lomb transform is a means of obtaining PSD estimates directly from
irregularly sampled RR interval series, thus avoiding resampling. In
this work, the superiority of Lomb transform method has been
established over FFT based approach, after applying linear and
cubicspline interpolation as resampling methods, in terms of
reproduction of exact frequency locations as well as the relative
magnitudes of each spectral component.
Abstract: Since the one-to-one word translator does not have the
facility to translate pragmatic aspects of Javanese, the parallel text
alignment model described uses a phrase pair combination. The
algorithm aligns the parallel text automatically from the beginning to
the end of each sentence. Even though the results of the phrase pair
combination outperform the previous algorithm, it is still inefficient.
Recording all possible combinations consume more space in the
database and time consuming. The original algorithm is modified by
applying the edit distance coefficient to improve the data-storage
efficiency. As a result, the data-storage consumption is 90% reduced
as well as its learning period (42s).