Abstract: This paper discusses the novel graphical approach for
stability analysis of multi induction motor drive controlled by a single
inverter. Stability issue arises in parallel connected induction motors
under unbalanced load conditions. The two powerful globally
accepted modeling and simulation software packages such as
MATLAB and LabVIEW are selected to perform the stability
analysis. The stability investigation is performed for different load
conditions and difference in stator and rotor resistances among the
two motors. It is very simple and effective than the techniques
presented to obtain the stability of the parallel connected induction
motor drive under unbalanced load conditions. Approximate transfer
functions are considered to model the induction motors, load
dynamics, speed controllers and inverter. Simulink library tools are
utilized to model the entire drive scheme in MATLAB. Stability
study is discussed in LabVIEW using control design and simulation
toolkits. Simulation results are illustrated for various running
conditions to demonstrate the effectiveness of the transfer function
method.
Abstract: Electromyography (EMG) is the study of muscles function through analysis of electrical activity produced from muscles. This electrical activity which is displayed in the form of signal is the result of neuromuscular activation associated with muscle contraction. The most common techniques of EMG signal recording are by using surface and needle/wire electrode where the latter is usually used for interest in deep muscle. This paper will focus on surface electromyogram (SEMG) signal. During SEMG recording, several problems had to been countered such as noise, motion artifact and signal instability. Thus, various signal processing techniques had been implemented to produce a reliable signal for analysis. SEMG signal finds broad application particularly in biomedical field. It had been analyzed and studied for various interests such as neuromuscular disease, enhancement of muscular function and human-computer interface.
Abstract: The identification and elimination of bad
measurements is one of the basic functions of a robust state estimator
as bad data have the effect of corrupting the results of state
estimation according to the popular weighted least squares method.
However this is a difficult problem to handle especially when dealing
with multiple errors from the interactive conforming type. In this
paper, a self adaptive genetic based algorithm is proposed. The
algorithm utilizes the results of the classical linearized normal
residuals approach to tune the genetic operators thus instead of
making a randomized search throughout the whole search space it is
more likely to be a directed search thus the optimum solution is
obtained at very early stages(maximum of 5 generations). The
algorithm utilizes the accumulating databases of already computed
cases to reduce the computational burden to minimum. Tests are
conducted with reference to the standard IEEE test systems. Test
results are very promising.
Abstract: Nowadays the control of stator voltage at a constant frequency is one of the traditional and low expense methods in order to control the speed of induction motors near its nominal speed. The torque of induction motor is a nonlinear function of the firing angle, phase angle and speed. In this paper the speed control of induction motor regarding various load torque and under different conditions will be investigated based on a fuzzy controller with inverse training.
Abstract: This paper explores steady-state characteristics of
grid-connected doubly fed induction motor (DFIM) in case of unity
power factor operation. Based on the synchronized mathematical
model, analytic determination of the control laws is presented and
illustrated by various figures to understand the effect of the applied
rotor voltage on the speed and the active power. On other hand,
unlike previous works where the stator resistance was neglected, in
this work, stator resistance is included such that the equations can be
applied to small wind turbine generators which are becoming more
popular. Finally the work is crowned by integration of the studied
induction generator in a wind system where an open loop control is
proposed confers a remarkable simplicity of implementation
compared to the known methods.
Abstract: The numerous qualities of squirrel cage induction
machines enhance their use in industry. However, various faults can
occur, such as stator short-circuits and rotor failures.
In this paper, we use a technique based on the spectral analysis of
stator current in order to detect the fault in the machine: broken rotor
bars. Thus, the number effect of the breaks has been highlighted. The
effect is highlighted by considering the machine controlled by the
Direct Torque Control (DTC). The key to fault detection is the
development of a simplified dynamic model of a squirrel cage
induction motor taking account the broken bars fault and the stator
current spectrum analysis (FFT).
Abstract: A robust wheel slip controller for electric vehicles is
introduced. The proposed wheel slip controller exploits the dynamics
of electric traction drives and conventional hydraulic brakes for
achieving maximum energy efficiency and driving safety. Due to
the control of single wheel traction motors in combination with a
hydraulic braking system, it can be shown, that energy recuperation
and vehicle stability control can be realized simultaneously. The
derivation of a sliding mode wheel slip controller accessing two
drivetrain actuators is outlined and a comparison to a conventionally
braked vehicle is shown by means of simulation.
Abstract: The main objective of Automatic Generation Control (AGC) is to balance the total system generation against system load losses so that the desired frequency and power interchange with neighboring systems is maintained. Any mismatch between generation and demand causes the system frequency to deviate from its nominal value. Thus high frequency deviation may lead to system collapse. This necessitates a very fast and accurate controller to maintain the nominal system frequency. This paper deals with a novel approach of artificial intelligence (AI) technique called Hybrid Neuro-Fuzzy (HNF) approach for an (AGC). The advantage of this controller is that it can handle the non-linearities at the same time it is faster than other conventional controllers. The effectiveness of the proposed controller in increasing the damping of local and inter area modes of oscillation is demonstrated in a two area interconnected power system. The result shows that intelligent controller is having improved dynamic response and at the same time faster than conventional controller.
Abstract: This paper presents the design and analysis of a parallel
connected inverter configuration of. The configuration consists of
parallel connected three-phase dc/ac inverter. Series resistors added
to the inverter output to maintain same current in each inverter of the
two parallel inverters, and to reduce the circulating current in the
parallel inverters to the minimum. High frequency third harmonic
injection PWM (THIPWM) employed to reduce the total harmonic
distortion and to make maximum use of the voltage source. DSP was
used to generate the THIPWM and the control algorithm for the
converter. Selected experimental results have been shown to validate
the proposed system.
Abstract: Introducing Electromagnetic Interference and Electromagnetic Compatibility, or “The Art of Black Magic", for engineering students might be a terrifying experience both for students and tutors. Removing the obstacle of large, expensive facilities like a fully fitted EMC laboratory and hours of complex theory, this paper demonstrates a design of a laboratory setup for student exercises, giving students experience in the basics of EMC/EMI problems that may challenge the functionality and stability of embedded system designs. This is done using a simple laboratory installation and basic measurement equipment such as a medium cost digital storage oscilloscope, at the cost of not knowing the exact magnitude of the noise components, but rather if the noise is significant or not, as well as the source of the noise. A group of students have performed a trial exercise with good results and feedback.
Abstract: Static Var Compensator (SVC) is a shunt type FACTS
device which is used in power system primarily for the purpose of
voltage and reactive power control. In this paper, a fuzzy logic based
supplementary controller for Static Var Compensator (SVC) is
developed which is used for damping the rotor angle oscillations and
to improve the transient stability of the power system. Generator
speed and the electrical power are chosen as input signals for the
Fuzzy Logic Controller (FLC). The effectiveness and feasibility of
the proposed control is demonstrated with Single Machine Infinite
Bus (SMIB) system and multimachine system (WSCC System)
which show improvement over the use of a fixed parameter
controller.
Abstract: High Voltage (HV) transmission lines are widely
spread around residential places. They take all forms of shapes:
concrete, steel, and timber poles. Earth grid always form part of the
HV transmission structure, whereat soil resistivity value is one of the
main inputs when it comes to determining the earth grid
requirements. In this paper, the soil structure and its implication on
the electrode resistance of HV transmission poles will be explored. In
Addition, this paper will present simulation for various soil structures
using IEEE and Australian standards to verify the computation with
CDEGS software. Furthermore, the split factor behavior under
different soil resistivity structure will be presented using CDEGS
simulations.
Abstract: In this paper a unified approach via block-pulse functions (BPFs) or shifted Legendre polynomials (SLPs) is presented to solve the linear-quadratic-Gaussian (LQG) control problem. Also a recursive algorithm is proposed to solve the above problem via BPFs. By using the elegant operational properties of orthogonal functions (BPFs or SLPs) these computationally attractive algorithms are developed. To demonstrate the validity of the proposed approaches a numerical example is included.
Abstract: Fuel cell's system requires regulating circuit for
voltage and current in order to control power in case of connecting to
other generative devices or load. In this paper Fuel cell system and
convertor, which is a multi-variable system, are controlled using
sliding mode method. Use of weighting matrix in design procedure
made it possible to regulate speed of control. Simulation results show
the robustness and accuracy of proposed controller for controlling
desired of outputs.
Abstract: A new fuzzy filter is presented for noise reduction of
images corrupted with additive noise. The filter consists of two
stages. In the first stage, all the pixels of image are processed for
determining noisy pixels. For this, a fuzzy rule based system
associates a degree to each pixel. The degree of a pixel is a real
number in the range [0,1], which denotes a probability that the pixel
is not considered as a noisy pixel. In the second stage, another fuzzy
rule based system is employed. It uses the output of the previous
fuzzy system to perform fuzzy smoothing by weighting the
contributions of neighboring pixel values. Experimental results are
obtained to show the feasibility of the proposed filter. These results
are also compared to other filters by numerical measure and visual
inspection.
Abstract: This article proposes a voltage-mode
multifunction filter using differential voltage current
controllable current conveyor transconductance amplifier
(DV-CCCCTA). The features of the circuit are that: the
quality factor and pole frequency can be tuned independently
via the values of capacitors: the circuit description is very
simple, consisting of merely 1 DV-CCCCTA, and 2
capacitors. Without any component matching conditions, the
proposed circuit is very appropriate to further develop into
an integrated circuit. Additionally, each function response
can be selected by suitably selecting input signals with
digital method. The PSpice simulation results are depicted.
The given results agree well with the theoretical anticipation.
Abstract: Corner detection and optical flow are common techniques for feature-based video stabilization. However, these algorithms are computationally expensive and should be performed at a reasonable rate. This paper presents an algorithm for discarding irrelevant feature points and maintaining them for future use so as to improve the computational cost. The algorithm starts by initializing a maintained set. The feature points in the maintained set are examined against its accuracy for modeling. Corner detection is required only when the feature points are insufficiently accurate for future modeling. Then, optical flows are computed from the maintained feature points toward the consecutive frame. After that, a motion model is estimated based on the simplified affine motion model and least square method, with outliers belonging to moving objects presented. Studentized residuals are used to eliminate such outliers. The model estimation and elimination processes repeat until no more outliers are identified. Finally, the entire algorithm repeats along the video sequence with the points remaining from the previous iteration used as the maintained set. As a practical application, an efficient video stabilization can be achieved by exploiting the computed motion models. Our study shows that the number of times corner detection needs to perform is greatly reduced, thus significantly improving the computational cost. Moreover, optical flow vectors are computed for only the maintained feature points, not for outliers, thus also reducing the computational cost. In addition, the feature points after reduction can sufficiently be used for background objects tracking as demonstrated in the simple video stabilizer based on our proposed algorithm.
Abstract: Optimal capacitor allocation in distribution systems
has been studied for a long times. It is an optimization problem
which has an objective to define the optimal sizes and locations of
capacitors to be installed. In this works, an overview of capacitor
placement problem in distribution systems is briefly introduced. The
objective functions and constraints of the problem are listed and the
methodologies for solving the problem are summarized.
Abstract: The main objectif of this paper is to present a tool that
we have developed subject to characterize and modelling indoor radio
channel propagation at millimetric wave. The tool is based on the
ray tracing technique (RTT). As, in realistic environment we cannot
neglect the significant impact of Human Body Shadowing and other
objects in motion on indoor 60 GHz propagation channel. Hence,
our proposed model allows a simulation of propagation in a dynamic
indoor environment. First, we describe a model of human body.
Second, RTT with this model is used to simulate the propagation
of millimeter waves in the presence of persons in motion. Results
of the simulation show that this tool gives results in agreement with
those reported in the literature. Specially, the effects of people motion
on temporal channel properties.
Abstract: Organization of video databases is becoming difficult
task as the amount of video content increases. Video classification
based on the content of videos can significantly increase the speed of
tasks such as browsing and searching for a particular video in a
database. In this paper, a content-based videos classification system
for the classes indoor and outdoor is presented. The system is
intended to be used on a mobile platform with modest resources. The
algorithm makes use of the temporal redundancy in videos, which
allows using an uncomplicated classification model while still
achieving reasonable accuracy. The training and evaluation was done
on a video database of 443 videos downloaded from a video sharing
service. A total accuracy of 87.36% was achieved.