Abstract: To reflect the influence of after-treatment system retrofit and natural gas-fueled vehicle replace on exhaust emissions emitted by urban buses, a portable emission measurement system (PEMS) was employed herein to conduct real driving emission measurements. This study investigated the differences in particle number (PN), particle mass (PM), and nitrogen oxides (NOx) emissions from a China IV diesel bus retrofitted by catalyzed diesel particulate filter (CDPF), a China IV diesel bus, and a China V natural gas bus. The results show that both tested diesel buses possess markedly advantages in NOx emission control when compared to the lean-burn natural gas bus equipped without any NOx after-treatment system. As to PN and PM, only the DOC+CDPF retrofitting diesel bus exhibits enormous benefits on emission control related to the natural gas bus, especially the normal diesel bus. Meanwhile, the differences in PM and PN emissions between retrofitted and normal diesel buses generally increase with the increase in vehicle specific power (VSP). Furthermore, the differences in PM emissions, especially those in the higher VSP ranges, are more significant than those in PN. In addition, the maximum peak PN particle size (32 nm) of the retrofitted diesel bus was significantly lower than that of the normal diesel bus (100 nm). These phenomena indicate that the CDPF retrofitting can effectively reduce diesel bus exhaust particle emissions, especially those with large particle sizes.
Abstract: We present a decision-support tool to assist an operator in the detection and tracking of a suspect vehicle traveling to an unknown target destination. Multiple data sources, such as traffic cameras, traffic information, weather, etc., are integrated and processed in real-time to infer a suspect’s intended destination chosen from a list of pre-determined high-value targets. Previously, we presented our work in the detection and tracking of vehicles using traffic and airborne cameras. Here, we focus on the fusion and processing of that information to predict a suspect’s behavior. The network of cameras is represented by a directional graph, where the edges correspond to direct road connections between the nodes and the edge weights are proportional to the average time it takes to travel from one node to another. For our experiments, we construct our graph based on the greater Los Angeles subset of the Caltrans’s “Performance Measurement System” (PeMS) dataset. We propose a Bayesian approach where a posterior probability for each target is continuously updated based on detections of the suspect in the live video feeds. Additionally, we introduce the concept of ‘soft interventions’, inspired by the field of Causal Inference. Soft interventions are herein defined as interventions that do not immediately interfere with the suspect’s movements; rather, a soft intervention may induce the suspect into making a new decision, ultimately making their intent more transparent. For example, a soft intervention could be temporarily closing a road a few blocks from the suspect’s current location, which may require the suspect to change their current course. The objective of these interventions is to gain the maximum amount of information about the suspect’s intent in the shortest possible time. Our system currently operates in a human-on-the-loop mode where at each step, a set of recommendations are presented to the operator to aid in decision-making. In principle, the system could operate autonomously, only prompting the operator for critical decisions, allowing the system to significantly scale up to larger areas and multiple suspects. Once the intended target is identified with sufficient confidence, the vehicle is reported to the authorities to take further action. Other recommendations include a selection of road closures, i.e., soft interventions, or to continue monitoring. We evaluate the performance of the proposed system using simulated scenarios where the suspect, starting at random locations, takes a noisy shortest path to their intended target. In all scenarios, the suspect’s intended target is unknown to our system. The decision thresholds are selected to maximize the chances of determining the suspect’s intended target in the minimum amount of time and with the smallest number of interventions. We conclude by discussing the limitations of our current approach to motivate a machine learning approach, based on reinforcement learning in order to relax some of the current limiting assumptions.
Abstract: This study investigates the effects of operating parameters of different current density, temperature and pressure on the performance of a proton exchange membrane (PEM) water electrolysis stack. A 7-cell PEM water electrolysis stack was assembled and tested under different operation modules. The voltage change and polarization curves under different test conditions, namely current density, temperature and pressure, were recorded. Results show that higher temperature has positive effect on overall stack performance, where temperature of 80 ℃ improved the cell performance greatly. However, the cathode pressure and current density has little effect on stack performance.
Abstract: Background: The immune system has evolved several mechanisms to protect the host against cancer, and it has now been suggested that the expansion of its functions may prevent tumor growth and control the symptoms of cancer patients. Two techniques, ozone therapy and pulsed electromagnetic fields (PEMF), are independently associated with an increase in the immune system functions and they maybe help palliative care of patients in these conditions. Case Report: A patient with rectal adenocarcinoma with metastases decides to interrupt the clinical chemotherapy protocol due to refractoriness and side effects. As a palliative care alternative treatment it is suggested to the patient the use of ozone therapy associated with PEMF techniques. Results: The patient reports an improvement in well-being, in autonomy and in pain control. Imaging tests confirm a pause in tumor growth despite more than 60 days without using classic treatment. These results associated with palliative care alternative treatment stimulate the return to the chemotherapy protocol. Discussion: This case illustrates that these two techniques can contribute to the control of tumor growth and refractory symptoms, such as pain, probably by enhancing the immune system. Conclusions: The potential use of the combination of these two therapies, ozone therapy and PEMF therapy, can contribute to palliation of cancer patients, alone or in combination with pharmacological therapies. The conduct of future investigations on this paradigm can elucidate how much these techniques contribute to the survival and well-being of these patients.
Abstract: Assembly of the proton exchange membrane fuel cells (PEMFC) has a very important influence on its performance and efficiency. The various components of PEMFC stack are usually locked and fixed by bolts. Locking bolt will cause the deformation of the bipolar plate and the other components, which will affect directly the deformation degree of the integral parts of the PEMFC as well as the performance of PEMFC. This paper focuses on the object of three-cell stack of PEMFC. Finite element simulation is used to investigate the deformation of bipolar plate caused by quantity and layout of bolts, bolt locking pressure, and bolt locking sequence, etc. Finally, we made a conclusion that the optimal combination packaging scheme was adopted to assemble the fuel cell stack. The scheme was in use of 3.8 MPa locking pressure imposed on the fuel cell stack, type Ⅱ of four locking bolts and longitudinal locking method. The scheme was obtained by comparatively analyzing the overall displacement contour of PEMFC stack, absolute displacement curve of bipolar plate along the given three paths in the Z direction and the polarization curve of fuel cell. The research results are helpful for the fuel cell stack assembly.
Abstract: Bhutan is becoming increasingly dependent on Information and Communications Technologies (ICTs), especially the Internet for performing the daily activities of governments, businesses, and individuals. Consequently, information systems and networks are becoming more exposed and vulnerable to cybersecurity threats. This paper highlights the findings of the survey study carried out to understand the perceptions of cybersecurity implementation among government organizations in Bhutan. About 280 ICT personnel were surveyed about the effectiveness of cybersecurity implementation in their organizations. A questionnaire based on a 5 point Likert scale was used to assess the perceptions of respondents. The questions were asked on cybersecurity practices such as cybersecurity policies, awareness and training, and risk management. The survey results show that less than 50% of respondents believe that the cybersecurity implementation is effective: cybersecurity policy (40%), risk management (23%), training and awareness (28%), system development life cycle (34%); incident management (26%), and communications and operational management (40%). The findings suggest that many of the cybersecurity practices are inadequately implemented and therefore, there exist a gap in achieving a required cybersecurity posture. This study recommends government organizations to establish a comprehensive cybersecurity program with emphasis on cybersecurity policy, risk management, and awareness and training. In addition, the research study has practical implications to both government and private organizations for implementing and managing cybersecurity.
Abstract: In recent years, increasing usage of electrical energy provides a widespread field for investigating new methods to produce clean electricity with high reliability and cost management. Fuel cells are new clean generations to make electricity and thermal energy together with high performance and no environmental pollution. According to the expansion of fuel cell usage in different industrial networks, the identification and optimization of its parameters is really significant. This paper presents optimization of a proton exchange membrane fuel cell (PEMFC) parameters based on modified particle swarm optimization with real valued mutation (RVM) and clonal algorithms. Mathematical equations of this type of fuel cell are presented as the main model structure in the optimization process. Optimized parameters based on clonal and RVM algorithms are compared with the desired values in the presence and absence of measurement noise. This paper shows that these methods can improve the performance of traditional optimization methods. Simulation results are employed to analyze and compare the performance of these methodologies in order to optimize the proton exchange membrane fuel cell parameters.
Abstract: Reinforced concrete bridges designed by code are intended to achieve target reliability levels adequate for the geographical environment where the code is applicable. Several methods can be used to estimate such reliability levels. Many of them require the establishment of an explicit limit state function (LSF). When such LSF is not available as a close-form expression, the simulation techniques are often employed. The simulation methods are computing intensive and time consuming. Note that if the reliability of real bridges designed by code is of interest, numerical schemes, the finite element method (FEM) or computational mechanics could be required. In these cases, it can be quite difficult (or impossible) to establish a close-form of the LSF, and the simulation techniques may be necessary to compute reliability levels. To overcome the need for a large number of simulations when no explicit LSF is available, the point estimate method (PEM) could be considered as an alternative. It has the advantage that only the probabilistic moments of the random variables are required. However, in the PEM, fitting of the resulting moments of the LSF to a probability density function (PDF) is needed. In the present study, a very simple alternative which allows the assessment of the reliability levels when no explicit LSF is available and without the need of extensive simulations is employed. The alternative includes the use of the PEM, and its applicability is shown by assessing reliability levels of reinforced concrete bridges in Mexico when a numerical scheme is required. Comparisons with results by using the Monte Carlo simulation (MCS) technique are included. To overcome the problem of approximating the probabilistic moments from the PEM to a PDF, a well-known distribution is employed. The approach mixes the PEM and other classic reliability method (first order reliability method, FORM). The results in the present study are in good agreement whit those computed with the MCS. Therefore, the alternative of mixing the reliability methods is a very valuable option to determine reliability levels when no close form of the LSF is available, or if numerical schemes, the FEM or computational mechanics are employed.
Abstract: We present in this work our model of road traffic
emissions (line sources) and dispersion of these emissions, named
DISPOLSPEM (Dispersion of Poly Sources and Pollutants Emission
Model). In its emission part, this model was designed to keep the
consistent bottom-up and top-down approaches. It also allows to
generate emission inventories from reduced input parameters being
adapted to existing conditions in Morocco and in the other developing
countries. While several simplifications are made, all the performance
of the model results are kept. A further important advantage of
the model is that it allows the uncertainty calculation and emission
rate uncertainty according to each of the input parameters. In the
dispersion part of the model, an improved line source model has
been developed, implemented and tested against a reference solution.
It provides improvement in accuracy over previous formulas of line
source Gaussian plume model, without being too demanding in terms
of computational resources. In the case study presented here, the
biggest errors were associated with the ends of line source sections;
these errors will be canceled by adjacent sections of line sources
during the simulation of a road network. In cases where the wind
is parallel to the source line, the use of the combination discretized
source and analytical line source formulas minimizes remarkably the
error. Because this combination is applied only for a small number
of wind directions, it should not excessively increase the calculation
time.
Abstract: Nanofibers are defined as fibers with diameters less
than 100 nanometers. In this study, behaviours of activated carbon
nanofiber (ACNF), carbon nanofiber (CNF), polyacrylonitrile/ carbon
nanotube (PAN/CNT), polyvinyl alcohol/nanosilver (PVA/Ag) in
proton exchange membrane (PEM) fuel cells are investigated
experimentally. This material was used as gas diffusion layer (GDL)
in PEM fuel cells. In this study, the electrical conductivities of
nanofiber and nanofiber/nanoparticles have been studied to
understand their effects on PEM fuel cell performance. According to
the experimental results, the maximum electrical conductivity
performance of the fuel cell with nanofiber was found to be at
PVA/Ag (at UConn condition). The electrical conductivities of CNF,
ACNF, PAN/CNT are lower for PEM. The resistance of cell with
PVA/Ag is lower than the resistance of cell with PAN/CNT, ACNF,
CNF.
Abstract: In this paper, a prototype PEM fuel cell vehicle
integrated with a 1 kW air-blowing proton exchange membrane fuel
cell (PEMFC) stack as a main power sources has been developed for
a lightweight cruising vehicle. The test vehicle is equipped with a
PEM fuel cell system that provides electric power to a brushed DC
motor. This vehicle was designed to compete with industrial
lightweight vehicle with the target of consuming least amount of
energy and high performance. Individual variations in driving style
have a significant impact on vehicle energy efficiency and it is well
established from the literature. The primary aim of this study was to
assesses the power and fuel consumption of a hydrogen fuel cell
vehicle operating at three difference driving technique (i.e. 25 km/h
constant speed, 22-28 km/h speed range, 20-30 km/h speed range).
The goal is to develop the best driving strategy to maximize
performance and minimize fuel consumption for the vehicle system.
The relationship between power demand and hydrogen consumption
has also been discussed. All the techniques can be evaluated and
compared on broadly similar terms. Automatic intelligent controller
for driving prototype fuel cell vehicle on different obstacle while
maintaining all systems at maximum efficiency was used. The result
showed that 25 km/h constant speed was identified for optimal
driving with less fuel consumption.
Abstract: Hydrogen produced by means of polymer electrolyte
membrane electrolyzer (PEME) is one of the most promising
methods due to clean and renewable energy source. In the process,
some energy loss due to mass transfer through a PEM is caused by
diffusion, electro-osmotic drag, and the pressure difference between
the cathode channel and anode channel. In PEME, water molecules
and ionic particles transferred between the electrodes from anode to
cathode, Extensive mixing of the hydrogen and oxygen at anode
channel due to gases cross-over must be avoided. In recent times the
consciousness of safety issue in high pressure PEME where the
oxygen mix with hydrogen at anode channel could create, explosive
conditions have generated a lot of concern. In this paper, the steady
state and simulation analysis of gases crossover in PEME on the
temperature and pressure effect are presented. The simulations have
been analysis in MATLAB based on the well-known Fick’s Law of
molecular diffusion. The simulation results indicated that as
temperature increases, there is a significant decrease in operating
voltage.
Abstract: The paper discusses the problem of load transport
using farm tractors and road tractor units. This type of carriage of
goods is often done with farm vehicles. The tests were performed
with the PEMS equipment (Portable Emission Measurement System)
under actual traffic conditions. The vehicles carried a load of 20000
kg. This research method is one of the most desired because it
provides reliable information on the actual vehicle emissions and fuel
consumption (carbon balance method). For the tests, a route was
selected that simulated a trip from a small town to a food-processing
facility located in a city. The analysis of the obtained results gave a
clear answer as to what vehicles need to be used for carriage of this
type of cargo in terms of exhaust emissions and fuel consumption.
Abstract: This paper discusses the thematic structure of Yoruba
popular music of Southwest Nigeria. It examines the use of themes
and variations in early and contemporary Juju music. The work is an
outcome of a research developed by the author in his doctoral studies
at the University of Lagos, Nigeria, with the aim of analyzing the
thematic and motivic developments in Yoruba popular genres.
Observations, interviews, live recordings and CDs were used as
methods for eliciting information. Field recordings and CDs of
selected musical samples were also transcribed and notated. The
research established the prevalent use of string of themes by Juju
musicians as a compositional technique in moving from one musical
section to another, as they communicate the verbal messages in their
song. These themes consist of the popular ‘call and response’ form
found in most African music, analogous to the western ‘subject and
answer’ style of the fugue or sonata form, although without the tonic–
dominant relations. Due to the short and repetitive form of African
melodies and rhythms, a theme is restated as a variation, where its
rhythmic and melodic motifs are stylistically developed and repeated,
but still retaining its recognizable core musical structure. The
findings of this study showed that Juju musicians generally often
employ a thematic plan where new themes are used to arrange the
songs into sections, and each theme is developed into variations in
order to further expand the music, eliminate monotony, and create
musical aesthetics, serving as hallmark of its musical identity. The
study established the musical and extra-musical attributes of the
genre, while recommending further research towards analyzing the
various compositional techniques employed in African popular
genres.
Abstract: Thermal enhancement of a single mini channel in
Proton Exchange Membrane Fuel Cell (PEMFC) cooling plate is
numerically investigated. In this study, low concentration of Al2O3 in
Water - Ethylene Glycol mixtures is used as coolant in single channel
of carbon graphite plate to mimic the mini channels in PEMFC
cooling plate. A steady and incompressible flow with constant heat
flux is assumed in the channel of 1mm x 5mm x 100mm. Nano
particle of Al2O3 used ranges from 0.1, 0.3 and 0.5 vol %
concentration and then dispersed in 60:40 (water: Ethylene Glycol)
mixture. The effect of different flow rates to fluid flow and heat
transfer enhancement in Re number range of 20 to 140 was observed.
The result showed that heat transfer coefficient was improved by
18.11%, 9.86% and 5.37% for 0.5, 0.3 and 0.1 vol. % Al2O3 in 60:40
(water: EG) as compared to base fluid of 60:40 (water: EG). It is also
showed that the higher vol. % concentration of Al2O3 performed
better in term of thermal enhancement but at the expense of higher
pumping power required due to increase in pressure drop
experienced. Maximum additional pumping power of 0.0012W was
required for 0.5 vol % Al2O3 in 60:40 (water: EG) at Re number 140.
Abstract: A comparison of activity and stability of the as-formed
Pt/C, Pt-Co and Pt-Pd/C electrocatalysts, prepared by a combined
approach of impregnation and seeding, was performed. According to
the activity test in a single Proton Exchange Membrane (PEM) fuel
cell, the Oxygen Reduction Reaction (ORR) activity of the Pt-M/C
electrocatalyst was slightly lower than that of Pt/C. The j0.9 V and
E10 mA/cm2 of the as-prepared electrocatalysts increased in the order of
Pt/C > Pt-Co/C > Pt-Pd/C. However, in the medium-to-high current
density region, Pt-Pd/C exhibited the best performance. With regard to
their stability in a 0.5 M H2SO4 electrolyte solution, the
electrochemical surface area decreased as the number of rounds of
repetitive potential cycling increased due to the dissolution of the
metals within the catalyst structure. For long-term measurement, Pt-
Pd/C was the most stable than the other three electrocatalysts.
Abstract: Durability of Membrane Electrode Assembly for
Proton Exchange Membrane Fuel Cells was evaluated in both steady
state and accelerated decay modes. Steady state mode was carried out
at constant current of 800mA/cm2 for 2500 hours using air as cathode
feed and pure hydrogen as anode feed. The degradation of the cell
voltage was 0.015V after such 2500 hrs operation. The degradation
rate was therefore calculated to be 6uV/hr. Continuously Vigorous
fluctuation of the cell voltage, which was switched between OCV and
0.2V, was employed for the accelerated decay mode. No obvious
change in performance of the MEA was observed after 10000 cycles
of such operation.
Abstract: Polymer Electrolyte Membrane Fuel Cell (PEMFC) is
such a time-vary nonlinear dynamic system. The traditional linear
modeling approach is hard to estimate structure correctly of PEMFC
system. From this reason, this paper presents a nonlinear modeling of
the PEMFC using Neural Network Auto-regressive model with
eXogenous inputs (NNARX) approach. The multilayer perception
(MLP) network is applied to evaluate the structure of the NNARX
model of PEMFC. The validity and accuracy of NNARX model are
tested by one step ahead relating output voltage to input current from
measured experimental of PEMFC. The results show that the obtained
nonlinear NNARX model can efficiently approximate the dynamic
mode of the PEMFC and model output and system measured output
consistently.
Abstract: This paper discusses the design and analysis of a
hybrid PV-Fuel cell energy system destined to power a DC load. The
system is composed of a photovoltaic array, a fuel cell, an
electrolyzer and a hydrogen tank. HOMER software is used in this
study to calculate the optimum capacities of the power system
components that their combination allows an efficient use of solar
resource to cover the hourly load needs. The optimal system sizing
allows establishing the right balance between the daily electrical
energy produced by the power system and the daily electrical energy
consumed by the DC load using a 28 KW PV array, a 7.5 KW fuel
cell, a 40KW electrolyzer and a 270 Kg hydrogen tank. The variation
of powers involved into the DC bus of the hybrid PV-fuel cell system
has been computed and analyzed for each hour over one year: the
output powers of the PV array and the fuel cell, the input power of
the elctrolyzer system and the DC primary load. Equally, the annual
variation of stored hydrogen produced by the electrolyzer has been
assessed. The PV array contributes in the power system with 82%
whereas the fuel cell produces 18%. 38% of the total energy
consumption belongs to the DC primary load while the rest goes to
the electrolyzer.
Abstract: In this paper, design of solid-state battery/supercapacitor emulator based on dc-dc boost converter is described.
The emulator mimics charging behavior of any storage device based
on a predefined behavior set by the user. The device is operated by a
two-level control structure: high-level emulating controller and low-
level input voltage controller. Simulation and experimental results are
shown to demonstrate the emulator operation.