Abstract: The study aimed to investigate characteristics of
vegetative tissue for taxonomic purpose and possibly trend of waste
application in industry. Stems and branches of 15 species in Solanum
found in Thailand were prepared for fiber and examined by light
microscopy. Microstructural characteristic data of fiber i.e. fiber
length and width, fiber lumen diameter and fiber cell wall thickness
were recorded. The longest average fiber cell length (>3.9 mm.) were
obtained in S. lycopersicum L. and S. tuberosum L. Fiber cells from
S. lycopersicum also revealed the widest average diameter of whole
cell and its lumen at >45.5 μm and >29 μm respectively. However
fiber cells with thickest wall of > 9.6 μm were belonged to the
ornamental tree species, S. wrightii Benth. The results showed that
the slenderness ratio, Runkel ratio, and flexibility coefficient, with
potentially suitable for feedstock in paper industry fell in 4 exotic
species, i.e. Solanumamericanum L., S. lycopersicum, S.
seaforthianum Andr., and S. tuberosum L
Abstract: Functional near infrared spectroscopy (fNIRS) is a
practical non-invasive optical technique to detect characteristic of
hemoglobin density dynamics response during functional activation of
the cerebral cortex. In this paper, fNIRS measurements were made in
the area of motor cortex from C4 position according to international
10-20 system. Three subjects, aged 23 - 30 years, were participated in
the experiment.
The aim of this paper was to evaluate the effects of different motor
activation tasks of the hemoglobin density dynamics of fNIRS signal.
The chaotic concept based on deterministic dynamics is an important
feature in biological signal analysis. This paper employs the chaotic
properties which is a novel method of nonlinear analysis, to analyze
and to quantify the chaotic property in the time series of the
hemoglobin dynamics of the various motor imagery tasks of fNIRS
signal. Usually, hemoglobin density in the human brain cortex is
found to change slowly in time. An inevitable noise caused by various
factors is to be included in a signal. So, principle component analysis
method (PCA) is utilized to remove high frequency component. The
phase pace is reconstructed and evaluated the Lyapunov spectrum, and
Lyapunov dimensions. From the experimental results, it can be
conclude that the signals measured by fNIRS are chaotic.
Abstract: In order to enhance the contrast in the regions where the pixels have similar intensities, this paper presents a new histogram equalization scheme. Conventional global equalization schemes over-equalizes these regions so that too bright or dark pixels are resulted and local equalization schemes produce unexpected discontinuities at the boundaries of the blocks. The proposed algorithm segments the original histogram into sub-histograms with reference to brightness level and equalizes each sub-histogram with the limited extents of equalization considering its mean and variance. The final image is determined as the weighted sum of the equalized images obtained by using the sub-histogram equalizations. By limiting the maximum and minimum ranges of equalization operations on individual sub-histograms, the over-equalization effect is eliminated. Also the result image does not miss feature information in low density histogram region since the remaining these area is applied separating equalization. This paper includes how to determine the segmentation points in the histogram. The proposed algorithm has been tested with more than 100 images having various contrasts in the images and the results are compared to the conventional approaches to show its superiority.
Abstract: In this note first we define the notions of intuitionistic
fuzzy dual positive implicative hyper K-ideals of types
1,2,3,4 and intuitionistic fuzzy dual hyper K-ideals. Then we
give some classifications about these notions according to the
level subsets. Also by given some examples we show that these
notions are not equivalent, however we prove some theorems
which show that there are some relationships between these
notions. Finally we define the notions of product and antiproduct
of two fuzzy subsets and then give some theorems
about the relationships between the intuitionistic fuzzy dual
positive implicative hyper K-ideal of types 1,2,3,4 and their
(anti-)products, in particular we give a main decomposition
theorem.
Abstract: Power transformers are among the most important and
expensive equipments in the electric power systems. Consequently
the transformer protection is an essential part of the system
protection. This paper presents a new method for locating
transformer winding faults such as turn-to-turn, turn-to-core, turn-totransformer
body, turn-to-earth, and high voltage winding to low
voltage winding. In this study the current and voltage signals of input
and output terminals of the transformer are measured, which the
Fourier transform of measured signals and harmonic analysis
determine the fault's location.
Abstract: In the current context of globalization, accountability has become a key subject of real interest for both, national and international business areas, due to the need for comparability and transparency of the economic situation, so we can speak about the harmonization and convergence of international accounting. The paper presents a qualitative research through content analysis of several reports concerning the roadmap for convergence. First, we develop a conceptual framework for the evolution of standards’ convergence and further we discuss the degree of standards harmonization and convergence between US GAAP and IAS/IFRS as to October 2012. We find that most topics did not follow the expected progress. Furthermore there are still some differences in the long-term project that are in process to be completed and other that were reassessed as a lower priority project.
Abstract: This research aims to study consumer acceptance of Tempeh from various raw materials (type of bean) and determine protein contents for comparison. Tempeh made from soybean, peanut, white kidney bean and sesame in the ratio: - soybean:sesame =1:0.1, soybean:white kidney:sesame =1:1:0.1, soybean:peanut:sesame =1:1:0.1 and peanut:white kidney bean: sesame =1:1:0.1. The study found that consumer is most satisfied with appearances on soybean mixed with white kidney and black sesame tempeh (3.98). The most satisfied tempeh with textures is soybean mixed with peanut and black sesame tempeh (4.00). The most satisfied tempeh with odor is peanut mixed with white kidney bean and black sesame tempeh (4.04). And the most satisfied tempeh with flavor is peanut mixed with white kidney bean and black sesame tempeh (4.2). The amount of protein in production, soybean tempeh has the highest protein. When we add sesame seeds, it made the protein content slightly decreased (1.86 and 0.6 %). When we use peanut as raw material, the protein content decreased 15.3%. And when we use
white kidney bean as raw material, the protein content decreased (22.77- 26.11%).
Abstract: Automatic reusability appraisal is helpful in
evaluating the quality of developed or developing reusable software
components and in identification of reusable components from
existing legacy systems; that can save cost of developing the
software from scratch. But the issue of how to identify reusable
components from existing systems has remained relatively
unexplored. In this research work, structural attributes of software
components are explored using software metrics and quality of the
software is inferred by different Neural Network based approaches,
taking the metric values as input. The calculated reusability value
enables to identify a good quality code automatically. It is found that
the reusability value determined is close to the manual analysis used
to be performed by the programmers or repository managers. So, the
developed system can be used to enhance the productivity and
quality of software development.
Abstract: .Hardware realization of a Neural Network (NN), to a large extent depends on the efficient implementation of a single neuron. FPGA-based reconfigurable computing architectures are suitable for hardware implementation of neural networks. FPGA realization of ANNs with a large number of neurons is still a challenging task. This paper discusses the issues involved in implementation of a multi-input neuron with linear/nonlinear excitation functions using FPGA. Implementation method with resource/speed tradeoff is proposed to handle signed decimal numbers. The VHDL coding developed is tested using Xilinx XC V50hq240 Chip. To improve the speed of operation a lookup table method is used. The problems involved in using a lookup table (LUT) for a nonlinear function is discussed. The percentage saving in resource and the improvement in speed with an LUT for a neuron is reported. An attempt is also made to derive a generalized formula for a multi-input neuron that facilitates to estimate approximately the total resource requirement and speed achievable for a given multilayer neural network. This facilitates the designer to choose the FPGA capacity for a given application. Using the proposed method of implementation a neural network based application, namely, a Space vector modulator for a vector-controlled drive is presented
Abstract: Obstructive sleep apnea in patients, between 70 and 80
percent, can be cured with just a posture correcting. The most import
thing to do this is detection of obstructive sleep apnea. Detection of
obstructive sleep apnea can be performed through heart rate variability
analysis using power spectrum density analysis. After HRV analysis
we needed to know the current position information for correcting the
position. The pressure sensors of the array type were used to obtain
position information. These sensors can obtain information from the
experimenter about position. In addition, air cylinder corrected the
position of the experimenter by lifting the bed. The experimenter can
be changed position without breaking during sleep by the system.
Polysomnograph recording were obtained from 10 patients. The
results of HRV analysis were that NLF and LF/HF ratio increased,
while NHF decreased during OSA. Position change had to be done the
periods.
Abstract: This paper presents the 20-GHz fractional PLL (Phase
Locked Loop) circuit for the next generation Wi-Fi by using 90 nm
TSMC process. The newly suggested millimeter wave 16/17
pre-scalar is designed and verified by measurement to make the
fractional PLL having a low quantization noise. The operational
bandwidth of the 60 GHz system is 15 % of the carrier frequency
which requires large value of Kv (VCO control gain) resulting in
degradation of phase noise. To solve this problem, this paper adopts
AFC (Automatic Frequency Controller) controlled 4-bit millimeter
wave VCO with small value of Kv. Also constant Kv is implemented
using 4-bit varactor bank. The measured operational bandwidth is 18.2
~ 23.2 GHz which is 25 % of the carrier frequency. The phase noise of
-58 and -96.2 dBc/Hz at 100 KHz and 1 MHz offset is measured
respectively. The total power consumption of the PLL is only 30 mW.
Abstract: This paper reported an experimental research of
steady-state heat transfer behaviour of a gas flowing through a fixed
bed under the different operating conditions. Studies had been carried
out in a fixed-bed packed methanol synthesis catalyst percolated by air
at appropriate flow rate. Both radial and axial direction temperature
distribution had been investigated under the different operating
conditions. The effects of operating conditions including the reactor
inlet air temperature, the heating pipe temperature and the air flow rate
on temperature distribution was investigated and the experimental
results showed that a higher inlet air temperature was conducive to
uniform temperature distribution in the fixed bed. A large temperature
drop existed at the radial direction, and the temperature drop increased
with the heating pipe temperature increasing under the experimental
conditions; the temperature profile of the vicinity of the heating pipe
was strongly affected by the heating pipe temperature. A higher air
flow rate can improve the heat transfer in the fixed bed. Based on the
thermal distribution, heat transfer models of the fixed bed could be
established, and the characteristics of the temperature distribution in
the fixed bed could be finely described, that had an important practical
significance.
Abstract: Wireless mesh networks based on IEEE 802.11
technology are a scalable and efficient solution for next generation
wireless networking to provide wide-area wideband internet access to
a significant number of users. The deployment of these wireless mesh
networks may be within different authorities and without any
planning, they are potentially overlapped partially or completely in
the same service area. The aim of the proposed model is design a new
model to Enhancement Throughput of Unplanned Wireless Mesh
Networks Deployment Using Partitioning Hierarchical Cluster
(PHC), the unplanned deployment of WMNs are determinates there
performance. We use throughput optimization approach to model the
unplanned WMNs deployment problem based on partitioning
hierarchical cluster (PHC) based architecture, in this paper the
researcher used bridge node by allowing interworking traffic between
these WMNs as solution for performance degradation.
Abstract: This paper presents an analysis result of relationship
between business and information technology (IT) in business process
reengineering (BPR). 258 Japanese firm-level data collected have been
analyzed using structural equation modeling. This analysis was aimed
to illuminating success factors of achieve effective BPR. Analysis was
focused on management factors (including organizational factors) and
implementing management method (e.g. balanced score card, internal
control, etc.).These results would contribute for achieving effective
BPR by showing effective tasks and environment to be focused.
Abstract: In this paper, a uniform calculus-based approach for
synthesizing monitors checking correctness properties specified by a
large variety of logics at runtime is provided, including future and past
time logics, interval logics, state machine and parameterized temporal
logics. We present a calculus mechanism to synthesize monitors from
the logical specification for the incremental analysis of execution
traces during test and real run. The monitor detects both good and bad
prefix of a particular kind, namely those that are informative for the
property under investigation. We elaborate the procedure of calculus
as monitors.
Abstract: Materials used on exterior spacecraft surfaces are subjected to many environmental threats which can cause degradation, atomic oxygen is one of the most threats. We prepared organic silicon atomic-oxygen-protection film using method of polymerization. This paper presented the effects on the film structure and its durability of the preparation processing, and analyzed the polymerization theory, the film structure and composition of the film. At last, we tested the film in our ground based atomic oxygen simulator, and indicated that the film worked well.
Abstract: Some Chromium (III) complexes were synthesized
with three amino acids: L Glutamic Acid, Glycine, and L-cysteine as
the ligands, in order to provide a new supplement containing Cr(III)
for patients with type 2 diabetes mellitus. The complexes have been
prepared by refluxing a mixture of Chromium(III) chloride in
aqueous solution with L-glutamic acid, Glycine, and L-cysteine after
pH adjustment by sodium hydroxide. These complexes were
characterized by Infrared and Uv-Vis spectrophotometer and
Elemental analyzer. The product yields of four products were 87.50
and 56.76% for Cr-Glu complexes, 46.70% for Cr-Gly complex and
40.08% for Cr-Cys complex respectively. The predicted structure of
the complexes are [Cr(glu)2(H2O)2].xH2O, Cr(gly)3..xH2O and
Cr(cys)3.xH2O., respectively.
Abstract: With the exponential rise in the number of multimedia
applications available, the best-effort service provided by the Internet
today is insufficient. Researchers have been working on new
architectures like the Next Generation Network (NGN) which, by
definition, will ensure Quality of Service (QoS) in an all-IP based
network [1]. For this approach to become a reality, reservation of
bandwidth is required per application per user. WiMAX (Worldwide
Interoperability for Microwave Access) is a wireless communication
technology which has predefined levels of QoS which can be
provided to the user [4]. IPv6 has been created as the successor for
IPv4 and resolves issues like the availability of IP addresses and
QoS. This paper provides a design to use the power of WiMAX as an
NSP (Network Service Provider) for NGN using IPv6. The use of the
Traffic Class (TC) field and the Flow Label (FL) field of IPv6 has
been explained for making QoS requests and grants [6], [7]. Using
these fields, the processing time is reduced and routing is simplified.
Also, we define the functioning of the ASN gateway and the NGN
gateway (NGNG) which are edge node interfaces in the NGNWiMAX
design. These gateways ensure QoS management through
built in functions and by certain physical resources and networking
capabilities.
Abstract: Recently, web services to access from many type devices
are often used. We have developed the shortest path planning
system called "Bus-Net" in Tottori prefecture as a web application
to sustain the public transport. And it used the same user interface
for both devices. To support both devices, the interface cannot use
JavaScript and so on.
Thus, we developed the method that use individual user interface
for each device type to improve its convenience. To be concrete,
we defined formats of condition input to the path planning system
and result output from it and separate the system into the request
processing part and user interface parts that depend on device types.
By this method, we have also developed special device for Bus-Net
named "Intelligent-Bus-Stop".
Abstract: Image compression can improve the performance of
the digital systems by reducing time and cost in image storage
and transmission without significant reduction of the image quality.
Furthermore, the discrete cosine transform has emerged as the new
state-of-the art standard for image compression. In this paper, a
hybrid image compression technique based on reversible blockade
transform coding is proposed. The technique, implemented over
regions of interest (ROIs), is based on selection of the coefficients
that belong to different transforms, depending on the coefficients is
proposed. This method allows: (1) codification of multiple kernals
at various degrees of interest, (2) arbitrary shaped spectrum,and (3)
flexible adjustment of the compression quality of the image and the
background. No standard modification for JPEG2000 decoder was
required. The method was applied over different types of images.
Results show a better performance for the selected regions, when
image coding methods were employed for the whole set of images.
We believe that this method is an excellent tool for future image
compression research, mainly on images where image coding can
be of interest, such as the medical imaging modalities and several
multimedia applications. Finally VLSI implementation of proposed
method is shown. It is also shown that the kernal of Hartley and
Cosine transform gives the better performance than any other model.