Abstract: Turbulent heat transfer to fluid flow through channel with triangular ribs of different angles are presented in this paper. Ansys 14 ICEM and Ansys 14 Fluent are used for meshing process and solving Navier stokes equations respectively. In this investigation three angles of triangular ribs with the range of Reynolds number varied from 20000 to 60000 at constant surface temperature are considered. The results show that the Nusselt number increases with the increase of Reynolds number for all cases at constant surface temperature. According to the profile of local Nusselt number on ribs walled of channel, the peak is at the midpoint between the two ribs. The maximum value of average Nusselt number is obtained for triangular ribs of angel 60°and at Reynolds number of 60000 compared to the Nusselt number for the ribs of angel 90° and 45° and at same Reynolds number. The recirculation regions generated by the ribs corresponding to the velocity streamline show the largest recirculation region at triangular ribs of angle 60° which also provides the highest enhancement of heat transfer.
Abstract: In this paper, an artificial neural network simulator is
employed to carry out diagnosis and prognosis on electric motor as
rotating machinery based on predictive maintenance. Vibration data
of the primary failed motor including unbalance, misalignment and
bearing fault were collected for training the neural network. Neural
network training was performed for a variety of inputs and the motor
condition was used as the expert training information. The main
purpose of applying the neural network as an expert system was to
detect the type of failure and applying preventive maintenance. The
advantage of this study is for machinery Industries by providing
appropriate maintenance that has an essential activity to keep the
production process going at all processes in the machinery industry.
Proper maintenance is pivotal in order to prevent the possible failures
in operating system and increase the availability and effectiveness of
a system by analyzing vibration monitoring and developing expert
system.
Abstract: A code has been developed in Mathematica using
Direct Simulation Monte Carlo (DSMC) technique. The code was
tested for 2-D air flow around a circular cylinder. Same geometry
and flow properties were used in FLUENT 6.2 for comparison. The
results obtained from Mathematica simulation indicated significant
agreement with FLUENT calculations, hence providing insight into
particle nature of fluid flows.
Abstract: The thermal expansion behaviour of silicon carbide
(SCS-2) fibre reinforced 6061 aluminium matrix composite subjected
to the influenced thermal mechanical cycling (TMC) process were
investigated. The thermal stress has important effect on the
longitudinal thermal expansion coefficient of the composites. The
present paper used experimental data of the thermal expansion
behaviour of a SiC/Al composite for temperatures up to 370°C, in
which their data was used for carrying out modelling of theoretical
predictions.
Abstract: In this paper, Land Marks for Unique Addressing( LMUA) algorithm is develped to generate unique ID for each and every node which leads to the formation of overlapping/Non overlapping clusters based on unique ID. To overcome the draw back of the developed LMUA algorithm, the concept of clustering is introduced. Based on the clustering concept a Land Marks for Unique Addressing and Clustering(LMUAC) Algorithm is developed to construct strictly non-overlapping clusters and classify those nodes in to Cluster Heads, Member Nodes, Gate way nodes and generating the Hierarchical code for the cluster heads to operate in the level one hierarchy for wireless communication switching. The expansion of the existing network can be performed or not without modifying the cost of adding the clusterhead is shown. The developed algorithm shows one way of efficiently constructing the
Abstract: The antimicrobial, antiplasmid and cytotoxic activities of marine algae Halimeda opuntia and Sarconema filiforme were investigated. Antimicrobial bioassay against some human pathogenic bacteria and yeast were conducted using disc diffusion method. Halimeda extract exhibited antibacterial activity against six species of microrganisms, with significant inhibition against Staphylococcus aureus. While Sarconema extract was better potent as antifungal against Candida albicans. Comparative antibacterial studies showed that Halimeda extract showed equivalent or better activity as compared with commercial antibiotic when tested against Staphylococcus aureus. Further tests conducted using dilution method showed both extracts as having bacteriostatic mode of action against the tested microorganisms. Methanol extract of two species showed significant cytotoxicity (LC50
Abstract: A facile vapour deposition method of synthesis of vertically aligned ZnO nanowires on carbon seed layer was developed. The received samples were investigated on electronic microscope JSM-6490 LA JEOL and x-ray diffractometer X, pert MPD PRO. The photoluminescence spectra (PL) of obtained ZnO samples at a room temperature were studied using He-Cd laser (325 nm line) as excitation source.
Abstract: In this paper, the optimum weight and cost of a laminated composite plate is seeked, while it undergoes the heaviest load prior to a complete failure. Various failure criteria are defined for such structures in the literature. In this work, the Tsai-Hill theory is used as the failure criterion. The theory of analysis was based on the Classical Lamination Theory (CLT). A newly type of Genetic Algorithm (GA) as an optimization technique with a direct use of real variables was employed. Yet, since the optimization via GAs is a long process, and the major time is consumed through the analysis, Radial Basis Function Neural Networks (RBFNN) was employed in predicting the output from the analysis. Thus, the process of optimization will be carried out through a hybrid neuro-GA environment, and the procedure will be carried out until a predicted optimum solution is achieved.
Abstract: In this paper, a residue number arithmetic is used in
direct sequence spread spectrum system, this system is evaluated and
the bit error probability of this system is compared to that of non
residue number system. The effect of channel bandwidth, PN
sequences, multipath effect and modulation scheme are studied. A
Matlab program is developed to measure the signal-to-noise ratio
(SNR), and the bit error probability for the various schemes.
Abstract: In this paper a numerical technique is used to predict
the metal temperature of a gas turbine vane. The Rising combustor
exit temperatures in gas turbine engines necessitate active cooling for
the downstream turbine section to avoid thermal failure. This study is
performed the solution of external flow, internal convection, and
conduction within the metal vane. Also the trade-off between the
cooling performances in four different hole shapes and configurations
is performed. At first one of the commonly used cooling hole
geometry is investigated; cylindrical holes and then two other
configurations are simulated. The average temperature magnitude in
mid-plan section of each configuration is obtained and finally the
lower temperature value is selected such as best arrangement.
Abstract: Developing techniques for mobile robot navigation constitutes one of the major trends in the current
research on mobile robotics. This paper develops a local
model network (LMN) for mobile robot navigation. The
LMN represents the mobile robot by a set of locally valid
submodels that are Multi-Layer Perceptrons (MLPs).
Training these submodels employs Back Propagation (BP) algorithm. The paper proposes the fuzzy C-means (FCM) in this scheme to divide the input space to sub regions, and then a submodel (MLP) is identified to represent a particular
region. The submodels then are combined in a unified
structure. In run time phase, Radial Basis Functions (RBFs) are employed as windows for the activated submodels. This
proposed structure overcomes the problem of changing operating regions of mobile robots. Read data are used in all experiments. Results for mobile robot navigation using the
proposed LMN reflect the soundness of the proposed
scheme.
Abstract: The evaluation of unit cell neutronic parameters and
lifetime for some innovant reactors without on sit-refuling will be
held in this work. the behavior of some small and medium reactors
without on site refueling with triso and cermet fuel. For the FBNR
long life except we propose to change the enrichment of the Cermet
MFE to 9%. For the AFPR reactor we can see that the use of the
Cermet MFE can extend the life of this reactor but to maintain the
same life period for AFPR-SC we most use burnup poison to have the
same slope for Kinf (Burnup). PFPWR50 cell behaves almost in
same way using both fuels Cermet and TRISO. So we can conclude
that PFPWR50 reactor, with CERMET Fuel, is kept among the long
cycle reactors and with the new configuration we avoid subcriticality
at the beginning of cycle. The evaluation of unit cell neutronic
parameters reveals a good agreement with the goal of BWR-PB
concept. It is found out that the Triso fuel assembly lifetime can be
extended for a reasonably long period without being refueled,
approximately up to 48GWd/t burnup. Using coated particles fuels
with the Cermet composition can be more extended the fuel assembly
life time, approximately 52 GWd/t.
Abstract: The application of stability theory has led to detailed studies of different types of vessels; however, the shortage of information relating to multihull vessels demanded further investigation. This study shows that the position of the hulls has a very influential effect on both the transverse and longitudinal stability of the tricore. HSC stability code is applied for the optimisation of the hull configurations. Such optimization criteria would undoubtedly aid the performance of the vessel for both commercial or leisure purposes
Abstract: ZnO nanocrystals with mean diameter size 14 nm
have been prepared by precipitation method, and examined as
photocatalyst for the UV-induced degradation of insecticide diazinon
as deputy of organic pollutant in aqueous solution. The effects of
various parameters, such as illumination time, the amount of
photocatalyst, initial pH values and initial concentration of
insecticide on the photocatalytic degradation diazinon were
investigated to find desired conditions. In this case, the desired
parameters were also tested for the treatment of real water containing
the insecticide. Photodegradation efficiency of diazinon was
compared between commercial and prepared ZnO nanocrystals. The
results indicated that UV/ZnO process applying prepared
nanocrystalline ZnO offered electrical energy efficiency and
quantum yield better than commercial ZnO. The present study, on the
base of Langmuir-Hinshelwood mechanism, illustrated a pseudo
first-order kinetic model with rate constant of surface reaction equal
to 0.209 mg l-1 min-1 and adsorption equilibrium constant of 0.124 l
mg-1.
Abstract: In this study, a Loop Back Algorithm for component
connected labeling for detecting objects in a digital image is
presented. The approach is using loop back connected component
labeling algorithm that helps the system to distinguish the object
detected according to their label. Deferent than whole window
scanning technique, this technique reduces the searching time for
locating the object by focusing on the suspected object based on
certain features defined. In this study, the approach was also
implemented for a face detection system. Face detection system is
becoming interesting research since there are many devices or
systems that require detecting the face for certain purposes. The input
can be from still image or videos, therefore the sub process of this
system has to be simple, efficient and accurate to give a good result.
Abstract: Computer aided design accounts with the support of
parametric software in the design of machine components as well as
of any other pieces of interest. The complexities of the element under
study sometimes offer certain difficulties to computer design, or ever
might generate mistakes in the final body conception. Reverse
engineering techniques are based on the transformation of already
conceived body images into a matrix of points which can be
visualized by the design software. The literature exhibits several
techniques to obtain machine components dimensional fields, as
contact instrument (MMC), calipers and optical methods as laser
scanner, holograms as well as moiré methods. The objective of this
research work was to analyze the moiré technique as instrument of
reverse engineering, applied to bodies of nom complex geometry as
simple solid figures, creating matrices of points. These matrices were
forwarded to a parametric software named SolidWorks to generate
the virtual object. Volume data obtained by mechanical means, i.e.,
by caliper, the volume obtained through the moiré method and the
volume generated by the SolidWorks software were compared and
found to be in close agreement. This research work suggests the
application of phase shifting moiré methods as instrument of reverse
engineering, serving also to support farm machinery element designs.
Abstract: The purpose of this study was to measure the maximal
isometric strength and to investigate the effects of different handleheights
and elbow angles with respect to Mid. sagittal plane on the
pushing and pulling strength in vertical direction. Eight male subjects
performed a series of static strength measurement for each subject.
The highest isometric strength was found in pulling at shoulder
height (S.H.) (Mean = 60.29 lb., SD = 16.78 lb.) and the lowest
isometric strength was found also in pulling at elbow height (E.H.)
(Mean = 33.06 lb., SD = 6.56 lb.). Although the isometric strengths
were higher at S.H than at E.H. for both activities, the maximal
isometric strengths were compared statistically. ANOVA was
performed. The results of the experiment revealed that there was a
significant different between handle heights. However, there were no
significant different between angles and activities, also no correlation
between grip strength and activities.
Abstract: Based on the component approach, three kinds of
dynamic load models, including a single –motor model, a two-motor
model and composite load model have been developed for the
stability studies of Khuzestan power system. The study results are
presented in this paper. Voltage instability is a dynamic phenomenon
and therefore requires dynamic representation of the power system
components. Industrial loads contain a large fraction of induction
machines. Several models of different complexity are available for
the description investigations. This study evaluates the dynamic
performances of several dynamic load models in combination with
the dynamics of a load changing transformer. Case study is steel
industrial substation in Khuzestan power systems.
Abstract: Although considerable amount of research has attested to the link between work-to-family conflict (WFC) and family-to-work conflict (FWC) and psychological strain and wellbeing, there is a paucity of research investigating the phenomenon in the context of social workers. Moreover, very little is known about the impact of WFC and FWC in developing countries. The present study investigated the mediating effect of psychological strain on the relationship between WFC and FWC with wellbeing of social workers in India. Our findings show that WFC and FWC are influential antecedents of wellbeing; their influence is both direct on psychological strain, and indirect on wellbeing transmitted through psychological strain. Implications of the findings are discussed.
Abstract: Data mining uses a variety of techniques each of which
is useful for some particular task. It is important to have a deep
understanding of each technique and be able to perform sophisticated
analysis. In this article we describe a tool built to simulate a variation
of the Kohonen network to perform unsupervised clustering and
support the entire data mining process up to results visualization. A
graphical representation helps the user to find out a strategy to
optimize classification by adding, moving or delete a neuron in order
to change the number of classes. The tool is able to automatically
suggest a strategy to optimize the number of classes optimization, but
also support both tree classifications and semi-lattice organizations of
the classes to give to the users the possibility of passing from one
class to the ones with which it has some aspects in common.
Examples of using tree and semi-lattice classifications are given to
illustrate advantages and problems. The tool is applied to classify
macroeconomic data that report the most developed countries- import
and export. It is possible to classify the countries based on their
economic behaviour and use the tool to characterize the commercial
behaviour of a country in a selected class from the analysis of
positive and negative features that contribute to classes formation.
Possible interrelationships between the classes and their meaning are
also discussed.