Abstract: A direct search approach to determine optimal reservoir operating is proposed with ant colony optimization for continuous domains (ACOR). The model is applied to a system of single reservoir to determine the optimum releases during 42 years of monthly steps. A disadvantage of ant colony based methods and the ACOR in particular, refers to great amount of computer run time consumption. In this study a highly effective procedure for decreasing run time has been developed. The results are compared to those of a GA based model.
Abstract: The sensitivity of UAVs to the atmospheric effects are
apparent. All the same the meteorological support for the UAVs
missions is often non-adequate or partly missing.
In our paper we show a new complex meteorological support
system for different types of UAVs pilots, specialists and decision
makers, too. The mentioned system has two important parts with
different forecasts approach such as the statistical and dynamical
ones.
The statistical prediction approach is based on a large
climatological data base and the special analog method which is able
to select similar weather situations from the mentioned data base to
apply them during the forecasting procedure.
The applied dynamic approach uses the specific WRF model runs
twice a day and produces 96 hours, high resolution weather forecast
for the UAV users over the Hungary. An easy to use web-based
system can give important weather information over the Carpathian
basin in Central-Europe. The mentioned products can be reached via
internet connection.
Abstract: When designing satellites, one of the major issues aside for designing its primary subsystems is to devise its thermal. The thermal management of satellites requires solving different sets of issues with regards to modelling. If the satellite is well conditioned all other parts of the satellite will have higher temperature no matter what. The main issue of thermal modelling for satellite design is really making sure that all the other points of the satellite will be within the temperature limits they are designed. The insertion of power electronics in aerospace technologies is becoming widespread and the modern electronic systems used in space must be reliable and efficient with thermal management unaffected by outer space constraints. Many advanced thermal management techniques have been developed in recent years that have application in high power electronic systems. This paper presents a Three-Dimensional Modal Transmission Line Matrix (3D-TLM) implementation of transient heat flow in space power electronics. In such kind of components heat dissipation and good thermal management are essential. Simulation provides the cheapest tool to investigate all aspects of power handling. The 3DTLM has been successful in modeling heat diffusion problems and has proven to be efficient in terms of stability and complex geometry. The results show a three-dimensional visualisation of self-heating phenomena in the device affected by outer space constraints, and will presents possible approaches for increasing the heat dissipation capability of the power modules.
Abstract: The paper proposes a methodology to process the signals coming from the Transcranial Magnetic Stimulation (TMS) in order to identify the pathology and evaluate the therapy to treat the patients affected by demency diseases. In particular, a fuzzy model is developed to identify the demency of the patients affected by Subcortical Ischemic Vascular Dementia (SIVD) and to measure the effect of a repetitive TMS on their motor performances. A tool is also presented to support the mentioned analysis.
Abstract: In this paper, we analyze and test a scheme for the
estimation of electrical fundamental frequency signals from the
harmonic load current and voltage signals.
The scheme was based on using two different Multi Layer
Artificial Neural Networks (ML-ANN) one for the current and the
other for the voltage.
This study also analyzes and tests the effect of choosing the
optimum artificial neural networks- sizes which determine the quality
and accuracy of the estimation of electrical fundamental frequency
signals.
The simulink tool box of the Matlab program for the simulation of
the test system and the test of the neural networks has been used.
Abstract: Corrosion of metallic water pipelines buried below
ground surface is a function of the nature of the surrounding soil and
groundwater. This gives the importance of knowing the physical and
chemical characteristics of the pipe-s surrounding environment. The
corrosion of externally – unprotected metallic water pipelines,
specially ductile iron pipes, in localities with aggressive soil
conditions is becoming a significant problem. Anticorrosive
protection for metallic water pipelines, their fittings and accessories
is very important, because they may be attached by corrosion with
time. The tendency of a metallic substrate to corrode is a function of
the surface characteristics of the metal and of the metal/protective
film interface, the physical, electrical and electrochemical properties
of the film, and the nature of the environment in which the pipelines
system is placed. In this work the authors have looked at corrosion
problems of water pipelines and their control. The corrosive
properties of groundwater and soil environments are reviewed, and
parameters affecting corrosion are discussed. The purpose of this
work is to provide guidelines for materials selection in water and soil
environments, and how the water pipelines can be protected against
metallic corrosion.
Abstract: A pressure-based implicit procedure to solve Navier-
Stokes equations on a nonorthogonal mesh with collocated finite
volume formulation is used to simulate flow around the smart and
conventional flaps of spoiler under the ground effect. Cantilever
beam with uniformly varying load with roller support at the free end
is considered for smart flaps. The boundedness criteria for this
procedure are determined from a Normalized Variable diagram
(NVD) scheme. The procedure incorporates es the k -ε eddyviscosity
turbulence model. The method is first validated against
experimental data. Then, the algorithm is applied for turbulent
aerodynamic flows around a spoiler section with smart and
conventional flaps for different attack angle, flap angle and ground
clearance where the results of two flaps are compared.
Abstract: In this paper, we present a novel, principled approach to resolve the remained problems of substitution technique of audio steganography. Using the proposed genetic algorithm, message bits are embedded into multiple, vague and higher LSB layers, resulting in increased robustness. The robustness specially would be increased against those intentional attacks which try to reveal the hidden message and also some unintentional attacks like noise addition as well.
Abstract: This study investigates CO2 mitigation by methanol
synthesis from flue gas CO2 and H2 generation through water
electrolysis. Electrolytic hydrogen generation is viable provided that
the required electrical power is supplied from renewable energy
resources; whereby power generation from renewable resources is yet
commercial challenging. This approach contribute to zero-emission,
moreover it produce oxygen which could be used as feedstock for
chemical process. At ZPC, however, oxygen would be utilized
through partial oxidation of methane in autothermal reactor (ATR);
this makes ease the difficulties of O2 delivery and marketing. On the
other hand, onboard hydrogen storage and consumption; in methanol
plant; make the project economically more competitive.
Abstract: Evaporator is an important and widely used heat
exchanger in air conditioning and refrigeration industries. Different
methods have been used by investigators to increase the heat transfer
rates in evaporators. One of the passive techniques to enhance heat
transfer coefficient is the application of microfin tubes. The
mechanism of heat transfer augmentation in microfin tubes is
dependent on the flow regime of two-phase flow. Therefore many
investigations of the flow patterns for in-tube evaporation have been
reported in literatures. The gravitational force, surface tension and
the vapor-liquid interfacial shear stress are known as three dominant
factors controlling the vapor and liquid distribution inside the tube. A
review of the existing literature reveals that the previous
investigations were concerned with the two-phase flow pattern for
flow boiling in horizontal tubes [12], [9]. Therefore, the objective of
the present investigation is to obtain information about the two-phase
flow patterns for evaporation of R-134a inside horizontal smooth and
microfin tubes. Also Investigation of heat transfer during flow
boiling of R-134a inside horizontal microfin and smooth tube have
been carried out experimentally The heat transfer coefficients for
annular flow in the smooth tube is shown to agree well with Gungor
and Winterton-s correlation [4]. All the flow patterns occurred in the
test can be divided into three dominant regimes, i.e., stratified-wavy
flow, wavy-annular flow and annular flow. Experimental data are
plotted in two kinds of flow maps, i.e., Weber number for the vapor
versus weber number for the liquid flow map and mass flux versus
vapor quality flow map. The transition from wavy-annular flow to
annular or stratified-wavy flow is identified in the flow maps.
Abstract: Many works have been carried out to compare the
efficiency of several goodness of fit procedures for identifying
whether or not a particular distribution could adequately explain a
data set. In this paper a study is conducted to investigate the power
of several goodness of fit tests such as Kolmogorov Smirnov (KS),
Anderson-Darling(AD), Cramer- von- Mises (CV) and a proposed
modification of Kolmogorov-Smirnov goodness of fit test which
incorporates a variance stabilizing transformation (FKS). The
performances of these selected tests are studied under simple
random sampling (SRS) and Ranked Set Sampling (RSS). This
study shows that, in general, the Anderson-Darling (AD) test
performs better than other GOF tests. However, there are some
cases where the proposed test can perform as equally good as the
AD test.
Abstract: In this paper, Novel method, Particle Swarm Optimization (PSO) algorithm, based technique is proposed to estimate and analyze the steady state performance of self-excited induction generator (SEIG). In this novel method the tedious job of deriving the complex coefficients of a polynomial equation and solving it, as in previous methods, is not required. By comparing the simulation results obtained by the proposed method with those obtained by the well known mathematical methods, a good agreement between these results is obtained. The comparison validates the effectiveness of the proposed technique.
Abstract: The two significant overvoltages in power system,
switching overvoltage and lightning overvoltage, are investigated in
this paper. Firstly, the effect of various power system parameters on
Line Energization overvoltages is evaluated by simulation in ATP.
The dominant parameters include line parameters; short-circuit
impedance and circuit breaker parameters. Solutions to reduce
switching overvoltages are reviewed and controlled closing using
switchsync controllers is proposed as proper method.
This paper also investigates lightning overvoltages in the
overhead-cable transition. Simulations are performed in
PSCAD/EMTDC. Surge arresters are applied in both ends of cable to
fulfill the insulation coordination. The maximum amplitude of
overvoltages inside the cable is surveyed which should be of great
concerns in insulation coordination studies.
Abstract: A new analytical method to predict the torsional
capacity and behavior of R.C multi-cell box girders strengthened with
carbon fiber reinforced polymer (CFRP) sheets is presented.
Modification was done on the Softened Truss Model (STM) in the
proposed method; the concrete torsional problem is solved by
combining the equilibrium conditions, compatibility conditions and
constitutive laws of materials by taking into account the confinement
of concrete with CFRP sheets. A specific algorithm is developed to
predict the torsional behavior of reinforced concrete multi-cell box
girders with or without strengthening by CFRP sheets. Applications
of the developed method as an assessment tool to strengthened multicell
box girders with CFRP and first analytical example that
demonstrate the contribution of the CFRP materials on the torsional
response is also included.
Abstract: In studying the possibility of using plants as
rhizoremediators, barley and grass mixture which showed resistance
to various concentrations of oil were selected. The minimum
inhibitory effect of oil on these plants by morphological parameters
such as survival of plants, length and biomass of shoot and root
compared with the control was showed. In determining physiological
parameters, a slight decrease in the number of chlorophyll a and b in
the leaves of plants was noted. The differences in the ratio of the total
surface of the roots to the work surface with the growth of plants in
soil with oil in the study of adsorption of the root surface were
showed.
Abstract: Inconel718 has been widely used as a super alloy in aerospace application due to the high strength at elevated temperatures, satisfactory oxidation resistance and heat corrosion resistance. In this study, the Inconel718 has been fabricated using high technology of Metal Injection Molding (MIM) process due to the cost effective technique for producing small, complex and precision parts in high volume compared with conventional method through machining. Through MIM, the binder system is one of the most important criteria in order to successfully fabricate the Inconel718. Even though, the binder system is a temporary, but failure in the selection and removal of the binder system will affect on the final properties of the sintered parts. Therefore, the binder system based on palm oil derivative which is palm stearin has been formulated and developed to replace the conventional binder system. The rheological studies of the mixture between the powder and binders system have been determined properly in order to be successful during injection into injection molding machine. After molding, the binder holds the particles in place. The binder system has to be removed completely through debinding step. During debinding step, solvent debinding and thermal pyrolysis has been used to remove completely of the binder system. The debound part is then sintered to give the required physical and mechanical properties. The results show that the properties of the final sintered parts fulfill the Standard Metal Powder Industries Federation (MPIF) 35 for MIM parts.
Abstract: Security has been an important issue and concern in the
smart home systems. Smart home networks consist of a wide range of
wired or wireless devices, there is possibility that illegal access to
some restricted data or devices may happen. Password-based
authentication is widely used to identify authorize users, because this
method is cheap, easy and quite accurate. In this paper, a neural
network is trained to store the passwords instead of using verification
table. This method is useful in solving security problems that
happened in some authentication system. The conventional way to
train the network using Backpropagation (BPN) requires a long
training time. Hence, a faster training algorithm, Resilient
Backpropagation (RPROP) is embedded to the MLPs Neural
Network to accelerate the training process. For the Data Part, 200
sets of UserID and Passwords were created and encoded into binary
as the input. The simulation had been carried out to evaluate the
performance for different number of hidden neurons and combination
of transfer functions. Mean Square Error (MSE), training time and
number of epochs are used to determine the network performance.
From the results obtained, using Tansig and Purelin in hidden and
output layer and 250 hidden neurons gave the better performance. As
a result, a password-based user authentication system for smart home
by using neural network had been developed successfully.
Abstract: Growth and mineral nutrient elemental content were
studied in Mokara chark kuan pink terrestrial orchid and wild
Lantana camara weed agroecosystem. The treated subplots were
encircled with L. camara plants and sprayed weekly with L. camara
10% leaf aqueous extract. Allelopathic interactions were possible
through extensive invading root of L. camara plants into the treated
orchid subplots and weekly L. camara leaf aqueous extract
sprayings. Orchid growth was not significantly different in between
the control and treated plots, but chlorosis and yellowish patches of
leaves were observed in control orchid leaves. Nitrogen content in L.
camara leaf was significantly higher than in orchid leaf, the order of
importance of mineral nutrient contents in L. camara leaf was
K>Mg>Na>N. In treated orchid leaf, the order of importance was
N>K>Mg>Na. Orchid leaf N content from the treated plot was
higher than control, but Mg and Na contents were almost similar.
Abstract: The main aim of this study is to identify the most
influential variables that cause defects on the items produced by a
casting company located in Turkey. To this end, one of the items
produced by the company with high defective percentage rates is
selected. Two approaches-the regression analysis and decision treesare
used to model the relationship between process parameters and
defect types. Although logistic regression models failed, decision tree
model gives meaningful results. Based on these results, it can be
claimed that the decision tree approach is a promising technique for
determining the most important process variables.
Abstract: Many corporations are seriously concerned about
security of networks and therefore, their network supervisors are still
reluctant to install WLANs. In this regards, the IEEE802.11i standard
was developed to address the security problems, even though the
mistrust of the wireless LAN technology is still existing. The thought
was that the best security solutions could be found in open standards
based technologies that can be delivered by Virtual Private
Networking (VPN) being used for long time without addressing any
security holes for the past few years. This work, addresses this issue
and presents a simulated wireless LAN of IEEE802.11g protocol, and
analyzes impact of integrating Virtual Private Network technology to
secure the flow of traffic between the client and the server within the
LAN, using OPNET WLAN utility. Two Wireless LAN scenarios
have been introduced and simulated. These are based on normal
extension to a wired network and VPN over extension to a wired
network. The results of the two scenarios are compared and indicate
the impact of improving performance, measured by response time
and load, of Virtual Private Network over wireless LAN.