Abstract: Asthma is a condition that causing chronic health problems in children. In addition to basic therapy against disease, we must try to reduce the impact of chronic health problems and also optimize their medical aspect of growth and development. A boy with mild asthma attack frequent episode did not showed any improvement with medical treatment and his asthma control test was 11. From radiologic examination he got hyperaerated lung and billateral sinusitis maxillaris; skin test results were house dust, food and pet allergy; an overweight body; bad school grades; psychological and environmental problem. We followed and evaluated this boy in 6 months, treated holistically. Even we could not do much on environmental but no more psychological and school problems, his on a good bodyweight and his asthma control test was 22. A case of a child with mild asthma attack frequent episode was reported. Asthma clinical course show no significant improvement when other predisposing factor is not well-controlled and a child’s growth and development may be affected. Improving condition of the patient can be created with the help of loving and caring way of nurturing from the parents and supportive peer group. Therefore, continuous and consistent monitoring is required because prognosis of asthma is generally good when regularly and properly controlled.
Abstract: Twenty four New Zealand white rabbits (12 does and
12 bucks) and twenty four Flanders (12 does and 12 bucks) rabbits,
allotted into two feeding regime (6 for each breed, 3 males and 3
females) first one fed commercial ration and second one fed
commercial diet plus sodium butyrate (300 g/ton). The obtained
results showed that at end of 8th week experimental period New
Zealand white rabbits were heavier body weight than Flanders rabbits
(1934.55+39.05 vs. 1802.5+30.99 g); significantly high body weight
gain during experimental period especially during 8th week
(136.1+3.5 vs. 126.8+1.8 g/week); better feed conversion ratio during
all weeks of experiment from first week (3.07+0.16 vs. 3.12+0.10)
till the 8th week of experiment (5.54+0.16 vs. 5.76+0.07) with
significantly high dressing percentages (0.54+0.01 vs. 0.52+0.01).
Also all carcass cuts were significantly high in New Zealand white
rabbits than Flanders. Females rabbits (at the same age) were lower
body weight than males from start of experiment (941.1+39.8
vs.972.1+33.5 g) till the end of experiment (1833.64+37.69 vs.
1903.41+36.93 g); gained less during all weeks of experiment except
during 8th week (132.1+2.3 vs. 130.9+3.4 g/week), with lower
dressing percentage (0.52+0.01 vs. 0.53+0.01) and lighter carcass
cuts than males, however, they had better feed conversion ratio
during 1st week, 7th week and 8th week of experiment. Addition of
300g sodium butyrate/ton of rabbit increased the body weight of
rabbits at the end of experimental period (1882.71+26.45 vs.
1851.5+49.82 g); improve body weight gain at 3rd, 4th, 5th, 6th and
7th week of experiment and significantly improve feed conversion
ratio during all weeks of the experiment from 1st week (2.85+0.07
vs. 3.30+0.15) till the 8th week of the experiment (5.51+0.12 vs.
5.77+0.12). Also the dressing percentage was higher in Sodium
butyrate fed groups than control one (0.53+0.01 vs. 0.52+0.01) and
the most important results of feeding sodium butyrate is the reducing
of the mortality percentage in rabbits during 8 week experiment to
zero percentage as compared with 16% in control group.
Abstract: The aim of this study was to evaluate the sensitivity
of a range of EEG indices to time-on-task effects and to a workload
manipulation (cueing), during performance of a resource-limited
vigilance task. Effects of task period and cueing on performance and
subjective state response were consistent with previous vigilance
studies and with resource theory. Two EEG indices – the Task Load
Index (TLI) and global lower frequency (LF) alpha power – showed
effects of task period and cueing similar to those seen with correct
detections. Across four successive task periods, the TLI declined and
LF alpha power increased. Cueing increased TLI and decreased LF
alpha. Other indices – the Engagement Index (EI), frontal theta and
upper frequency (UF) alpha failed to show these effects. However, EI
and frontal theta were sensitive to interactive effects of task period
and cueing, which may correspond to a stronger anxiety response to
the uncued task.
Abstract: Organizations face challenges supporting knowledge
workers due to their particular requirements for an environment
supportive of their self-guided learning activities which are important
to increase their productivity and to develop creative solutions to
non-routine problems. Face-to-face knowledge sharing remains
crucial in spite of a large number of knowledge management
instruments that aim at supporting a more impersonal transfer of
knowledge. This paper first describes the main criteria for a
conceptual and technical solution targeted at flexible management of
office space that aims at assigning those knowledge workers to the
same room that are most likely to thrive when being brought together
thus enhancing their knowledge work productivity. The paper
reflects on lessons learned from the implementation and operation of
such a solution in a project-focused organization and derives several
implications for future extensions that target to foster problem
solving, informal learning and personal development.
Abstract: Heating systems are a necessity for regions which
brace extreme cold weather throughout the year. To maintain a comfortable temperature inside a given place, heating systems
making use of- Hydronic boilers- are used. The principle of a single
pipe system serves as a base for their working. It is mandatory for these heating systems to control the room temperature, thus
maintaining a warm environment. In this paper, the concept of regulation of the room temperature over a wide range is established
by using an Adaptive Fuzzy Controller (AFC). This fuzzy controller automatically detects the changes in the outside temperatures and
correspondingly maintains the inside temperature to a palatial value. Two separate AFC's are put to use to carry out this function: one to
determine the quantity of heat needed to reach the prospective temperature required and to set the desired temperature; the other to control the position of the valve, which is directly proportional to the
error between the present room temperature and the user desired temperature. The fuzzy logic controls the position of the valve as per
the requirement of the heat. The amount by which the valve opens or closes is controlled by 5 knob positions, which vary from minimum to maximum, thereby regulating the amount of heat flowing through the valve. For the given test system data, different de-fuzzifier
methods have been implemented and the results are compared. In order to validate the effectiveness of the proposed approach, a fuzzy controller has been designed by obtaining a test data from a real time
system. The simulations are performed in MATLAB and are verified with standard system data. The proposed approach can be implemented for real time applications.
Abstract: The advancement in wireless technology with the wide
use of mobile devices have drawn the attention of the research and
technological communities towards wireless environments, such as
Wireless Local Area Networks (WLANs), Wireless Wide Area
Networks (WWANs), and mobile systems and ad-hoc networks.
Unfortunately, wired and wireless networks are expressively different
in terms of link reliability, bandwidth, and time of propagation delay
and by adapting new solutions for these enhanced
telecommunications, superior quality, efficiency, and opportunities
will be provided where wireless communications were otherwise
unfeasible. Some researchers define 4G as a significant improvement
of 3G, where current cellular network’s issues will be solved and data
transfer will play a more significant role. For others, 4G unifies
cellular and wireless local area networks, and introduces new routing
techniques, efficient solutions for sharing dedicated frequency bands,
and an increased mobility and bandwidth capacity. This paper
discusses the possible solutions and enhancements probabilities that
proposed to improve the performance of Transmission Control
Protocol (TCP) over different wireless networks and also the paper
investigated each approach in term of advantages and disadvantages.
Abstract: The effect of phosphorus supplementation of ammoniated rice straw was studied. The in vitro experiment was carried out following the first stage of Tilley and Terry method. The treatments consisting of four diets were A = 50% ammoniated rice straw + 50% concentrate (control), B = A + 0.2% Phosphor (P) supplement, C = A + 0.4% Phosphor (P) supplement, and D = A + 0.6% Phosphor (P) supplement of dry matter. Completely randomized design was used as the experimental design with differences among treatment means were examined using Duncan multiple range test. Variables measured were total bacterial and cellulolytic bacterial population, cellulolytic enzyme activity, ammonia (NH3) and volatile fatty acid (VFA) concentrations, as fermentability indicators and synthesized microbial protein, as well as degradability indicators including dry matter (DM), organic matter (OM), neutral detergent fibre (NDF), acid detergent fibre (ADF) and cellulose. The results indicated that fermentability and degradability of diets consisting ammoniated rice straw with P supplementation were significantly higher than the control diet (P< 0.05). It is concluded that P supplementation is important to improve fermentability and degradability of rations containing ammoniated RS and concentrate. In terms of the most effective level of P supplementation occurred at a supplementation rate of 0.4% of dry matter.
Abstract: Case-Based Reasoning (CBR) is one of machine
learning algorithms for problem solving and learning that caught a lot
of attention over the last few years. In general, CBR is composed of
four main phases: retrieve the most similar case or cases, reuse the
case to solve the problem, revise or adapt the proposed solution, and
retain the learned cases before returning them to the case base for
learning purpose. Unfortunately, in many cases, this retain process
causes the uncontrolled case base growth. The problem affects
competence and performance of CBR systems. This paper proposes
competence-based maintenance method based on deletion policy
strategy for CBR. There are three main steps in this method. Step 1,
formulate problems. Step 2, determine coverage and reachability set
based on coverage value. Step 3, reduce case base size. The results
obtained show that this proposed method performs better than the
existing methods currently discussed in literature.
Abstract: Non-uniform current distribution in polymer
electrolyte membrane fuel cells results in local over-heating,
accelerated ageing, and lower power output than expected. This
issue is very critical when fuel cell experiences water flooding. In
this work, the performance of a PEM fuel cell is investigated under
cathode flooding conditions. Two-dimensional partially flooded
GDL models based on the conservation laws and electrochemical
relations are proposed to study local current density distributions
along flow fields over a wide range of cell operating conditions.
The model results show a direct association between cathode inlet
humidity increases and that of average current density but the
system becomes more sensitive to flooding. The anode inlet
relative humidity shows a similar effect. Operating the cell at
higher temperatures would lead to higher average current densities
and the chance of system being flooded is reduced. In addition,
higher cathode stoichiometries prevent system flooding but the
average current density remains almost constant. The higher anode
stoichiometry leads to higher average current density and higher
sensitivity to cathode flooding.
Abstract: Many water supply systems in Australia are currently
undergoing significant reconfiguration due to reductions in long term
average rainfall and resulting low inflows to water supply reservoirs
since the second half of the 20th century. When water supply systems
undergo change, it is necessary to develop new operating rules,
which should consider climate, because the climate change is likely
to further reduce inflows. In addition, water resource systems are
increasingly intended to be operated to meet complex and multiple
objectives representing social, economic, environmental and
sustainability criteria. This is further complicated by conflicting
preferences on these objectives from diverse stakeholders. This paper
describes a methodology to develop optimum operating rules for
complex multi-reservoir systems undergoing significant change,
considering all of the above issues. The methodology is demonstrated
using the Grampians water supply system in northwest Victoria,
Australia. Initial work conducted on the project is also presented in
this paper.
Abstract: Two cultivars ('Rutuliai', 'Saint Perrie') and five
hybrids ('Tolstoi', 'Brooklyn', 'Tocayo', 'Benito', 'Tourist') of edible
tomato (Lycopersicon esculentum Mill.) were investigated at the
LRCAF Institute of Horticulture. The following fruit quality
parameters were evaluated: the amount of lycopene, β-carotene,
ascorbic acid, total and inverted sugar, sucrose, dry matter soluble
solids in fresh tomato matter, also were determined fruit skin and
flesh firmness, color indexes (CIE L*a*b*) and calculated hue angle
(h°) with chroma (C).
Abstract: Renewable energy resources are inexhaustible, clean as compared with conventional resources. Also, it is used to supply regions with no grid, no telephone lines, and often with difficult accessibility by common transport. Satellite earth stations which located in remote areas are the most important application of renewable energy. Neural control is a branch of the general field of intelligent control, which is based on the concept of artificial intelligence. This paper presents the mathematical modeling of satellite earth station power system which is required for simulating the system.Aswan is selected to be the site under consideration because it is a rich region with solar energy. The complete power system is simulated using MATLAB–SIMULINK.An artificial neural network (ANN) based model has been developed for the optimum operation of earth station power system. An ANN is trained using a back propagation with Levenberg–Marquardt algorithm. The best validation performance is obtained for minimum mean square error. The regression between the network output and the corresponding target is equal to 96% which means a high accuracy. Neural network controller architecture gives satisfactory results with small number of neurons, hence better in terms of memory and time are required for NNC implementation. The results indicate that the proposed control unit using ANN can be successfully used for controlling the satellite earth station power system.
Abstract: The paper presents the results of microhardness and
microstructure of low carbon steel surface melted using carbon
dioxide laser with a wavelength of 10.6μm and a maximum output
power of 2000W. The processing parameters such as the laser power,
and the scanning rate were investigated in this study. After surface
melting two distinct regions formed corresponding to the melted zone
MZ, and the heat affected zone HAZ. The laser melted region
displayed a cellular fine structures while the HAZ displayed
martensite or bainite structure. At different processing parameters,
the original microstructure of this steel (Ferrite+Pearlite) has been
transformed to new phases of martensitic and bainitic structures. The
fine structure and the high microhardness are evidence of the high
cooling rates which follow the laser melting. The melting pool and
the transformed microstructure in the laser surface melted region of
carbon steel showed clear dependence on laser power and scanning
rate.
Abstract: Modeling and vibration of a flexible link manipulator
with tow flexible links and rigid joints are investigated which can
include an arbitrary number of flexible links. Hamilton principle and
finite element approach is proposed to model the dynamics of
flexible manipulators. The links are assumed to be deflection due to
bending. The association between elastic displacements of links is
investigated, took into account the coupling effects of elastic motion
and rigid motion. Flexible links are treated as Euler-Bernoulli beams
and the shear deformation is thus abandoned. The dynamic behavior
due to flexibility of links is well demonstrated through numerical
simulation. The rigid-body motion and elastic deformations are
separated by linearizing the equations of motion around the rigid
body reference path. Simulation results are shown on for both
position and force trajectory tracking tasks in the presence of varying
parameters and unknown dynamics remarkably well. The proposed
method can be used in both dynamic simulation and controller
design.
Abstract: In this paper, a self starting two step continuous block
hybrid formulae (CBHF) with four Off-step points is developed using
collocation and interpolation procedures. The CBHF is then used to
produce multiple numerical integrators which are of uniform order
and are assembled into a single block matrix equation. These
equations are simultaneously applied to provide the approximate
solution for the stiff ordinary differential equations. The order of
accuracy and stability of the block method is discussed and its
accuracy is established numerically.
Abstract: This study investigates the use of genetic algorithms
in information retrieval. The method is shown to be applicable to
three well-known documents collections, where more relevant
documents are presented to users in the genetic modification. In this
paper we present a new fitness function for approximate information
retrieval which is very fast and very flexible, than cosine similarity
fitness function.
Abstract: This paper study the behavior of the solution at the crack edges for an elliptical crack with developing cusps, Ω in the plane elasticity subjected to shear loading. The problem of finding the resulting shear stress can be formulated as a hypersingular integral equation over Ω and it is then transformed into a similar equation over a circular region, D, using conformal mapping. An appropriate collocation points are chosen on the region D to reduce the hypersingular integral equation into a system of linear equations with (2N+1)(N+1) unknown coefficients, which will later be used in the determination of shear stress intensity factors and maximum shear stress intensity. Numerical solution for the considered problem are compared with the existing asymptotic solution, and displayed graphically. Our results give a very good agreement to the existing asymptotic solutions.
Abstract: The purpose of this work is to establish the theoretical
foundations for calculating and designing the sublimationcondensation
processes in chemical apparatuses which are intended
for production of ultrafine powders of crystalline and amorphous
materials with controlled fractional composition. Theoretic analysis
of the primary processes of nucleation and growth kinetics of the
clusters according to the degree of super-saturation and the
homogeneous or heterogeneous nature of nucleation has been carried
out. The engineering design procedures of desublimation processes
have been offered and tested for modification of the Claus process.
Abstract: Tanzania secondary schools in rural areas are geographically and socially isolated, hence face a number of problems in getting learning materials resulting in poor performance in National examinations. E-learning as defined to be the use of information and communication technology (ICT) for supporting the educational processes has motivated Tanzania to apply ICT in its education system. There has been effort to improve secondary school education using ICT through several projects. ICT for e-learning to Tanzania rural secondary school is one of the research projects conceived by the University of Dar-es-Salaam through its College of Engineering and Technology. The main objective of the project is to develop a tool to enable ICT support rural secondary school. The project is comprehensive with a number of components, one being development of e-learning management system (e-LMS) for Tanzania secondary schools. This paper presents strategies of developing e-LMS. It shows the importance of integrating action research methodology with the modeling methods as presented by model driven architecture (MDA) and the usefulness of Unified Modeling Language (UML) on the issue of modeling. The benefit of MDA will go along with the development based on software development life cycle (SDLC) process, from analysis and requirement phase through design and implementation stages as employed by object oriented system analysis and design approach. The paper also explains the employment of open source code reuse from open source learning platforms for the context sensitive development of the e-LMS for Tanzania secondary schools.