Abstract: This paper observed the interhemispheric conjugate
auroral activity occurred on 21 September 2009. The GPS derived
ionospheric total electron content (TEC) during a weak substorm
interval recorded at interhemispheric conjugate points at Husafell in
Iceland and Syowa in Antarctica is investigated to look at their
signatures on the auroral features. Selection of all-sky camera (ASC)
images and keogram at Tjörnes and Syowa during the interval
00:47:54 – 00:50:14 UT on 21 September 2009 found that the auroral
activity had exerted their influence on the GPS TEC as a
consequence of varying interplanetary magnetic field (IMF) By
polarity.
Abstract: The available data on the cross sections of electronimpact
excitation of krypton 5s and 5p configuration levels out of the
ground state are represented in convenient and compact form. The
results are obtained by regression through all known published data
related to this process.
Abstract: This paper focuses on developing an integrated
reliable and sophisticated model for ultra large wind turbines And to
study the performance and analysis of vector control on large wind
turbines. With the advance of power electronics technology, direct
driven multi-pole radial flux PMSG (Permanent Magnet Synchronous
Generator) has proven to be a good choice for wind turbines
manufacturers. To study the wind energy conversion systems, it is
important to develop a wind turbine simulator that is able to produce
realistic and validated conditions that occur in real ultra MW wind
turbines. Three different packages are used to simulate this model,
namely, Turbsim, FAST and Simulink. Turbsim is a Full field wind
simulator developed by National Renewable Energy Laboratory
(NREL). The wind turbine mechanical parts are modeled by FAST
(Fatigue, Aerodynamics, Structures and Turbulence) code which is
also developed by NREL. Simulink is used to model the PMSG, full
scale back to back IGBT converters, and the grid.
Abstract: The introduction of sowing technologies into minimum- or no-tillage soil has a number of economical and environmental virtues, such as improving soil properties, decreasing soil erosion and degradation, and saving working time and fuel. However, the main disadvantage of these technologies is that plant residues on the soil surface reduce the quality of the planted crop seeds, thus requiring plant residues to be removed or cut. This paper presents a analysis of disc coulter parameters and an experimental investigation of cutting spring barley straw containing various amounts of moisture with different disc coulters (smooth and notched).
Abstract: In this paper we use exponential particle swarm
optimization (EPSO) to cluster data. Then we compare between
(EPSO) clustering algorithm which depends on exponential variation
for the inertia weight and particle swarm optimization (PSO)
clustering algorithm which depends on linear inertia weight. This
comparison is evaluated on five data sets. The experimental results
show that EPSO clustering algorithm increases the possibility to find
the optimal positions as it decrease the number of failure. Also show
that (EPSO) clustering algorithm has a smaller quantization error
than (PSO) clustering algorithm, i.e. (EPSO) clustering algorithm
more accurate than (PSO) clustering algorithm.
Abstract: This paper considers the development of a two-point
predictor-corrector block method for solving delay differential
equations. The formulae are represented in divided difference form
and the algorithm is implemented in variable stepsize variable order
technique. The block method produces two new values at a single
integration step. Numerical results are compared with existing
methods and it is evident that the block method performs very well.
Stability regions of the block method are also investigated.
Abstract: A novel circuit for generating a signal embedded with
features about data from three sensors is presented. This suggested
circuit is making use of a resistance-to-time converter employing a
bridge amplifier, an integrator and a comparator. The second resistive
sensor (Rz) is transformed into duty cycle. Another bridge with
varying resistor, (Ry) in the feedback of an OP AMP is added in
series to change the amplitude of the resulting signal in a proportional
relationship while keeping the same frequency and duty cycle
representing proportional changes in resistors Rx and Rz already
mentioned. The resultant output signal carries three types of
information embedded as variations of its frequency, duty cycle and
amplitude.
Abstract: The use of radar in Quantitative Precipitation Estimation (QPE) for radar-rainfall measurement is significantly beneficial. Radar has advantages in terms of high spatial and temporal condition in rainfall measurement and also forecasting. In Malaysia, radar application in QPE is still new and needs to be explored. This paper focuses on the Z/R derivation works of radarrainfall estimation based on rainfall classification. The works developed new Z/R relationships for Klang River Basin in Selangor area for three different general classes of rain events, namely low (10mm/hr, 30mm/hr) and also on more specific rain types during monsoon seasons. Looking at the high potential of Doppler radar in QPE, the newly formulated Z/R equations will be useful in improving the measurement of rainfall for any hydrological application, especially for flood forecasting.
Abstract: Power Spectral Density (PSD) of quasi-stationary processes can be efficiently estimated using the short time Fourier series (STFT). In this paper, an algorithm has been proposed that computes the PSD of quasi-stationary process efficiently using offline autoregressive model order estimation algorithm, recursive parameter estimation technique and modified sliding window discrete Fourier Transform algorithm. The main difference in this algorithm and STFT is that the sliding window (SW) and window for spectral estimation (WSA) are separately defined. WSA is updated and its PSD is computed only when change in statistics is detected in the SW. The computational complexity of the proposed algorithm is found to be lesser than that for standard STFT technique.
Abstract: Dual phase steels (DPS)s have a microstructure
consisting of a hard second phase called Martensite in the soft Ferrite
matrix. In recent years, there has been interest in dual-phase steels,
because the application of these materials has made significant usage;
particularly in the automotive sector Composite microstructure of
(DPS)s exhibit interesting characteristic mechanical properties such
as continuous yielding, low yield stress to tensile strength
ratios(YS/UTS), and relatively high formability; which offer
advantages compared with conventional high strength low alloy
steels(HSLAS). The research dealt with the characterization of
damage in (DPS)s. In this study by review the mechanisms of failure
due to volume fraction of martensite second phase; a new method is
introduced to identifying the mechanisms of failure in the various
phases of these types of steels. In this method the acoustic emission
(AE) technique was used to detect damage progression. These failure
mechanisms consist of Ferrite-Martensite interface decohesion and/or
martensite phase fracture. For this aim, dual phase steels with
different volume fraction of martensite second phase has provided by
various heat treatment methods on a low carbon steel (0.1% C), and
then AE monitoring is used during tensile test of these DPSs. From
AE measurements and an energy ratio curve elaborated from the
value of AE energy (it was obtained as the ratio between the strain
energy to the acoustic energy), that allows detecting important
events, corresponding to the sudden drops. These AE signals events
associated with various failure mechanisms are classified for ferrite
and (DPS)s with various amount of Vm and different martensite
morphology. It is found that AE energy increase with increasing Vm.
This increasing of AE energy is because of more contribution of
martensite fracture in the failure of samples with higher Vm. Final
results show a good relationship between the AE signals and the
mechanisms of failure.
Abstract: Road signs are the elements of roads with a lot of
influence in driver-s behavior. So that signals can fulfill its function,
they must overcome visibility and durability requirements,
particularly needed at night, when the coefficient of retroreflection
becomes a decisive factor in ensuring road safety. Accepting that the
visibility of the signage has implications for people-s safety, we
understand the importance to fulfill its function: to foster the highest
standards of service and safety in drivers. The usual conditions of
perception of any sign are determined by: age of the driver, reflective
material, luminosity, vehicle speed and emplacement. In this way,
this paper evaluates the different signals to increase the safety road.
Abstract: The main objective of this project is to build an
autonomous microcontroller-based mobile robot for a local robot
soccer competition. The black competition field is equipped with
white lines to serve as the guidance path for competing robots. Two
prototypes of soccer robot embedded with the Basic Stamp II
microcontroller have been developed. Two servo motors are used as
the drive train for the first prototype whereas the second prototype
uses two DC motors as its drive train. To sense the lines, lightdependent
resistors (LDRs) supply the analog inputs for the
microcontroller. The performances of both prototypes are evaluated.
The DC motor-driven robot has produced better trajectory control
over the one using servo motors and has brought the team into the
final round.
Abstract: The purpose of this work is measurement of the
system presampling MTF of a variable resolution x-ray (VRX) CT
scanner. In this paper, we used the parameters of an actual VRX CT
scanner for simulation and study of effect of different focal spot sizes
on system presampling MTF by Monte Carlo method (GATE
simulation software). Focal spot size of 0.6 mm limited the spatial
resolution of the system to 5.5 cy/mm at incident angles of below 17º
for cell#1. By focal spot size of 0.3 mm the spatial resolution
increased up to 11 cy/mm and the limiting effect of focal spot size
appeared at incident angles of below 9º. The focal spot size of 0.3
mm could improve the spatial resolution to some extent but because
of magnification non-uniformity, there is a 10 cy/mm difference
between spatial resolution of cell#1 and cell#256. The focal spot size
of 0.1 mm acted as an ideal point source for this system. The spatial
resolution increased to more than 35 cy/mm and at all incident angles
the spatial resolution was a function of incident angle. By the way
focal spot size of 0.1 mm minimized the effect of magnification nonuniformity.
Abstract: This paper presents the applicability of artificial
neural networks for 24 hour ahead solar power generation forecasting
of a 20 kW photovoltaic system, the developed forecasting is suitable
for a reliable Microgrid energy management. In total four neural
networks were proposed, namely: multi-layred perceptron, radial
basis function, recurrent and a neural network ensemble consisting in
ensemble of bagged networks. Forecasting reliability of the proposed
neural networks was carried out in terms forecasting error
performance basing on statistical and graphical methods. The
experimental results showed that all the proposed networks achieved
an acceptable forecasting accuracy. In term of comparison the neural
network ensemble gives the highest precision forecasting comparing
to the conventional networks. In fact, each network of the ensemble
over-fits to some extent and leads to a diversity which enhances the
noise tolerance and the forecasting generalization performance
comparing to the conventional networks.
Abstract: Online news websites are one of the main and wide areas of Mass Media. Since the nineties several Jordanian newspapers were introduced to the World Wide Web to reach various and large numbers of audiances. Examples of these newspapers that have online version are Al-Rai, Ad-Dustor and AlGhad. Other pure online news websites include Ammon and Rum. The main aim of this study is to evaluate online newspaper websites using two assessment measures; usability and web content. This aim is achieved by using a questionnaire based evaluation which is based on the definition of usability and web content in the ISO document as the standard number 9241-part 11. The results are obtained based on 204 audiences- responses. The results of the research showed that the usability factor is relatively good for all Jordanian online newspapers whereas the web content factor is moderate.
Abstract: Attitude control of aerospace system with liquid containers may face to a problem associate with fuel sloshing. The sloshing phenomena can degrade the stability of control system and in the worst case, interaction between the attitude control system and fuel vibration leading to resonance. In this paper, a full process of nonlinear dynamic modeling of an aerospace launch vehicle with fuel sloshing is given. Then, a new control system based on model reference adaptive filter is proposed and its algorithm is extracted. This controller implemented on the main attitude control system. Finally, numerical simulation of nonlinear model and control system is carried out to examine the performance of the new controller. Results of simulations show that the inconvenient effects of the fuel sloshing by augmenting this control system are reduced and attitude control system performs, satisfactorily.
Abstract: Nowadays, butyl acetate, a pineapple flavor has been applied widely in food, beverage, cosmetic and pharmaceutical industries. In this study, Butyl acetate, a flavor ester was successfully synthesized via green synthesis of enzymatic reaction route. Commercial immobilized lipase from Rhizomucor miehei (Lipozyme RMIM) was used as biocatalyst in the esterification reaction between acetic acid and butanol. Various reaction parameters such as reaction time (RT), temperature (T) and amount of enzyme (E) were chosen to optimize the reaction synthesis in solvent-free system. The optimum condition to produce butyl acetate was at reaction time (RT), 18 hours; temperature (T), 37°C and amount of enzyme, 25 % (w/w of total substrate). Analysis of yield showed that at optimum condition, >78 % of butyl acetate was produced. The product was confirmed as butyl acetate from FTIR analysis whereby the presence of an ester group was observed at wavenumber of 1742 cm-1.
Abstract: This work relates the development of an optical fiber
(OF) sensor for the detection and quantification of single walled
carbon nanotubes in aqueous solutions. The developed OF displays a
compact design, it requires less expensive materials and equipment
as well as low volume of sample (0.2 mL). This methodology was
also validated by the comparison of its analytical performance with
that of a standard methodology based on ultraviolet-visible
spectroscopy. The developed OF sensor follows the general SDS
calibration proposed for OF sensors as a more suitable calibration
fitting compared with classical calibrations.
Abstract: The new technology of fuzzy neural networks for identification of parameters for mathematical models of geofields is proposed and checked. The effectiveness of that soft computing technology is demonstrated, especially in the early stage of modeling, when the information is uncertain and limited.
Abstract: There is growing interest in biodiesel (fatty acid
methyl ester or FAME) because of the similarity in its properties
when compared to those of diesel fuels. Diesel engines operated on
biodiesel have lower emissions of carbon monoxide, unburned
hydrocarbons, particulate matter, and air toxics than when operated
on petroleum-based diesel fuel. Production of fatty acid methyl ester
(FAME) from rapeseed (nonedible oil) fatty acid distillate having
high free fatty acids (FFA) was investigated in this work. Conditions
for esterification process of rapeseed oil were 1.8 % H2SO4 as
catalyst, MeOH/oil of molar ratio 2 : 0.1 and reaction temperature
65 °C, for a period of 3h. The yield of methyl ester was > 90 % in 1
h.
The amount of FFA was reduced from 93 wt % to less than 2 wt %
at the end of the esterification process. The FAME was pureed by
neutralization with 1 M sodium hydroxide in water solution at a
reaction temperature of 62 °C. The final FAME product met with the
biodiesel quality standard, and ASTM D 6751.