Abstract: Nowadays, the focus on renewable energy and alternative fuels has increased due to increasing oil prices, environment pollution, and also concern on preserving the nature. Biodiesel has been known as an attractive alternative fuel although biodiesel produced from edible oil is very expensive than conventional diesel. Therefore, the uses of biodiesel produced from non-edible oils are much better option. Currently Jatropha biodiesel (JBD) is receiving attention as an alternative fuel for diesel engine. Biodiesel is non-toxic, biodegradable, high lubricant ability, highly renewable, and its use therefore produces real reduction in petroleum consumption and carbon dioxide (CO2) emissions. Although biodiesel has many advantages, but it still has several properties need to improve, such as lower calorific value, lower effective engine power, higher emission of nitrogen oxides (NOX) and greater sensitivity to low temperature. Exhaust gas recirculation (EGR) is effective technique to reduce NOX emission from diesel engines because it enables lower flame temperature and oxygen concentration in the combustion chamber. Some studies succeeded to reduce the NOX emission from biodiesel by EGR but they observed increasing soot emission. The aim of this study was to investigate the engine performance and soot emission by using blended Jatropha biodiesel with different EGR rates. A CI engine that is water-cooled, turbocharged, using indirect injection system was used for the investigation. Soot emission, NOX, CO2, carbon monoxide (CO) were recorded and various engine performance parameters were also evaluated.
Abstract: Fuzzy sets theory affirmed that the linguistic value for
every contraries relation is complementary. It was stressed in the
intuitionistic fuzzy sets (IFS) that the conditions for contraries
relations, which are the fuzzy values, cannot be greater than one.
However, complementary in two contradict phenomena are not
always true. This paper proposes a new idea condition for conflicting
bifuzzy sets by relaxing the condition of intuitionistic fuzzy sets.
Here, we will critically forward examples using triangular fuzzy
number in formulating a new condition for conflicting bifuzzy sets
(CBFS). Evaluation of positive and negative in conflicting
phenomena were calculated concurrently by relaxing the condition in
IFS. The hypothetical illustration showed the applicability of the new
condition in CBFS for solving non-complement contraries
intuitionistic evaluation. This approach can be applied to any
decision making where conflicting is very much exist.
Abstract: According to development of communications and
web-based technologies in recent years, e-Learning has became very
important for everyone and is seen as one of most dynamic teaching
methods.
Grid computing is a pattern for increasing of computing power
and storage capacity of a system and is based on hardware and
software resources in a network with common purpose. In this article
we study grid architecture and describe its different layers. In this
way, we will analyze grid layered architecture. Then we will
introduce a new suitable architecture for e-Learning which is based
on grid network, and for this reason we call it Grid Learning
Architecture. Various sections and layers of suggested architecture
will be analyzed; especially grid middleware layer that has key role.
This layer is heart of grid learning architecture and, in fact,
regardless of this layer, e-Learning based on grid architecture will
not be feasible.
Abstract: In this paper a study on the vibration of thin
cylindrical shells with ring supports and made of functionally graded
materials (FGMs) composed of stainless steel and nickel is presented.
Material properties vary along the thickness direction of the shell
according to volume fraction power law. The cylindrical shells have
ring supports which are arbitrarily placed along the shell and impose
zero lateral deflections. The study is carried out based on third order
shear deformation shell theory (T.S.D.T). The analysis is carried out
using Hamilton-s principle. The governing equations of motion of
FGM cylindrical shells are derived based on shear deformation
theory. Results are presented on the frequency characteristics,
influence of ring support position and the influence of boundary
conditions. The present analysis is validated by comparing results
with those available in the literature.
Abstract: Steroidal hormones with the efficient changes on the epiphyseal growth plate may influence tissue structure properties. Presents paper to investigate the effects of gonadectomy in the pattern distribution of the epiphyseal structure. Fifteen adult female New Zealand white rabbits were separated into three groups. One group was intact and others groups were selected for surgical operation. From these two groups, one group carried out steroidal administration. The results obtained showed that there is no statistically difference in the mean diameter of the growth plate cells between all three groups. The maximum value of the cartilage cells were allocated to the gonadectomized group and the minimum number were observed in Hormonal induced group significantly. Growth plate height was significantly greater in gonadectomized group than in two other groups.
Abstract: Today due to rising levels of housing- necessities,
several problems have been raised regarding to urban quality of life.
The aim of the research is to study social and spatial aspects of
housing environment and to find out their interaction with the urban
quality of life. As a case of study two pilot areas of Famagusta city in
North Cyprus, were selected: Baykal, considered as an established
urban district and Tuzla, a newly developed peri-urban district. In
order to determine urban quality of life in planning and developing of
housing areas, social and spatial aspects of selected areas have been
examined, differences between them according to the planning policy
have been pointed out, advantages and disadvantages of housing
planning have been found. As a practical implementation of the
research a number of households in each selected area have been
interviewed in order to draw a conclusion.
Abstract: As it is known, buoyancy and drag forces rule bubble's rise velocity in a liquid column. These forces are strongly dependent on fluid properties, gravity as well as equivalent's diameter. This study reports a set of bubble rising velocity experiments in a liquid column using water or glycerol. Several records of terminal velocity were obtained. The results show that bubble's rise terminal velocity is strongly dependent on dynamic viscosity effect. The data set allowed to have some terminal velocities data interval of 8.0 ? 32.9 cm/s with Reynolds number interval 1.3 -7490. The bubble's movement was recorded with a video camera. The main goal is to present an original set data and results that will be discussed based on two-phase flow's theory. It will also discussed, the prediction of terminal velocity of a single bubble in liquid, as well as the range of its applicability. In conclusion, this study presents general expressions for the determination of the terminal velocity of isolated gas bubbles of a Reynolds number range, when the fluid proprieties are known.
Abstract: This paper presents a numerical study on surface heat
transfer characteristics of laminar air flows in parallel-plate dimpled
channels. The two-dimensional numerical model is provided by
commercial code FLUENT and the results are obtained for channels
with symmetrically opposing hemi-cylindrical cavities onto both
walls for Reynolds number ranging from 1000 to 2500. The influence
of variations in relative depth of dimples (the ratio of cavity depth to
the cavity curvature diameter), the number of them and the thermophysical
properties of channel walls on heat transfer enhancement is
studied. The results are evident for existence of an optimum value for
the relative depth of dimples in which the largest wall heat flux and
average Nusselt number can be achieved. In addition, the results of
conjugation simulation indicate that the overall influence of the ratio
of wall thermal conductivity to the one of the fluid on heat transfer
rate is not much significant and can be ignored.
Abstract: This article presents a numerical study of the doublediffusive
mixed convection in a vertical channel filled with porous
medium by using non-equilibrium model. The flow is assumed
fully developed, uni-directional and steady state. The controlling
parameters are thermal Rayleigh number (RaT ), Darcy number (Da),
Forchheimer number (F), buoyancy ratio (N), inter phase heat transfer
coefficient (H), and porosity scaled thermal conductivity ratio
(γ). The Brinkman-extended non-Darcy model is considered. The
governing equations are solved by spectral collocation method. The
main emphasize is given on flow profiles as well as heat and solute
transfer rates, when two diffusive components in terms of buoyancy
ratio are in favor (against) of each other and solid matrix and fluid
are thermally non-equilibrium. The results show that, for aiding flow
(RaT = 1000), the heat transfer rate of fluid (Nuf ) increases upto a
certain value of H, beyond that decreases smoothly and converges
to a constant, whereas in case of opposing flow (RaT = -1000),
the result is same for N = 0 and 1. The variation of Nuf in (N,
Nuf )-plane shows sinusoidal pattern for RaT = -1000. For both cases
(aiding and opposing) the flow destabilize on increasing N by inviting
point of inflection or flow separation on the velocity profile. Overall,
the buoyancy force have significant impact on the non-Darcy mixed
convection under LTNE conditions.
Abstract: In this work, an attempt is made to design an optimal
wind/pv/diesel hybrid power system for a village of Ain Merane,
Chlef, Algeria, where the wind speed and solar radiation
measurements were made. The aim of this paper is the optimization
of a hybrid wind/solar/diesel system applied in term of technical and
economic feasibility by simulation using HOMER. A comparison
was made between the performance of wind/pv/diesel system and the
classic connecting system.
Abstract: A multiple-option analytical model for the evaluation of the energy performance and distribution of aerodynamic forces acting on a vertical-axis Darrieus wind turbine depending on both rotor architecture and operating conditions is presented. For this purpose, a numerical algorithm, capable of generating the desired rotor conformation depending on design geometric parameters, is coupled to a Single/Double-Disk Multiple-Streamtube Blade Element – Momentum code. Both single and double-disk configurations are analyzed and model predictions are compared to literature experimental data in order to test the capability of the code for predicting rotor performance. Effective airfoil characteristics based on local blade Reynolds number are obtained through interpolation of literature low-Reynolds airfoil databases. Some corrections are introduced inside the original model with the aim of simulating also the effects of blade dynamic stall, rotor streamtube expansion and blade finite aspect ratio, for which a new empirical relationship to better fit the experimental data is proposed. In order to predict also open field rotor operation, a freestream wind shear profile is implemented, reproducing the effect of atmospheric boundary layer.
Abstract: Breast cancer is the most common malignancy in the
world among women. Many therapies have been designed to treat
this disease. Mamectomy, chemotherapy and radiotherapy are still
the main therapies of breast cancer. However, the results were
unsatisfactory and still far from the ideal treatment.
PM 701is a natural product, has anticancer activity. The bioactive
fraction PMF and subfraction PMFK had been isolated from PM701.
PM 701 and its fractions were proved to have a cytotoxic properties
against different cancer cell lines. This article is directed for the
further examination of lyophilized PM701 and its active fractions on
the growth of breast cancer cells (MCF-7). PM 701, PMF or PMFK
were adding to the cultural medium, where MCF-7 is incubated.
PM 701, PMF or PMFK were able to inhibit significantly the
proliferation of MCF-7 cells, Moreover these new agents were
proved to induce apoptosis of the breast cancer cells; through its
direct effect on the nuclei.
Abstract: A unique combination of adsorption and
electrochemical regeneration with a proprietary adsorbent material
called Nyex 100 was introduced at the University of Manchester for
waste water treatment applications. Nyex 100 is based on graphite
intercalation compound. It is non porous and electrically conducing
adsorbent material. This material exhibited very small BET surface
area i.e. 2.75 m2g-1, in consequence, small adsorptive capacities for
the adsorption of various organic pollutants were obtained. This work
aims to develop composite adsorbent material essentially capable of
electrochemical regeneration coupled with improved adsorption
characteristics. An organic dye, acid violet 17 was used as standard
organic pollutant. The developed composite material was
successfully electrochemically regenerated using a DC current of 1 A
for 60 minutes. Regeneration efficiency was maintained at around
100% for five adsorption-regeneration cycles.
Abstract: Abai Kunanbayev is famous for being enlightener,
composer, interpreter, social agent, philosopher, reformer, who
wanted to enrich Kazakh literature by emergence with Russian and
European culture, and also as a founder of Kazakh written literary
language. Abai Kunanbayev was born in 1845 in East Kazakhstan
area and passed away in 1904 in his hometown. His oeuvre absorbed
and reflected all changes in the life of Kazakh society of the second
half of XIX century. Because ХІХ century, especially its second half,
was an important transition period for Kazakhstan, which radically
changed traditional way of Kazakh society and predetermined further
development in consequence of activation of Russian colonial policy
and approval of commodity-money relations in Steppe Land.Abai
Kunanbayev, besides Arabic and Persian common words and
loanwords from Quran in his words of edification, had used a lot of
words of Arabic, Persian, Latin, Russian, Nogai, Shaghatai, Polish,
Greek, Turkish, which are used in the Kazakh language.
Abstract: Despite many success stories of manufacturing safety, many organizations are still reluctant, perceiving it as cost increasing and time consuming. The clear contributor may be due to the use of lagging indicators rather than leading indicator measures. The study therefore proposes a combinatorial model for determining the best safety strategy. A combination theory and cost benefit analysis was employed to develop a monetary saving / loss function in terms value of preventions and cost of prevention strategy. Documentations, interviews and structured questionnaire were employed to collect information on Before-And-After safety programme records from a Tobacco company between periods of 1993-2001(for pre-safety) and 2002-2008 (safety period) for the model application. Three combinatorial alternatives A, B, C were obtained resulting into 4, 6 and 4 strategies respectively with PPE and Training being predominant. A total of 728 accidents were recorded for a 9 year period of pre-safety programme and 163 accidents were recorded for 7 years period of safety programme. Six preventions activities (alternative B) yielded the best results. However, all the years of operation experienced except year 2004. The study provides a leading resources for planning successful safety programme
Abstract: The purpose of this study was to determine the
influence of physical activity and dietary fat intake on Body Mass
Index (BMI) of lecturers within a higher learning institutionalized
setting. The study adopted a Cross-sectional Correlational Design
and included 120 lecturers selected proportionately by simple
random sampling techniques from a population of 600 lecturers. Data
was collected using questionnaires, which had sections including
physical activity checklist adopted from the international physical
activity questionnaire (IPAQ), 24-hour food recall, anthropometric
measurements mainly weight and height. Analysis involved the use
of bivariate correlations and linear regression. A significant inverse
association was registered between BMI and duration (in minutes)
spent doing moderate intense physical activity per day (r=-0.322,
p
Abstract: The influence of extrusion parameters on surface
quality and properties of AA6061+x% vol. SiC (x = 0; 2,5; 5; 7,5;10)
composites was discussed in this paper. The averages size of
AA6061 and SiC particles were 10.6 μm and 0.42 μm, respectively.
Two series of composites (I - compacts were preheated at extrusion
temperature through 0.5 h and cooled by water directly after process;
II - compacts were preheated through 3 hours and were not cooled)
were consolidated via powder metallurgy processing and extruded by
KoBo method. High values of density for both series of composites
were achieved. Better surface quality was observed for II series of
composites. Moreover, for these composites lower (compared to I
series) but more uniform strength properties over the cross-section of
the bar were noticed. Microstructure and Young-s modulus
investigations were made.
Abstract: The dispersion of heavy particles line in an isotropic
and incompressible three-dimensional turbulent flow has been
studied using the Kinematic Simulation techniques to find out the
evolution of the line fractal dimension. In this study, the fractal
dimension of the line is found for different cases of heavy particles
inertia (different Stokes numbers) in the absence of the particle
gravity with a comparison with the fractal dimension obtained in the
diffusion case of material line at the same Reynolds number. It can
be concluded for the dispersion of heavy particles line in turbulent
flow that the particle inertia affect the fractal dimension of a line
released in a turbulent flow for Stokes numbers 0.02 < St < 2. At the
beginning for small times, most of the different cases are not affected
by the inertia until a certain time, the particle response time τa, with
larger time as the particles inertia increases, the fractal dimension of
the line increases owing to the particles becoming more sensitive to
the small scales which cause the change in the line shape during its
journey.
Abstract: Optical Bursts Switching (OBS) is a relatively new
optical switching paradigm. Contention and burst loss in OBS
networks are major concerns. To resolve contentions, an interesting
alternative to discarding the entire data burst is to partially drop the
burst. Partial burst dropping is based on burst segmentation concept
that its implementation is constrained by some technical challenges,
besides the complexity added to the algorithms and protocols on both
edge and core nodes. In this paper, the burst segmentation concept is
investigated, and an implementation scheme is proposed and
evaluated. An appropriate dropping policy that effectively manages
the size of the segmented data bursts is presented. The dropping
policy is further supported by a new control packet format that
provides constant transmission overhead.
Abstract: Different agricultural waste peels were assessed for
their suitability to be used as primary substrates for the
bioremediation of free cyanide (CN-) by a cyanide-degrading fungus
Aspergillus awamori isolated from cyanide containing wastewater.
The bioremediated CN- concentration were in the range of 36 to 110
mg CN-/L, with Orange (C. sinensis) > Carrot (D. carota) > Onion
(A. cepa) > Apple (M. pumila), being chosen as suitable substrates
for large scale CN- degradation processes due to: 1) the high
concentration of bioremediated CN-, 2) total reduced sugars released
into solution to sustain the biocatalyst, and 3) minimal residual NH4-
N concentration after fermentation. The bioremediation rate constants
(k) were 0.017h-1 (0h < t < 24h), with improved bioremediation rates
(0.02189h-1) observed after 24h. The averaged nitrilase activity was
~10 U/L.