Abstract: Phytotoxicity of Daphne gnidium L. was evaluated
through the effect of incorporating leaves, stems and roots biomass
into soil (at 12.5, 25, 50g/Kg) and irrigation by their aqueous extracts
(50g/L), on the growth of two crops (Lactuca sativa L. and Raphanus
sativus L.) and two weeds (Peaganum harmala L. and Scolymus
maculatus L.). Results revealed a perceptible phytotoxic effect which
increased with dose and concentration. At the highest dose, roots and
leaves residues was the most toxic and caused total inhibition
respectively, for lettuce and thistle seedling growth. Irrigation with
aqueous extracts of D. gnidium different organs decreased also
seedlings length of all test species. Stems extract was more inhibitor
on thistle than peganum seedling growth; it induced a significant
reduction of 80% and 67%, for, respectively, roots and shoots.
Results of the present study suggest that different organs of D.
gnidium could be exploited in the management of agro-ecosystems.
Abstract: High Strength Concrete (HSC) is defined as concrete
that meets special combination of performance and uniformity
requirements that cannot be achieved routinely using conventional
constituents and normal mixing, placing, and curing procedures. It is
a highly complex material, which makes modeling its behavior a very
difficult task. This paper aimed to show possible applicability of
Neural Networks (NN) to predict the slump in High Strength
Concrete (HSC). Neural Network models is constructed, trained and
tested using the available test data of 349 different concrete mix
designs of High Strength Concrete (HSC) gathered from a particular
Ready Mix Concrete (RMC) batching plant. The most versatile
Neural Network model is selected to predict the slump in concrete.
The data used in the Neural Network models are arranged in a format
of eight input parameters that cover the Cement, Fly Ash, Sand,
Coarse Aggregate (10 mm), Coarse Aggregate (20 mm), Water,
Super-Plasticizer and Water/Binder ratio. Furthermore, to test the
accuracy for predicting slump in concrete, the final selected model is
further used to test the data of 40 different concrete mix designs of
High Strength Concrete (HSC) taken from the other batching plant.
The results are compared on the basis of error function (or
performance function).
Abstract: Detection of human emotions has many potential applications. One of application is to quantify attentiveness audience in order evaluate acoustic quality in concern hall. The subjective audio preference that based on from audience is used. To obtain fairness evaluation of acoustic quality, the research proposed system for multimodal emotion detection; one modality based on brain signals that measured using electroencephalogram (EEG) and the second modality is sequences of facial images. In the experiment, an audio signal was customized which consist of normal and disorder sounds. Furthermore, an audio signal was played in order to stimulate positive/negative emotion feedback of volunteers. EEG signal from temporal lobes, i.e. T3 and T4 was used to measured brain response and sequence of facial image was used to monitoring facial expression during volunteer hearing audio signal. On EEG signal, feature was extracted from change information in brain wave, particularly in alpha and beta wave. Feature of facial expression was extracted based on analysis of motion images. We implement an advance optical flow method to detect the most active facial muscle form normal to other emotion expression that represented in vector flow maps. The reduce problem on detection of emotion state, vector flow maps are transformed into compass mapping that represents major directions and velocities of facial movement. The results showed that the power of beta wave is increasing when disorder sound stimulation was given, however for each volunteer was giving different emotion feedback. Based on features derived from facial face images, an optical flow compass mapping was promising to use as additional information to make decision about emotion feedback.
Abstract: The study of the fouling deposition of pink guava
juice (PGJ) is relatively new research compared to milk fouling
deposit. In this work, a new experimental set-up was developed to
imitate the fouling formation in heat exchanger, namely a continuous
flow experimental set-up heat exchanger. The new experimental setup
was operated under industrial pasteurization temperature of PGJ,
which was at 93°C. While the flow rate and pasteurization period
were based on the experimental capacity, which were 0.5 and 1
liter/min for the flow rate and the pasteurization period was set for 1
hour. Characterization of the fouling deposit was determined by
using various methods. Microstructure of the deposits was carried
out using ESEM. Proximate analyses were performed to determine
the composition of moisture, fat, protein, fiber, ash and carbohydrate
content. A study on the hardness and stickiness of the fouling deposit
was done using a texture analyzer. The presence of seedstone in pink
guava juice was also analyzed using a particle analyzer. The findings
shown that seedstone from pink guava juice ranging from 168 to
200μm and carbohydrate was found to be a major composition
(47.7% of fouling deposit consists of carbohydrate). Comparison
between the hardness and stickiness of the deposits at two different
flow rates showed that fouling deposits were harder and denser at
higher flow rate. Findings from this work provide basis knowledge
for further study on fouling and cleaning of PGJ.
Abstract: Motion detection is very important in image
processing. One way of detecting motion is using optical flow.
Optical flow cannot be computed locally, since only one independent
measurement is available from the image sequence at a point, while
the flow velocity has two components. A second constraint is needed.
The method used for finding the optical flow in this project is
assuming that the apparent velocity of the brightness pattern varies
smoothly almost everywhere in the image. This technique is later
used in developing software for motion detection which has the
capability to carry out four types of motion detection. The motion
detection software presented in this project also can highlight motion
region, count motion level as well as counting object numbers. Many
objects such as vehicles and human from video streams can be
recognized by applying optical flow technique.
Abstract: The purpose of this work is to identify the positive and negative aspects of parties- participation in the country-s modernization, which in turn, will help a country to determine the necessary steps to improve the social-economic development. The article considers a question of the role of the dominating party of Kazakhstan and ruling party of China in the country-s modernization. Using a comparative analysis reveals differences between the People's Democratic Party “Nur Otan" and the Communist Party of China. It is discussed the policy of carrying out of modernization, the main actions of political parties of both countries with a view of modernization implementation.
Abstract: In this paper, a novel scheme is proposed for ownership identification and authentication using color images by deploying Cryptography and Digital Watermarking as underlaying technologies. The former is used to compute the contents based hash and the latter to embed the watermark. The host image that will claim to be the rightful owner is first transformed from RGB to YST color space exclusively designed for watermarking based applications. Geometrically YS ÔèÑ T and T channel corresponds to the chrominance component of color image, therefore suitable for embedding the watermark. The T channel is divided into 4×4 nonoverlapping blocks. The size of block is important for enhanced localization, security and low computation. Each block along with ownership information is then deployed by SHA160, a one way hash function to compute the content based hash, which is always unique and resistant against birthday attack instead of using MD5 that may raise the condition i.e. H(m)=H(m'). The watermark payload varies from block to block and computed by the variance factorα . The quality of watermarked images is quite high both subjectively and objectively. Our scheme is blind, computationally fast and exactly locates the tampered region.
Abstract: Agricultural residue such as oil palm fronds (OPF) is
cheap, widespread and available throughout the year. Hemicelluloses
extracted from OPF can be hydrolyzed to their monomers and used in
production of xylooligosaccharides (XOs). The objective of the
present study was to optimize the enzymatic hydrolysis process of
OPF hemicellulose by varying pH, temperature, enzyme and substrate
concentration for production of XOs. Hemicelluloses was extracted
from OPF by using 3 M potassium hydroxide (KOH) at temperature of
40°C for 4 hrs and stirred at 400 rpm. The hemicellulose was then
hydrolyzed using Trichoderma longibrachiatum xylanase at different
pH, temperature, enzyme and substrate concentration. XOs were
characterized based on reducing sugar determination. The optimum
conditions to produced XOs from OPF hemicellulose was obtained at
pH 4.6, temperature of 40°C , enzyme concentration of 2 U/mL and
2% substrate concentration. The results established the suitability of
oil palm fronds as raw material for production of XOs.
Abstract: The coastal sediments of West Port of Malaysia was monitored from Nov. 2009 to Oct. 2010 to assess spatial distribution of heavy metals As, Cu, Cd, Cr, Hg, Ni, Zn and Pb. Sediment samples were collected from 10 stations in dry and rainy season in West Port. The range concentrations measured (Mg/g dry weight ) were from 23.4 to 98.3 for Zn, 22.3 to 80 for Pb, 7.4 to 27.6 Cu, 0.244 to 3.53 for Cd, 7.2 to 22.2 for Ni, 20.2 to 162 for As, 0.11 to 0.409 for Hg and 11.5 to 61.5 for Cr. The geochemical indexes used in this study were Geoaccumulation (Igeo), Contamination Factor (CF) and Pollution Load Index (PLI); these indexes were used to evaluate the levels of sediment contaminations. The results of these indexes show that, the status of West Port sediment quality are moderately polluted by heavy metals except in arsenic which shows the high level of pollution.
Abstract: The quality and shelf life of foods of containing lipids (fats and oils) significantly reduces due to rancidity.Applications of natural antioxidants are one of the most effective manners to prevent the oxidation of oils and lipids. The antioxidant properties of juice extracted from barberry fruit (Berberris vulgaris.L) using maceration and SWE (10 bars and 120 - 180°C) methods were investigated and compared with conventional method. The amount of phenolic compound and reduction power of all samples were determined and the data were statistically analyzed using multifactor design. The results showed that the total amount of phenolic compound increased with increasing of pressure and temprature from 1861.9 to 2439.1 (mg Gallic acid /100gr Dry matter). The ability of reduction power of SWE obtained antioxidant extract compared with BHA (synthetic antioxidant) and ascorbic acid (natural antioxidant). There were significant differences among reduction power of extracts and there were remarkable difference with BHA and Ascorbic acid (P
Abstract: Photoselective plastic films with thermic properties
are now available so that greenhouses clad with such plastics exhibit
a higher degree of “Greenhouse Effect” with a consequent increase in
night time temperature. In this study, we investigate the potential
benefits of a range of thermic plastic films used as greenhouse cover
materials on the vegetative and reproductive growth and development
of Iceberg lettuce (Lactuca sativa L). Transplants were grown under
thermic films and destructively harvested 4, 5, and 6 weeks after
transplanting. Thermic films can increase night temperatures up to 2
⁰C reducing the wide fluctuation in greenhouse temperature during
winter compared to the standard commercial film and consequently
increased the yield (leaf number, fresh weight, and dry weight) of
lettuce plants. Lettuce plants grown under Clear film respond to cold
stress by the accumulation of secondary products (phenolics, and
flavonoids).
Abstract: The control design for unmanned underwater vehicles (UUVs) is challenging due to the uncertainties in the complex dynamic modeling of the vehicle as well as its unstructured operational environment. To cope with these difficulties, a practical robust control is therefore desirable. The paper deals with the application of coefficient diagram method (CDM) for a robust control design of an autonomous underwater vehicle. The CDM is an algebraic approach in which the characteristic polynomial and the controller are synthesized simultaneously. Particularly, a coefficient diagram (comparable to Bode diagram) is used effectively to convey pertinent design information and as a measure of trade-off between stability, response speed and robustness. In the polynomial ring, Kharitonov polynomials are employed to analyze the robustness of the controller due to parametric uncertainties.
Abstract: In order to increase in chickpea quality and
agroecosystem sustainability, field experiments were carried out in
2007 and 2008 growing seasons. In this research the effects of
different organic, chemical and biological fertilizers were
investigated on grain yield and quality of chickpea. Experimental
units were arranged in split-split plots based on randomized complete
blocks with three replications. The highest amounts of yield and yield
components were obtained in G1×N5 interaction. Significant
increasing of N, P, K, Fe and Mg content in leaves and grains
emphasized on superiority of mentioned treatment because each one
of these nutrients has an approved role in chlorophyll synthesis and
photosynthesis ability of the crop. The combined application of
compost, farmyard manure and chemical phosphorus (N5) had the
best grain quality due to high protein, starch and total sugar contents,
low crude fiber and reduced cooking time.
Abstract: Laser beam forming is a novel technique developed for the joining of metallic components. In this study, an overview of the laser beam forming process, areas of application, the basic mechanisms of the laser beam forming process, some recent research
studies and the need to focus more research effort on improving the
laser-material interaction of laser beam forming of titanium and its
alloys are presented.
Abstract: Three dimensional simulations are carried out to estimate the effect of wind direction, wind speed and geometry on the flow and dispersion of vehicular pollutant in a street canyon. The pollutant sources are motor vehicles passing between the two buildings. Suitable emission factors for petrol and diesel vehicles at varying vehicle speed are used for the estimation of the rate of emission from the streets. The dispersion of automobile pollutant released from the street is simulated by introducing vehicular emission source term as a fixed-flux boundary condition at the ground level over the road. The emission source term is suitably calculated by adopting emission factors from literature for varying conditions of street traffic. It is observed that increase in wind angle disturbs the symmetric pattern of pollution distribution along the street length. The concentration increases in the far end of the street as compared to the near end.
Abstract: This study examined the effects of neuromuscular
training (NT) on limits of stability (LOS) in female individuals.
Twenty female basketball amateurs were assigned into NT
experimental group or control group by volunteer. All the players were
underwent regular basketball practice, 90 minutes, 3 times per week
for 6 weeks, but the NT experimental group underwent extra NT with
plyometric and core training, 50 minutes, 3 times per week for 6 weeks
during this period. Limits of stability (LOS) were evaluated by the
Biodex Balance System. One factor ANCOVA was used to examine
the differences between groups after training. The significant level for
statistic was set at p
Abstract: The increasing interest in plant sterol enriched foods
is due to the fact that they reduce blood cholesterol concentrations
without adverse side effects. In this context, enriched foods with
phytosterols may be helpful in protecting population against
atherosclerosis and cardiovascular diseases. The aim of the present
work was to evaluate in a population of Viseu, Portugal, the
consumption habits low-fat, plant sterol-enriched yoghurt. For this
study, 577 inquiries were made and the sample was randomly
selected for people shopping in various supermarkets. The
preliminary results showed that the biggest consumers of these
products were women aged 45 to 65 years old. Most of the people
who claimed to buy these products consumed them once a day. Also,
most of the consumers under antidyslipidemic therapeutics noticed
positive effects on hypercholesterolemia.
Abstract: Knowledge modelling, a main activity for the development of Knowledge Based Systems, have no set standards and are mostly done in an ad hoc way. There is a lack of support for the transition from abstract level to implementation. In this paper, a methodology for the development of the knowledge model, which is inspired by both Software and Knowledge Engineering, is proposed. Use of UML which is the de-facto standard for modelling in the software engineering arena is explored for knowledge modelling. The methodology proposed, is used to develop a knowledge model of a knowledge based system for recommending suitable hotels for tourists visiting Mauritius.
Abstract: The manufacture of large-scale precision aerospace
components using CNC requires a highly effective maintenance
strategy to ensure that the required accuracy can be achieved over
many hours of production. This paper reviews a strategy for a
maintenance management system based on Failure Mode Avoidance,
which uses advanced techniques and technologies to underpin a
predictive maintenance strategy. It is shown how condition
monitoring (CM) is important to predict potential failures in high
precision machining facilities and achieve intelligent and integrated
maintenance management. There are two distinct ways in which CM
can be applied. One is to monitor key process parameters and
observe trends which may indicate a gradual deterioration of
accuracy in the product. The other is the use of CM techniques to
monitor high status machine parameters enables trends to be
observed which can be corrected before machine failure and
downtime occurs.
It is concluded that the key to developing a flexible and intelligent
maintenance framework in any precision manufacturing operation is
the ability to evaluate reliably and routinely machine tool condition
using condition monitoring techniques within a framework of Failure
Mode Avoidance.
Abstract: Shape memory alloy (SMA) actuators have found a
wide range of applications due to their unique properties such as high
force, small size, lightweight and silent operation. This paper presents
the development of compact (SMA) actuator and cooling system in
one unit. This actuator is developed for multi-fingered hand. It
consists of nickel-titanium (Nitinol) SMA wires in compact forming.
The new arrangement insulates SMA wires from the human body by
housing it in a heat sink and uses a thermoelectric device for rejecting
heat to improve the actuator performance. The study uses
optimization methods for selecting the SMA wires geometrical
parameters and the material of a heat sink. The experimental work
implements the actuator prototype and measures its response.